DAELIM VJF125 Service Manual - Cylinder Removal
11-2
CYLINDER / PISTON
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-4
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder / head
mating surface. Do not scratch the surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 56.60 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder for out-of-round at three levels
in an X and Y axis. Take the maximum reading to
determine the out-of-round.
Calculate the cylinder for taper at three levels in an X
and Y axis. Take the maximum reading to determine
the taper.
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.05 mm
TAPER : 0.1 mm
CYLINDER REMOVAL
Remove the cylinder head. (
10-5
)
Remove the cylinder head gasket.
Remove the cam chain guide from the cylinder.
Remove the cylinder.
Remove the gasket and dowel pin. Carefully remove
any adhering gasket material from the cylinder mating
surface.
INSPECTION
Inspect the cylinder wall for scratches and wear.
Measure and record the cylinder inner diameter at
three levels in both an X and Y axis.
Take the maximum reading to determine the cylinder
wear.
SERVICE LIMIT : 73.005~73.015 mm
Measure the piston outer diameter.
Calculate the piston-to-cylinder clearance. Take the
maximum reading to determine the clearance.
SERVICE LIMIT : 0.30 mm
Calculate the cylinder roundness and cylinderical at
three levels in an X and Y axis. Take the maximum
reading to determine the roundness and cylinderical.
SERVICE LIMIT : ROUNDNESS : 0.05 mm
CYLINDERICAL : 0.1 mm
If any of the cylinder measurements exceed the service
limits, replace the cylinder.
SERVICE LIMIT : OUT-OF-ROUND : 0.2 mm , 0.50mm
: 0.75mm , 1.0mm
STANDARD LIMIT : 0.020~0.050 mm
If the piston outer diameter is oversize, boring the
cylinder to fit.
Take care not to damage the cylinder interface.
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
CYLINDER HEAD GASKET
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
PISTON
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
CYLINDER GAUGE
TOP
MIDDLE
BOTTOM