DAELIM VJF125 Service Manual - Transmission Assembly
12-9
CRANKCASE/TRANSMISSION/CRANKSHAFT
TRANSMISSION ASSEMBLY
Apply the gear and gear bush with clean engine oil
and install the main shaft and counter shaft.
Check the gears for freedom of movement or
rotation on the shaft.
Install the balancer gear.
Note the installation direction of each snap ring.
Do not use the worn snap ring again.
Check the snap rings are seated in the grooves
spinning the rings. Align the end gaps of the snap
ring with the grooves of spline.
Align the balancer drive gear and balancer driven
gear with the marking location.
C-1 GEAR
C-3 GEAR
MAIN SHAFT
M-3 GEAR
M-4 GEAR
M-5 GEAR
M-2 GEAR
C-4 GEAR
C-5 GEAR
C-2 GEAR
DRIVE SPROCKET
COUNTER TRANSMISSION SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
COUNTER SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
MAIN SHAFT
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVE GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
BALANCE DRIVEN GEAR
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION
ALIGN THE GEAR WITH THE MARKING LOCATION