1. DL manuals
  2. Panasonic
  3. Telephone Accessories
  4. KX-TD1232
  5. Program Manual

Panasonic KX-TD1232 Program Manual

Manual is about: Digital Super Hybrid System

Summary of KX-TD1232

  • Page 1

    Kx-td816 kx-td1232 digital super hybrid system d1232 digital super hybrid system panasonic panasonic d816 digital super hybrid system please read this manual before connecting the digital super hybrid system. Panasonic kx-td1232, kxtd1232, kx td1232, td1232, kx-td816, kxtd816, kx td816, td816 www.Vo...

  • Page 2: Introduction

    Introduction 2 programming guide introduction about this programming guide this programming guide is designed to serve as an overall system programming reference for the panasonic digital super hybrid system, kx-td816 / kx-td1232. This manual contains the following sections: section 1, general progr...

  • Page 3: Table of Contents

    Table of contents programming guide 3 table of contents 1 general programming instructions ................................................9 1.1 general programming instructions............................................................................10 1.2 using proprietary telephones ..............

  • Page 4

    Table of contents 4 programming guide [122] ucd overflow........................................................................................................... 93 [123] ucd time table ........................................................................................................ 95 [124...

  • Page 5

    Table of contents programming guide 5 [331] ars modify added number....................................................................................160 [332] extra entry table selection ......................................................................................161 [333] trs entry code ...

  • Page 6

    Table of contents 6 programming guide [461] pri line coding assignment .................................................................................. 244 [462] pri frame sequence assignment............................................................................ 245 [463] pri timer 1 and time...

  • Page 7

    Table of contents programming guide 7 [712] t1 first dial timer (did / tie) ............................................................................... 311 [713] t1 %break ................................................................................................................312 [714] t1...

  • Page 8

    Table of contents 8 programming guide.

  • Page 9: Section

    General programming instructions programming guide 9 section 1 general programming instructions.

  • Page 10: 1.1

    General programming instructions 10 programming guide 1.1 general programming instructions default setting this system has a default factory setting. If any of the programming needs to be changed, you will find the necessary information in the features guide. This makes the system very simple to ins...

  • Page 11: 1.2

    General programming instructions programming guide 11 1.2 using proprietary telephones soft buttons and shift button on the display dpt three soft buttons are provided just below the display on the display of digital proprietary telephones (dpt), kx-t7433, kx-t7436, kx-t7230 and kx-t7235. The functi...

  • Page 12

    General programming instructions 12 programming guide type 5 you can use either the soft buttons or the overlay buttons. (for overlay buttons, refer to "using the overlay" below.) throughout programming you will see instructions such as "press prev". If you use soft buttons, this means press shift, ...

  • Page 13

    General programming instructions programming guide 13 location of controls with the overlay the pictures below show the functions of the buttons of the kx-t7433, kx-t7436, kx-t7230 and kx-t7235 while in programming mode. Kx-t7431 is the same as kx-t7433 except for the soft and shift buttons. Secret ...

  • Page 14

    General programming instructions 14 programming guide viewing the display the display gives you helpful information, such as what you should do now, what you have done, etc. The kx-t7433, kx-t7436, kx-t7230 and the kx-t7235 utilize two information lines for programming. The upper line is called the ...

  • Page 15: 1.3

    General programming instructions programming guide 15 1.3 programming methods advancing to the next stage when " sys-pgm no? " is displayed, you can select one of the following: • to go to program [000], press the next button. • to go to another program, enter the 3-digit program address. Rotation o...

  • Page 16

    General programming instructions 16 programming guide going to another program address after pressing store, you can go to another program with either of the following two methods: a) to go to the next larger program address: press soft 1 (skp+) or volume (down). To go to the next smaller program ad...

  • Page 17: 1.4

    General programming instructions programming guide 17 1.4 entering characters entering characters you can enter characters to store names or messages in the following programs by using the dialing key pad, buttons or the jog dial. [002] system speed dialing name set [004] extension name set [008] ab...

  • Page 18

    General programming instructions 18 programming guide note • the alphabetical characters correspond to the letters shown on the twelve dialing keys on the proprietary telephone. (except symbols) • in combination table a: if your telephone is a kx-t7431, do not use the provided select button. Use the...

  • Page 19

    General programming instructions programming guide 19 please see the following example which shows how to select a desired character. For example, to select the letter "m": select either of the following three methods: 1. Using the shift and soft buttons (for kx-t7433 / kx-t7436 / kx-t7230 / kx-t723...

  • Page 20

    General programming instructions 20 programming guide d) press shift. E) press soft 3 ( i ) f) enter 5 g) press soft 2 ( k ) h) enter 3 i) press soft 2 ( e ) using method (2) * see combination table a. Using method (3) * see combination table b. The display shows: 1. Enter 6. 6 2. Press select. M 3....

  • Page 21

    General programming instructions programming guide 21 or note • to erase all the letters, press clear. • to erase the last letter, press . 2. Rotate jog dial one pulse. M 3. Enter 4. M4 4. Rotate jog dial six pulse. Mi 5. Enter 5. Mi5 6. Rotate jog dial four pulses. Mik 7. Enter 3. Mik3 8. Rotate jo...

  • Page 22: 1.5

    General programming instructions 22 programming guide 1.5 user programming mode user programming mode some programming items are accessible by any display proprietary telephone user in the system. The programming items are listed below: [000] date and time set [001] system speed dialing number set [...

  • Page 23: 1.6

    General programming instructions programming guide 23 1.6 programming example programming example the following programming instructions assume that you have already entered the programming mode and that you will employ method (2) of "going to another program address" in section 1.2 using proprietar...

  • Page 24

    General programming instructions 24 programming guide programming structure program address programming group description [0xx] manager programming these programs may be accessed by the system manager of the customer to meet frequent changes requested by the customer. [1xx] system programming entire...

  • Page 25

    General programming instructions programming guide 25 [5xx] cos programming setting of class of service (cos). [6xx] extension programming setting of extension values. [7xx] t1 programming setting of t1 line. [8xx] resource programming assignment of customer-supplied peripherals connected to the sys...

  • Page 26

    General programming instructions 26 programming guide.

  • Page 27: Section

    General programming programming guide 27 section 2 general programming.

  • Page 28: 2.1

    General programming 28 programming guide 2.1 manager programming [000] date and time set notice it is assumed that you have read section "general programming instructions". Soft button usage is explained in that section, therefore no references will be made to them in the following instructions. The...

  • Page 29

    General programming programming guide 29 8. Press . 9. Keep pressing select until the desired day of the week is displayed. 10. Press store. 11. Press next. Display example: 12:00 pm 24 12. Enter the hour. To change the current entry, press clear and enter the new hour. 13. Press . 14. Enter the min...

  • Page 30: [001]

    General programming 30 programming guide [001] system speed dialing number set description used to program the system speed dial numbers. These numbers are available to all extension users. There are 500 numbers available from 000 to 499. Selection • speed dial number: 000 through 499 • telephone nu...

  • Page 31

    General programming programming guide 31 -to store a pause, press pause. (refer to section "pause insertion, automatic" in the features guide.) -to store a feature number to convert pulse signals to dtmf (dual tone multi-frequency) signals, press the and # keys. (refer to section "pulse to tone conv...

  • Page 32: [002]

    General programming 32 programming guide [002] system speed dialing name set description assigns names to the system speed dial numbers assigned in program [001] system speed dialing number set. Kx-t7235, kx-t7431, kx-t7433, and kx-t7436 telephones can show the stored name during system speed dialin...

  • Page 33

    General programming programming guide 33 features guide references special display features — call directory.

  • Page 34: [003]

    General programming 34 programming guide [003] extension number set description assigns an extension number to each extension. Note this programming should be performed before you connect a panasonic voice processing system (vps) because the vps can create mailboxes automatically based on your exten...

  • Page 35

    General programming programming guide 35 7. Repeat steps 4 through 6. 8. Press end. Conditions • there is a maximum of 32 extension numbers for kx-td816, and 128 extension numbers for kx-td1232. Each extension number can be two, three, or four digits, consisting of 0 through 9. The and # keys cannot...

  • Page 36: [004]

    General programming 36 programming guide [004] extension name set description assigns names to the extension numbers programmed in program [003] extension number set. Selection • jack number: kx-td816 — 01 through 16 (-1 / -2) kx-td1232 — 01 through 64 (-1 / -2) (-1 = first part, -2 = second part) •...

  • Page 37

    General programming programming guide 37 • program [003] extension number set is used to assign extension numbers. • for the kx-td1232, jack numbers 01 through 32 are for the master system and 33 through 64 are for the slave, if available. • for an explanation of jack numbering, see "rotation of jac...

  • Page 38: [005]

    General programming 38 programming guide [005] flexible co button assignment description used to determine the use of the flexible co buttons on proprietary telephones from a centralized telephone. Selection • jack number: kx-td816 — 01 through 16 kx-td1232 — 01 through 64 • button code (plus parame...

  • Page 39

    General programming programming guide 39 default [kx-td816] all jacks — co buttons 1 through 8 = single-co 01 through 08; ring tone type 2 others = not stored [kx-td1232] all jacks — co buttons 1 through 48 = single-co 01 through 48; ring tone type 2 programming 1. Enter 005. Display: 005 flexible c...

  • Page 40

    General programming 40 programming guide • for the kx-td1232, jack numbers 01 through 32 are for the master system and 33 through 64 are for the slave, if available. Jack numbers in the out-of-service system are unacceptable. • the number of the co buttons available depends on the telephone type. (r...

  • Page 41: [006]

    General programming programming guide 41 [006] operator / manager extension assignment description assigns the jack number for a manager and/or operators. The manager extension can perform system programming and manager services. The operators have the ability to perform operator services. Selection...

  • Page 42

    General programming 42 programming guide • if the assigned jack is in extra device port mode, the proprietary telephone jack is treated as the manager / operator extension. • if there is no operator or manager, press clear in step 3. Features guide references manager extension operator.

  • Page 43: [007]

    General programming programming guide 43 [007] dss console port and paired telephone assignment description assigns the jack numbers for the dss console and the paired extension. Selection • dss console number: kx-td816 — 1 through 4 kx-td1232 — 1 through 4 (for master), 5 through 8 (for slave) • ja...

  • Page 44

    General programming 44 programming guide conditions • the jack number for the console and that for the paired extension must be entered together. • multiple dss consoles cannot be assigned to the same dss console jack. • multiple dss consoles can be paired with the same proprietary telephone jack. •...

  • Page 45: [008]

    General programming programming guide 45 [008] absent messages description used to program the absent messages. An absent message, if set by the station user, is displayed on the calling extension's telephone to show the reason for the user's absence. Selection • message number: 1 through 9 • messag...

  • Page 46

    General programming 46 programming guide conditions • there is a maximum of nine messages. Messages 1 through 6 are programmed at the factory but can be changed. Each message has a maximum of 16 characters. • you can enter a maximum of seven "%" characters per message which can be programmed at each...

  • Page 47: [009]

    General programming programming guide 47 [009] quick dial number set description stores up to eight quick dial numbers. Selection • location number: 1 through 8 • desired number: 16 digits (max.) default all location numbers — not stored programming 1. Enter 009. Display: 009 quick dial 2. Press nex...

  • Page 48: [012]

    General programming 48 programming guide [012] isdn extension number set description assigns an extension number to each port which is connected to the isdn unit. Selection • port number: kx-td816 — 01 through 04 kx-td1232 — 01 through 12 • extension number: 2 or 3 digits default all ports — not sto...

  • Page 49

    General programming programming guide 49 • port numbers 01 through 06 are for the master system, and 07 through 12 are for the slave, if available. • an extension number is invalid if the first or second digit does not match with the setting in program [100] flexible numbering, 1st through 16th hund...

  • Page 50: [013]

    General programming 50 programming guide [013] isdn extension name set description assigns names to the isdn extension numbers programmed in program [012] isdn extension number set. Selection • port number: kx-td816 — 01 through 04 kx-td1232 — 01 through 12 • name: 10 characters (max.) default all p...

  • Page 51

    General programming programming guide 51 features guide references none kx-td816 kx-td1232 isdn port no. Kx- td382 kx- td384/ kx- td284 kx- td386 kx- td382 kx- td384/ kx- td284 kx- td386 master slave 1 7 - jack 1 jack 1 - - jack 1 2 8 - jack 2 jack 2 - - jack 2 3 9 jack 1 jack 3 jack 3 - jack 1 jack...

  • Page 52: [014]

    General programming 52 programming guide [014] vm name set description assigns a name for each voice mail port. Selection • voice mail (vm) number: kx-td816 – 01 through 12 kx-td1232 – 01 through 24 • name: 10 characters (max.) default all voice mails — v.Mailxx (xx=01 through 24) programming 1. Ent...

  • Page 53: [017]

    General programming programming guide 53 [017] disa user codes description assigns the direct inward system access (disa) user codes and a class of service (cos) to each code. The cos of the code determines the toll restriction level of the disa caller. This program is available for the kx-td1232 on...

  • Page 54

    General programming 54 programming guide 5. Press to program cos. 6. Enter a cos number. To change the current entry, enter the new cos number. 7. Press store. 8. To program another user code, press next or prev, or select and the desired disa user code number. 9. Repeat steps 4 through 8. 10. Press...

  • Page 55: 2.2

    General programming programming guide 55 2.2 system programming [100] flexible numbering description assigns the leading digits of extension numbers and feature numbers for system features. Feature number list number feature default 01 1st hundred extension block 1 02 2nd hundred extension block 2 0...

  • Page 56

    General programming 56 programming guide 38 external feature access 6 39 station program clear 790 40 message waiting 70 41 *1 outgoing message 36 42 call forwarding / do not disturb 710 43 call pickup deny 720 44 data line security 730 45 call waiting / ohca / whisper ohca 731 46 executive busy ove...

  • Page 57

    General programming programming guide 57 selection • selection number: 01 through 93 (see "feature number list" for the corresponding features.) • feature number: 1 or 2 digits (for selection numbers 01 – 16, 74 – 89); 1 through 3 digits (for selection numbers 17 – 73 and 90 – 93) default see "featu...

  • Page 58

    General programming 58 programming guide 2. Press next. Display: select no? 3. Enter a selection number. To enter selection number 01, you can also press next. Display example: 01. 1-ext bl:1 4. Enter the feature number. To delete the feature number, press clear. To change the current entry, press c...

  • Page 59

    General programming programming guide 59 features guide references flexible numbering.

  • Page 60: [101]

    General programming 60 programming guide [101] day / night service switching mode description this program is used to determine if night mode is set automatically or manually. Selection manual / auto (automatic) default manual programming 1. Enter 101. Display: 101 day / nt auto 2. Press next. Displ...

  • Page 61: [102]

    General programming programming guide 61 [102] day / night service starting time description sets the starting time on a day of the week basis, when automatic day / night switching is programmed in program [101] day / night service switching mode. Selection • day of the week selection number: 1 (sun...

  • Page 62

    General programming 62 programming guide 10. To program another day / night mode or day of the week, press next or prev, or select and the day of the week selection number. 11. Repeat steps 4 through 10. 12. Press end. Conditions • to select the desired day, you may keep pressing next in step 3. To ...

  • Page 63: [103]

    General programming programming guide 63 [103] automatic access outside line assignment description assigns the sequence in which outside line groups will be accessed when in automatic line access mode. When a user dials the feature number for automatic line access (default=9) or presses the loop-co...

  • Page 64: [105]

    General programming 64 programming guide [105] account codes description assigns the account codes for account code entry, verified — all calls and verified — toll restriction override modes. If verified — all calls is assigned in program [508] account code entry mode, an account code is required to...

  • Page 65

    General programming programming guide 65 features guide references account code entry toll restriction override by account code entry.

  • Page 66: [106]

    General programming 66 programming guide [106] station hunting type description used to enable or disable hunting and set the station hunting type for each extension group. There are six station hunting types available: circular, terminating, voice mail (vm), automated attendant (aa), ring group and...

  • Page 67

    General programming programming guide 67 conditions • program [602] extension group assignment is used to assign the extension group members. • the system supports a maximum of six jacks (12 jacks during system connection *1 ) for connection to a voice processing system as vm or aa ports. • to assig...

  • Page 68: [107]

    General programming 68 programming guide [107] system password description assigns the password required for entering system programming mode and for maintenance from a personal computer. Warning the dealer should take care with the system password: a) please thoroughly instruct the importance of th...

  • Page 69

    General programming programming guide 69 • if less than four digits are entered, they are not stored. • you cannot leave the entry empty. Features guide references system programming and diagnosis with personal computer system programming with proprietary telephone.

  • Page 70: [108]

    General programming 70 programming guide [108] automatic hold by co / dss button description enables or disables automatically holding an outside call when a dss (direct station selection) button on the dss console or proprietary telephone, or a co button on a proprietary telephone is pressed. Throu...

  • Page 71: [109]

    General programming programming guide 71 [109] expansion unit type description assigns the type of expansion units to be used in the system. This allows the system to identify the unit in each expansion unit location. Selection kx-td816 • areas 1; 2 = c / s2 / s4 / s6 / bd / e kx-td1232 • master / s...

  • Page 72

    General programming 72 programming guide display example: master:c ;e1;e2 3. Keep pressing select until the desired selection in area 1 is displayed. 4. Press to program another area, if required. 5. Keep pressing select until the desired selection in the area is displayed. 6. Repeat steps 4 and 5 u...

  • Page 73: [110]

    General programming programming guide 73 [110] caller id code set description sets the identification code of the calling party (caller id code) to utilize a caller id service provided by a specific central office (co). If an id code transmitted from the co is found in the caller id code table, the ...

  • Page 74

    General programming 74 programming guide • program [406] caller id assignment is used to enable the caller id service on an outside line basis. Features guide references caller id.

  • Page 75: [111]

    General programming programming guide 75 [111] caller id name set description with caller id service, the calling party is displayed either by its id code or by its name. If the name display is required, use this program to give a name to a caller id code stored in program [110] caller id code set. ...

  • Page 76

    General programming 76 programming guide features guide references caller id.

  • Page 77: [112]

    General programming programming guide 77 [112] network type assignment description assigns the type of isdn network. Selection ni1 (national isdn1) / att custom default ni1 programming 1. Enter 112. Display: 112 switch type 2. Press next. Display example: ni1 3. Keep pressing select until the desire...

  • Page 78: [113]

    General programming 78 programming guide [113] vm status dtmf set description sets the dtmf (dual tone multi-frequency) signals transmitted to your voice processing system (vps) to inform the vps of the vps ports states quickly: the following signals are sent to the vps with the assigned dtmf signal...

  • Page 79

    General programming programming guide 79 display example: rbt :1 3. Enter a dtmf signal number. To delete the current entry, press clear. To change the current entry, press clear and enter the new number. 4. Press store. 5. To program another selection, keep pressing next or prev until the desired s...

  • Page 80: [114]

    General programming 80 programming guide [114] vm command dtmf set description sets the dtmf (dual tone multi-frequency) command signals transmitted to your voice processing system (vps). There are four commands available: leave message; get message; automated attendant service; voice mail service. ...

  • Page 81

    General programming programming guide 81 programming 1. Enter 114. Display: 114 vm dtmf cmd 2. Press next to program the lv-msg command. To program another command, keep pressing next until the desired command is displayed. Display example: lv-msg:h 3. Enter a dtmf signal number. To delete the curre...

  • Page 82: [115]

    General programming 82 programming guide [115] adjust time description used to adjust the time for checking the normality of system data. Every day at the programmed time, the data adjustment is performed. Selection • hour: 1 through 12 • minute: 00 through 59 • am / pm default 1:00 am programming 1...

  • Page 83: [116]

    General programming programming guide 83 [116] rom version display description confirms the version of rom of the system. Display example: selection system number: kx-td816 — 0 kx-td1232 —0 (master) / 1 (slave) default not applicable. Programming 1. Enter 116. Display: 116 rom version 2. Press next....

  • Page 84: [117]

    General programming 84 programming guide [117] voice mail number assignment description assigns the jack number corresponding to the voice mail port for data transmission to the voice processing system. The voice mail port is expandable to six ports (12 ports during system connection for kx-td1232)....

  • Page 85

    General programming programming guide 85 kx-td1232 1. Enter 117. Display: 117 vms port asn 2. Press next to program the master system. Display example: mast1:# # # 3. Enter a jack number. To delete the current entry, press clear. To change the current entry, press clear and enter the new jack number...

  • Page 86: [118]

    General programming 86 programming guide [118] voice mail extension number assignment description assigns the extension number for the voice mail number. These numbers can be used the same way extension numbers are used for station access. Selection • voice mail number (vm): kx-td816 — 01 through 12...

  • Page 87

    General programming programming guide 87 conditions • for the kx-td1232, vm-01 through vm-12 are for the master system and vm-13 through vm-24 are for the slave system, if available. • you cannot leave an entry empty. • double entry and incompatible entry for these numbers are invalid. Valid entry e...

  • Page 88: [119]

    General programming 88 programming guide [119] voice mail extension group assignment description assigns each voice mail number to a voice mail extension group number. Selection • voice mail number (vm): kx-td816 — 01 through 12, kx-td1232 — 01 through 24, ( =all voice mail numbers) • voice mail ext...

  • Page 89

    General programming programming guide 89 "-1" of yy-1 means the first part of the jack number in digital line. "yy-2" means the second part of the jack number in digital line. • to assign all voice mail numbers to one selection, press the key in step 3. In this case, the display shows the contents p...

  • Page 90: [120]

    General programming 90 programming guide [120] user password description assigns the password required for entering the user programming mode. In the user programming mode, any display digital proprietary telephone user in the system can set the following programs: [000] date and time set [001] syst...

  • Page 91

    General programming programming guide 91 features guide references user programming (manager programming).

  • Page 92: [121]

    General programming 92 programming guide [121] walking cos password description assigns the password required for walking cos. Selection password: 4 through 7 digits default 1234 programming 1. Enter 121. Display: 121 cos password 2. Press next. Display example: password:1234 3. Enter a password. To...

  • Page 93: [122]

    General programming programming guide 93 [122] ucd overflow description assigns the destination where the call is transferred to when all extensions in the uniform call distribution (ucd) group are busy. The time table number of the overflow extension must also be assigned. Selection • ucd group num...

  • Page 94

    General programming 94 programming guide features guide references uniform call distribution (ucd).

  • Page 95: [123]

    General programming programming guide 95 [123] ucd time table description assigns the queuing sequence in the uniform call distribution (ucd) time table. The queuing sequences are as follows: *1 s1: sends disa (direct inward system access) outgoing message 1. *1 s2: sends disa outgoing message 2. *1...

  • Page 96

    General programming 96 programming guide 7. Press store. 8. Press end. Conditions • "sx" can be assigned to a space other than the first only when another "sx" is assigned in the first space. • an assignment after "tr", "rt" or "blank" is not available. Features guide references ring group uniform c...

  • Page 97: [124]

    General programming programming guide 97 [124] phantom extension number assignment description assigns the phantom extension numbers. Each number will be assigned to a flexible co or dss (direct station selection) button and used as a phantom extension button. Selection • location number: 001 throug...

  • Page 98

    General programming 98 programming guide [003] extension number set, [012] isdn extension number set, [118] voice mail extension number assignment and [813] floating number assignment. Features guide references phantom extension.

  • Page 99: [125]

    General programming programming guide 99 [125] area code assignment description assigns up to ten area codes which are necessary when using the caller id feature. By assigning your area code, the system records the caller's phone number modified by programs [126] caller id modification for local cal...

  • Page 100

    General programming 100 programming guide call log, incoming.

  • Page 101: [126]

    General programming programming guide 101 [126] caller id modification for local call description assigns removed digits from the received caller's number of a local call, and adds number to make the final number which serves as the caller id number. The system records the modified caller's number t...

  • Page 102

    General programming 102 programming guide • there are ten location numbers for modified numbers, which corresponds to those in program [125] area code assignment. Features guide references caller id call log, incoming.

  • Page 103: [127]

    General programming programming guide 103 [127] caller id modification for long distance call description assigns removed digits from the received caller's number of a long distance call, and adds number to make the final number which serves as the caller id number. The system records the modified c...

  • Page 104: [128]

    General programming 104 programming guide [128] pbx code description assigns the pbx code as your location number if the "pbx code method" is employed for tie line network calling. Selection • pbx code: 1 to 3 digits default not stored programming 1. Enter 128. Display: 128 pbx code 2. Press next. D...

  • Page 105: [130]

    General programming programming guide 105 [130] message waiting control description assigns the data ports which communicate with the message waiting lamp adaptor (kx- td194). Selection • unit (td194) number: kx-td816 — 1 kx-td1232 — 1 or 2 (for master), 4 or 5 (for slave) • jack number: kx-td816 — ...

  • Page 106

    General programming 106 programming guide if the unit is connected to a port which is not assigned as the data port, a clicking sound may be heard from the unit. Please make sure that the unit is connected to the assigned port. • when the data port is assigned properly and the unit is connected to t...

  • Page 107: [131]

    General programming programming guide 107 [131] message waiting lamp assignment description assigns the message waiting light pattern. Selection • message waiting light pattern number: 1 through 12 default 1 programming 1. Enter 131. Display: 131 mw lamp 2. Press next. Display: mw lamp no:1 3. Enter...

  • Page 108

    General programming 108 programming guide • the available message waiting light patterns are as follows. 1.25 s 500 ms 250 ms 5 s 10± α s 500 ms 500 ms 250 ms 250 ms 250 ms pattern 01 pattern 02 pattern 03 pattern 04 pattern 05 pattern 06 500 ms 500 ms 250 ms 20± α s 5 s 500 ms 1.25 s 1.25 s 1.25 s ...

  • Page 109

    General programming programming guide 109 features guide references message waiting.

  • Page 110: [132]

    General programming 110 programming guide [132] message waiting port set description assigns which single line telephone port is connected to the kx-td194 port. Selection • unit (td194) number: kx-td816 — 1 kx-td1232 — 1 or 2 (for master), 4 or 5 (for slave) • message waiting port number: 01 through...

  • Page 111

    General programming programming guide 111 11. Repeat steps 5 through 9 12. Press end. Conditions • to program another unit, start from step 1. • for the kx-td1232, the unit numbers 1 and 2 are for the master system and 4 and 5 are for the slave system, and jack numbers 01 through 32 are for master s...

  • Page 112: [133]

    General programming 112 programming guide [133] caller id extension assignment description assigns which kx-td171 port receives caller id information. Selection • unit (td171) number: kx-td816 — 1 kx-td1232 — 1 through 4 • port number: 1 or 2 default not stored programming 1. Enter 133. Display: 133...

  • Page 113

    General programming programming guide 113 call information transferred by the call transfer, screened — to extension feature cannot be sent. However, when a call is transferred by the call transfer, unscreened feature, the information can be sent to the destination extension. • when several incoming...

  • Page 114: [134]

    General programming 114 programming guide [134] hotel application description assigns whether the hotel application is enabled or disabled. Selection on / off default off programming 1. Enter 134. Display: 134 hotel on / off 2. Press next. Display example: hotel:off 3. Keep pressing select until the...

  • Page 115: [135]

    General programming programming guide 115 [135] did number conversion selection description selects whether the direct inward dialing (did) number is allocated as an extension number or is converted using the transfer table. Selection • ext number / transfer table default transfer table programming ...

  • Page 116: [136]

    General programming 116 programming guide [136] did number assignment description assigns the direct inward dialing (did) number which is converted from the did subscriber number using the programs [433] did / tie subscriber number removed digit and [434] did / tie added number. If the converted num...

  • Page 117

    General programming programming guide 117 • to use this program, "transfer table" must be selected beforehand in program [135] did number conversion selection. Features guide references direct inward dialing (did).

  • Page 118: [137-138]

    General programming 118 programming guide [137-138] did extension —— day / night description determines the extension which receive a direct inward dialing (did) call in both the day and night modes. Selection • location number: 001 through 200 • extension number: 2 to 4 digits / 0 (operator) defaul...

  • Page 119

    General programming programming guide 119 • to use this program, "transfer table" must be selected first in program [135] did number conversion selection, and then the did number must be assigned in program [136] did number assignment. Features guide references direct inward dialing (did) night serv...

  • Page 120: [139]

    General programming 120 programming guide [139] did extension name set description assigns names to the did extension assigned in program [136] did number assignment. Selection • location number: 001 through 200 • extension number: 10 characters (max.) default all locations — not stored programming ...

  • Page 121: [148]

    General programming programming guide 121 [148] off-hook monitor description enables or disables to perform the off-hook monitor. Selection • enable / disable default enable programming 1. Enter 148. Display: 148 hook monitor 2. Press next. Display example: monitor:enable 3. Keep pressing select unt...

  • Page 122: [150]

    General programming 122 programming guide [150] lunch service starting / ending time description sets the lunch starting and ending time for each day of the week. Selection • day of the week selection number: 1 (sunday) / 2 (monday) / 3 (tuesday) / 4 (wednesday) / 5 (thursday) / 6 (friday) / 7 (satu...

  • Page 123

    General programming programming guide 123 conditions • this programming can only be used if "auto (automatic)" is selected in program [101] day / night service switching mode. • lunch service ends at the assigned time. For example: if lunch service is 11:30 am – 1:00 pm, day mode starts at 1:01 pm. ...

  • Page 124: [151]

    General programming 124 programming guide [151] break service starting / ending time description sets the break starting and ending time for each day of the week. Selection • day of the week selection number: 1 (sunday) / 2 (monday) / 3 (tuesday) / 4 (wednesday) / 5 (thursday) / 6 (friday) / 7 (satu...

  • Page 125

    General programming programming guide 125 conditions • this feature can only be used if "auto (automatic)" is selected in program [101] day / night service switching mode. • break service ends at the assigned time. For example: if break service is 3:00 – 4:00 pm, day mode starts at 4:01 pm. If break...

  • Page 126: 2.3

    General programming 126 programming guide 2.3 timer programming [200] hold recall time description assigns the length of the hold recall timer. This timer is used to alert an extension that a call has been held for an extended period of time. Selection time (seconds): 0 through 240 (0=hold recall di...

  • Page 127: [201]

    General programming programming guide 127 [201] transfer recall time description sets the number of rings before transfer recall occurs. If a transferred call is not answered after the programmed number of rings, the call returns to the original caller. Selection number of rings: 0 through 48 (0=tra...

  • Page 128: [202]

    General programming 128 programming guide [202] call forwarding — no answer time description sets the number of rings for call forwarding — no answer feature. If a call is not answered after the programmed number of rings, the call is forwarded to the destination. Selection number of rings: 1 throug...

  • Page 129: [203]

    General programming programming guide 129 [203] intercept time description sets the number of rings for intercept routing — no answer (irna) feature. If a call is not answered after the programmed number of rings, the call is redirected to the programmed station. Selection number of rings: 3 through...

  • Page 130: [204]

    General programming 130 programming guide [204] pickup dial waiting time description sets the number of seconds for pickup dialing. If the telephone user lifts the handset, the programmed party is called when the time expires. Selection time (seconds): 1 through 5 default 1 sec programming 1. Enter ...

  • Page 131: [205]

    General programming programming guide 131 [205] extension-to-outside line call duration time description sets the maximum time allowed for a conversation with an outside party. If an outside call is originated or answered by a programmed extension user and the timer expires, the call is disconnected...

  • Page 132: [206]

    General programming 132 programming guide [206] outside-to-outside line call duration time description sets the maximum time allowed for a conversation between two outside parties. When the timer expires, the outside-to-outside line call is disconnected. Selection time (minutes): 1 through 64 defaul...

  • Page 133: [207]

    General programming programming guide 133 [207] first digit time description sets the maximum time allowed between the start of an outside dial tone and the first digit dialed on an outgoing outside call. If an extension user fails to dial any digits during this time, the dtmf (dual tone multi-frequ...

  • Page 134: [208]

    General programming 134 programming guide [208] inter digit time description assigns the maximum time allowed between digits on an outgoing toll call. If an extension user fails to dial any digits during this time, the dtmf (dual tone multi-frequency) receiver is released. This timer applies until t...

  • Page 135: [211]

    General programming programming guide 135 [211] dial start time description sets the number of milliseconds the system waits before dialing after an outside line is seized. Selection time (milliseconds): 0 through 40 ( 100 is the actual time) default 500 msec programming 1. Enter 211. Display: 211 d...

  • Page 136: [212]

    General programming 136 programming guide [212] call duration count start time description sets the number of seconds the system waits between the end of dialing and the start of the station message detail recording (smdr) timer for outgoing toll calls. When the system has sent out all the digits to...

  • Page 137: [213]

    General programming programming guide 137 [213] disa delayed answer time description assigns the number of rings between a call received and the answer by the direct inward system access (disa) feature. This programming is available for the kx-td1232 only. Selection number of rings: 0 through 6 defa...

  • Page 138: [214]

    General programming 138 programming guide [214] disa prolong time description sets the maximum allowable prolonged time for an outside-to-outside line call via the direct inward system access (disa) feature. An outside-to-outside line call is initially limited by the "outside-to-outside line call du...

  • Page 139: [215]

    General programming programming guide 139 [215] outgoing message time description sets the maximum allowable recording time for outgoing messages (ogm). This programming is available for the kx-td1232 only. Selection time (seconds): 0 / 16 / 32 / 64 (0=no recording) default 32, 0, 32, 0 (for ogm 1 t...

  • Page 140

    General programming 140 programming guide features guide references direct inward system access (disa) outgoing message (ogm) timed reminder uniform call distribution (ucd).

  • Page 141: [216]

    General programming programming guide 141 [216] message waiting ring interval time description sets the message waiting ring interval time for a single line telephone. Selection time (minutes): 0 through 64 default 0 min (no ring) programming 1. Enter 216. Display: 216 mw ring time 2. Press next. Di...

  • Page 142: [217]

    General programming 142 programming guide [217] timed reminder alarm ring time description sets the number of seconds the timed reminder alarm rings. Selection time (seconds): 30 through 240 default 30 sec programming 1. Enter 217. Display: 217 timed remind 2. Press next. Display example: reminder: ...

  • Page 143: [218]

    General programming programming guide 143 [218] disa aa wait time description sets the number of seconds the system waits for a second digit entry. If the timer expires, the system assumes that the first digit is a disa (direct inward system access) built-in auto attendant number if assigned in prog...

  • Page 144: [219]

    General programming 144 programming guide [219] call park recall time description sets the number of rings before call park recall occurs. Call park recall is used to alert an extension that a call has been parked for an extended period of time. Selection number of rings: 0 through 48 (0=call park r...

  • Page 145: [220]

    General programming programming guide 145 [220] tie first / inter digit time description assigns the maximum time allowed between the start of the dial tone and the first digit dialed (first digit time), and between digits (inter digit time) on a tie call. If an extension user fails to dial any digi...

  • Page 146: 2.4

    General programming 146 programming guide 2.4 trs / ars programming [300] trs override for system speed dialing description allows you to enable toll restriction override for system speed dial numbers. If this is enabled, all extension users can make system speed dialing calls with no restriction. S...

  • Page 147: [301-305]

    General programming programming guide 147 [301-305] trs denied code entry for levels 2 through 6 description these allow you to specify the numbers which are toll-restricted for each toll restriction level as follows: program [301]: restricts levels 2 through 6 program [302]: restricts levels 3 thro...

  • Page 148

    General programming 148 programming guide conditions • there is a maximum of 20 toll call numbers which can be restricted for each program. Each number has a maximum of ten digits, consisting of 0 through 9, and . The character " " can be used as a wild card character. • programs [306-310] trs excep...

  • Page 149: [306-310]

    General programming programming guide 149 [306-310] trs excepted code entry for levels 2 through 6 description these allow you to assign numbers which are exceptions to the toll restriction specified in programs [301] through [305] as follows: program [306]: applies to level 2 program [307]: applies...

  • Page 150

    General programming 150 programming guide conditions there is a maximum of five numbers for each program. Each number has a maximum of ten digits, consisting of 0 through 9, and . The character " " can be used as a wild card character. Features guide references toll restriction.

  • Page 151: [311]

    General programming programming guide 151 [311] special carrier access codes description assigns special carrier numbers. This allows the system to recognize the user-dialed special carrier number in order to insert the required pause and apply toll restriction. Selection • location number: 01 throu...

  • Page 152: [312]

    General programming 152 programming guide [312] ars mode description allows you to turn on or off the automatic route selection (ars) mode. Ars, if enabled, selects the least expensive route to be used for an outside call. Selection on / off default off programming 1. Enter 312. Display: 312 ars mod...

  • Page 153: [313]

    General programming programming guide 153 [313] ars time description assigns times for the four automatic route selection (ars) time schedules. It is possible to split a day into four time zones (maximum) so that the least expensive line is selected for that time. According to the service hours and ...

  • Page 154

    General programming 154 programming guide 9. Repeat steps 4 through 8. 10. Press end. Conditions • enter a starting time for each time schedule. Select "disable" for idle schedules. • you cannot leave an entry empty. • to assign all days of the week, press the key in step 3. In this case, the displa...

  • Page 155: [314-321]

    General programming programming guide 155 [314-321] ars leading digit entry for plans 1 through 8 description by entering numbers into each leading digit plan (programs below) you are starting the process to determine which outside line group will be used to route the call. These eight plans are use...

  • Page 156

    General programming 156 programming guide conditions each number has a maximum of ten digits, consisting of 0 through 9, and . The character " " can be used as a wild card character (i.E., "do not care" digit). The system scans all the ars leading digit plans simultaneously from left to right. The s...

  • Page 157: [322-329]

    General programming programming guide 157 [322-329] ars routing plans 1 through 8 description assigns the outside line group and modification plan to be used for each route plan and time schedule. Selection • time schedule: a / b / c / d • outside line group number: 1 through 8 • modification table ...

  • Page 158

    General programming 158 programming guide 11. Press end. Conditions • up to three outside line groups and modification plans can be assigned for each time schedule. The outside line group number and modification table number must be entered together. The highest priority outside line group number an...

  • Page 159: [330]

    General programming programming guide 159 [330] ars modify removed digit description determines how the dialed number should be modified before transmitting to the central office. You can delete the digits from the beginning of the dialed number. Selection • modification table number: 1 through 8 • ...

  • Page 160: [331]

    General programming 160 programming guide [331] ars modify added number description determines how the dialed number should be modified before transmitting to the central office. Assigned numbers are added to the beginning of the dialed number. Selection • modification table number: 1 through 8 • nu...

  • Page 161: [332]

    General programming programming guide 161 [332] extra entry table selection description selects the code table which enables an extra 400 entries within denied or except code table. Selection • deny / except • level number: 2 through 6 default except - 2 programming 1. Enter 332. Display: 332 trs ex...

  • Page 162: [333]

    General programming 162 programming guide [333] trs entry code assignment for extra table description this program allows you to specify the numbers for extra denied or excepted code table for expansion. Selection • location number: 001 through 400 • toll call number: 10 digits (max.) default all lo...

  • Page 163: [334]

    General programming programming guide 163 [334] emergency dial number set description stores up to ten emergency call numbers. Emergency numbers are not subject to toll restriction, account code — verified mode and electronic station lockout. Selection • location number: 01 through 10 • emergency nu...

  • Page 164: [340]

    General programming 164 programming guide [340] tie line routing table description the tie line routing table can be programmed. This table is referenced by the system to identify the outside (co) line route, when an extension user makes a tie call. A routing pattern appropriate for each call is dec...

  • Page 165

    General programming programming guide 165 conditions each tie line access code has a maximum of three digits, consisting of 0 through 9 and . The character " " can be used as a wild card character. Program [341] tie modify removed / added digit is used to modify the tie line access code. Features gu...

  • Page 166: [341]

    General programming 166 programming guide [341] tie modify removed / added digit description assigns the removed and added digits of the tie call received digits. Digits are removed and added from the beginning of the dialed digits. Selection • location number: 01 through 32 • number of digits to be...

  • Page 167

    General programming programming guide 167 features guide references t1 line tie line service.

  • Page 168: 2.5

    General programming 168 programming guide 2.5 outside line programming [400] outside line connection assignment description used to identify the outside lines which are connected to the system(s). This prevents users from originating a call to a line which is not connected. Selection • outside line ...

  • Page 169

    General programming programming guide 169 outside lines 25 through 47 become available for the pri isdn line when the kx-td290 expansion unit is installed in the master system of the kx-td1232. • to assign all outside lines to one selection, press the key in step 3. In this case, the display shows t...

  • Page 170: [401]

    General programming 170 programming guide [401] outside line group assignment description each outside line must be assigned to an outside line group. This program defines the outside line group assignment for each outside line. For example, if there are multiple telephone service companies availabl...

  • Page 171

    General programming programming guide 171 7. Repeat steps 4 through 6. 8. Press end. Conditions • for the kx-td1232, outside lines 01 through 12 are for the master system and outside lines 13 through 24 are for the slave, if available. • outside lines 25 through 48 become available for the t1 line w...

  • Page 172: [402]

    General programming 172 programming guide [402] dial mode selection description each outside line can be programmed for dtmf (dual tone multi-frequency), pulse (rotary) or call blocking. This program assigns your choice to each line. Dtmf: the dialing signals from an extension, either tone or pulse,...

  • Page 173

    General programming programming guide 173 conditions • for the kx-td1232, outside lines 01 through 12 are for the master system and outside lines 13 through 24 are for the slave, if available. • to assign all lines to one selection, press the key in step 3. In this case, the display shows the conten...

  • Page 174: [403]

    General programming 174 programming guide [403] pulse speed selection description an outside line set for pulse or call blocking mode in program [402] dial mode selection can have two pulse rates, 10 pps (low) and 20 pps (high). This program sets the pulse speed for each outside line set to pulse or...

  • Page 175

    General programming programming guide 175 • program [990] system additional information, area 02 - bit 7 and 12, 11 are used to select a pulse break ratio and inter-digit pause, if needed. Features guide references dial type selection.

  • Page 176: [404]

    General programming 176 programming guide [404] dtmf time description an outside line set to dtmf (dual tone multi-frequency) mode in program [402] dial mode selection can have two settings. This program sets the duration of the dtmf signals sent to an outside line to dtmf mode. Selection • outside ...

  • Page 177

    General programming programming guide 177 features guide references dial type selection.

  • Page 178: [405]

    General programming 178 programming guide [405] cpc signal detection incoming set description assigns the expected minimum duration of the calling party control (cpc) signal on incoming outside calls. If this is programmed, the system disconnects the line when the cpc signal is detected. Selection •...

  • Page 179

    General programming programming guide 179 • program [415] cpc signal detection outgoing set is used to program cpc signal detection for outgoing outside calls. Features guide references calling party control (cpc) signal detection direct inward system access (disa).

  • Page 180: [406]

    General programming 180 programming guide [406] caller id assignment description enables the caller id feature for the outside lines to which a caller id service is offered by a central office by contract. Selection • outside line (co) number: kx-td816 —01 through 08, kx-td1232 — 01 through 24, ( =a...

  • Page 181

    General programming programming guide 181 features guide references caller id.

  • Page 182: [407-408]

    General programming 182 programming guide [407-408] dil 1:1 extension —— day / night description the direct in lines (dil) 1:1 feature allows incoming outside calls to be directed to a specific extension. When an outside line is assigned as dil 1:1, it is necessary to assign the destination. These p...

  • Page 183

    General programming programming guide 183 • to assign all outside lines to one selection, press the key in step 3. In this case, the display shows the contents programmed for outside line 01. • you set the extension numbers in program [003] extension number set, isdn extension numbers in program [01...

  • Page 184: [409-410]

    General programming 184 programming guide [409-410] intercept extension —— day / night description intercept routing provides an automatic re-direction of calls which cannot or have not been answered (irna: intercept routing — no answer). These programs set the destination in both day and night mode...

  • Page 185

    General programming programming guide 185 extension group(s) in program [813] floating number assignment. You cannot assign the floating number of the modem. • to assign all outside line groups to one selection, press the key in step 3. In this case, the display shows the contents programmed for out...

  • Page 186: [411]

    General programming 186 programming guide [411] host pbx access codes description assigns host pbx or centrex access codes. If the system is installed behind a host pbx or a centrex system, an access code is required to make an outside / centrex call or to access centrex features. Up to four codes c...

  • Page 187

    General programming programming guide 187 conditions • this program is only required if a host pbx or centrex line is connected to the system. Program [401] outside line group assignment is used to assign the line to an outside line group. • there is a maximum of four access codes per outside line g...

  • Page 188: [412]

    General programming 188 programming guide [412] pause time description assigns the length of the pause time. The programmed pause time is automatically inserted after a line access code or a host pbx access code programmed in program [411] host pbx access codes or manually inserted if the pause butt...

  • Page 189

    General programming programming guide 189 features guide references host pbx access pause insertion, automatic.

  • Page 190: [413]

    General programming 190 programming guide [413] flash time description assigns the length of the flash time. If your system is installed behind a host pbx or centrex line, external feature access (efa) is necessary to obtain their services. To enable it, select a required hooking signal sending time...

  • Page 191

    General programming programming guide 191 • program [401] outside line group assignment is used to assign each outside line to an outside line group. Features guide references external feature access.

  • Page 192: [414]

    General programming 192 programming guide [414] disconnect time description determines the amount of time between successive accesses to the same outside line. Selection • outside line group (trg) number: 1 through 8, ( =all outside line groups) • time (seconds): 1.5 / 4.0 default all outside line g...

  • Page 193

    General programming programming guide 193 features guide references flash.

  • Page 194: [415]

    General programming 194 programming guide [415] cpc signal detection outgoing set description enables or disables calling party control (cpc) signal detection during the time between the originated outside call and the established outside call. If this is enabled, the system disconnects the line wit...

  • Page 195

    General programming programming guide 195 • for the kx-td1232, outside lines 01 through 12 are for the master system and outside lines 13 through 24 are for the slave, if available. • to assign all outside lines to one selection, press the key in step 3. In this case, the display shows the contents ...

  • Page 196: [416]

    General programming 196 programming guide [416] reverse circuit assignment description enables or disables reverse circuit detection. Selection • outside line (co) number: kx-td816 — 01 through 08, kx-td1232 — 01 through 24, ( =all outside lines) • regular (no detection) / reverse (detection) defaul...

  • Page 197: [417]

    General programming programming guide 197 [417] outside line name assignment description assigns names of the company or customer to each outside line so that the operator or extension user can find the destination which the caller is trying to reach before answering. If caller id is assigned, each ...

  • Page 198

    General programming 198 programming guide • outside lines 25 through 48 become available for the t1 line when the kx-td187 expansion unit is installed in the master system of the kx-td1232. Outside lines 25 through 47 become available for the pri isdn line when the kx-td290 expansion unit is install...

  • Page 199: [418]

    General programming programming guide 199 [418] outside line number assignment for pri clip description assigns your isdn network telephone number. Your isdn network telephone number is sent to the called party with the clip (calling line identification presentation) feature offered by the pri isdn ...

  • Page 200

    General programming 200 programming guide • your telephone number will be informed to the called party if the outgoing clir feature is disabled for the isdn line in program [419] isdn outgoing clir service assignment. Features guide references calling line identification presentation (clip) calling ...

  • Page 201: [419]

    General programming programming guide 201 [419] isdn outgoing clir service assignment description assigns whether isdn clir (calling line identification restriction) service is enabled or disabled for outgoing outside calls. If disabled, the subscriber's number of your system is sent to the called p...

  • Page 202

    General programming 202 programming guide • the outside line number available for the pri isdn line is referred to program [721] t1 / pri reference co. Features guide references calling line identification restriction (clir).

  • Page 203: [420]

    General programming programming guide 203 [420] isdn ring service assignment description assigns the isdn ring service for each outside line. If "isdn" is selected, the extensions which are assigned in programs [137-138] did extension —— day / night for isdn (pri) and [455-456] extension ringing ass...

  • Page 204

    General programming 204 programming guide • to assign all outside lines to one selection, press the key in step 3. In this case, the display shows the contents programmed for outside line 01. • lunch / break mode will only work when "regular" is assigned in this program. • the outside line number av...

  • Page 205: [423]

    General programming programming guide 205 [423] isdn port type description assigns the type of each port to either outside line or extension line on an isdn port basis. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 through 12, ( =all ports) • co (outside line)/ exte...

  • Page 206

    General programming 206 programming guide • to assign all ports to one selection, press the key in step 3. In this case, the display shows the contents programmed for port 01. • after this assignment, you should reset the system so that this assignment is activated. Features guide references none kx...

  • Page 207: [424]

    General programming programming guide 207 [424] isdn layer 1 active mode description assigns the active mode of layer 1 on an isdn port basis. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 through 12, ( =all ports) • permanent / call default all ports — permanent pr...

  • Page 208

    General programming 208 programming guide features guide references none.

  • Page 209: [425]

    General programming programming guide 209 [425] isdn configuration description assigns the configuration on an isdn port basis. This program is available for isdn extensions only. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 through 12, ( =all ports) • point (point...

  • Page 210

    General programming 210 programming guide • after this assignment, you should reset the system so that this assignment is activated. Features guide references none.

  • Page 211: [426]

    General programming programming guide 211 [426] isdn data link mode description assigns the data link mode on an isdn port basis. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 through 12, ( =all ports) • permanent / call default all ports — permanent programming 1. ...

  • Page 212

    General programming 212 programming guide features guide references none.

  • Page 213: [427]

    General programming programming guide 213 [427] isdn tei mode description assigns the terminal endpoint identifier (tei) mode on an isdn port basis. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 through 12, ( =all ports) • fix 0 through 63 / automatic default all po...

  • Page 214

    General programming 214 programming guide • to assign all ports to one selection, press the key in step 3. In this case, the display shows the contents programmed for port 01. • after this assignment, you should reset the system so that this assignment is activated. Features guide references none.

  • Page 215: [428]

    General programming programming guide 215 [428] isdn extension multiple directory number description selects whether the multiple directory number is allocated to each terminal equipment (e.G., isdn telephone) on the isdn bus or not on an isdn port basis. Selection • port number: kx-td816 — 01 throu...

  • Page 216

    General programming 216 programming guide features guide references none.

  • Page 217: [429]

    General programming programming guide 217 [429] isdn extension progress tone description enables or disables to send the progress tone to isdn extension on isdn port basis. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 through 12, ( =all ports) • enable / disable (n...

  • Page 218

    General programming 218 programming guide features guide references none.

  • Page 219: [430]

    General programming programming guide 219 [430] did / tie format number assignment description assigns a direct inward dialing (did) and tie format number to each outside line group. Selection • outside line group (trg) number: 1 through 8, ( =all outside line groups) • did / tie format number: 1 to...

  • Page 220: [431]

    General programming 220 programming guide [431] did / tie incoming assignment description assigns a did / tie incoming method, immediate or wink, to each did / tie format according to your central office service. Immediate: incoming did and tie calls can be received right after the receiving signal ...

  • Page 221

    General programming programming guide 221 features guide references direct inward dialing (did) t1 line.

  • Page 222: [432]

    General programming 222 programming guide [432] did / tie outgoing assignment description assigns a did and tie outgoing method, immediate or wink, to each did / tie format according to your central office service. Immediate: outgoing did and tie numbers can be transmitted right after seizing the ou...

  • Page 223

    General programming programming guide 223 features guide references direct inward dialing (did) t1 line.

  • Page 224: [433]

    General programming 224 programming guide [433] did / tie subscriber number removed digit description assigns the removed digits of received a did and tie subscriber number for each did / tie format. In this case, digits are removed from the beginning of the received digits. Selection • did / tie fo...

  • Page 225

    General programming programming guide 225 tie line service.

  • Page 226: [434]

    General programming 226 programming guide [434] did / tie added number description assigns the added number to the did and tie subscriber number which is determined in program [433] did / tie subscriber number removed digit. This makes the final number which serves as the extension number. Note that...

  • Page 227

    General programming programming guide 227 t1 line tie line service.

  • Page 228: [435]

    General programming 228 programming guide [435] did / tie wink time out assignment description the did / tie outgoing method can be set to the wink mode in program [432] did / tie outgoing assignment. This program sets the time the system waits for the confirmation wink signal after an outside line ...

  • Page 229

    General programming programming guide 229 features guide references direct inward dialing (did) t1 line tie line service.

  • Page 230: [436]

    General programming 230 programming guide [436] co-to-tie transfer description enables or disables transferring an incoming outside call to the tie line on an outside (co) line group basis. This restriction applies to the following: 1) call forwarding to a tie line 2) call transfer to a tie line. Se...

  • Page 231: [437]

    General programming programming guide 231 [437] tie-to-co transfer description enables or disables transferring tie calls to an outside line on an outside line group basis. This restriction applies to the following: 1) an outside call through another pbx 2) call forwarding to an outside line 3) call...

  • Page 232: [438]

    General programming 232 programming guide [438] tie-to-tie transfer description enables or disables transferring tie calls to a tie line on an outside line group basis. This restriction applies to the following: 1) a tie call through another pbx 2) call forwarding to a tie line 3) call transfer to a...

  • Page 233: [439]

    General programming programming guide 233 [439] tie security type description assigns the security mode for tie calls. There are two modes, non security and trunk security (outside line security). Non security mode allows the caller to access an outside line without dialing a tie user code. Trunk se...

  • Page 234: [440]

    General programming 234 programming guide [440] line hunting sequence description assigns the hunting sequence of idle lines, seizing from the smallest to the largest line number or vice versa in an outside line group, on an outside line group basis. Selection • outside line group (trg) number: 1 th...

  • Page 235: [453]

    General programming programming guide 235 [453] spid assignment description assigns a maximum of eight service profile identifiers (spid) on an isdn port basis. Selection • port number: kx-td816 — 01 through 04 kx-td1232 — 01 through 12 • location number: 1 through 8 • spid: 20 digits (max.) default...

  • Page 236

    General programming 236 programming guide • for the kx-td1232, port numbers 01 through 06 are for the master system and 07 through 12 are for the slave, if available. • refer to program [423] for the list of the isdn port numbers and their corresponding jack numbers. Features guide references integr...

  • Page 237: [454]

    General programming programming guide 237 [454] dn assignment description assigns a maximum of eight directory numbers (dn) on an isdn port basis. Selection • port number: kx-td816 — 01 through 04 kx-td1232 — 01 through 12 • location number: 1 through 8 • dn: 20 digits (max.) default all ports — all...

  • Page 238

    General programming 238 programming guide • for the kx-td1232, port numbers 01 through 06 are for the master system and 07 through 12 are for the slave, if available. • refer to program [423] for the list of the isdn port numbers and their corresponding jack numbers. Features guide references integr...

  • Page 239: [455-456]

    General programming programming guide 239 [455-456] extension ringing assignment —— day / night for isdn description determines which extension receives a call on a dn basis of the isdn port in both the day and night modes. Selection • port number: kx-td816 — 01 through 04 kx-td1232 — 01 through 12 ...

  • Page 240

    General programming 240 programming guide • for the kx-td1232, port numbers 01 through 06 are for the master system and 07 through 12 are for the slave, if available. • refer to program [423] for the list of the isdn port numbers and their corresponding jack numbers. • assignable numbers are program...

  • Page 241: [457-458]

    General programming programming guide 241 [457-458] dil 1:1 — lunch / break group description assigns a lunch / break group to each dil1:1 destination. Selection • outside (co) line number: kx-td816 — 01 through 08 kx-td1232 — 01 through 24 • group number: 1 through 8 default all outside lines — bla...

  • Page 242

    General programming 242 programming guide display: co line no? 3. Enter an outside line number. To enter outside line number 01, you can also press next. Display example: co01: 4. Enter a group number. To change the current entry, press clear and the new number. Display example: co01:1 5. Press stor...

  • Page 243: [460]

    General programming programming guide 243 [460] pri connection assignment description assigns the number of b channels which are actually used out of the 23 pri line channels. This program is only available for the kx-td1232 with the primary rate interface isdn expansion unit (kx-td290). Selection •...

  • Page 244: [461]

    General programming 244 programming guide [461] pri line coding assignment description sets a line coding for the pri isdn line. This program is only available for the kx-td1232 with the primary rate interface isdn expansion unit (kx-td290). Selection • b8zs / ami default b8zs programming 1. Enter 4...

  • Page 245: [462]

    General programming programming guide 245 [462] pri frame sequence assignment description sets a frame format for the pri isdn line. This program is only available for the kx-td1232 with the primary rate interface isdn expansion unit (kx-td290). Selection • esf (extend multiframe) / f4 (4-frame mult...

  • Page 246: [463]

    General programming 246 programming guide [463] pri timer 1 and timer 2 assignment description this pbx employs en-bloc dialing so that dialed digits are not transmitted to the central office until all digits have been entered into the pbx. This assignment selects whether timers and a counter (pri d...

  • Page 247

    General programming programming guide 247 conditions • to assign all outside lines to one selection, press the key in step 3. In this case, the display shows the contents programmed for outside line 25. Features guide references integrated services digital network (isdn) — primary rate interface (pr...

  • Page 248: [464]

    General programming 248 programming guide [464] pri inter digit timer 1 assignment description assigns inter-digit timeout for timer 1. For details, please see "description" of [463] pri timer 1 and timer 2 assignment. This program is only available for the kx-td1232 with the primary rate interface ...

  • Page 249: [465]

    General programming programming guide 249 [465] pri inter digit timer 2 assignment description assigns inter-digit timeout for timer 2. For details, please see "description" of [463] pri timer 1 and timer 2 assignment. This program is only available for the kx-td1232 with the primary rate interface ...

  • Page 250: [466]

    General programming 250 programming guide [466] pri dial counter for inter digit timer 2 assignment description assigns counter value of dialed digits. Before this value, timer 1 is used. After this value, timer 2 is used. For details, please see "description" of [463] pri timer 1 and timer 2 assign...

  • Page 251: [467-468]

    General programming programming guide 251 [467-468] dil 1:1 extension —— lunch / break description the dil 1:1 feature allows incoming outside calls to be directed to a specific extension. These programs specify the extension number for lunch or break mode. If this program has been assigned to "disa...

  • Page 252

    General programming 252 programming guide • you set the extension numbers in program [003] extension number set, voice mail extension numbers in program [118] voice mail extension number assignment, phantom extension numbers in program [124] phantom extension number assignment or floating numbers, d...

  • Page 253: 2.6

    General programming programming guide 253 2.6 cos programming [500-501] toll restriction level —— day / night description each extension must be assigned a class of service (cos). These programs set the toll restriction value for each cos in day or night mode. Selection • cos number: 1 through 8, ( ...

  • Page 254

    General programming 254 programming guide features guide references night service toll restriction.

  • Page 255: [502]

    General programming programming guide 255 [502] extension-to-outside line call duration limit description this program allows you to restrict the duration of outside calls on a class of service (cos) basis. Selection • cos number: 1 through 8, ( =all cos) • disable (no limit) / enable (limit) defaul...

  • Page 256

    General programming 256 programming guide • program [990] system additional information, area 02 - bit 2 is used to program limited call duration to be done for outgoing calls only. Features guide references call forwarding — to outside line call transfer, screened — to outside line conference, unat...

  • Page 257: [503]

    General programming programming guide 257 [503] call transfer to outside line description this program determines which classes of services (cos) are allowed to perform the call transfer to outside line function. Selection • cos number: 1 through 8, ( =all cos) • enable / disable default all cos — d...

  • Page 258: [504]

    General programming 258 programming guide [504] call forwarding to outside line description this program determines which classes of services (cos) are allowed to perform the call forwarding to outside line function. Selection • cos number: 1 through 8, ( =all cos) • disable / enable default all cos...

  • Page 259: [505]

    General programming programming guide 259 [505] executive busy override description determines which classes of services (cos) are allowed to perform executive busy override — extension / outside line. Executive busy override allows the user to interrupt an established call. Selection • cos number: ...

  • Page 260: [506]

    General programming 260 programming guide [506] executive busy override deny description this program is used to determine which classes of services (cos) are allowed to deny executive busy override. Executive busy override deny allows the user to prevent executive busy override — extension / outsid...

  • Page 261: [507]

    General programming programming guide 261 [507] do not disturb override description this program determines which classes of services (cos) are allowed to perform do not disturb (dnd) override. Selection • cos number: 1 through 8, ( =all cos) • disable / enable default all cos — disable programming ...

  • Page 262: [508]

    General programming 262 programming guide [508] account code entry mode description there are three account code modes: option, verified-all calls and verified-toll restriction override. This program determines the mode to be used by each class of service (cos). Option mode: the user can enter any a...

  • Page 263

    General programming programming guide 263 • program [105] account codes is used to define the account codes for the verified modes. • program [601] class of service is used to assign a class of service to each extension. Features guide references account code entry toll restriction override by accou...

  • Page 264: [509]

    General programming 264 programming guide [509] off-hook call announcement (ohca) description enables or disables to perform the off-hook call announcement (ohca) on a class of service (cos) basis. Selection • cos number: 1 through 8, ( =all cos) • enable / disable default all cos — enable programmi...

  • Page 265: [510]

    General programming programming guide 265 [510] night service access description enables or disables switching the day / night service on a class of service (cos) basis. Selection • cos number: 1 through 8, ( =all cos) • enable / disable default all cos — disable programming 1. Enter 510. Display: 5...

  • Page 266: [511]

    General programming 266 programming guide [511] pits programming level description regulates station programming, depending on the cos. This programming has two levels as follows. Level 1: enables all station programming. Level 2: disables co button programming in station programming. Selection • co...

  • Page 267

    General programming programming guide 267 features guide references none.

  • Page 268: 2.7

    General programming 268 programming guide 2.7 extension programming [600] extra device port description extra device port (xdp) allows a single line telephone to be connected to the same jack as a digital proprietary telephone (dpt). This program assigns which jacks are xdp. The single line telephon...

  • Page 269

    General programming programming guide 269 • to assign all jacks to one selection, press the key in step 3. In this case, the display shows the contents programmed for jack 01. • immediately after changing your assignment, the changed setting may not work for a maximum of eight seconds. Features guid...

  • Page 270: [601]

    General programming 270 programming guide [601] class of service description programs each extension for class of service (cos). The cos determines the call handling abilities of each extension. Selection • jack number: kx-td816 — 01 through 16, (-1 / -2), kx-td1232 — 01 through 64, (-1 / -2), ( =al...

  • Page 271

    General programming programming guide 271 • for the kx-td1232, jack numbers 01 through 32 are for the master system and 33 through 64 are for the slave, if available. Jack numbers in the out-of-service system are unacceptable. • for an explanation of jack numbering, see "rotation of jack number" in ...

  • Page 272: [602]

    General programming 272 programming guide [602] extension group assignment description assigns each extension to an extension group. Extension groups are used for group call pickup, station hunting, and paging — group. Selection • jack number: kx-td816 — 01 through 16, (-1 / -2), kx-td1232 — 01 thro...

  • Page 273

    General programming programming guide 273 • for an explanation of jack numbering, see "rotation of jack number" in section 1.3 programming methods. • to assign all jacks to one extension group, press the key in step 3. In this case, the display shows the contents programmed for jack 01. Features gui...

  • Page 274: [603-604]

    General programming 274 programming guide [603-604] dil 1:n extension and delayed ringing —— day / night description the direct in lines (dil) 1:n feature can be assigned to ring more than one extension. All incoming calls from the programmed outside lines are directed to the specified extensions. T...

  • Page 275

    General programming programming guide 275 9. Press end. Conditions • an extension can be assigned as the destination of as many outside lines as required. • for the kx-td1232, jack numbers 01 through 32 are for the master system and 33 through 64 are for the slave, if available. Jack numbers in the ...

  • Page 276: [605-606]

    General programming 276 programming guide [605-606] outgoing permitted outside line assignment —— day / night description determines the outside lines which can be accessed by an extension in both day and night modes. The extension users can make outgoing outside calls using the assigned outside lin...

  • Page 277

    General programming programming guide 277 conditions • for the kx-td1232, jack numbers 01 through 32 are for the master system and 33 through 64 are for the slave, if available. Jack numbers in the out-of-service system are unacceptable. • for an explanation of jack numbering, see "rotation of jack ...

  • Page 278: [607-608]

    General programming 278 programming guide [607-608] doorphone ringing assignment —— day / night description these programs assign the extensions which will ring when a doorphone call is received during the day and night modes. Programmed extensions are also allowed to open the door. Selection • jack...

  • Page 279

    General programming programming guide 279 • for an explanation of jack numbering, see "rotation of jack number" in section 1.3 programming methods. • to assign all jacks to one selection, press the key in step 3. In this case, the display shows the contents programmed for jack 01. • four doorphones ...

  • Page 280: [609]

    General programming 280 programming guide [609] voice mail access codes description assigns a mailbox number for each extension, only if program [990] system additional information, area 02 - bit 8 is set to "free". Selection • jack number: kx-td816 — 01 through 16, (-1 / -2), kx-td1232 — 01 through...

  • Page 281

    General programming programming guide 281 • for an explanation of jack numbering, see "rotation of jack number" in section 1.3 programming methods. • the system supports a maximum of eight jacks (16 jacks during system connection *1 ) for connection to a voice processing system as the voice mail or ...

  • Page 282: [610]

    General programming 282 programming guide [610] live call screening recording mode assignment description • assigns whether to close the mailbox or keep recording the conversation after a call is intercepted. • this program is available when the digital super hybrid system is connected to a digital ...

  • Page 283

    General programming programming guide 283 • to assign all jacks to one selection, press the key in step 3. In this case, the display shows the contents programmed for jack 01. Features guide references live call screening (lcs) voice mail integration for digital proprietary telephones.

  • Page 284: [613]

    General programming 284 programming guide [613] isdn class of service description programs a class of service (cos) number for each isdn extension port. The cos determines the call handling abilities of each port. Selection • port number: kx-td816 — 01 through 04, ( =all ports) kx-td1232 — 01 throug...

  • Page 285

    General programming programming guide 285 • to assign all ports to one selection, press the key in step 3. In this case, the display shows the contents programmed for port 01. Features guide references class of service (cos).

  • Page 286: [614-615]

    General programming 286 programming guide [614-615] outgoing permitted outside line assignment —— day / night for isdn extension description determines which outside lines can be accessed by an isdn extension in both the day and night modes. The extension users can make outgoing outside calls using ...

  • Page 287

    General programming programming guide 287 conditions • port numbers 01 through 06 are for the master system and 07 through 12 are for the slave, if available. • refer to program [423] for the list of the isdn port numbers and their corresponding jack numbers. • to assign all ports to one selection, ...

  • Page 288: [619]

    General programming 288 programming guide [619] extension call forwarding — no answer time description sets a call forwarding – no answer time for each extension. Selection • jack number: kx-td816 — 01 through 16 (-1 / -2), kx-td1232 — 01 through 64 (-1 / -2), (-1 = first part, -2 = second part, =al...

  • Page 289: [620]

    General programming programming guide 289 [620] lunch / break group assignment description assigns extensions for a lunch / break group. A lunch / break group can be assigned to up to 8 extensions (pt / slt). Selection • group number: 1 through 8 • location number: 1 through 8 • extension number: 2 ...

  • Page 290

    General programming 290 programming guide features guide references lunch / break service night service.

  • Page 291: [621]

    General programming programming guide 291 [621] cordless pits extension port description prevents the cordless pits speakerphone functions from working in the following cases, if connected to extension ports such as kx-t7890; 1. Bgm: start or end the bgm. 2. Lcs: work on the private mode even if the...

  • Page 292

    General programming 292 programming guide conditions • if "yes" is selected for a jack for wired pits, the speakerphone functions written in the description do not work. Connect a cordless pits if "yes" is selected. Features guide references none.

  • Page 293: [622]

    General programming programming guide 293 [622] extension clip number assignment description assigns the identification number of the calling party to each extension in order to utilize the calling line identification presentation (clip) feature provided by the isdn line service. This program is onl...

  • Page 294

    General programming 294 programming guide • to display parts of the number which have scrolled off the display or . • for an explanation of jack numbering, see "rotation of jack number" in section 1.3 programming methods. • to assign all jacks to one extension group, press the key in step 3. In this...

  • Page 295: [624]

    General programming programming guide 295 [624] isdn extension clip number assignment description assigns the identification number of the calling party to each isdn extension in order to utilize the calling line identification presentation (clip) feature provided by the isdn line service. This prog...

  • Page 296

    General programming 296 programming guide • to assign all ports to one selection, press the key in step 3. In this case, the display shows the contents programmed for port 07. Features guide references integrated services digital network (isdn) — primary rate interface (pri).

  • Page 297: 2.8

    General programming programming guide 297 2.8 t1 programming [700] t1 channel assignment description assigns a channel type to each t1 channel. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • channel type: lcot / gcot / did / tie ...

  • Page 298: [701]

    General programming 298 programming guide [701] t1 dial mode description assigns a signal type to each t1 channel. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • signal type: pulse-10 / pulse-20 / dtmf-80 / dtmf-160 default all t...

  • Page 299: [702]

    General programming programming guide 299 [702] t1 cot cpc (in) description sets a cpc signal detection time to each t1 channel, assigned cot, on receiving a call. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • time: 00 through 7...

  • Page 300: [703]

    General programming 300 programming guide [703] t1 did cpc (in) description sets a cpc signal detection time to each t1 channel, assigned did, on receiving a call. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • time: 00 through 1...

  • Page 301: [704]

    General programming programming guide 301 [704] t1 cot cpc (out) description sets a cpc signal detection time to each t1 channel, assigned cot, on making a call. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • time: 00 through 75 ...

  • Page 302: [705]

    General programming 302 programming guide [705] t1 did cpc (out) description sets a cpc signal detection time to each t1 channel, assigned did, on making a call. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • time: 00 through 15 ...

  • Page 303

    General programming programming guide 303 t1 line.

  • Page 304: [706]

    General programming 304 programming guide [706] t1 did receive digits description sets a maximum number of the received dial digits for each t1 channel assigned did. This program is available for the kx-td1232 only. Selection • t1 channel number: 01 through 24, ( =all t1 channels) • digits: 1 throug...

  • Page 305

    General programming programming guide 305 features guide references direct inward dialing (did) t1 line.

  • Page 306: [707]

    General programming 306 programming guide [707] t1 clock mode description assigns a clock mode for the t1 line. This program is available for the kx-td1232 only. Selection • internal / external default external programming 1. Enter 707. Display: 707 clock mode 2. Press next. Display: external 3. Kee...

  • Page 307: [708]

    General programming programming guide 307 [708] t1 line coding description sets a line coding for the t1 line. This program is available for the kx-td1232 only. Selection • b8zs / ami default b8zs programming 1. Enter 708. Display: 708 line coding 2. Press next. Display: b8zs 3. Keep pressing select...

  • Page 308: [709]

    General programming 308 programming guide [709] t1 frame sequence description sets a frame format for the t1 line. This program is available for the kx-td1232 only. Selection • esf / d4 default esf programming 1. Enter 709. Display: 709 frame seq 2. Press next. Display: esf 3. Keep pressing select u...

  • Page 309: [710]

    General programming programming guide 309 [710] t1 frame option description assigns an esf frame option for the t1 line. This is only available when the esf is selected on the frame sequence. This program is available for the kx-td1232 only. Selection • c=a, d=b / c=0, d=0 / c=1, d=0 / c=0, d=1 / c=...

  • Page 310: [711]

    General programming 310 programming guide [711] t1 first dial timer (co) description sets a timer to prevent a first dial being sent too early on the t1 channels assigned cot. This program is available for the kx-td1232 only. Selection • time: 01 – 16 ( 0.5 seconds is the actual time) default 02 pro...

  • Page 311: [712]

    General programming programming guide 311 [712] t1 first dial timer (did / tie) description sets a timer to prevent the first dial being sent too early on the t1 channels assigned did and tie. This program is available for the kx-td1232 only. Selection • time: 001 – 255 ( 32 milliseconds is the actu...

  • Page 312: [713]

    General programming 312 programming guide [713] t1 %break description sets a "%break" for the t1 line assigned pulse. This program is available for the kx-td1232 only. Selection • 60% / 67% default 60% programming 1. Enter 713. Display: 713 t1 %break 2. Press next. Display: t1 %break:60% 3. Keep pre...

  • Page 313: [714]

    General programming programming guide 313 [714] t1 dial click tone description sets to send a dial click tone of the t1 line. This program is available for the kx-td1232 only. Selection • yes (to send) / no (not to send) default yes programming 1. Enter 714. Display: 714 click tone 2. Press next. Di...

  • Page 314: [715]

    General programming 314 programming guide [715] t1 inter digit pause description sets a time of the inter digit pause for the t1 line. This program is available for the kx-td1232 only. Selection • 630 msec / 830 msec / 1030 msec default 830 msec programming 1. Enter 715. Display: 715 digit pause 2. ...

  • Page 315: [716]

    General programming programming guide 315 [716] t1 flash detection description sets a flash detection time for the t1 line. This program is available for the kx-td1232 only. Selection • disable / 208-1016 msec / 80-1016 msec / 208-1544 msec / 80-1544 msec default disable programming 1. Enter 716. Di...

  • Page 316: [717]

    General programming 316 programming guide [717] t1 answer decision timer description sets an answering detection time for the t1 line. This program is available for the kx-td1232 only. Selection • time: 001 through 255 ( 32 milliseconds is the actual time) default 001 programming 1. Enter 717. Displ...

  • Page 317: [718]

    General programming programming guide 317 [718] t1 break detection description sets a break detection time for the t1 extension. This program is available for the kx-td1232 only. Selection • time: 16 – 96 ms / 16 – 136 ms default 16 – 96 ms programming 1. Enter 718. Display: 718 break length 2. Pres...

  • Page 318: [719]

    General programming 318 programming guide [719] t1 pulse type description sets a dialing pulse type for the t1 line. This program is available for the kx-td1232 only. Selection • type-a / type-b / type-c default type-a programming 1. Enter 719. Display: 719 pulse type 2. Press next. Display: type-a ...

  • Page 319: [720]

    General programming programming guide 319 [720] t1 tie ringing service description sets a type to receive a call in the t1 channels assigned tie/did. If "dil" is selected, dil 1:1 or dil 1:n will perform. This program is available for the kx-td1232 only. Selection • outside (co) line number: 25 thro...

  • Page 320

    General programming 320 programming guide tie line service.

  • Page 321: [721]

    General programming programming guide 321 [721] t1 / pri reference co description assigns a reference outside (co) line number when t1 channel or pri isdn channel is used as an outside line. This program is available for the kx-td1232 only. Selection • outside (co) line number: 25 through 48, ( = al...

  • Page 322

    General programming 322 programming guide conditions • refer the data assigned in the programs as follows. [407-408] dil 1:1 extension —— day / night [419] isdn outgoing clir service assignment [420] isdn ring service assignment [457-458] dil 1:1 — lunch / break group [467-468] dil 1:1 extension —— ...

  • Page 323: [722]

    General programming programming guide 323 [722] t1 answer wait timer description assigns an automatic disconnect timer to stop making a call on tie / did line, if the called party does not answer. This program is available for the kx-td1232 only. Selection • outside (co) line number: 25 through 48, ...

  • Page 324

    General programming 324 programming guide t1 line tie line service.

  • Page 325: [723]

    General programming programming guide 325 [723] t1 sending tie caller id description sends a caller id on the dtmf (dual tone multi-frequency) signaling on the t1 channels assigned tie. This program is available for the kx-td1232 only. Selection • outside (co) line number: 25 through 48, ( = all out...

  • Page 326

    General programming 326 programming guide tie line service.

  • Page 327: [725]

    General programming programming guide 327 [725] t1 extension number description assigns an extension number of the t1 channels set opx. This program is available for the kx-td1232 only. Selection • port number: 01 through 24, • extension number: 2 or 4 digits default all ports — not stored programmi...

  • Page 328: [726]

    General programming 328 programming guide [726] t1 extension name description assigns names to the extension numbers of t1 channel set opx, programmed in [725] t1 extension number. This program is available for the kx-td1232 only. Selection • port number: 01 through 24, ( = all ports) • name: 10 cha...

  • Page 329

    General programming programming guide 329 features guide references display, call information intercom calling t1 line.

  • Page 330: [727]

    General programming 330 programming guide [727] t1 extension cos number description assigns a "class of service (cos)" to each extension of t1 channels. This program is available for the kx-td1232 only. Selection • port number: 01 through 24, ( = all ports) • cos number: 1 through 8 default all port...

  • Page 331

    General programming programming guide 331 t1 line.

  • Page 332: [728]

    General programming 332 programming guide [728] t1 extension outgoing permitted outside line assignment – day description determines the outside lines which can be accessed by an extension on the t1 line in day mode. The extension user on the t1 line can make outgoing outside line calls using the as...

  • Page 333

    General programming programming guide 333 conditions none features guide references outside line connection assignment — outgoing night service t1 line.

  • Page 334: [729]

    General programming 334 programming guide [729] t1 extension outgoing permitted outside line assignment – night description determines the outside lines which can be accessed by an extension on the t1 line in night mode. The extension user on the t1 line can make outgoing outside line calls using th...

  • Page 335

    General programming programming guide 335 conditions none features guide references night service t1 line.

  • Page 336: [730]

    General programming 336 programming guide [730] t1 extension voice mail access codes description assigns a mailbox number for each extension on the t1 line, "[990] system additional information, area 02 - bit 8" is set to free. This program is available for the kx-td1232 only. Selection • port numbe...

  • Page 337

    General programming programming guide 337 • to display parts of the mailbox number which have scrolled off the display, press or . Features guide references t1 line voice mail integration.

  • Page 338: 2.9

    General programming 338 programming guide 2.9 resource programming [800] smdr incoming / outgoing call log printout description used to determine which calls will produce a station message detail recording (smdr) printout. Selection • outgoing calls: all (all calls) / toll (toll calls only) / off (n...

  • Page 339

    General programming programming guide 339 features guide references station message detail recording (smdr).

  • Page 340: [801]

    General programming 340 programming guide [801] smdr format description used to match the smdr output to the paper size being used in the printer. Page length determines the number of lines per page. Skip perforation determines the number of lines to be skipped at the end of every page. Selection • ...

  • Page 341: [802]

    General programming programming guide 341 [802] system data printout description starts or stops printing the system data. All or a specific range of the current system- programmed data is printed out. The ranges are as follows: manager: manager programming [000] through [017] system: system program...

  • Page 342

    General programming 342 programming guide 4. Press store to start printing. Printing starts. To stop printing, press select and go to step 4. When printing is completed, the display shows: display: print-out:finish 5. Press store. Display: print-out:stop 6. Press end. Conditions • it is necessary to...

  • Page 343: [803]

    General programming programming guide 343 [803] music source use description assigns the music source to be used for music on hold and background music (bgm). Selection • hold / bgm • music source number: kx-td816 —1 / no use kx-td1232 — 1 through 4 / no use default hold and bgm — music 1 programmin...

  • Page 344

    General programming 344 programming guide features guide references background music (bgm) background music (bgm) — external music on hold.

  • Page 345: [804]

    General programming programming guide 345 [804] external pager bgm description used to determine which external pagers will receive background music (bgm). Bgm — external is turned on and off by the operator or manager. Selection • external pager number: kx-td816 — 1 kx-td1232 — 1 through 4 • disabl...

  • Page 346

    General programming 346 programming guide features guide references background music (bgm) — external.

  • Page 347: [805]

    General programming programming guide 347 [805] external pager confirmation tone description used to remove the confirmation tone for external pagers. The default setting sends confirmation tone 2 to the external pagers before paging is broadcast. This programming applies to all the external pagers....

  • Page 348: [806-807]

    General programming 348 programming guide [806-807] serial interface (rs-232c) parameters description assigns the communication parameters for the serial interface (rs-232c) interface for port 1 (for kx-td816 and master system of kx-td1232) or port 2 (for slave system of kx- td1232). New line code: ...

  • Page 349

    General programming programming guide 349 5. Press next to program baud rate. Display example: baud rate:9600 6. Keep pressing select until the desired selection is displayed. 7. Press store. 8. Press next to program word length. Display example: word lengt:8bits 9. Keep pressing select until the de...

  • Page 350: [809]

    General programming 350 programming guide [809] disa security type description assigns the security mode for outside calls attempted by the disa (direct inward system access) caller. There are three modes: non security, trunk security (outside line security), and all security. Non security mode allo...

  • Page 351: [810]

    General programming programming guide 351 [810] disa tone detection description enables or disables tone detection for outside-to-outside line calls via the direct inward system access (disa) feature. Enabling tone detection allows the system to detect the end of the call. This program is available ...

  • Page 352: [812]

    General programming 352 programming guide [812] disa dtmf repeat description selects whether the system transmits dtmf (dual tone multi-frequency) signals directly to the central office (co) or if the system repeats the dtmf signals to co in order to adjust gain. This can be done for an outside-to-o...

  • Page 353: [813]

    General programming programming guide 353 [813] floating number assignment description assigns the floating numbers for external pagers, disa (direct inward system access) *1 messages, modem and extension groups. These numbers can be used the same way extension numbers are used for station access. S...

  • Page 354

    General programming 354 programming guide conditions • a floating number is composed of two to four numerical digits, 0 through 9. • the first one or two digits of the floating numbers are subject to program [100] flexible numbering, (01) through (16) 1st through 16th hundred extension blocks. • flo...

  • Page 355: [814]

    General programming programming guide 355 [814] modem standard description assigns the modem standard. There are two standards available — bell and ccitt. Selection bell / ccitt default bell programming 1. Enter 814. Display: 814 modem type 2. Press next. Display example: modem:bell 3. Keep pressing...

  • Page 356: [815]

    General programming 356 programming guide [815] disa built-in auto attendant description assigns the disa (direct inward system access) built-in auto attendant number. The extension number and the floating number can be assigned as a one digit number and used as a disa built-in auto attendant number...

  • Page 357: [817]

    General programming programming guide 357 [817] kx-td197 / kx-td198 baud rate set description assigns the kx-td197 / kx-td198 standard. There are two standards available — bell and ccitt-v.34. Selection bell / v.34-9600 / v.34-14400 / v.34-19200 / v.34-28800 / v.34-33600 default v.34-33600 programmi...

  • Page 358: [818]

    General programming 358 programming guide [818] doorphone tone frequency selection description assigns a ringer frequency to each doorphone. There are eight tone types. Selection • doorphone number: kx-td816 — 1 through 4, ( = all doorphones) kx-td1232 — 1 through 8, ( = all doorphones) • type1 / ty...

  • Page 359: [820]

    General programming programming guide 359 [820] doorphone ringing time description selects the doorphone ringing time. Selection • doorphone number: kx-td816 — 1 through 4, ( = all doorphones) kx-td1232 — 1 through 8, ( = all doorphones) • 15sec / 30sec (seconds) default all doorphones — 30sec progr...

  • Page 360: 2.10

    General programming 360 programming guide 2.10 optional programming [990] system additional information description allows the following programming items to be changed, if required. Each bit in each area represents a programming item. 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 display example area 01 b...

  • Page 361

    General programming programming guide 361 explanation area bit description selection default references 01 1 sound source during transfer. 0 : ringback tone 1 : music on hold 1 • call transfer features • music on hold 2 result of pressing the hookswitch lightly and then replacing the handset (during...

  • Page 362

    General programming 362 programming guide 02 1 if an outside party is transferred and unanswered, assigns whether transfer recall occurs at the originating transfer extension or at the operator 1. 0 : initiating extension 1 : operator 1 0 call transfer, unscreened - to extension 2 if limited call du...

  • Page 363

    General programming programming guide 363 02 7 an outside line set to pulse or call blocking mode in program [402] dial mode selection can have two settings. This assigns the pulse break ratio during dial pulsing. Select an an appropriate ratio depending on the standard in your country. 0 : 60 % 1 :...

  • Page 364

    General programming 364 programming guide 03 1-16 this bit is provided to assign pad switch control (volume control of received calls on an outside line). This can be assigned per outside line. The outside line numbers [1] through [8] correspond to outside lines 1 through 8 for kx-td816, and outside...

  • Page 365

    General programming programming guide 365 05 1 enables or disables the automatic time adjustment by caller id information once a day by the first call received after 3:00am. 0 : enable 1 : disable 1 caller id 2 an outside-to-outside disa call can be prolonged many times. This bit specifies how many ...

  • Page 366

    General programming 366 programming guide 05 8 unused 9 enables or disables dial tone 2 when an extension sets programmable extension features such as call waiting. 0 : disable 1 : enable 1 none 10 determines the result when pressing the flash or flash / rcl button during an outside call (when area ...

  • Page 367

    General programming programming guide 367 06 1 determines whether the account code is printed out or not (shown in dot) in the smdr. 0: not printed out 1: printed out 1 account code entry 3, 2 reserved 4 enables or disables sending outside (co) line access code "9" to a tie line. When you dial outsi...

  • Page 368

    General programming 368 programming guide 07 1 enables or disables the dtmf signal to the isdn line. 0 : enable 1 : disable 1 direct inward system access (disa) 2-4 unused 5 enables or disables the hooking signal when the reverse signal does not return. 0 : disable 1 : enable 1 none 6 reserved 7 all...

  • Page 369

    General programming programming guide 369 08 1 sends a dial tone to another system when a channel assigned on tie is captured. 0 : send 1 : not send 1 tie line service 2 unused 3 sends a dial tone to extensions when a tie line access code is dialed. 0 : send 1 : not send 1 tie line service 4-16 unus...

  • Page 370

    General programming 370 programming guide selection • area code: 01 through 10 • selection: see "selection" shown in the lists for each area. Default see "default" shown in the lists. Programming 1. Enter 990. Display: 990 sys add data 2. Press next. Display: area no? 3. Enter an area code. 10 1-8 s...

  • Page 371

    General programming programming guide 371 display example: 0010100011111001 4. Keep pressing or to move the cursor to the desired bit. 5. Enter your selection. To change the current entry, press store and the new selection. 6. To program another bit, repeat steps 4 and 5. 7. Press store. 8. To progr...

  • Page 372: [991]

    General programming 372 programming guide [991] cos additional information description adds the following programming items on a class of service (cos) basis, if required. Bits 1-8: cos additional information bits 9-16: system additional information cos 1-8 there are 8 bits available in bit 1-8 as f...

  • Page 373

    General programming programming guide 373 system additional information 2 cos 3-6 there are 8 bits available in system additional information area as follows: explanation for cos 3 bit description selection default features guide references 10, 9 when an incoming call reaches an extension in the sta...

  • Page 374

    General programming 374 programming guide 15 determines where "rt" of the sequence returns in the ucd (ring group) time table 4. 0 : second 1 : top 1 • ring group • uniform call distribution (ucd) 16 unused explanation for cos 4 bit description selection default features guide references 9 selects e...

  • Page 375

    General programming programming guide 375 12 determines the destination when an incoming call arrives at voice mail, if all vm ports are busy. Wait: the call waits until a vm port becomes free. Irna destination: the call is forwarded to the irna destination immediately. 0 : wait 1 : irna destination...

  • Page 376

    General programming 376 programming guide selection • cos number: 1 through 8, ( =all cos) • selection : see "selection" shown in the lists. Default see "default" shown in the lists. Programming 1. Enter 991. Display: 991 cos add data 2. Press next. Display: cos no? 3. Enter a cos number. Display ex...

  • Page 377: Section

    Default values programming guide 377 section 3 default values.

  • Page 378

    Default values 378 programming guide 2 general programming program default [000] date and time set '93 jan. 1 fri 12:00 am 12 [001] system speed dialing number set all speed dial numbers - not stored [002] system speed dialing name set all speed dial numbers - not stored [003] extension number set k...

  • Page 379

    Default values programming guide 379 [017] disa user codes code 01=blank — cos 8 code 02=blank — cos 8 : code 32=blank — cos 8 [100] flexible numbering see "feature number list" above. [101] day / night service switching mode manual [102] day / night service starting time every day of the week — day...

  • Page 380

    Default values 380 programming guide [118] voice mail extension number assignment kx-td816 — vm-01=165, vm-02=166, vm-03=167, vm- 04=168, vm-05=169, vm-06=170, vm-07=177, vm-08=178, vm-09=181, vm-10=182, vm- 11=183, vm-12=184 kx-td1232 — vm-01=165, vm-02=166, vm-03=167, vm- 04=168, vm-05=169, vm-06=...

  • Page 381

    Default values programming guide 381 [136] did number assignment all locations — not stored [137-138] did extension —— day / night all locations — not stored [139] did extension name set all locations — not stored [148] off-hook monitor enable [150] lunch service starting / ending time every day of ...

  • Page 382

    Default values 382 programming guide [219] call park recall time 12 rings [220] tie first / inter digit time 5 sec [300] trs override for system speed dialing disable [301-305] trs denied code entry for levels 2 through 6 all locations — not stored [306-310] trs excepted code entry for levels 2 thro...

  • Page 383

    Default values programming guide 383 [401] outside line group assignment co01 — trg 1; co02 — trg 2; co03 — trg 3; co04 — trg 4; co05 — trg 5; co06 — trg 6; co07 — trg 7; co08 — trg 8 (for kx-td816) co08 through co48 — trg 8 (for kx-td1232) [402] dial mode selection all outside lines — dtmf [403] pu...

  • Page 384

    Default values 384 programming guide [424] isdn layer 1 active mode all ports — permanent [425] isdn configuration all ports — multipoint [426] isdn data link mode all ports — permanent [427] isdn tei mode all ports — automatic [428] isdn extension multiple directory number all ports — disable [429]...

  • Page 385

    Default values programming guide 385 [462] pri frame sequence assignment esf [463] pri timer 1 and timer 2 assignment all outside lines — effective [464] pri inter digit timer 1 assignment 5sec [465] pri inter digit timer 2 assignment 3sec [466] pri dial counter for inter digit timer 2 assignment 7d...

  • Page 386

    Default values 386 programming guide [605-606] outgoing permitted outside line assignment —— day / night all jacks-1/2 — all outside lines — enable —— day / night [607-608] doorphone ringing assignment — — day / night jack 01-1— all doorphones; other jacks — no doorphone —— day / night [609] voice m...

  • Page 387

    Default values programming guide 387 [710] t1 frame option c=a, d=b [711] t1 first dial timer (co) 02 [712] t1 first dial timer (did / tie) 002 [713] t1 %break 60% [714] t1 dial click tone yes [715] t1 inter digit pause 830 msec [716] t1 flash detection disable [717] t1 answer decision timer 001 [71...

  • Page 388

    Default values 388 programming guide [803] music source use hold and bgm — music 1 [804] external pager bgm all external pagers — disable [805] external pager confirmation tone on [806-807] serial interface (rs-232c) parameters new line code = cr+lf; baud rate = 9600; word length = 8; parity bit = m...

  • Page 389: Section

    Index 389 section 4 index.

  • Page 390

    Index 390 a absent messages 45 account code entry mode 262 account codes 64 adjust time 82 area code assignment 99 ars leading digit entry for plans 1 through 8 155 ars mode 152 ars modify added number 160 ars modify removed digit 159 ars routing plans 1 through 8 157 ars time 153 automatic access o...

  • Page 391

    Index 391 host pbx access codes 186 hotel application 114 i inter digit time 134 intercept extension —— day / night 184 intercept time 129 isdn class of service 284 isdn configuration 209 isdn data link mode 211 isdn extension clip number assignment 295 isdn extension multiple directory number 215 i...

  • Page 392

    Index 392 t1 did cpc (out) 302 t1 did receive digits 304 t1 extension cos number 330 t1 extension name 328 t1 extension number 327 t1 extension outgoing permitted outside line as- signment – day 332 t1 extension outgoing permitted outside line as- signment – night 334 t1 extension voice mail access ...

  • Page 393

    Index 393.

  • Page 394

    Index 394.

  • Page 395

    Index 395.

  • Page 396: 3Dqdvrqlf7Hohskrqh6\vwhpv

    Psqx2578ya ka0801hk2052 printed in the united kingdom this manual is copyrighted by kyushu matsushita electric co., ltd. (kme). Under the applicable copyright laws, this manual may not be reproduced in any form, in whole or part, without the prior written consent of kme and its licensee. 2001 kyushu...