Digital super hybrid system kx-td816 kx-td1232 installation quick guide for kx-td7590ce.
2 table of contents 1.0 dect programming ( ps registration )........................................................................ 3 2.0 site survey................................................................................................................. 7 note this guide shows you the addi...
3 1.0 dect programming [650] ps registration description assigns a registration number and an extension number to each ps. Display pt and the ps whose registration number is to be set are required for this programme. Selection (with a display pt) • ps registration number: kx-td816 – 01 through 16 kx...
4 display (if disabled): rejected the cell station (cs) may not be connected or not working. After connecting the cs or resetting the pbx, wait for at least one minute and try again from the beginning. 6. Press the power button for a while (about 5 seconds). 7. Press the function button. 8. Press th...
5 enable disable 18. Press the select button. Display example: 19. If you select "enable" in step 17, enter a system lock password. 20. Press the auto/ok button. 21. Enter the system lock password again. 22. Press the auto/ok button. 23. To programme another ps, press next or prev, or select and the...
6 display example: dect-sys lock password =---- 6. Enter a system lock password and press the auto/ok button, if required. Display: dect-sys lock password =**** 7. Go to steps 11 through 25 of the “registering for the first time” programming. Conditions • you can assign an extension number to each p...
7 2.0 site survey assigning the cell station id number to the ps 1. Keep pressing , and until following message will be displayed. Display: function (0-4)? 2. Press . • when the cell station id number is assigned, it is displayed on the bottom line. Display example: cs-id set cs no.(0-7)? 3. Enter t...
8 note • to return to the previous display, press . Deleting the assigned cell station id number on the ps 1. Keep pressing , and until following message will be displayed. Display: function (0-4)? 2. Press . Display example: cs-id clear cs no.(0-7)? (#=all clear) 3. Enter the cell station number (0...
9 unplugging the cable from the cell station after assigning the cell station id number to the ps, unplug the cable from the cell station once. Dip-switch setting after unplugging the cell station once, set the dip-switch as follows. 1. Switch the radio signal test switch from off to on. 2. Set the ...
10 note • to see the signal strength of more than one cell station, the channel for each cell station needs to be set. • up to eight cell stations can be surveyed at the same time. If more than one cell station is in radio signal test mode, each dip-switch channel must be different. Connecting the a...
11 3. To record the result; a) press . • attention!! All directory data will be cleared. • the display will appear as below when the result has not been recorded. • if you want to use a ps as usual, it is required to delete all recorded radio signal test results. Display: all book data is cleared !!...
12 d) press . • the result is recorded. Display: stored note • to return to the previous display, press . • if a channel is set, the results of measurement for the 24 slots on the channel are saved each time. If the same channel is set, the new results override the previous ones. Therefore, a measur...
13 note • to return to the previous display, press . Deleting all recorded radio signal test results 1. Keep pressing , and until following message will be displayed. Display: function (0-4)? 2. Press . Display: all scan data is cleared!! Y=talk n=cancel 3. Press . 4. The display return to the initi...
Printed in the united kingdom psqx2253za copyright: this manual is copyrighted by kyushu matsushita electric co., ltd. (kme). Under the applicable copyright laws, this manual may not be reproduced in any form, in whole or part, without the prior written consent of kme and its licensee. 2000 kyushu m...
