1. DL manuals
  2. Panasonic
  3. Telephone Accessories
  4. KX-TD1232
  5. Installation Manual

Panasonic KX-TD1232 Installation Manual

Manual is about: Digital Super Hybrid System

Summary of KX-TD1232

  • Page 1

    Kx-td816 model kx-td1232 digital super hybrid system installation manual d1232 digital super hybrid system panasonic panasonic d816 digital super hybrid system thank you for purchasing this panasonic model kx-td816/kx-td1232, digital super hybrid system. Please read this manual before connecting the...

  • Page 2: System Components

    2 system components system components system components table model description service unit kx-td816 kx-td1232 digital super hybrid system (main unit) digital super hybrid system (main unit) telephone kx-t7425 kx-t7433 kx-t7436 kx-t7450 kx-t7220 kx-t7230 kx-t7235 kx-t7250 kx-t7130 kx-t7020 kx-t7030...

  • Page 3

    System components 3 * 1 can be installed in the kx-td816 only. * 2 can be installed in the kx-td1232 only. Note • in this manual, the suffix of each model number are omitted. • if your main unit is the kx-tdn1232, refer to the information of the kx-td1232 in this manual. Optional equipment kx-t7440 ...

  • Page 4: Important Information

    4 important information important information when using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: a) read and understand all instructions. B) follow all warnings and instruc...

  • Page 5

    Important information 5 4) if the product does not operate normally by following the operating instructions. Adjust only those controls, that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualif...

  • Page 6: Attention

    6 attention attention • keep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the digital super hybrid system. • this unit should be kept free of dust, moisture, ...

  • Page 7

    Attention 7 • to prevent fire or shock hazard, do not expose this unit to rain or moisture. The serial number of this product may be found on the label affixed to the bottom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record o...

  • Page 8: Introduction

    8 introduction introduction this installation manual provides technical information for the panasonic digital super hybrid system, kx-td816 / kx-td1232. It is designed to serve as an overall technical reference for the system and includes a description of the system, its hardware and software, featu...

  • Page 9

    Introduction 9 along with this installation manual, the following manuals are available to help you know the available features, programme and use the kx-td816 / kx-td1232 system. Features guide provides information about the system features. Programming guide provides system programming instruction...

  • Page 10: Table of Contents

    10 table of contents table of contents 1 system outline 1.1 system highlights ........................................................................................................ 14 1.1.1 system highlights .............................................................................................

  • Page 11

    Table of contents 11 2.4.11 slt message waiting lamp adaptor unit connection..........................................111 2.4.12 system connection..................................................................................................120 2.4.13 backup battery and adaptor card connection......

  • Page 12

    12 table of contents.

  • Page 13: Section

    System outline 13 section 1 system outline.

  • Page 14: 1.1

    1.1 system highlights 14 system outline 1.1 system highlights 1.1.1 system highlights system maximum capacity actual capacity will depend on the number or/and type of units connected to the system. Module expansion expansion modules are used to increase the system capacity. Extra device port (xdp) e...

  • Page 15

    1.1 system highlights system outline 15 system connection *1 with the addition of the optional system inter connection card, two digital super hybrid systems can be connected together to double the capacity of the system. The two systems function as one, therefore, some functions such as paging and ...

  • Page 16: 1.2

    1.2 basic system construction 16 system outline 1.2 basic system construction 1.2.1 basic system construction the kx-td816 digital super hybrid system has a basic capacity of four outside lines and eight extensions, and the kx-td1232 has eight outside lines and 16 extensions. They are capable of sup...

  • Page 17: 1.2.2

    1.2 basic system construction system outline 17 1.2.2 system connection diagram kx-td816 panasonic d816 digital super hybrid system panasonic panasonic doorphone 1 doorphone kx-t30865 external music source amplifier printer for smdr or personal computer for system programming battery adaptor kx-a46 ...

  • Page 18

    1.2 basic system construction 18 system outline note • it is recommended that extension of jack 1 is a display proprietary telephone. • parallel connection of telephones is possible. Refer to section 2.3.3 parallelled telephone connection. Panasonic panasonic kx-t7400 series digital proprietary tele...

  • Page 19

    1.2 basic system construction system outline 19 kx-td1232 d1232 digital super hybrid system panasonic panasonic panasonic doorphone 1 doorphone kx-t30865 external music source 1 amplifier printer for smdr or personal computer for system programming battery adaptor kx-a46 to ac outlet two car batteri...

  • Page 20

    1.2 basic system construction 20 system outline note • it is recommended that extension of jack 1 is a display proprietary telephone. • parallel connection of telephones is possible. Refer to section 2.3.3 parallelled telephone connection. Panasonic panasonic kx-t7400 series digital proprietary tele...

  • Page 21: 1.3

    1.3 proprietary telephones system outline 21 1.3 proprietary telephones 1.3.1 proprietary telephones the following panasonic proprietary telephones are available with this system. Note • flexible co : flexible co button (programmable) • pf : programmable feature button proprietary telephone descript...

  • Page 22: 1.4

    1.4 options 22 system outline 1.4 options 1.4.1 options model no. Model name description max. Quantity on kx- td816 max. Quantity on kx-td1232 single system system connection kx-td170 8-station line unit adds 8 extension lines. 1 2 4 kx-td174 16 slt line circuit unit adds 16 extension lines which co...

  • Page 23

    1.4 options system outline 23 kx-td194 slt message waiting lamp adaptor unit supports the message waiting feature for a single line telephone with a message waiting lamp. One unit supports 16 extensions. 1 3 6 kx-td196 remote card supports the programming and maintenance of the system from a remote ...

  • Page 24

    1.4 options 24 system outline kx-a46 battery adaptor supports the connection of two car batteries for power backup in the event of a power failure. 1 1 2 kx-t7440 / kx-t7240 digital dss console provides easy and quick access to extensions and features. This must be used with a proprietary telephone....

  • Page 25: 1.4.2

    1.4 options system outline 25 1.4.2 expansion unit combination kx-td816 kx-td1232 master system basic (no unit connected) kx-td17x kx-td180 / kx-td184 / kx-td185 kx-td188 kx-td28x kx-td290 kx-td28x kx-td188 kx-td180 / kx-td184 / kx-td185 kx-td17x kx-td290 basic (no unit connected) kx-td17x kx-td180 ...

  • Page 26

    1.4 options 26 system outline kx-td1232 slave system note • : combination possible; : combination not possible; shaded part: these combinations shown elsewhere in the table. X: any number (e.G. Kx-td28x can be kx-td280 or kx-td286) • the kx-td188 and kx-td290 can only be connected to the master syst...

  • Page 27: 1.5

    1.5 specifications system outline 27 1.5 specifications 1.5.1 general description control method cpu: 16-bit cpu switching non blocking pcm time switch power supplies primary kx-td816bx: 110 vac - 115 vac / 200 vac / 220 vac / 240 vac, 50 hz / 60 hz kx-td816hk: 220 vac – 230 vac, 50 hz kx-td1232(d)b...

  • Page 28

    1.5 specifications 28 system outline extension connection cable single line telephones 1 pair wire (t, r) kx-t7425, kx-t7433, kx-t7436, kx-t7450, kx-t7220, kx-t7230, kx-t7235, kx-t7250 1 pair wire (d1, d2) or 2 pair wire (t, r, d1, d2) kx-t7130 (with the kx-td816), kx-t7020, kx-t7030, kx-t7033, kx-t...

  • Page 29: 1.5.2

    1.5 specifications system outline 29 1.5.2 characteristics station loop limit proprietary telephone: 40 single line telephone: 600 including set doorphone: 20 minimum leakage resistance 15 000 maximum number of station instruments per line 1 for proprietary telephone or single line telephone 2 by pa...

  • Page 30: 1.5.3

    1.5 specifications 30 system outline 1.5.3 system capacity line actual capacity will depend on the number or/and type of units connected to the system. User-supplied equipment item max. Quantity on kx-td816 max. Quantity on kx-td1232 single system system connection doorphones 2 2 4 door openers 2 2 ...

  • Page 31

    1.5 specifications system outline 31 system data item max. Quantity operators 2 system speed dialling 500 one-touch dialling 24 per extension (proprietary telephone) station speed dialling 10 per extension call park areas 10 absent messages 9 outside line groups 8 toll restriction levels 8 extension...

  • Page 32

    1.5 specifications 32 system outline.

  • Page 33: Section

    General installation 33 section 2 general installation.

  • Page 34: 2.1

    2.1 before installation 34 general installation 2.1 before installation 2.1.1 before installation please read the following notes concerning installation and connection before installing the system and terminal equipment. Safety installation instructions when installing telephone wiring, basic safet...

  • Page 35

    2.1 before installation general installation 35 wiring precautions be sure to follow these instructions when wiring the unit: a) do not wire the telephone cable in parallel with an ac power source, computer, telex, etc. If the cables are run near those wires, shield the cables with metal tubing or u...

  • Page 36: 2.2

    2.2 installation of the main unit 36 general installation 2.2 installation of the main unit 2.2.1 unpacking unpack the box and check the items below: kx-td816 kx-td1232 main unit one one ac cord one one template one one screws (wall mounting) three four anchor plug three four pager connectors — two ...

  • Page 37: 2.2.2

    2.2 installation of the main unit general installation 37 2.2.2 location of interfaces overview kx-td816 kx-td1232 d816 digital super hybrid system panasonic external music jack paging jack system clear switch reset button serial interface (rs-232c) connector ground terminal battery adaptor connecto...

  • Page 38

    2.2 installation of the main unit 38 general installation inside view kx-td816 kx-td1232 (4-pin / 6-pin connector type) extension 4-pin jacks fuse front cover outside line 4-pin jacks outside line 4-pin jacks extension 6-pin jacks paging jack 2 paging jack 1 external music jack 2 external music jack...

  • Page 39

    2.2 installation of the main unit general installation 39 kx-td1232 (modular / amphenol connector type) outside line modular jacks extension amphenol connectors paging jack 2 paging jack 1 external music jack 2 external music jack 1 system clear switch reset button front cover.

  • Page 40

    2.2 installation of the main unit 40 general installation power supply for kx-td816bx check the voltage selector to confirm if it is set to your house hold ac voltage. If not, reset the voltage selector on the back of the main unit to the correct position with a screwdriver. Power adaptor for kx-td8...

  • Page 41: 2.2.3

    2.2 installation of the main unit general installation 41 2.2.3 wall mounting this set is designed for wall mounting only. The wall where the main unit is to be mounted must be able to support the weight of the main unit. If screws other than the ones supplied are used, use screws with the same diam...

  • Page 42

    2.2 installation of the main unit 42 general installation mounting on concrete or mortar wall 1. Place the template (included) on the wall to mark the screw positions. 2. Drill holes and drive the anchor plugs (included) with a hammer, flush to the wall. 3. Install the screws (included) into the anc...

  • Page 43: 2.2.4

    2.2 installation of the main unit general installation 43 2.2.4 frame ground connection important connect the frame of the main unit to ground. 1. Loosen the screw. 2. Insert the grounding wire. 3. Tighten the screw. 4. Connect the grounding wire to ground. To ground panasonic d816 digital super hyb...

  • Page 44: 2.2.5

    2.2 installation of the main unit 44 general installation 2.2.5 opening the front cover 1. Loosen the two screws on the right side of the main unit. 2. Open the front cover in the direction of arrow . Note the two screws are attached to the front cover with springs so that they will not be lost. A d...

  • Page 45: 2.3

    2.3 connection general installation 45 2.3 connection 2.3.1 outside line connection there are two methods to perform outside line connection, using a 4-pin connector and a modular connector. Which method should be used depends on the model number of the system as shown below. Method 1: using 4-pin c...

  • Page 46

    2.3 connection 46 general installation kx-td816 kx-td1232 outside line 4 outside line 3 outside line 2 outside line 1 t t r r to terminal board or modular jacks from the central office t t r r outside line 8 outside line 7 outside line 6 outside line 5 outside line 4 outside line 3 outside line 2 ou...

  • Page 47

    2.3 connection general installation 47 method 2: using modular connector (kx-td1232bx/hk/x) connection 1. Insert the modular plugs of the telephone line cords (4-conductor wiring) into the modular jacks on the system. 2. Connect the line cord to the terminal board or the central office jack. Notice ...

  • Page 48: 2.3.2

    2.3 connection 48 general installation 2.3.2 extension connection there are four methods to perform extension connection, using a 4-pin connector, a 6-pin connector and an amphenol connector. Which method should be used depends on the model number of the system as shown below. Maximum cabling distan...

  • Page 49

    2.3 connection general installation 49 telephone wiring for kx-td1232 2, 4 or 6-conductor wiring is required for each extension as listed below. There are six pins for possible connection: "t", "r", "d1", "d2", "p1" and "p2". T: tip r: ring d1: data 1 d2: data 2 p1: 3 pair voice (ohca) p2: 3 pair vo...

  • Page 50

    2.3 connection 50 general installation method 1: using 4-pin connector (for kx-td816) connection 1. Prepare the required plugs. Eight 4-pin plugs are included to connect extension lines. Note do not peel off the wire coating. Insert the wires all the way. 2. Insert the plug into an extension jack in...

  • Page 51

    2.3 connection general installation 51 method 2: using 6-pin connector (for kx-td1232dbx/ml, kx-tdn1232) wire specifications connection 1. Prepare the required plugs. Sixteen 6-pin plugs are included to connect extension lines. Note do not peel off the wire coating. Insert the wires all the way. 2. ...

  • Page 52

    2.3 connection 52 general installation method 3: using amphenol connector (for kx-td1232bx/hk/x) connection 1. Insert the 50-pin connector to the extension jack as shown. 2. Connect the wire cords to the appropriate connector pins and the terminal equipment. Refer to the telephone wiring (page 50) a...

  • Page 53

    2.3 connection general installation 53 pin number chart t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r d1 d2 p1 p2 t r ...

  • Page 54

    2.3 connection 54 general installation note • "8extn" in the table indicates an extension expansion area for 8-station line unit (kx- td170). System programming is required for card location identification. [109]> • if a telephone or answering machine with an a-a1 relay is connected to the main unit...

  • Page 55: 2.3.3

    2.3 connection general installation 55 2.3.3 parallelled telephone connection any single line telephone can be connected in parallel with a proprietary telephone as follows: method 1: using a modular t-adaptor note • the kx-td1232 is illustrated as the main unit. • the 6-conductor wiring cord (and t...

  • Page 56

    2.3 connection 56 general installation method 2: for digital proprietary telephones only note • the kx-td1232 is illustrated as the main unit. • not only a single line telephone but a single line device such as an answering machine, a facsimile or a modem (personal computer) etc. Can be connected in...

  • Page 57: 2.3.4

    2.3 connection general installation 57 2.3.4 extra device port (xdp) connection a digital proprietary telephone and a single line telephone can be connected to the same extension jack yet have different extension numbers (extra device port feature). System programming is required for this jack. Meth...

  • Page 58: 2.3.5

    2.3 connection 58 general installation 2.3.5 polarity sensitive telephone connection if your telephone is polarity sensitive, follow the procedure below: 1. Complete all the required extension wiring. 2. Confirm that dialling can be done from all the extensions using a touch-tone telephone. If diall...

  • Page 59

    2.3 connection general installation 59 7. Reverse as shown. 8. Every time an extension telephone is replaced, repeat the above procedure. Note the kx-td1232 is illustrated as the main unit. D1232 digital super hybrid system 1 2 3 4 5 6 7 8 9 0 # central office line reverse here. Extension.

  • Page 60: 2.3.6

    2.3 connection 60 general installation 2.3.6 external pager (paging equipment) connection kx-td816 one external pager (user-supplied) can be connected to the kx-td816 as illustrated below. Use an rca connector and shielded cable. • output impedance: 600 maximum length of the cable awg 18 – 22: under...

  • Page 61

    2.3 connection general installation 61 kx-td1232 up to two external pagers (user-supplied) can be connected to the kx-td1232 per system as illustrated below. Use an rca connector and shielded cable. • output impedance: 600 maximum length of the cable awg 18 – 22: under 10 m note • system connection ...

  • Page 62: 2.3.7

    2.3 connection 62 general installation 2.3.7 external music source connection kx-td816 one music source such as a radio (user-supplied) can be connected to the kx-td816 as illustrated below. Insert the plug to the earphone / headphone jack on the external music source. Use a two- conductor plug (3.5...

  • Page 63

    2.3 connection general installation 63 kx-td1232 up to two music sources such as a radio (user-supplied) can be connected to the kx-td1232 per system as illustrated below. Insert the plug to the earphone / headphone jack on the external music source. Use a two-conductor plug (3.5 mm in diameter). • ...

  • Page 64: 2.3.8

    2.3 connection 64 general installation 2.3.8 printer and pc connection a user-supplied printer or personal computer (pc) can be connected to the system. These are used to print out or refer to the station message detail recording (smdr) call records and system programming data. Connect the printer c...

  • Page 65

    2.3 connection general installation 65 connection chart for printer / ibm *1 personal computer if you connect a printer or a pc with a 25-pin cable, follow the chart below. If you connect a printer or an ibm-pc with a 9-pin cable, follow the chart below. Note please read your printer manual and conn...

  • Page 66

    2.3 connection 66 general installation serial interface (rs-232c) signals frame ground: fg connects to the unit frame and the earth ground conductor of the ac power cord. Transmitted data: sd (txd): (output) conveys signals from the unit to the printer. A "mark" condition is held unless data or brea...

  • Page 67: 2.3.9

    2.3 connection general installation 67 2.3.9 installation of lightning protectors overview a lightning protector is a device to be installed on an outside line to prevent a dangerous surge from entering the building and damaging equipment. A dangerous surge can occur if a telephone line comes in con...

  • Page 68

    2.3 connection 68 general installation outside installation diagram if you install an extension outside of the main building, the following precautions are recommended: a) install the extension wire underground. B) use a conduit to protect the wire. Note the lighting protector for an extension is di...

  • Page 69

    2.3 connection general installation 69 earth rod installation diagram 1. Installation location of the earth rod: near the protector 2. Check obstructions: none 3. Composition of the earth rod: metal 4. Depth of the earth rod: more than 50 cm 5. Size of the grounding wire: thickness is more than 16 a...

  • Page 70: 2.4

    2.4 installation of optional cards and unit 70 general installation 2.4 installation of optional cards and unit 2.4.1 location of optional cards and units precaution to protect the printed circuit boards (p-boards) from static electricity, do not touch parts on the p-boards in the main unit and on t...

  • Page 71

    2.4 installation of optional cards and unit general installation 71 note • system programming is required for expansion unit location. Sys prg [109]> default: area 1 = 4-co line unit, area 2 = 8-station line unit. • it is also possible to attach the line expansion unit to the disa or remote unit and...

  • Page 72

    2.4 installation of optional cards and unit 72 general installation backup battery and adaptor card, doorphone card for kx-td816 caller id card for kx-td816 install doorphone card, kx-td160. This card connects two doorphones and two door openers. Install backup battery and adaptor card, kx-a216. Ope...

  • Page 73

    2.4 installation of optional cards and unit general installation 73 remote card, system inter connection card, disa card, doorphone card for kx- td1232 caller id card for kx-td1232 remote card connector system inter connection card connector disa card connector doorphone card connector front cover i...

  • Page 74

    2.4 installation of optional cards and unit 74 general installation slt message waiting lamp adaptor unit one slt message waiting lamp adaptor unit (kx-td194) for kx-td816, and up to three slt message waiting lamp adaptor units for kx-td1232 can be connected. This unit supports the message waiting f...

  • Page 75: 2.4.2

    2.4 installation of optional cards and unit general installation 75 2.4.2 4-co line unit connection to add four outside lines (outside lines 05 through 08 for kx-td816, and outside lines 09 through 12 for kx-td1232), use the optional 4-co line unit (kx-td180). This unit can be installed to any of th...

  • Page 76: 2.4.3

    2.4 installation of optional cards and unit 76 general installation 2.4.3 4-e&m (tie) line unit connection to add four e&m (tie) lines (outside lines 05 through 08 for kx-td816, and outside lines 09 through 12 for kx-td1232), use the optional 4-e&m (tie) line unit (kx-td184). This unit can be instal...

  • Page 77: 2.4.4

    2.4 installation of optional cards and unit general installation 77 2.4.4 4-did line unit connection to add four did lines, use the optional 4-did line unit (kx-td185). This unit adds did lines with the capability to accept dial pulse, dtmf and mfc-r2 signalling. The following unit types can be sele...

  • Page 78: 2.4.5

    2.4 installation of optional cards and unit 78 general installation 2.4.5 8-station line unit connection to add eight extensions (jack numbers 09 through 16 for kx-td816, and jack numbers 17 through 24 or 25 through 32 for kx-td1232), use the optional 8-station line unit (kx- td170). To add 16 exten...

  • Page 79: 2.4.6

    2.4 installation of optional cards and unit general installation 79 2.4.6 16 slt line circuit unit connection to add eight extensions which contain two single line telephones, use the optional 16 slt line circuit unit (kx-td174). The unit can support 16 single line telephones per unit. Each single l...

  • Page 80: 2.4.7

    2.4 installation of optional cards and unit 80 general installation 2.4.7 installing expansion unit the following procedures can be used to install the optional expansion units. The following steps 1 through 5 and 7 through 10 are the same for all expansion units. Step 6 is different for each unit. ...

  • Page 81

    2.4 installation of optional cards and unit general installation 81 3. Hook the cabinet on the main unit and slide the cabinet to the left until it is secured. 4. Loosen the outside screw and slide the cover to the right. 5. Secure the inside screw (included) to fix the cabinet to the main unit. Not...

  • Page 82

    2.4 installation of optional cards and unit 82 general installation 6. (if a option is to be installed) if a kx-td180d (for kx-td816, kx-td1232dbx/ml, kx-tdn1232) is to be installed; a) prepare the required 4-pin plugs. Note do not peel off the wire coating. Insert the wires all the way. B) insert t...

  • Page 83

    2.4 installation of optional cards and unit general installation 83 if a kx-td180 (for kx-td1232bx/hk/x) or a kx-td185 is to be installed; insert the modular plugs of the telephone line cords (4-conductor wiring) into the modular jacks on the unit. Note • did lines of the kx-td185 are polarity sensi...

  • Page 84

    2.4 installation of optional cards and unit 84 general installation if a kx-td184 is to be installed; insert the amphenol connector into the jack. Note • for fixing the connector, see "amphenol 57je type (screw-attach-type 50-pin connector) connection" on page 88. • for jack connection, please see "...

  • Page 85

    2.4 installation of optional cards and unit general installation 85 if a kx-td170d (for kx-td816, kx-td1232dbx/ml, kx-tdn1232) is to be installed; a) prepare the required 6-pin plugs. Note do not peel off the wire coating. Insert the wires all the way. B) insert the plug into a jack on the unit. Not...

  • Page 86

    2.4 installation of optional cards and unit 86 general installation if a kx-td170 (for kx-td1232bx/hk/x) or a kx-td174 is to be installed; insert the amphenol connector into the jack. Note • for details about the jack for power failure transfer, refer to section 2.5.1 auxiliary connection for power ...

  • Page 87

    2.4 installation of optional cards and unit general installation 87 7. Tie all of the cords into a bundle. If other cords are exposed in the upper cabinets, tie them also. 8. Close the cabinet cover and secure the outside screw. 9. Cover the cords with the cord holder (included). 10. Fix the cords t...

  • Page 88

    2.4 installation of optional cards and unit 88 general installation amphenol 57je type (screw-attach-type 50-pin connector) connection to fix the amphenol 57je type (screw-attach type 50-pin connector) to the unit, follow the procedure below. 1. The 50-pin connector (jack) on the expansion unit has ...

  • Page 89

    2.4 installation of optional cards and unit general installation 89 2. To attach the amphenol 57je type (plug) to the connector, drive the accessory screw into the upper part. Fasten the accessory wire tie around the lower hook-pin and the amphenol 57je type, as shown. Accessory screw amphenol 57je ...

  • Page 90

    2.4 installation of optional cards and unit 90 general installation pin number chart for the kx-td174 pin no. 26 1 27 2 28 3 29 4 30 5 31 6 32 7 33 8 34 9 35 10 36 11 37 12 38 13 39 14 40 15 41 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 t r t r t r t r ...

  • Page 91

    2.4 installation of optional cards and unit general installation 91 e&m (tie) line connection a) unit specifications item description e&m (tie) line types type 5 only transmission 2-wire or 4-wire voice path (programmable) (note) maximum cabling distance of the e&m line cord (twisted cable): 22 awg:...

  • Page 92

    2.4 installation of optional cards and unit 92 general installation b) pin number chart (e&m line) note 21-25, 46-50: cannot be connected pin no. 1 26 2 27 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 orn-red orn-blk yel-red yel-blk gry-red gry...

  • Page 93

    2.4 installation of optional cards and unit general installation 93 c) cable pins to be connected (e&m line) • e&m line wiring d) connecting to another kx-td816/kx-td1232 system (kx-td184) 1. 2-wire voice path 2. 4-wire voice path 26 1 27 2 28 3 29 4 30 5 31 6 1 2 3 4 5 6 7 8 9 11 12 1 2 3 4 5 6 7 8...

  • Page 94

    2.4 installation of optional cards and unit 94 general installation e) connecting to the e&m central office 1. 2-wire voice path 2. 4-wire voice path t r e m ground ground -48v -48v kx-td184 e&m central office t1 r t r1 e m ground ground -48 v -48 v voice transmit voice receive voice transmit voice ...

  • Page 95

    2.4 installation of optional cards and unit general installation 95 f) e&m sequences you can choose one of the following e&m sequences. 1. Continuous e&m 2. Pulsed e&m with answer signal 3. Pulsed e&m without answer signal wink seize dial answer disconnect if you select immediate, this signal will n...

  • Page 96: 2.4.8

    2.4 installation of optional cards and unit 96 general installation 2.4.8 caller id card installation installing to the initial co line card 1. Loosen four screws for kx-td816 or eight screws for kx-td1232 to open the inside cover of the main unit. Note if any cards, units, or cords are installed in...

  • Page 97

    2.4 installation of optional cards and unit general installation 97 kx-td1232 3. Put the inside cover back on the main unit and secure the screws. Kx-td193 caller id kx-td193 caller id co line card inside cover caller id cards.

  • Page 98

    2.4 installation of optional cards and unit 98 general installation installing to the optional 4-co line unit the following procedures must be done before installing the 4-co line unit (kx-td180) to the main unit. 1. Loosen five screws located on the rear of the 4-co line unit. 2. Remove the back pl...

  • Page 99: 2.4.9

    2.4 installation of optional cards and unit general installation 99 2.4.9 disa card / unit and remote card / unit installation the disa card (kx-td191 and kx-td199), disa unit (kx-td190), remote card (kx- td196), high speed remote card (kx-td197) and remote unit (kx-td198) can be installed as follow...

  • Page 100

    2.4 installation of optional cards and unit 100 general installation 2. Connect the cabinet cord to the connector in the main unit firmly. 3. Hook the cabinet onto the main unit and slide the cabinet to the left until it is secured. It is possible to install the required card in the unit before inst...

  • Page 101

    2.4 installation of optional cards and unit general installation 101 3. Turn over the unit again and remove the inside cover. 4. Install the card, secure the screw (included with the unit) and connect the cable to the connector. 5. Flatten the cable to replace the inside cover properly. 6. Replace t...

  • Page 102

    2.4 installation of optional cards and unit 102 general installation 1. Remove the front cover of the disa or remote unit. The kx-td198 users must set the mode switch to 2. 2. Attach the expansion unit to the disa or remote unit as shown below. Be sure to connect the cabinet cords by inserting the e...

  • Page 103

    2.4 installation of optional cards and unit general installation 103 4. Hook the cabinets onto the main unit and slide the cabinets to the left until they are secured. 5. Loosen the outside screw of the expansion unit and slide the cover to the right. 6. Secure the inside screw (included with the di...

  • Page 104

    2.4 installation of optional cards and unit 104 general installation 10. Fix the cords to the wall as shown here, so that the front cover can be opened. Kx-td1232 1. Insert the upper side of the disa card into the two hooks on the main unit. 2. Press down the two corners of the lower side of the dis...

  • Page 105

    2.4 installation of optional cards and unit general installation 105 1. Insert the upper side of the remote card into the two hooks on the main unit. 2. Press down the two corners of the lower side of the remote card. 3. Connect the cord to the remote card connector. Features guide references system...

  • Page 106: 2.4.10

    2.4 installation of optional cards and unit 106 general installation 2.4.10 doorphone and door opener connection to connect up to two doorphones (kx-t30865) and up to two door openers (user-supplied), a doorphone card (kx-td160) is required. Installing the doorphone 1. Loosen the screw to separate t...

  • Page 107

    2.4 installation of optional cards and unit general installation 107 doorphone card installation 1. Connect a 4-conductor modular connector to the doorphone card cabinet, and pass the cord through the groove in the cabinet. 2. Attach the doorphone card cabinet to the main unit and press down. 3. Con...

  • Page 108

    2.4 installation of optional cards and unit 108 general installation wiring of the doorphone 1. Connect the doorphone card to the terminal box using a 4-conductor modular connector. 2. Connect the wires of doorphone 1 to the red and green screws of the terminal box. 3. Connect the wires of doorphone...

  • Page 109

    2.4 installation of optional cards and unit general installation 109 2. Loosen the screws on the terminal strip. 3. Insert the wires coming from the door openers into holes and tighten the screws. Note • the kx-td1232 is illustrated as the main unit. • for wiring, ul 1015, awg 22 twisted wire or the...

  • Page 110

    2.4 installation of optional cards and unit 110 general installation maximum cabling distance of the doorphone and the door opener line the maximum length of the doorphone and door opener line that connects to the main unit is shown below: note the kx-td1232 is illustrated as the main unit. Programm...

  • Page 111: 2.4.11

    2.4 installation of optional cards and unit general installation 111 2.4.11 slt message waiting lamp adaptor unit connection name and locations specifications 1. General description capacity corresponding extensions 16 control method cpu: one-chip microcomputer interface: 1-apt interface power suppl...

  • Page 112

    2.4 installation of optional cards and unit 112 general installation 2. Characteristics warning this unit may only be installed and serviced by qualified service personnel. Wall mounting this unit can be mounted to a wall. Refer to section 2.2.3 wall mounting for details. Dc power supply to stations...

  • Page 113

    2.4 installation of optional cards and unit general installation 113 opening the front cover 1. Loosen the screw. 2. Slide the cover while pressing the mark. Note the screw cannot be removed from the unit. Frame ground connection important connect the system frame to the ground. 1. Loosen the screw....

  • Page 114

    2.4 installation of optional cards and unit 114 general installation inserting the connector 1. Insert the two 50-pin connectors to the jacks as shown below. The connector "to system" should be connected to the cable which is connected to the kx-td816/kx-td1232. Also, the connector "to extn" should ...

  • Page 115

    2.4 installation of optional cards and unit general installation 115 3. If two units are connected with the dc in/out or a battery adaptor (kx-a46) is connected to the unit, insert the 4-pin connectors to the jacks as shown below. Also connect the ground terminal of the unit to the minus (-) termina...

  • Page 116

    2.4 installation of optional cards and unit 116 general installation pin number chart pin no. 26 1 27 2 to system connector (cn1) to extension connector (cn2) apt data extn. 01 extn. 01 extn. 02 extn. 02 extn. 03 extn. 03 extn. 04 extn. 04 extn. 05 extn. 05 extn. 06 extn. 06 extn. 07 extn. 07 extn. ...

  • Page 117

    2.4 installation of optional cards and unit general installation 117 pin connection example there are various pin connection patterns depending on the combination of the connecting units. The example below is the case that one kx-td194 is connected to the kx-td1232 with a message waiting lamp can co...

  • Page 118

    2.4 installation of optional cards and unit 118 general installation closing the front cover 1. Fasten the binders. 2. Replace the cover and tighten the screw. 3. Tie together all of the connected cords and attach them to the wall so that the cords cannot be pulled out of the system. Screw.

  • Page 119

    2.4 installation of optional cards and unit general installation 119 starting the unit plug the ac cord into the system ac inlet and an ac outlet. Avoid sharing the ac outlet of this system with other office equipment. Use a dedicated ac outlet only. Caution the power supply cord is used as the main...

  • Page 120: 2.4.12

    2.4 installation of optional cards and unit 120 general installation 2.4.12 system connection *1 to connect two main units, use two optional system inter connection cards (kx-td192) and the connection cable (included in the cards). 1. Insert the upper side of the system inter connection card into tw...

  • Page 121

    2.4 installation of optional cards and unit general installation 121 7. Close the latches on both systems. 8. Open the rom cover in the slave system and set the master/slave switch on the cpu card to "slave" position. 9. Turn the power on. Note • system connection may take a while (5 to 15 min depen...

  • Page 122: 2.4.13

    2.4 installation of optional cards and unit 122 general installation 2.4.13 backup battery and adaptor card connection *1 the optional backup battery and adaptor card (kx-a216) is a backup power supply to operate all the features in the event of a power failure. In case of power failure, the battery...

  • Page 123

    2.4 installation of optional cards and unit general installation 123 3. Fasten the nylon belt to fix the battery. Fix the adaptor card by a screw (included). 4. Connect the cord of battery to the adaptor card. Remove the backup battery connector cover on the main unit. Then connect the cord of the a...

  • Page 124: 2.4.14

    2.4 installation of optional cards and unit 124 general installation 2.4.14 battery adaptor connection user-supplied car batteries can be used as a backup power supply in the event of a power failure. In case of a power failure, the batteries automatically maintain power to the main unit. The option...

  • Page 125

    2.4 installation of optional cards and unit general installation 125 2. Insert the plug of the battery adaptor into the battery adaptor connector on the main unit. Connect the ground wire to the ground terminal on the main unit. 3. Turn on the power switch of the battery adaptor. Wall mounting 1. Dr...

  • Page 126

    2.4 installation of optional cards and unit 126 general installation 5. Hook the battery adaptor onto the screw heads. Mounting on concrete or mortar walls; at step 4, drill two holes and drive the anchor plugs with a hammer, flush to the wall, and install the big screws into the anchor plugs. Note ...

  • Page 127: 2.5

    2.5 auxiliary connection for power failure transfer general installation 127 2.5 auxiliary connection for power failure transfer 2.5.1 auxiliary connection for power failure transfer power failure transfer connects specific single line telephones to selected outside lines in the event of system powe...

  • Page 128

    2.5 auxiliary connection for power failure transfer 128 general installation note • in the event of a power failure, system memory is protected by a factory-provided lithium battery. There is no memory loss except the memories of camp-on, saved number redial, last number redial, call park and messag...

  • Page 129: 2.6

    2.6 closing the front cover general installation 129 2.6 closing the front cover 2.6.1 closing the front cover 1. Fasten all the cables and cords with the cord fastener. 2. Replace the cover and tighten the screw. Note be sure to tighten two screws, or the unit may not work properly. Panasonic d816 ...

  • Page 130

    2.6 closing the front cover 130 general installation 3. Tie together all of the connected cords and attach them to the wall so that the cords cannot be pulled out of the main unit. D1232 digital super hybrid system panasonic d816 digital super hybrid system.

  • Page 131: 2.7

    2.7 starting the system for the first time general installation 131 2.7 starting the system for the first time 2.7.1 starting the system for the first time 1. Set the power switch to the "off" position. 2. Set the system clear switch to the "clear" position. 3. Plug the ac power cord into the system...

  • Page 132

    2.7 starting the system for the first time 132 general installation kx-td1232 notice • after pressing the reset button, slide the system clear switch to the "normal" position at step 6 while the power indicator is flashing (within approximately 10 seconds). Otherwise, the system will not start up wi...

  • Page 133: 2.8

    2.8 system restart general installation 133 2.8 system restart 2.8.1 system restart after starting the system, if the system does not operate properly, restart the system. Before restarting the system, try the system feature again to confirm whether there definitely is a problem or not. System resta...

  • Page 134: 2.9

    2.9 system data clear 134 general installation 2.9 system data clear 2.9.1 system data clear after storing or changing the system programming data, it is possible to clear your programming data stored in the system, if required. The system will restart with the default setting. 1. Slide the system c...

  • Page 135: Section

    Isdn installation 135 section 3 isdn installation.

  • Page 136: 3.1

    3.1 isdn network outline 136 isdn installation 3.1 isdn network outline 3.1.1 overview to use the isdn line service, the following unit can be installed to the system. 2-isdn s0 line unit (kx-td280) this unit adds two basic rate interface (bri) isdn s0 lines. One kx-td280 can be connected to the kx-...

  • Page 137

    3.1 isdn network outline isdn installation 137 notice • the isdn line units (e.G. Kx-td280) are in accordance with the european telecommunication standards (ets). If your telephone company provides an isdn service which follows the standards other than ets, some isdn features in the features guide m...

  • Page 138: 3.2

    3.2 isdn line connection 138 isdn installation 3.2 isdn line connection 3.2.1 location of the units kx-td816 one isdn line unit (kx-td280 or kx-td286) can be installed to any expansion area. Note • system programming is required for expansion unit location. Sys prg [109]> default : area 1 = 4-co lin...

  • Page 139

    3.2 isdn line connection isdn installation 139 kx-td1232 one isdn line unit (kx-td280 or kx-td286) and/or one pri isdn line unit (kx- td290) can be installed to any expansion area. If you use the kx-td170 or kx-td174 with the kx-td290, you must use the kx-td170- or kx-td174- . The former unit does n...

  • Page 140: 3.2.2

    3.2 isdn line connection 140 isdn installation 3.2.2 installing the unit step 6 is different for each unit. The isdn unit should not be installed only to the slave system. The kx-td1232 is illustrated as the main unit. 1. Loosen two screws on the cover plate. Insert fingers into the slits to remove ...

  • Page 141

    3.2 isdn line connection isdn installation 141 3. Hook the cabinet to the main unit and slide the cabinet to the left until it is secured. 4. Loosen the outside screw and slide the cover to the right. 5. Secure the inside screw (included) to fix the cabinet to the main unit. Note be sure to fix the ...

  • Page 142

    3.2 isdn line connection 142 isdn installation 6. If a kx-td280 or kx-td286 is to be installed: a) prepare the required plugs. Two 4-pin plugs are included in kx-td280, and six 4-pin plugs are included in kx-td286 to connect outside lines. Note do not peel off the wire coating. Insert the wires all ...

  • Page 143

    3.2 isdn line connection isdn installation 143 a) prepare the required plugs. Two 4-pin plugs are included with the kx-td290. Note do not peel off the wire coating. Insert the wires all the way. B) insert the plug into a jack on the unit. Connect a grounding wire to the ground terminal on the extens...

  • Page 144

    3.2 isdn line connection 144 isdn installation 9. Cover the cords with the cord holder (included). 10. Fix the cords to the wall as shown so that the front cover can be opened. Note if two or three expansion units are installed, cut the cabinet covers on the lower cabinets to allow the cords from th...

  • Page 145: 3.2.3

    3.2 isdn line connection isdn installation 145 3.2.3 internal isdn s0 line connection the isdn s0 bus on the 2-isdn s0 line unit (kx-td280) and the 6-isdn s0 line unit (kx-td286) can be used as internal s0 bus. Each port can be used as either external or internal isdn s0 lines. Some system programme...

  • Page 146

    3.2 isdn line connection 146 isdn installation 3. Connect the lines between the isdn board and the isdn device. 4. Plug the ac power cord into the system and an ac outlet. 5. Programme [423] isdn port type and other required programmes in system programming. 6. Press the reset button with a pointed ...

  • Page 147

    3.2 isdn line connection isdn installation 147 wiring with terminating resistors (tr) the isdn s0 bus should be terminated with two100 terminating resistors (tr). Power supply for isdn terminal equipment (te) the system does not provide a power supply to terminal equipment (te). Depending on the typ...

  • Page 148

    3.2 isdn line connection 148 isdn installation.

  • Page 149: Section

    E1 installation 149 section 4 e1 installation.

  • Page 150: 4.1

    4.1 e1 line service outline 150 e1 installation 4.1 e1 line service outline 4.1.1 overview to use the e1 line service, the following unit is required. E1 unit (kx-td188) this unit adds one e1 line which adds 30 channels (outside lines 24 through 54) to the system. One kx-td188 can installed to the k...

  • Page 151: 4.2

    4.2 e1 line installation e1 installation 151 4.2 e1 line installation 4.2.1 location of the unit one e1 unit (kx-td188) can be installed to any expansion area on the kx-td1232 master system. If you use the kx-td170 or kx-td174 with the kx-td188, you must use the kx-td170- or kx-td174- . The former u...

  • Page 152: 4.2.2

    4.2 e1 line installation 152 e1 installation 4.2.2 location of interfaces send lead receive lead e1 ports rx tx.

  • Page 153: 4.2.3

    4.2 e1 line installation e1 installation 153 4.2.3 installing the unit installing one unit to the system allows one e1 line to be connected to outside lines 25 through 54 for the kx-td1232 master system. 1. Loosen two screws on the cover plate. Insert fingers into the slits to remove the cover plate...

  • Page 154

    4.2 e1 line installation 154 e1 installation 3. Hook the cabinet to the main unit and slide the cabinet to the left until it is secured. 4. Loosen the outside screw and slide the cover to the right. 5. Secure the inside screw (included) to fix the cabinet to the main unit. Note be sure to fix the in...

  • Page 155

    4.2 e1 line installation e1 installation 155 6. Insert the coaxial plug of the telephone line cords (2 coaxial cables) into the coaxial jack (e1 port). A. Align the plug with the jack and push in the plug. B. Twist the plug until it locks on the connector. 7. Tie all of the cords into a bundle. If o...

  • Page 156

    4.2 e1 line installation 156 e1 installation 10. Fix the cords to the wall as shown so that the front cover can be opened. Note if two or three expansion units are installed, cut the cabinet covers on the lower cabinets to allow the cords from the upper cabinet to go down through the cabinet covers....

  • Page 157: Section

    Troubleshooting 157 section 5 troubleshooting.

  • Page 158: 5.1

    5.1 troubleshooting 158 troubleshooting 5.1 troubleshooting 5.1.1 installation problem probable cause possible solution extension does not operate. Bad printed circuit board (extension card). Exchange printed circuit board for another printed circuit board. Bad connection between the system and exte...

  • Page 159: 5.1.2

    5.1 troubleshooting troubleshooting 159 5.1.2 connection can you dial an extension? The t/r is connected to the d1/d2. Use the correct cord (inner 2 wires are for t/r and the outer 2 wires are for d1/d2). Kx-td816/ extension kx-td1232 kx-td1232 extension cause solution use the correct cord (2 second...

  • Page 160

    5.1 troubleshooting 160 troubleshooting t2 r1 t1 r2 can you dial out on an outside line? No outside lines are connected to the t2/t1. Connection between the central office and the system: (continued from the previous.) reconnect the outside lines to the t1/r1 or t2/r2 of the telephone jack using 2- ...

  • Page 161

    5.1 troubleshooting troubleshooting 161 can you dial out on an e1 line? No wrong wiring combination. Connection between the central office and the system: reconnect correctly as follows. Cause solution tx rx tx rx outside line kx-td1232 tx rx tx rx outside line kx-td1232.

  • Page 162: 5.1.3

    5.1 troubleshooting 162 troubleshooting 5.1.3 operation problem probable cause possible solution • when using the speakerphone mode with a analogue proprietary telephone, nothing is audible. • the handset / headset selector is set to the "headset" position. • when the headset is not used, set the ha...

  • Page 163: 5.1.4

    5.1 troubleshooting troubleshooting 163 5.1.4 using the reset button if the system does not operate properly, use the reset button. (if master and slave systems are in operation by system connection for kx-td1232, reset both systems.) before using the reset button, try the system feature again to co...

  • Page 164

    5.1 troubleshooting 164 troubleshooting kx-td816 extension (t, r) of jack number 01: outside line 01 extension (t, r) of jack number 02: outside line 02 extension (t, r) of jack number 09: outside line 05 extension (t, r) of jack number 10: outside line 06 kx-td1232 extension (t, r) of jack number 0...

  • Page 165: Section

    Index 165 section 6 index.

  • Page 166

    166 index numerics 16 slt line circuit unit (kx-td174) 22, 70, 71, 79 16 slt line circuit unit connection 79 2-isdn s0 line unit (kx-td280) 22, 136, 138, 139, 142, 145 4-co line unit (kx-td180) 22, 70, 71, 75, 82, 83 4-co line unit connection 75 4-did line unit (kx-td185) 22, 70, 71, 77 4-did line u...

  • Page 167

    Index 167 kx-td192 (system inter connection card) 22, 73, 120 kx-td193 (caller id card) 22, 72, 73, 96 kx-td194 (slt message waiting lamp adaptor unit) 23, 74, 111 kx-td196 (remote card) 23, 73, 99, 105 kx-td197 (high speed remote card) 23, 70, 73, 99, 100, 105 kx-td198 (remote unit) 23, 70, 99, 102...

  • Page 168

    Kyushu matsushita electric co., ltd. 1-62, 4-chome, minoshima, hakata-ku, fukuoka 812-8531, japan printed in japan psqx2110za warning: this is a class a product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Copy...