DL manuals
Oki
Printer Accessories
C9600hdn
Installation Manual

Oki C9600hdn Installation Manual

Other manuals for C9600hdn: Configuration Manual, User Manual, Utility Manual, Network And Configuration Manual, Network And Configuration Manual, Safety And Regulatory Information Manual, Software Installation Manual, Regulatory And Safety Information Manual, Printing Manual, Reference Manual, Install Manual, User Manual, Configuration Manual, User Manual, Brochure & Specs, Troubleshooting Manual, Installation Instructions Manual, Installation Manual, Installation Manual

Manual is about: Guide: Network User's, OkiLAN 8200e

Page of 8

Download

Print this page

Bookmark us

Hole Punch Kit

(P/N 42872902)

Technician’s Installation Guide

1. Unpack the Hole Punch Kit and check the

contents:

[1] Hole Punch Unit

[2] Safety Labels

[3] Screw (for securing hole punch unit to finisher:

see step 14)

[4] Orange Cable (4 leads)

[5] Purple Cable (5 leads)

2. Remove the packing tape, blue spacers and

any other packing materials from the Hole

Punch Unit.

3. Turn off the printer.

4. On the back of the finisher/inverter unit,

unplug the inverter power cord (

) and the

connecting cord (

) to the finisher.

1 2 3 4 5 6 7 Next › »

Summary of C9600hdn

Page 1
Hole punch kit (p/n 42872902) technician’s installation guide 1. Unpack the hole punch kit and check the contents: [1] hole punch unit [2] safety labels [3] screw (for securing hole punch unit to finisher: see step 14) [4] orange cable (4 leads) [5] purple cable (5 leads) 2. Remove the packing tape,...
Page 2
2 5. Push in on the finisher release lever and slide the finisher away from the inverter. 6. Open the finisher front cover. 7. Squeeze the white locking tabs on the blue knob and pull it out of the finisher. 8. Remove the internal cover: a. Remove the two screws behind the cover. B. Remove the two s...
Page 3
3 9. Remove the screws securing the rear cover (two on the left side [ a ] and one on the right side [ b ]), then remove the rear cover. 10. Remove the two screws at either end of the hole punch blank. 11. Swing up the finisher top cover ( 1 ) and lift out the punch blank unit ( 2 ). A a b.
Page 4
4 12. Remove the top of the blank unit: you need this to install the hole punch unit. Store the bottom of the blank in case you ever remove the hole punch from the finisher. 13. Align the pins at either end of the hole punch unit with the holes in the finisher housing, then slide the hole punch unit...
Page 5
5 17. Insert the orange cable (4 leads) into the connector on the hole punch unit board. 18. Insert the purple cable (5 leads) into the connector on the hole punch unit board. 19. Snap open the four cable harnesses, then thread the two cables through the harnesses and snap each one shut. 20. Plug th...
Page 6
6 22. Reinstall the back cover and secure it in place: two screws on the left side (a ) and one screw on the right side ( b ). 23. Reinstall the internal front cover and secure it with four screws. A a b.
Page 7
7 24. Push the blue knob back into place. 25. Close the finisher front cover. 26. Apply the appropriate language safety label: 27. Slide the finisher back into the inverter. Make sure it locks in place. 28. Reattach the cable between the finisher and inverter and the finisher power cable. 29. Turn o...
Page 8
30. Test the operation of the hole punch unit: a. With a suitable document open in a software application, select [file] → [print]. B. Select the appropriate oki printer, then click [properties]. C. Click the [job options] tab. D. Under [finisher], [output bin], select [finisher(face-up)] or [finish...