1. DL manuals
  2. NEC
  3. Voicemail
  4. Univerge SV8100
  5. Programming Manual

NEC Univerge SV8100 Programming Manual

Other manuals for Univerge SV8100: Service Information Bulletin, Description, User Manual, User Manual, Quick Start User Manual, User Manual, Information Sheet, User Manual, System Specifications, Configuration Manual, User Manual, User Manual, Quick Reference Manual, Quick Reference Manual, General Description Manual, User Manual, System Maintenance Manual, User Manual, Features And Specifications Manual, Quick Manual, Features And Specifications Manual, Features And Specifications Manual, Features And Specifications Manual, Features And Specifications Manual, Features And Specifications Manual, Features And Specifications Manual, User Manual, Installation Manual, Installation Manual, Reference Manual, User Manual, System Hardware Manual, Reference sheet, Reference Sheet, Quick Start & Reference Manual, System Configuration Manual, User Manual, User Manual, Programming Manual, Administrator's Manual, User Manual, Quick Reference Manual, Quick Reference Manual, User Manual, User Manual, System Hardware Manual, Installation Manual, Condensed User's Manual, Installation Manual, Quick Reference Manual, System Hardware Manual, User Manual, Installation Manual, Administration Manual, Quick Reference Manual, System Hardware Manual, Features & Specifications Manual, Adminstrators Manual, System Hardware Manual, Programming Manual, Applications, System Hardware Manual, User Manual, Installation Manual, Reference Sheet

Summary of Univerge SV8100

  • Page 1

    Programming manual int-2041 (univ) issue 1.0 digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 2

    Nec unified solutions, inc. Reserves the right to change the specifications, functions, or features at any time without notice. Nec unified solutions, inc. Has prepared this document for use by its employees and customers. The information contained herein is the property of nec unified solutions, in...

  • Page 3: Preface

    Preface t his m anual the programming manual provides the technician with all of the necessary information for programming the univerge sv8100 system. Programming can be accomplished using a pc or a multiline terminal. S upporting d ocuments univerge sv8100 general description manual this manual pro...

  • Page 4

    ___________________________________________________________________________________ ii table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 10-14 : managed network setup ..........................................................

  • Page 5

    Univerge sv8100 issue 1.0 programming manual iii ___________________________________________________________________________________ ___________________________________________________________________________________ 10-56 : xml portal ip phone ..........................................................

  • Page 6

    ___________________________________________________________________________________ iv table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 13-04 : speed dialing number and name ......................................... 2-124...

  • Page 7

    Univerge sv8100 issue 1.0 programming manual v ___________________________________________________________________________________ ___________________________________________________________________________________ 15-14 : programmable one-touch keys ........................................... 2-188...

  • Page 8

    ___________________________________________________________________________________ vi table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 20-20 : message setup for non-caller id data ................................. 2-240 ...

  • Page 9

    Univerge sv8100 issue 1.0 programming manual vii ___________________________________________________________________________________ ___________________________________________________________________________________ 21-18 : ip trunk (h.323) calling party number setup for extension ....................

  • Page 10

    ___________________________________________________________________________________ viii table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 24-02 : system options for transfer ..................................................

  • Page 11

    Univerge sv8100 issue 1.0 programming manual ix ___________________________________________________________________________________ ___________________________________________________________________________________ 30-02 : dss console extension assignment .................................... 2-360 ...

  • Page 12

    ___________________________________________________________________________________ x table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 34-09 : ani/dnis service options .................................................... ...

  • Page 13

    Univerge sv8100 issue 1.0 programming manual xi ___________________________________________________________________________________ ___________________________________________________________________________________ 41-10 : aci delay announcement ........................................................

  • Page 14

    ___________________________________________________________________________________ xii table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 program 45 : voice mail integration 45-01 : voice mail integration options ............

  • Page 15

    Univerge sv8100 issue 1.0 programming manual xiii ___________________________________________________________________________________ ___________________________________________________________________________________ 50-09 : ccis centralized blf sending extension number assignment ....................

  • Page 16

    ___________________________________________________________________________________ xiv table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 80-05 : date format for smdr and system ...................................... 2-595...

  • Page 17

    Univerge sv8100 issue 1.0 programming manual xv ___________________________________________________________________________________ ___________________________________________________________________________________ 84-07 : firmware download setup .......................................................

  • Page 18

    ___________________________________________________________________________________ xvi table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 90-11 : system alarm report ...........................................................

  • Page 19

    Univerge sv8100 issue 1.0 programming manual xvii ___________________________________________________________________________________ ___________________________________________________________________________________ 90-57 : backup recovery data ........................................................

  • Page 20

    ___________________________________________________________________________________ xviii table of contents ___________________________________________________________________________________ issue 1.0 univerge sv8100 this page intentionally left blank digitcom canada inc. Need support? Call 1-866-6...

  • Page 21

    Programming manual xix ___________________________________________________________________________________ ___________________________________________________________________________________ list of tables table 1-1 keys for entering data ................................................................

  • Page 22

    ___________________________________________________________________________________ xx list of tables ___________________________________________________________________________________ issue 1.0 univerge sv8100 this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-835...

  • Page 23: Tio

    Programming manual 1 - 1 in tr o d u c tio n 1 introduction s ection 1 b efore y ou s tart p rogramming this chapter provides you with detailed information about the system programs. By changing a program, you change the way the feature associated with that program works. In this chapter, you find o...

  • Page 24

    Issue 1.0 univerge sv8100 1 - 2 introduction feature cross reference provides you with a table of all the features affected by the program. You will want to keep the referenced features in mind when you change a program. Customizing a feature may have an effect on another feature that you did not in...

  • Page 25

    Univerge sv8100 issue 1.0 programming manual 1 - 3 s ection 4 h ow to e xit p rogramming m ode to exit the programming mode: when you are done programming, you must be out of a program option to exit (pressing the answer key will exit the program option). 1. Press answer key to exit the program opti...

  • Page 26

    Issue 1.0 univerge sv8100 1 - 4 introduction s ection 5 u sing k eys to m ove a round in the p rograms once you enter the programming mode, use the keys in the following chart to enter data, edit data and move around in the menus. Table 1-1 keys for entering data keys for entering data use this key....

  • Page 27

    Univerge sv8100 issue 1.0 programming manual 1 - 5 s ection 6 p rogramming n ames and t ext m essages several programs (e.G., program 20-16 : selectable display messages) require you to enter text. Use the following chart when entering and editing text. When using the keypad digits, press the key on...

  • Page 28

    Issue 1.0 univerge sv8100 1 - 6 introduction s ection 7 u sing s oftkeys f or p rogramming each univerge sv8100 display telephone provides interactive softkeys for intuitive feature access. The options for these keys will automatically change depending on where you are in the system programming. Sim...

  • Page 29

    Univerge sv8100 issue 1.0 programming manual 1 - 7 s ection 8 w hat the s oftkey d isplay p rompts m ean when using a display telephone in programming mode, various softkey options are displayed. These keys will allow you to easily select, scan, or move through the programs. Table 1-3 softkey displa...

  • Page 30

    Issue 1.0 univerge sv8100 1 - 8 introduction s ection 9 s ystem n umber p lan /c apacities the following table provides the capacities for the univerge sv8100 system. Table 1-4 system number plan/capacities system number plan/capacities system type number plan/capacities system analog caller id dete...

  • Page 31

    Univerge sv8100 issue 1.0 programming manual 1 - 9 extension telephone extension ports p multiline terminals p single line phones/analog devices p voip extensions p sip dect wireless 512 256 256 512 504 dlca: p physical ports 01~16 lca: p physical ports 01~16 telephone extension number range 1~89999...

  • Page 32

    Issue 1.0 univerge sv8100 1 - 10 introduction speed dialing speed dialing groups 64 speed dialing bins 0~1999 speed dialing table-common 1000 acd acd groups 64 acd agent extensions 512 aci aci groups 16 aci ports 96 automated attendant vrs message numbers 1~100 conference conference circuits 64 - ma...

  • Page 33

    Univerge sv8100 issue 1.0 programming manual 1 - 11 paging and park internal page group numbers 0, 01~64 external page group numbers 0, 1~8 external speakers p cd-cp00-us( )-u10 p pgd(2)-u10 adp 9 (1) (1~8) park group numbers 1~64 park orbits 1~64 smdr smdr ports 1~8 vrs/vm8000 inmail vrs/vm8000 inm...

  • Page 34

    Issue 1.0 univerge sv8100 1 - 12 introduction level 3 (sa) pcpro/webpro user name: 0000 admin1 level 4 (sb) pcpro/webpro user name: 9999 admin2 programming password users 8 footnotes extension numbers can be one to eight digits long. Refer to the flexible system numbering feature in the univerge sv8...

  • Page 35

    Programming manual 2 - 1 p ro g ra m m in g t h e u n iv e r g e s v 8 1 0 0 2 programming the univerge sv8100 s ection 1 p rogramming y our s ystem the information contained in this chapter provides the information necessary to properly program your univerge univerge sv8100 system. The programming ...

  • Page 36

    Issue 1.0 univerge sv8100 2 - 2 programming the univerge sv8100 program 31 : paging setup program 32 : door box and sensor setup program 33 : cta and aci setup program 34 : tie line setup program 35 : smdr account code setup program 40 : voice recording system program 41 : acd setup program 42 : hot...

  • Page 37: 10-01 : Time And Date

    Programming manual 2 - 3 program 10 description use program 10-01 : time and date to change the system time and date through system programming. Extension users can also dial service code 728 to change the time if allowed by an extension class of service. Conditions none feature cross reference r cl...

  • Page 38: 10-02 : Location Setup

    Issue 1.0 univerge sv8100 2 - 4 program 10 : system configuration setup description use program 10-02 : location setup to define the location of the installed system. Conditions none feature cross reference none program 10 : system configuration setup 10-02 : location setup level: sa input data item...

  • Page 39: 10-03 : Etu Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 5 description use program 10-03 : etusetup to setup and confirm the basic configuration data for each blade. When changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automatically define it or y...

  • Page 40

    Issue 1.0 univerge sv8100 2 - 6 program 10 : system configuration setup 02 logical port number (b1) 0 = not set 1 = multiline terminal (1~256) 2 = slt adapter (1~256) 6 = pgd(2)-u10 adp (paging) (1~8) 7 = pgd(2)-u10 adp (for tone ringer) (1~8) 8 = pgd(2)-u10 adp (for door box) (1~8) 9 = pgd(2)-u10 a...

  • Page 41

    Univerge sv8100 issue 1.0 programming manual 2 - 7 for lca pkg setup for cota unit setup 08 multiline telephone type 0 = dt3** 1 = d term 8 2 = d term 7 0 09 side option information 0 = no option 1 = 8lk unit 2 = 16lk unit 3 = 24adm 0 10 bottom option information (only applies to dtl–style telephone...

  • Page 42

    Issue 1.0 univerge sv8100 2 - 8 program 10 : system configuration setup for odta pkg setup for diop pkg setup physical port number 01~04 item no. Item input data default 01 logical port number 0~200 0 02 2/4 wire 0 = 2 wire 1 = 4 wire 1 03 e&m line control method 0 = type i 1 = type v 0 physical por...

  • Page 43

    Univerge sv8100 issue 1.0 programming manual 2 - 9 for bria pkg setup isdn line number 01~04 item no item input data default 01 isdn line mode 0 = not used 1 = t-point 1 02 logical port number the starting port number of a bri line is displayed. Two logic ports are automatically assigned to a bri li...

  • Page 44

    Issue 1.0 univerge sv8100 2 - 10 program 10 : system configuration setup 18 type of number isdn protocol definition 0 = unknown 1 = international number 2 = national number 3 = network specific number 4 = subscriber number 5 = abbreviated number 2 19 numbering plan identification isdn protocol defin...

  • Page 45

    Univerge sv8100 issue 1.0 programming manual 2 - 11 for prta pkg setup isdn line number 01~24 item no. Item input data default 01 --- not used --- 02 logical port number the start port number of a pri line is displayed. 1 = for t-bus 1~200 1 03 --- not used --- 04 layer 3 timer type each timer value...

  • Page 46

    Issue 1.0 univerge sv8100 2 - 12 program 10 : system configuration setup 13 loss-of-signal detection limit if the transmit/receive voltage is less than the setting in 10-03-13, the system considers this as loss-of-signal and the prta does not come up. Note that there are different values based on th...

  • Page 47

    Univerge sv8100 issue 1.0 programming manual 2 - 13 for dti (t1) pkg setup 22 --- not used --- 23 straight/cross wiring 0 = auto 1 = manual (cross) 2 = manual (straight) 0 physical port number 01~24 item no. Item input data default 01 logical port number the start port number of a t1 line is display...

  • Page 48

    Issue 1.0 univerge sv8100 2 - 14 program 10 : system configuration setup for ipla pkg setup for vm00 pkg setup for ccta pkg setup physical port number 001~128 item no. Item input data default 01 trunk logical port number 0~200 0 02 trunk type 0 = h.323 1 = sip 1 03 ccis trunk 0 = not ccis 1 = ccis 0...

  • Page 49

    Univerge sv8100 issue 1.0 programming manual 2 - 15 conditions p when changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automatically define it, or redefine the type manually. P the system must have a blade installed to view/change the optio...

  • Page 50

    Issue 1.0 univerge sv8100 2 - 16 program 10 : system configuration setup description use program 10-04 : music on hold setup to set the music on hold (moh) source. For internal music on hold, the system can provide a service tone callers on hold or one of eleven synthesized selections. Program 10 : ...

  • Page 51

    Univerge sv8100 issue 1.0 programming manual 2 - 17 conditions none feature cross reference r analog communications interface (aci) r background music r music on hold digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 52

    Issue 1.0 univerge sv8100 2 - 18 program 10 : system configuration setup description use program 10-05 : general purpose relay setup to define which relay circuits (5~8) on pgd(2)-u10 adp are used for general purpose relay. Input data conditions none feature cross reference r analog communications i...

  • Page 53: 10-06 : Isdn-Bri Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 19 description use program 10-06 : isdn - bri setup to configure the isdn - bri terminal endpoint identifier (tei), mode of operation, and service profile identifier (spid) number for each circuit b-channels. Conditions none feature cross reference r ...

  • Page 54: 10-08 : Pre-Ringing Setup

    Issue 1.0 univerge sv8100 2 - 20 program 10 : system configuration setup description use program 10-08 : pre-ringing setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk led flashes...

  • Page 55

    Univerge sv8100 issue 1.0 programming manual 2 - 21 description use program 10-09 : dtmf and dial tone circuit setup to allocate the circuits on the cd-cp00-us for either dtmf receiving or dial tone detection. The cd-cp00-us has 32 circuits initially, and an addition 64 circuits are added when a pz-...

  • Page 56

    Issue 1.0 univerge sv8100 2 - 22 program 10 : system configuration setup description use program 10-12 : cd-cp00-us network setup to setup the ip address, subnet-mask, and default gateway addresses. Caution! If any ip address or nic settings are changed, the system must be reset for the changes to t...

  • Page 57

    Univerge sv8100 issue 1.0 programming manual 2 - 23 04 time zone 0~24 (0 = -12 hours and 24 = +12 hours) +7 (-5 hours) determine the offset from greenwich mean time (gmt) time. Then enter its respective value. For example, eastern time (us and canada) has a gmt offset of -5. The program data would t...

  • Page 58

    Issue 1.0 univerge sv8100 2 - 24 program 10 : system configuration setup conditions p the system must be reset for these changes to take affect. Feature cross reference r voice over internet protocol (voip) 10 subnet mask 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0....

  • Page 59

    Univerge sv8100 issue 1.0 programming manual 2 - 25 description use program 10-13 : in-dhcp server setup to setup the dhcp server built into the cd-cp00-us blade. Conditions none feature cross reference r voice over internet protocol (voip) program 10 : system configuration setup 10-13 : in-dhcp ser...

  • Page 60

    Issue 1.0 univerge sv8100 2 - 26 program 10 : system configuration setup description use program 10-14 : managed network setup to set up the range of the ip address which the dhcp server leases to a client. Conditions none feature cross reference r voice over internet protocol (voip) program 10 : sy...

  • Page 61

    Univerge sv8100 issue 1.0 programming manual 2 - 27 description use program 10-15 : client information setup to set up the client information when the dhcp server needs to assign a fixed ip address to clients. Conditions none feature cross reference r voice over internet protocol (voip) program 10 :...

  • Page 62

    Issue 1.0 univerge sv8100 2 - 28 program 10 : system configuration setup description use program 10-16 : option information setup to set up the option given from the dhcp server to each client. Program 10 : system configuration setup 10-16 : option information setup level: sa input data item no. Ite...

  • Page 63

    Univerge sv8100 issue 1.0 programming manual 2 - 29 08 download protocol set download protocol used for autoconfig (for dt700 series). Code number 0~255 43 (fixed) sub code number 163 1 = ftp 2 = http 1 09 encryption information set an encryption information used for autoconfig (for dt700 series). C...

  • Page 64

    Issue 1.0 univerge sv8100 2 - 30 program 10 : system configuration setup 17 sip server (domain name) code number 0~255 120 (fixed) maximum 20 character strings no setting 18 ftp server code number 0~255 141 (fixed) ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255....

  • Page 65

    Univerge sv8100 issue 1.0 programming manual 2 - 31 conditions none feature cross reference r voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 66

    Issue 1.0 univerge sv8100 2 - 32 program 10 : system configuration setup description use program 10-17 : h.323 gatekeeper setup to set the h.323 gatekeeper information. Conditions none feature cross reference r ip trunk – h.323 program 10 : system configuration setup 10-17 : h.323 gatekeeper setup l...

  • Page 67

    Univerge sv8100 issue 1.0 programming manual 2 - 33 description use program 10-18 : h.323 alias address setup to set the alias address registered to the outside h.323 gatekeeper. Conditions none feature cross reference r ip trunk – h.323 program 10 : system configuration setup 10-18 : h.323 alias ad...

  • Page 68

    Issue 1.0 univerge sv8100 2 - 34 program 10 : system configuration setup description use program 10-19 : voip dsp resource selection to define the criteria for each dsp resource on the voip blade. Conditions none feature cross reference r none program 10 : system configuration setup 10-19 : voip dsp...

  • Page 69

    Univerge sv8100 issue 1.0 programming manual 2 - 35 description use program 10-20 : lan setup for external equipment to define the tcp port/ address/etc. For communicating to external equipment. Program 10 : system configuration setup 10-20 : lan setup for external equipment level: in input data typ...

  • Page 70

    Issue 1.0 univerge sv8100 2 - 36 program 10 : system configuration setup conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 71

    Univerge sv8100 issue 1.0 programming manual 2 - 37 description use program 10-21 : cd-cp00-us hardware setup to set up various hardware, such as the baud rate of com port and the switch for control on cd-cp00-us blade. Conditions none feature cross reference none program 10 : system configuration s...

  • Page 72

    Issue 1.0 univerge sv8100 2 - 38 program 10 : system configuration setup description use program 10-23 : sip system interconnection setup to determine if the system is interconnected and define the ip address of another system, call control port number and alias address for sv8100 system interconnec...

  • Page 73

    Univerge sv8100 issue 1.0 programming manual 2 - 39 description use program 10-24 : daylight savings setup to set the options for daylight savings. As the telephone system is used globally, these settings define when the system should automatically adjust for daylight savings as it applies to the re...

  • Page 74

    Issue 1.0 univerge sv8100 2 - 40 program 10 : system configuration setup conditions none feature cross reference r clock/calendar display 08 end of week day enter the day of the week when the system should adjust the time for daylight savings time (01 = sunday, 02 = monday, etc.). 1~7 (sun = 1, mon ...

  • Page 75

    Univerge sv8100 issue 1.0 programming manual 2 - 41 description use program 10-25 : h.323 gateway prefix setup to set the gateway prefix registered to the outside gatekeeper. Conditions none feature cross reference none program 10 : system configuration setup 10-25 : h.323 gateway prefix setup level...

  • Page 76

    Issue 1.0 univerge sv8100 2 - 42 program 10 : system configuration setup description use program 10-26 : ip system operation setup to enable or disable the peer to peer feature for sip mlt and sip ip stations. Conditions p disabling 10-26-01 will result in sip mlt station-to- sip mlt station calls u...

  • Page 77

    Univerge sv8100 issue 1.0 programming manual 2 - 43 description use program 10-28 : sip system information setup to set up basic sip trunking. Program 10 : system configuration setup 10-28 : sip system information setup level: in input data item no. Item input data default 01 domain name this sets t...

  • Page 78

    Issue 1.0 univerge sv8100 2 - 44 program 10 : system configuration setup conditions none feature cross reference none 05 domain assignment if the information from telco was a domain name (siptrunk@sip.Com) then set to domain. If the information for telco was a ip address then set to ip address. 0 = ...

  • Page 79

    Univerge sv8100 issue 1.0 programming manual 2 - 45 description use program 10-29 : sip server information setup to define the sip proxy setup for outbound/inbound. The 10-29 commands are not used in non-registration mode. If entries are made in program 10-29-xx for a sip server and the sip server i...

  • Page 80

    Issue 1.0 univerge sv8100 2 - 46 program 10 : system configuration setup 04 default proxy port number the port number of the default proxy is set. 0 ~ 65535 5060 05 registrar mode the mode registered in the registration server is set. 0 = none 1 = manual 0 06 registrar ip address ip address of the s...

  • Page 81

    Univerge sv8100 issue 1.0 programming manual 2 - 47 conditions none feature cross reference none 14 sip carrier choice this selects the carrier type of the sip server. 0 ~ 7 0 = standard 1 = carrier a 2 = carrier b 3 = carrier c 4 = carrier d 5 = carrier e 6 = carrier f 7 = carrier g 0 15 registrati...

  • Page 82

    Issue 1.0 univerge sv8100 2 - 48 program 10 : system configuration setup description use program 10-30 : sip authentication information setup to set the authentication options for sip trunks. Conditions none feature cross reference none program 10 : system configuration setup 10-30 : sip authenticat...

  • Page 83

    Univerge sv8100 issue 1.0 programming manual 2 - 49 description use program 10-33 : sip registrar/proxy information basic setup to set the registrar/proxy options for sip extensions. Program 10 : system configuration setup 10-33 : sip registrar/proxy information basic setup level: in input data item...

  • Page 84

    Issue 1.0 univerge sv8100 2 - 50 program 10 : system configuration setup conditions none feature cross reference none 04 registrar/proxy host name this sets the domain name of the sip proxy. Up to 48 characters none input data digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.D...

  • Page 85

    Univerge sv8100 issue 1.0 programming manual 2 - 51 description use program 10-36 : sip trunk registration information setup to set the sip trunk registration information. Conditions none feature cross reference none program 10 : system configuration setup 10-36 : sip trunk registration information ...

  • Page 86: 10-37 : Upnp Setup

    Issue 1.0 univerge sv8100 2 - 52 program 10 : system configuration setup description use program 10-37 : upnp setup to set the upnp (universal plug and play) options for sip trunks. Conditions none feature cross reference none program 10 : system configuration setup 10-37 : upnp setup level: in inpu...

  • Page 87

    Univerge sv8100 issue 1.0 programming manual 2 - 53 description use program 10-38 : bgm resource setup to configure the background music source input. Conditions none feature cross reference r analog communications interface (aci) r background music program 10 : system configuration setup 10-38 : bg...

  • Page 88: 10-39 : Fractional Setup

    Issue 1.0 univerge sv8100 2 - 54 program 10 : system configuration setup description use program 10-39 : fractional setup to enable or disable the ability to use fractional t1 or pri. Conditions none feature cross reference none program 10 : system configuration setup 10-39 : fractional setup level:...

  • Page 89

    Univerge sv8100 issue 1.0 programming manual 2 - 55 description use program 10-40 : ip trunk availability to enable or disable the ability to use sip trunks and assign the number of ports if ip trunk is enabled. Conditions none feature cross reference none program 10 : system configuration setup 10-...

  • Page 90

    Issue 1.0 univerge sv8100 2 - 56 program 10 : system configuration setup description use program 10-42 : virtual loop back port setting to set the data for the virtual loop back port. Conditions none feature cross reference none program 10 : system configuration setup 10-42 : virtual loop back port ...

  • Page 91

    Univerge sv8100 issue 1.0 programming manual 2 - 57 description use program 10-45 : ip routing table setup to set up the ip routing table. Conditions none feature cross reference none program 10 : system configuration setup 10-45 : ip routing table setup level: in input data routing table number 001...

  • Page 92

    Issue 1.0 univerge sv8100 2 - 58 program 10 : system configuration setup description use program 10-46 : dt700 server information setup to setup the information of sip multiline (dt700 series) server. Program 10 : system configuration setup 10-46 : dt700 server information setup level: in input data...

  • Page 93

    Univerge sv8100 issue 1.0 programming manual 2 - 59 conditions none feature cross reference none 06 register port assign the port number in which the sip messages are sent to on the ipla. This same port number must be assigned in the sip multiline terminals. If this command is changed, it requires a...

  • Page 94

    Issue 1.0 univerge sv8100 2 - 60 program 10 : system configuration setup description use program 10-47 : terminal license server information setup to setup the information of terminal license server. Conditions none feature cross reference none program 10 : system configuration setup 10-47 : termina...

  • Page 95

    Univerge sv8100 issue 1.0 programming manual 2 - 61 description use program 10-48 : license activation to turn on the license issued from the license server. Conditions none feature cross reference none program 10 : system configuration setup 10-48 : license activation level: in input data item no. ...

  • Page 96

    Issue 1.0 univerge sv8100 2 - 62 program 10 : system configuration setup description use program 10-49 : license file activation to enable the command to save the license file via usb memory which is issued from the license server. Conditions none feature cross reference none program 10 : system con...

  • Page 97

    Univerge sv8100 issue 1.0 programming manual 2 - 63 description use program 10-50 : license information to confirm license information that is stored in a system. Program 10 : system configuration setup 10-50 : license information level: in input data item no. Item read data 01 license name none 02 ...

  • Page 98

    Issue 1.0 univerge sv8100 2 - 64 program 10 : system configuration setup refer to the following table to assist with licensing information. Table 2-2 license information license code license name reset required min max note 0001 712 port yes on/off 0002 netlink yes 1 49 0007 hotel/motel (pms) yes on...

  • Page 99

    Univerge sv8100 issue 1.0 programming manual 2 - 65 2103 acd-mis add.Monit 1 4 2104 acd-mis agent 1 197 2105 acd-mis xml manag 1 200 3000 ca-basic on/off 3001 ca-256 station on/off 3002 ca-up 20 to 256 on/off 3003 ca-network client 1 999 3004 ca- addremote site 1 999 3005 ca- remotesiteso ft 1 999 3...

  • Page 100

    Issue 1.0 univerge sv8100 2 - 66 program 10 : system configuration setup conditions p confirm license by entering feature code no. (0~9999) feature cross reference none 5303 softphone enhance 1 128 5304 attendant 1 128 5305 assistant 1 128 6000 pva-conf port 1 16 6101 pva-ivr port 1 16 table 2-2 lic...

  • Page 101

    Univerge sv8100 issue 1.0 programming manual 2 - 67 description use program 10-51 : pri/t1 selection of cd-prta to select whether the cd-prta works as pri or t1. Conditions none feature cross reference none program 10 : system configuration setup 10-51 : pri/t1 selection of cd-prta level: in input d...

  • Page 102

    Issue 1.0 univerge sv8100 2 - 68 program 10 : system configuration setup description use program 10-52 : free/demo license information to display information on free of charge/demo license. Conditions none feature cross reference none program 10 : system configuration setup 10-52 : free/demo license...

  • Page 103

    Univerge sv8100 issue 1.0 programming manual 2 - 69 description use program 10-54 : license configuration for each package to set the license information for each unit. Conditions none feature cross reference none program 10 : system configuration setup 10-54 : license configuration for each package...

  • Page 104

    Issue 1.0 univerge sv8100 2 - 70 program 10 : system configuration setup description use program 10-55 : package network setup to set the network information for each unit. This program sets the spoe of each package. Program 10 : system configuration setup 10-55 : package network setup level: in inp...

  • Page 105

    Univerge sv8100 issue 1.0 programming manual 2 - 71 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 106

    Issue 1.0 univerge sv8100 2 - 72 program 10 : system configuration setup description use program 10-56 : xml portal ip phone to set the contents of xml portal page provided to the ip phone. The xml portal page is included in the xml application name and url link information. Xml url link information...

  • Page 107: 11-01 : System Numbering

    Programming manual 2 - 73 program 11 description use program 11-01 : system numbering to set the system numbering plan. The numbering plan assigns the first and second digits dialed and affects the digits an extension user must dial to access other extensions and features, such as service codes and ...

  • Page 108

    Issue 1.0 univerge sv8100 2 - 74 program 11 : system numbering r entering two digits lets you define codes based on the first two digits a user dials. For example, entering 60 allows you to define the function of all codes beginning with 60. In the default program, only 4 and # use 2-digit codes. Al...

  • Page 109

    Univerge sv8100 issue 1.0 programming manual 2 - 75 default see the following tables for default settings. 9 dial extension analyze 11-20 : dial extension analyze table changing the dial type for a range of codes can have a dramatic affect on how your system operates. Assume, for example, the site i...

  • Page 110

    Issue 1.0 univerge sv8100 2 - 76 program 11 : system numbering 27 0 0 28 0 0 29 0 0 20 0 0 2 4 0 0 2 # 0 0 3x 4 2 31 0 0 32 0 0 33 0 0 34 0 0 35 0 0 36 0 0 37 0 0 38 0 0 39 0 0 30 0 0 3 4 0 0 3 # 0 0 4x 3 1 41 0 0 42 0 0 43 0 0 44 0 0 45 0 0 46 0 0 47 0 0 48 0 0 49 0 0 table 2-3 system numbering def...

  • Page 111

    Univerge sv8100 issue 1.0 programming manual 2 - 77 40 0 0 4 4 0 0 4 # 0 0 5x 3 1 51 0 0 52 0 0 53 0 0 54 0 0 55 0 0 56 0 0 57 0 0 58 0 0 59 0 0 50 0 0 5 4 0 0 5 # 0 0 6x 3 1 61 0 0 62 0 0 63 0 0 64 0 0 65 0 0 66 0 0 67 0 0 68 0 0 69 0 0 60 0 0 6 4 0 0 6 # 0 0 table 2-3 system numbering default sett...

  • Page 112

    Issue 1.0 univerge sv8100 2 - 78 program 11 : system numbering 7x 3 1 71 0 0 72 0 0 73 0 0 74 0 0 75 0 0 76 0 0 77 0 0 78 0 0 79 0 0 70 0 0 7 4 0 0 7 # 0 0 8x 1 1 81 0 0 82 0 0 83 0 0 84 0 0 85 0 0 86 0 0 87 0 0 88 0 0 89 0 0 80 0 0 8 4 0 0 8 # 0 0 9x 1 3 91 0 0 92 0 0 table 2-3 system numbering def...

  • Page 113

    Univerge sv8100 issue 1.0 programming manual 2 - 79 93 0 0 94 0 0 95 0 0 96 0 0 97 0 0 98 0 0 99 0 0 90 0 0 9 4 0 0 9 # 0 0 0x 1 5 01 0 0 02 0 0 03 0 0 04 0 0 05 0 0 06 0 0 07 0 0 08 0 0 09 0 0 00 0 0 0 4 0 0 0 # 0 0 4 x 2 1 4 1 0 0 4 2 0 0 4 3 0 0 4 4 0 0 4 5 0 0 table 2-3 system numbering default ...

  • Page 114

    Issue 1.0 univerge sv8100 2 - 80 program 11 : system numbering conditions none feature cross reference r flexible system numbering 4 6 0 0 4 7 0 0 4 8 0 0 4 9 0 0 4 0 0 0 44 0 0 4 # 0 0 # x 0 0 # 1 2 1 # 2 2 1 # 3 2 1 # 4 2 1 # 5 2 1 # 6 2 1 # 7 2 1 # 8 2 1 # 9 2 1 # 0 2 1 # 4 4 1 ## 2 1 table 2-3 s...

  • Page 115

    Univerge sv8100 issue 1.0 programming manual 2 - 81 description use program 11-02 : extension numbering to set the extension number. The extension number can have up to eight digits. The first/second digit(s) of the number should be assigned in program 11-01 or program 11-20. This allows an employee...

  • Page 116

    Issue 1.0 univerge sv8100 2 - 82 program 11 : system numbering conditions none feature cross reference r department calling r flexible system numbering r intercom digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 117

    Univerge sv8100 issue 1.0 programming manual 2 - 83 description use program 11-04 : virtual extension numbering to define the virtual extension numbers. The extension number can have up to eight digits. The first/second digit(s) of the number should be assigned in program 11-01 or program 11-20. Def...

  • Page 118

    Issue 1.0 univerge sv8100 2 - 84 program 11 : system numbering conditions none feature cross reference r flexible system numbering r multiple directory numbers / call coverage digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 119

    Univerge sv8100 issue 1.0 programming manual 2 - 85 description use program 11-06 : aci extension numbering to define the virtual extension number to be used for the aci. The extension number can have up to eight digits. The first and second digits of the number should be assigned in program 11-01 o...

  • Page 120

    Issue 1.0 univerge sv8100 2 - 86 program 11 : system numbering description use program 11-07 : department group pilot numbers to assign pilot numbers to each department group set up in program 16-02. The pilot number is the number users dial for department calling and department step calling. The pi...

  • Page 121

    Univerge sv8100 issue 1.0 programming manual 2 - 87 description use program 11-08 : aci group pilot number to assign the pilot number to the aci groups set in program 33-02. The pilot number can have up to four digits. The first and second digits of the number should be assigned in program 11-01 or ...

  • Page 122

    Issue 1.0 univerge sv8100 2 - 88 program 11 : system numbering description use program 11-09 : trunk access code to assign the trunk access code (normally 9). The trunk access code can be set from 1~8 digits which is defined to type 3 and 4 in program 11-01. This is the code extension users dial to ...

  • Page 123

    Univerge sv8100 issue 1.0 programming manual 2 - 89 conditions none feature cross reference r automatic route selection r central office calls, placing r trunk group routing 02 2nd trunk route access code use this program to define additional trunk access codes. When a user dials the alternate trunk...

  • Page 124

    Issue 1.0 univerge sv8100 2 - 90 program 11 : system numbering description use program 11-10 : service code setup (for system administrator) to customize the service codes for the system administrator. You can customize additional service codes in programs 11-11~11-16. The following chart shows: r t...

  • Page 125

    Univerge sv8100 issue 1.0 programming manual 2 - 91 12 night mode switching for other group mlt 618 12-xx 20-07-01 13 --- not used --- 14 --- not used --- 15 --- not used --- 16 leaving message waiting (requires cpu to be licensed for hotel/motel) mlt 626 11-11-09 17 dial block by supervisor mlt 601...

  • Page 126

    Issue 1.0 univerge sv8100 2 - 92 program 11 : system numbering conditions none feature cross reference r refer to input data chart on the previous pages. 36 change the guidance message number on voice mail auto attendant mlt, slt not set 41 date setting mlt not set 20-07-30 42 maintenance service ml...

  • Page 127

    Univerge sv8100 issue 1.0 programming manual 2 - 93 description use program 11-11 : service code setup (for setup/entry operation) to customize the service codes which are used for registration and setup. You can customize additional service codes in programs 11-10, and 11-12 ~ 11-16. The following ...

  • Page 128

    Issue 1.0 univerge sv8100 2 - 94 program 11 : system numbering 14 text message setting mlt no setting 15 enable handsfree incoming intercom calls mlt 721 20-09-05 20-02-12 16 force ringing of incoming intercom calls mlt 723 20-09-05 20-02-12 17 programmable function key programming (2-digit service ...

  • Page 129

    Univerge sv8100 issue 1.0 programming manual 2 - 95 37 ring volume set mlt 729 38 programmable function key programming (3-digit service codes) mlt 752 15-07 11-11-17 39 station speed dial number entry mlt, slt 755 40 --- not used --- 41 tandem ringing mlt, slt no setting 15-07 30-03 42 --- not used...

  • Page 130

    Issue 1.0 univerge sv8100 2 - 96 program 11 : system numbering conditions none feature cross reference r refer to the input data chart above. 58 call forward with personal greeting mlt, slt 713 59 call forward to attendant except busy mlt, slt no setting 15-01-08 60 call forward to attendant/no answ...

  • Page 131

    Univerge sv8100 issue 1.0 programming manual 2 - 97 description use program 11-12 : service code setup (for service access) to customize the service codes which are used for service access. You can customize additional service codes in programs 11-10, 11-11, and 11-13 through 11-16. The following ch...

  • Page 132

    Issue 1.0 univerge sv8100 2 - 98 program 11 : system numbering 11 group speed dialing mlt, slt # 4 12 last number dial mlt, slt # 5 13 saved number dial mlt, slt 715 14 trunk group access mlt, slt 704 15 specified trunk access mlt, slt # 9 16 trunk access via networking mlt, slt no setting 17 clear ...

  • Page 133

    Univerge sv8100 issue 1.0 programming manual 2 - 99 38 general purpose indication mlt 783 15-07-56 15-07-57 39 --- not used --- 40 station speed dialing mlt, slt # 7 41 voice over mlt 690 11-16-08 42 flash on trunk lines slt # 3 43 answer no-ring line (universal answer) mlt, slt # 0 14-05 14-06 44 c...

  • Page 134

    Issue 1.0 univerge sv8100 2 - 100 program 11 : system numbering conditions none feature cross reference r refer to the input data chart on the previous pages. 59 trunk drop operation for slt slt no setting mlt = multiline terminal slt = single line telephone input data (continued) item no. Item term...

  • Page 135

    Univerge sv8100 issue 1.0 programming manual 2 - 101 description use program 11-13 : service code setup (for acd) to customize the service codes which are used with the automatic call distribution (acd) feature. You can customize additional service codes in programs 11-10 ~ 11-12 and 11-14 ~ 11-16. ...

  • Page 136

    Issue 1.0 univerge sv8100 2 - 102 program 11 : system numbering conditions none feature cross reference r automatic call distribution (acd) 12 change agent acd group by supervisor when using service code 669 to change an agent acd group, the supervisor must enter a 2-digit number for the group. For ...

  • Page 137

    Univerge sv8100 issue 1.0 programming manual 2 - 103 description use program 11-14 : service code setup (for hotel) to customize the service codes which are used with the hotel/motel feature. You can customize additional service codes in programs 11-10 ~ 11-13, 11-15 and 11-16. The service codes can...

  • Page 138

    Issue 1.0 univerge sv8100 2 - 104 program 11 : system numbering conditions none feature cross reference r hotel/motel 14 room status change for own extension mlt, slt 640 15 room status change for other extension mlt, slt 641 16 room status output mlt 642 17 hotel room monitor mlt, slt 675 18 set ho...

  • Page 139

    Univerge sv8100 issue 1.0 programming manual 2 - 105 description use program 11-15 : service code setup, administrative (for special access) to customize the special access service codes which are used by the administrator in the hotel/motel feature. You can customize additional service codes in pro...

  • Page 140

    Issue 1.0 univerge sv8100 2 - 106 program 11 : system numbering conditions none feature cross reference r hotel/motel 09 transfer to incoming ring group no setting 10 --- not used --- 11 ethernet port reset 12 extension data swap mlt 92-04 13 remote access from disa no setting 22-02 14 modem access ...

  • Page 141

    Univerge sv8100 issue 1.0 programming manual 2 - 107 description use program 11-16 : single digit service code setup to customize the one-digit service codes used when a busy or ring back signal is heard. You can customize additional service codes in programs 11-10 ~ 11-15. The following chart shows...

  • Page 142

    Issue 1.0 univerge sv8100 2 - 108 program 11 : system numbering conditions none feature cross reference r refer to the input data chart on previous pages. Digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 143

    Univerge sv8100 issue 1.0 programming manual 2 - 109 description use program 11-17 : acd group pilot number to assign the acd master number for each acd group. This is the number users dial to transfer calls to the acd group. Normally, you should use unassigned extension numbers (e.G., 500) for the ...

  • Page 144

    Issue 1.0 univerge sv8100 2 - 110 program 11 : system numbering description use program 11-20 : dial extension analyze table to define the dial type based on three or more digits. This program is only relevant if digits in 11-01-01 are set to 9 (dial extension analyze). Default p dial extension anal...

  • Page 145

    Programming manual 2 - 111 program 12 description use program 12-01 : night mode function setup to set up the night mode options. Refer to the following chart for a description of each option, its range and default setting. Conditions none feature cross reference r night service program 12 : night m...

  • Page 146

    Issue 1.0 univerge sv8100 2 - 112 program 12 : night mode setup description use program 12-02 : automatic night service patterns to define the daily pattern of the automatic mode switching. Each mode group has 10 patterns. These patterns are used in programs 12-03 and 12-04. The daily pattern consis...

  • Page 147

    Univerge sv8100 issue 1.0 programming manual 2 - 113 time pattern 2 default all groups, all patterns : 00:00 to 00:00 = mode 1 time pattern 1 time pattern 2 time pattern 3~10 conditions none feature cross reference r night service 0:00 0:00 mode 2 (night) time setting 01: 00:00 to 00:00 mode 2 (nigh...

  • Page 148

    Issue 1.0 univerge sv8100 2 - 114 program 12 : night mode setup description use program 12-03 : weekly night service switching to define a weekly schedule of night-switch settings. Default program 12 : night mode setup 12-03 : weekly night service switching level: sa input data night mode service gr...

  • Page 149

    Univerge sv8100 issue 1.0 programming manual 2 - 115 conditions none feature cross reference r night service digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 150

    Issue 1.0 univerge sv8100 2 - 116 program 12 : night mode setup description use program 12-04 : holiday night service switching to define a yearly schedule of holiday night-switch settings. This schedule is used for the setting of special days when the company is expected to be closed, such as a nat...

  • Page 151

    Univerge sv8100 issue 1.0 programming manual 2 - 117 description use program 12-05 : night mode group assignment for extensions to a assign day/night mode group for each extension. Conditions none feature cross reference r night service program 12 : night mode setup 12-05 : night mode group assignme...

  • Page 152

    Issue 1.0 univerge sv8100 2 - 118 program 12 : night mode setup description use program 12-06 : night mode group assignment for trunks to assign a day/ night mode group for each trunk port. Conditions none feature cross reference r night service program 12 : night mode setup 12-06 : night mode group...

  • Page 153

    Univerge sv8100 issue 1.0 programming manual 2 - 119 description use program 12-07 : text data for night mode to make an original text message which is displayed on an lcd of multiline telephone in each mode. Default p mode 1 = no setting p mode 2 = p mode 3 = p mode 4 = p mode 5 = p mode 6 = p mode...

  • Page 154

    Issue 1.0 univerge sv8100 2 - 120 program 12 : night mode setup description use program 12-08 : night mode service range to define the changing range of toggle key for each day/night mode. Example: when program 12-08 is set to 3 and the mode key is pressed (sc 751, 09 +0), the following modes are sw...

  • Page 155

    Programming manual 2 - 121 program 13 description use program 13-01 : speed dialing function setup to define the speed dialing functions. Conditions none feature cross reference r speed dial – system/group/station program 13 : abbreviated dialing 13-01 : speed dialing option setup level: sa input da...

  • Page 156

    Issue 1.0 univerge sv8100 2 - 122 program 13 : abbreviated dialing description use program 13-02 : group speed dialing bins to define the range of bin numbers to be used by each speed dialing group. (refer to 13-03 : speed dialing group assignment for extensions ). Default p no setting conditions no...

  • Page 157

    Univerge sv8100 issue 1.0 programming manual 2 - 123 description use program 13-03 : speed dialing group assignment for extensions to assign speed dialing group for each extension. There are 64 available speed dialing groups. Conditions none feature cross reference r speed dial - system/group/statio...

  • Page 158

    Issue 1.0 univerge sv8100 2 - 124 program 13 : abbreviated dialing description use program 13-04 : speed dialing number and name to store speed dialing data in the speed dialing areas. This program is also used to define the names assigned to the speed dialing numbers. Program 13 : abbreviated diali...

  • Page 159

    Univerge sv8100 issue 1.0 programming manual 2 - 125 conditions none feature cross reference r speed dial – system/group/station 05 incoming ring pattern incoming ring pattern 0 = normal pattern 1 ~ 4 = tone pattern (1~4) 5 ~ 9 = scale pattern (1~5) 0 13-04-03 item no. Item input data default relate...

  • Page 160

    Issue 1.0 univerge sv8100 2 - 126 program 13 : abbreviated dialing description use program 13-05 : speed dialing trunk group to define the trunk group to be seized for each speed dialing number. If this program has an entry of ‘0’ (no setting), then seizing a line follows the trunk access group rout...

  • Page 161

    Univerge sv8100 issue 1.0 programming manual 2 - 127 description use program 13-07 : telephone book dial number and name to set up the dial number and name of each telephone book number. Conditions none feature cross reference none program 13 : abbreviated dialing 13-07 : telephone book dial number ...

  • Page 162

    Issue 1.0 univerge sv8100 2 - 128 program 13 : abbreviated dialing description use program 13-08 : telephone book system name to set up the name of the telephone book. Conditions none feature cross reference none program 13 : abbreviated dialing 13-08 : telephone book system name level: sb input dat...

  • Page 163

    Univerge sv8100 issue 1.0 programming manual 2 - 129 description use program 13-09 : telephone book group name to set up the group name of the telephone book. Conditions none feature cross reference none program 13 : abbreviated dialing 13-09 : telephone book group name level: sb input data telephon...

  • Page 164

    Issue 1.0 univerge sv8100 2 - 130 program 13 : abbreviated dialing description use program 13-10 : telephone book routing to set up outgoing mode when using the telephone book. Trunk outgoing mode follows program 14-06 setting. Conditions none feature cross reference none program 13 : abbreviated di...

  • Page 165

    Programming manual 2 - 131 program 14 description use program 14-01 : basic trunk data setup to set the basic options for each trunk port. Refer to the chart below for a description of each option, its range and default setting. Program 14 : trunk, basic setup 14-01 : basic trunk data setup level: i...

  • Page 166

    Issue 1.0 univerge sv8100 2 - 132 program 14 : trunk, basic setup 04 transmit gain level for conference and transfer calls use this option to select the codec gain type used by the trunk when it is part of an unsupervised conference. 1~63 (-15.5db ~ +15.5db in 0.5db intervals) 32 (0db) 05 receive ga...

  • Page 167

    Univerge sv8100 issue 1.0 programming manual 2 - 133 09 private line 0 = disable private line (normal) 1 = enable private line (private line) 0 10 dtmf tones for outgoing calls use this option to enable (1) or disable (0) dtmf tones for outgoing trunk calls. 0 = disable (no) 1 = enable (yes) 0 11 ac...

  • Page 168

    Issue 1.0 univerge sv8100 2 - 134 program 14 : trunk, basic setup 16 forced release of held call use this option to enable/disable forced release for calls on hold. If enabled, the system disconnects a call if it is on hold longer than a programmed interval (program 24-01-05). If disabled, forced di...

  • Page 169

    Univerge sv8100 issue 1.0 programming manual 2 - 135 20 block outgoing caller id allow (1) or prevent (0) the system from automatically blocking outgoing caller id information when a user places a call. If allowed (i.E. Block, enabled), the system automatically inserts the caller id block code (defi...

  • Page 170

    Issue 1.0 univerge sv8100 2 - 136 program 14 : trunk, basic setup default 25 continued/ discontinued trunk-to-trunk conversation enable (1) or disable (0) the ability to dial a service code code to continue or disconnect the trunk- to-trunk conversation after the alert tone is heard. 0 = disable (no...

  • Page 171

    Univerge sv8100 issue 1.0 programming manual 2 - 137 conditions none feature cross reference r refer to features in the input data table. Digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 172

    Issue 1.0 univerge sv8100 2 - 138 program 14 : trunk, basic setup description use program 14-02 : analog trunk data setup to set the basic options for each analog trunk port. Refer to the table below for a description of each option, its range and default setting. Program 14 : trunk, basic setup 14-...

  • Page 173

    Univerge sv8100 issue 1.0 programming manual 2 - 139 06 pause at 1st digit after line seize in manual dial mode 0 = no pause (no) 1 = pause (yes) 1 21-01-06 07 dp to dtmf conversion options determine how a user can convert a dial pulse (dp) call to a dtmf call. For each trunk, set the type of dp to ...

  • Page 174

    Issue 1.0 univerge sv8100 2 - 140 program 14 : trunk, basic setup conditions none feature cross reference none 13 trunk-to-trunk limitation 0 = disable (no) 1 = enable (yes) 0 14 loop start/ground start 0 = loop start (loop) 1 = ground start (ground) 0 16 --- not used --- 17 sync. Ringing use this t...

  • Page 175: 14-04 : Behind Pbx Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 141 description use program 14-04 : behind pbx setup to indicate if the trunk is installed behind a pbx. There is one item for each mode. Conditions none feature cross reference r central office calls, placing program 14 : trunk, basic setup 14-04 : b...

  • Page 176: 14-05 : Trunk Group

    Issue 1.0 univerge sv8100 2 - 142 program 14 : trunk, basic setup description use program 14-05 : trunk group to assign trunks to trunk groups. You can also assign the outbound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in...

  • Page 177

    Univerge sv8100 issue 1.0 programming manual 2 - 143 description use program 14-06 : trunk group routing to set up an outbound routing table for the trunk groups you assigned in program 14-05. When users dial 9, the system routes their calls in the order (priority) specified. For example, if a user ...

  • Page 178

    Issue 1.0 univerge sv8100 2 - 144 program 14 : trunk, basic setup default p route 1, order number 1 = 1 (trunk group 1). P order numbers 2, 3, 4 = 0 (not specified). P all other routes (2~100) and order numbers (1~4) = 0 (not specified). Conditions none feature cross reference none input data route ...

  • Page 179

    Univerge sv8100 issue 1.0 programming manual 2 - 145 description use program 14-07 : trunk access map setup to set up the trunk access maps. This sets an extension access options for trunks. For example, an extension can only place outgoing calls on trunks to which it has outgoing access. There are ...

  • Page 180

    Issue 1.0 univerge sv8100 2 - 146 program 14 : trunk, basic setup conditions none feature cross reference r central office calls, answering r central office calls, placing digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 181

    Univerge sv8100 issue 1.0 programming manual 2 - 147 description use program 14-08 : music on hold source for trunks to define a music on hold source for a trunk as either the aci or coi port. If aci is selected as the source in item 1, the port number for the source must be selected in item 2. Cond...

  • Page 182

    Issue 1.0 univerge sv8100 2 - 148 program 14 : trunk, basic setup description use program 14-09 : conversation recording destination for trunks to set the aci conversation recording destination for each trunk. If both programs 14-09 and 15-12 define a destination, the destination in program 15-12 is...

  • Page 183

    Univerge sv8100 issue 1.0 programming manual 2 - 149 description use program 14-11 : id setup for ip trunk to set the id of each ip trunk. This program refers to incoming and outgoing ip trunk calls. The id is sent on an outgoing ip trunk call. This program is used only for h.323. Conditions p this ...

  • Page 184

    Issue 1.0 univerge sv8100 2 - 150 program 14 : trunk, basic setup description use program 14-12 : sip register id setup for ip trunk to define the sip register id for ip trunks. Conditions none feature cross reference r none program 14 : trunk, basic setup 14-12 : sip register id setup for ip trunk ...

  • Page 185

    Univerge sv8100 issue 1.0 programming manual 2 - 151 description use program 14-13 : ccis system route id to define the ccis route id to the trunk group used for k-ccis. Conditions p not used for ip-ccis feature cross reference r key-common channel interoffice signaling (k-ccis) program 14 : trunk, ...

  • Page 186

    Issue 1.0 univerge sv8100 2 - 152 program 14 : trunk, basic setup description use program 14-14 : ccis trunk cic assignment to define the cic (circuit identifier code) to each voice channel (trunk port) used for k-ccis. Conditions p cic numbers must be assigned consecutively for k-ccis to operate co...

  • Page 187

    Programming manual 2 - 153 program 15 description use program 15-01 : basic extension data setup to define the basic settings for each extension. Program 15 : extension, basic setup 15-01 : basic extension data setup level: sa input data extension number maximum eight digits item no. Item input data...

  • Page 188

    Issue 1.0 univerge sv8100 2 - 154 program 15 : extension, basic setup conditions none feature cross reference none 04 isdn caller id if both program 15-01-04 and 10-03-05 are enabled, the system includes caller id in the setup message as presentation allowed. If these options are disabled, it is pre...

  • Page 189

    Univerge sv8100 issue 1.0 programming manual 2 - 155 description use program 15-02 : multiline telephone basic data setup to set up various multiline telephone options. Program 15 : extension, basic setup 15-02 : multiline telephone basic data setup level: in input data extension number maximum eigh...

  • Page 190

    Issue 1.0 univerge sv8100 2 - 156 program 15 : extension, basic setup 03 extension ring tone use this option to set the tone (pitch) of the incoming extension call ring for the extension port you are programming. Also refer to program 15-08. Dtu/dtp style telephones only follow high, medium and low ...

  • Page 191

    Univerge sv8100 issue 1.0 programming manual 2 - 157 11 callback automatic answer use this option to enable or disable automatic answer of calls recalling to a station. For example, if a transfer recall or hold recall is ringing back to a station, the following happens: if prg 15-02-11 is enabled, t...

  • Page 192

    Issue 1.0 univerge sv8100 2 - 158 program 15 : extension, basic setup 20 baud rate for cta port select the baud rate to be used by the cta adapter. 0 = 4800 1 = 9600 2 = 19200 2 15-02-19 21 virtual extension access mode (when idle virtual extension key pressed) determine whether a virtual extension/...

  • Page 193

    Univerge sv8100 issue 1.0 programming manual 2 - 159 24 conference key mode this option allows an extension conf key to be programmed for conference or for transfer. When set for transfer (1), the user places a call on hold, dials the extension to which it should be transferred, then presses the con...

  • Page 194

    Issue 1.0 univerge sv8100 2 - 160 program 15 : extension, basic setup 34 call register mode the caller id scroll stores trunk calls only (0), or both internal and trunk calls (1). 0 = trunk mode 1 = extension/trunk mode 0 35 message waiting lamp cycle for calling extension select the cycle method th...

  • Page 195

    Univerge sv8100 issue 1.0 programming manual 2 - 161 43 headset ring duration 0 = no switch to speaker ring 1 = 10 seconds 2 = 20 seconds 3 = 30 seconds 4 = 40 seconds 5 = 50 seconds 6 = 1 minute 0 44 reversing display indication the display on the dt300/dt700 style telephones can be set to normal (...

  • Page 196

    Issue 1.0 univerge sv8100 2 - 162 program 15 : extension, basic setup conditions none feature cross reference r refer to the input data chart. Table 2-4 lamp cycle on/off timing pattern programs 15-02-35, 36, and 38 input cycle 1 cycle 1 500ms – on / 500ms – off 2 cycle 2 250ms – on / 250ms – off 3 ...

  • Page 197

    Univerge sv8100 issue 1.0 programming manual 2 - 163 description use program 15-03 : single line telephone basic data setup to set up various single line telephone options. Program 15 : extension, basic setup 15-03 : single line telephone basic data setup level: in input data extension number maximu...

  • Page 198

    Issue 1.0 univerge sv8100 2 - 164 program 15 : extension, basic setup 06 extension polarity reverse not used in u.S. -- do not change default entry as dtmf issues may arise with voice mail. 0 = disable (off) 1 = enable (on) 0 07 enabled on-hook when holding (slt) 0 = no 1 = yes 1 11-12-45 08 answer ...

  • Page 199

    Univerge sv8100 issue 1.0 programming manual 2 - 165 conditions none feature cross reference r single line telephones, analog 500/2500 sets 17 dial tone select when the function of mw has been set from another extension or vm, the dial tone upon off hook is selected. 0 = normal 1 = new dt 0 item no ...

  • Page 200

    Issue 1.0 univerge sv8100 2 - 166 program 15 : extension, basic setup description use program 15-05 : ip telephone terminal basic data setup to set up the basic settings for an ip telephone. Program 15 : extension, basic setup 15-05 : ip telephone terminal basic data setup level: in input data exten...

  • Page 201

    Univerge sv8100 issue 1.0 programming manual 2 - 167 16 authentication password up to 24 characters none assign the authentication password for sip single line telephones. 15-05-01 17 calling party display info 0 = nickname 1 = display name 2 = user part 3 = extension 0 the part of the invite messag...

  • Page 202

    Issue 1.0 univerge sv8100 2 - 168 program 15 : extension, basic setup 22 side option additional data 0 = no setting 1~32 = dss console number 0 this is a read only program that shows the dss console number when one is installed on a ith-style telephone. 30-01 30-02 30-03 30-04 30-05 30-06 23 handset...

  • Page 203

    Univerge sv8100 issue 1.0 programming manual 2 - 169 conditions p 15-05-04 – nickname must be unique in the system. Feature cross reference none 30 dtmf play during conversation at receive extension 0 = do not play 1 = play 0 31 alarm tone during conversation (rtp packet loss alarm) 0 = off 1 = on 1...

  • Page 204

    Issue 1.0 univerge sv8100 2 - 170 program 15 : extension, basic setup description use program 15-06 : trunk access map for extensions to define the trunk access map for each extension. An extension can only place outgoing calls on trunks to which it has outgoing access. Use program 14-07 to define t...

  • Page 205

    Univerge sv8100 issue 1.0 programming manual 2 - 171 description use program 15-07 : programmable function keys to assign functions to a multiline terminal line keys. For certain functions, you can append data to the key basic function. For example, the function 26 appended by data 1 makes a group c...

  • Page 206

    Issue 1.0 univerge sv8100 2 - 172 program 15 : extension, basic setup default programmable keys 1~8 are trunk line keys (key 1 = trunk line 1, key 2 = trunk line 2, etc.). All other programmable keys are undefined. Function number list [1] normal function code (00 ~ 99) (service code 751) item no. L...

  • Page 207

    Univerge sv8100 issue 1.0 programming manual 2 - 173 11 call forward – busy slow blink (red): forwarded 12 call forward – no answer slow blink (red): forwarded 13 call forward – busy/no answer slow blink (red): forwarded 14 call forward – both ring slow blink (red): forwarded 15 follow me rapid blin...

  • Page 208

    Issue 1.0 univerge sv8100 2 - 174 program 15 : extension, basic setup 36 step call none 37 dnd/fwd override call none 38 message waiting none 39 room monitoring rapid blink (red): while being monitored slow blink (red): while monitoring 40 handset transmission cutoff red on: transmission cut-off 41 ...

  • Page 209

    Univerge sv8100 issue 1.0 programming manual 2 - 175 56 general purpose led operation blink (red): active 57 general purpose led indication blink (red): active 58 automatic transfer at department group call extension group number ( 01~64) blink (red): active 59 delayed transfer at department group c...

  • Page 210

    Issue 1.0 univerge sv8100 2 - 176 program 15 : extension, basic setup 79 automated attendant (in-skin) extension number or pilot number red on: set up for all calls fast blink (red): set up for no answer calls stutter blink (red): set up for busy calls slow blink (red): set up for busy/no answer cal...

  • Page 211

    Univerge sv8100 issue 1.0 programming manual 2 - 177 97 door box access key door box number (1~8) on: door box busy off: door box idle fast flash: door box incoming 98~99 --- not used --- function number list (continued) [1] normal function code (00 ~ 99) (service code 751) function number function ...

  • Page 212

    Issue 1.0 univerge sv8100 2 - 178 program 15 : extension, basic setup 4 13 acd off duty mode red on: under off duty slow blink (red): under reservation 4 14 acd start/end red on: acd operation end 4 15 acd terminal speech monitor red on: under monitor 4 16 acd waiting red on: standby 4 17 acd work w...

  • Page 213

    Univerge sv8100 issue 1.0 programming manual 2 - 179 led indication reference: on = led pattern 7 (on). Off = led pattern 0 (off). Rapid blink = led pattern 3 (rw). Slow blink (general function level) = led pattern 5 (il). Slow blink (appearance function level) = led pattern 1 (fl). Fast blink = led...

  • Page 214

    Issue 1.0 univerge sv8100 2 - 180 program 15 : extension, basic setup conditions p when a key is programmed using service code 752, that key cannot be programmed with a function using the 751 code until the key is undefined (000). For example with a park key programmed by dialing 752 + 4 04 must be ...

  • Page 215

    Univerge sv8100 issue 1.0 programming manual 2 - 181 description use program 15-08 : incoming virtual extension ring tone setup to assign a ring tone range (0~4) to incoming virtual extensions assigned to a virtual extension key (program 15-07). If you enable ringing for the key in program 15-09, th...

  • Page 216

    Issue 1.0 univerge sv8100 2 - 182 program 15 : extension, basic setup conditions none feature cross reference none table 2-6 program 15-08 – incoming signal frequency patterns incoming signal frequency pattern type frequency 1 frequency 2 modulation pattern 1 high middle low 1100 660 520 1400 760 66...

  • Page 217

    Univerge sv8100 issue 1.0 programming manual 2 - 183 description use program 15-09 : virtual extension ring assignment to assign the ringing options for an extension virtual extension key or virtual extension group answer key which is defined in program 15-07. You make an assignment for each night s...

  • Page 218

    Issue 1.0 univerge sv8100 2 - 184 program 15 : extension, basic setup description use program 15-10 : incoming virtual extension ring tone order setup to set the priority (1~4) for the virtual extension ring tones set in program 15-08. When virtual extension calls ring an extension simultaneously, t...

  • Page 219

    Univerge sv8100 issue 1.0 programming manual 2 - 185 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 220

    Issue 1.0 univerge sv8100 2 - 186 program 15 : extension, basic setup description use program 15-11 : virtual extension delayed ring assignment to assign the delayed ringing options for an extension virtual extension or virtual extension group answer keys (defined in program 15-09). You make an assi...

  • Page 221

    Univerge sv8100 issue 1.0 programming manual 2 - 187 description use program 15-12 : conversation recording destination for extensions to set the aci conversation recording destination for each extension. If both programs 14-09 and 15-12 define a destination, the destination in program 15-12 is foll...

  • Page 222

    Issue 1.0 univerge sv8100 2 - 188 program 15 : extension, basic setup description use program 15-14 : programmable one-touch keys to define the one-touch key data for each multiline terminal. For each univerge sv8100 wireless telephone to use the transfer when out of range feature, enter the destina...

  • Page 223

    Univerge sv8100 issue 1.0 programming manual 2 - 189 description use program 15-16 : sip register setup for extensionto define the sip register id for extensions. Conditions none feature cross reference none program 15 : extension, basic setup 15-16 : sip register id setup for extension level: in in...

  • Page 224

    Issue 1.0 univerge sv8100 2 - 190 program 15 : extension, basic setup description use program 15-17 : co message waiting indication to set the message waiting led flash assignment on each co line. Conditions none feature cross reference none program 15 : extension, basic setup 15-17 : co message wai...

  • Page 225

    Univerge sv8100 issue 1.0 programming manual 2 - 191 description use program 15-18 : virtual extension key enhanced options to define the operation when a virtual extension key is pressed. Default settings p if a dil rings a virtual extension, the virtual extension key operation mode must be set to ...

  • Page 226

    Issue 1.0 univerge sv8100 2 - 192 program 15 : extension, basic setup description use program 15-19 : system telephone book setup for extension to set the operations of the telephone book for each extension. Conditions none feature cross reference none program 15 : extension, basic setup 15-19 : sys...

  • Page 227

    Univerge sv8100 issue 1.0 programming manual 2 - 193 description use program 15-20 : lcd line key name assignmentto assigns a name to each lcd line key of the sv8100 telephones and adm option. Up to 13 characters can be assigned. Default settings conditions none feature cross reference none program ...

  • Page 228

    Issue 1.0 univerge sv8100 2 - 194 program 15 : extension, basic setup description use program 15-22 : mobile extension setup to set the system information for the mobile extension feature. Conditions none feature cross reference none program 15 : extension, basic setup 15-22 : mobile extension setup...

  • Page 229

    Programming manual 2 - 195 program 16 description use program 16-01 : department group basic data setup to set the function mode for each department group. There are 64 available department groups. Program 16 : department group setup 16-01 : department group basic data setup level: in input data dep...

  • Page 230

    Issue 1.0 univerge sv8100 2 - 196 program 16 : department group setup 04 hunting mode use this option to set the action taken when a call reaches the last extension in the department group (0=hunting stopped, 1 =hunting repeats with circular routing through the department group). 0 = last extension ...

  • Page 231

    Univerge sv8100 issue 1.0 programming manual 2 - 197 conditions none feature cross reference r department calling digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 232

    Issue 1.0 univerge sv8100 2 - 198 program 16 : department group setup description use program 16-02 : department group assignment for extensions to set the department groups. The system uses these groups (64 department groups) for department calling. Assign pilot numbers to department groups you set...

  • Page 233

    Univerge sv8100 issue 1.0 programming manual 2 - 199 description use program 16-03 : secondary department group to set a second department group for extensions. Up to 16 extensions can be assigned per a department group. There are 64 available department groups. Default p all extension groups : no s...

  • Page 234

    Issue 1.0 univerge sv8100 2 - 200 program 16 : department group setup description use program 16-04 : call restriction between department groups to set internal calls between members of different department (station) groups that can be restricted on a per group basis. Each department group can restr...

  • Page 235: 20-01 : System Options

    Programming manual 2 - 201 program 20 description use program 20-01 : system options to set various system options. Program 20 : system option setup 20-01 : system options level: in input data item no. Item input data default description related program 01 operator access mode 0 = step call 1 = circ...

  • Page 236

    Issue 1.0 univerge sv8100 2 - 202 program 20 : system option setup conditions none feature cross reference r refer to the input data table at the beginning of this section. Digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 237

    Univerge sv8100 issue 1.0 programming manual 2 - 203 description use program 20-02 : system options for multiline telephones to set various system options for multiline telephones. Program 20 : system option setup 20-02 : system options for multiline telephones level: in input data item no. Item inp...

  • Page 238

    Issue 1.0 univerge sv8100 2 - 204 program 20 : system option setup 09 disconnect supervision use this option to enable or disable disconnect supervision for the system trunks. 0 = disable (off) 1 = enable (on) 1 10 time before shifting to power-saving mode 0 = no shift 1 = 1 minute 2 = 2 minutes 3 =...

  • Page 239

    Univerge sv8100 issue 1.0 programming manual 2 - 205 conditions none feature cross reference r none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 240

    Issue 1.0 univerge sv8100 2 - 206 program 20 : system option setup description use program 20-03 : system options for single line telephones to set up various options for single line telephones. Program 20 : system option setup 20-03 : system options for single line telephones level: in input data i...

  • Page 241

    Univerge sv8100 issue 1.0 programming manual 2 - 207 conditions none feature cross reference r single line telephones, analog 500/2500 sets 04 dial sending start time for slt or ars when ars or an analog extension user accesses a trunk and dials an outside call, the system waits this interval before...

  • Page 242

    Issue 1.0 univerge sv8100 2 - 208 program 20 : system option setup description use program 20-04 : system options for virtual extensions to set up various system options for virtual extensions. There are 256 available virtual extension ports. Input data conditions none feature cross reference r call...

  • Page 243

    Univerge sv8100 issue 1.0 programming manual 2 - 209 description use program 20-06 : class of service for extensions to assign a class of service (cos) to an extension. There are 15 classes of service that can be assigned. To specify the options in each class of service, refer to programs 20-07 thro...

  • Page 244

    Issue 1.0 univerge sv8100 2 - 210 program 20 : system option setup description use program 20-07 : class of service options (administrator level) to define the administrator service availability for each extension class of service (cos). Program 20 : system option setup 20-07 : class of service opti...

  • Page 245

    Univerge sv8100 issue 1.0 programming manual 2 - 211 10 programmable function key programming (appearance level) turns off or on the ability for an extension to program the appearance function keys using service code 752. 0 = off 1 = on 1 1 11-11-38 20-13-18 11 forced trunk disconnect (analog trunk ...

  • Page 246

    Issue 1.0 univerge sv8100 2 - 212 program 20 : system option setup conditions none feature cross reference r class of service 26 dial-in mode switch 0 = off 1 = on 0 0 11-10-35 27 do-not-call administrator 0 = off 1 = on 0 0 25-01-07 15-07-89 20-01-19 28 --- not used --- 30 date setting 0 = off 1 = ...

  • Page 247

    Univerge sv8100 issue 1.0 programming manual 2 - 213 description use program 20-08 : class of service options (outgoing call service) to define the outgoing call feature availability for each extension class of service (cos). Program 20 : system option setup 20-08 : class of service options (outgoin...

  • Page 248

    Issue 1.0 univerge sv8100 2 - 214 program 20 : system option setup 09 hotline/extension ringdown turns off or on ringdown extension for extensions with this cos. 0 = off 1 = on 0 0 10 signal/voice call turns off or on an extension allowing it to force handsfree answerback or forced intercom ringing ...

  • Page 249

    Univerge sv8100 issue 1.0 programming manual 2 - 215 conditions none feature cross reference r class of service 21 automatic trunk seizing by pressing spk key the ability of an extension to automatically access trunk route when going off hook via the speaker key. 0 = off 1 = on 0 0 22 voice over to ...

  • Page 250

    Issue 1.0 univerge sv8100 2 - 216 program 20 : system option setup description use program 20-09 : class of service options (incoming call service) to define the incoming call feature availability for each extension class of service (cos). Program 20 : system option setup 20-09 : class of service op...

  • Page 251

    Univerge sv8100 issue 1.0 programming manual 2 - 217 conditions none feature cross reference r class of service 05 signal/voice call turn off or on an extension ability to enable handsfree answerback or forced intercom ringing for their incoming intercom calls. 0 = off 1 = on 1 1 11-11-15, 11-11-16 ...

  • Page 252

    Issue 1.0 univerge sv8100 2 - 218 program 20 : system option setup description use program 20-10 : class of service options (answer service) to define the answer feature availability for each extension class of service (cos). Program 20 : system option setup 20-10 : class of service options (answer ...

  • Page 253

    Univerge sv8100 issue 1.0 programming manual 2 - 219 conditions none feature cross reference none 08 virtual extension off-hook answer turns off or on an extension to answer an incoming call on a call arrival (car)/secondary incoming extension (sie)/ virtual extension simply by lifting the handset. ...

  • Page 254

    Issue 1.0 univerge sv8100 2 - 220 program 20 : system option setup description use program 20-11 : class of service options (hold/transfer service) to define the hold and transfer feature availability for each extension class of service (cos). Program 20 : system option setup 20-11 : class of servic...

  • Page 255

    Univerge sv8100 issue 1.0 programming manual 2 - 221 08 transfer information display turns off or on an extension ability for incoming transfer preanswer display. 0 = off 1 = on 1 1 09 group hold initiate turns off or on an extension ability to initiate a group hold. 0 = off 1 = on 1 1 10 group hold...

  • Page 256

    Issue 1.0 univerge sv8100 2 - 222 program 20 : system option setup conditions none feature cross reference r class of service 20 no callback turns off or on an extension to receive callbacks. 0 = off 1 = on 0 0 21 restriction for tandem trunking on hang up allow (0) or deny (1) an extension user abi...

  • Page 257

    Univerge sv8100 issue 1.0 programming manual 2 - 223 description use program 20-12 : class of service options (charging cost service) to define the charging cost service availability for each extension service class. Conditions none feature cross reference r class of service program 20 : system opti...

  • Page 258

    Issue 1.0 univerge sv8100 2 - 224 program 20 : system option setup description use program 20-13 : class of service options (supplementary service) to define the supplementary feature availability for each extension class of service (cos). Program 20 : system option setup 20-13 : class of service op...

  • Page 259

    Univerge sv8100 issue 1.0 programming manual 2 - 225 08 conference turns off or on an extension user ability to initiate a conference or meet-me conference. 0 = off 1 = on 1 1 09 privacy release turns off or on an extension user ability to initiate a voice call conference. 0 = off 1 = on 1 1 10 barg...

  • Page 260

    Issue 1.0 univerge sv8100 2 - 226 program 20 : system option setup 19 selectable display messaging (text messaging) turns off or on an extension user ability to use selectable display messaging. 0 = off 1 = on 1 1 20 account code/toll restriction operator alert (restricted operation transfer) turns ...

  • Page 261

    Univerge sv8100 issue 1.0 programming manual 2 - 227 31 connected line identification (colp) 0 = off 1 = on 0 0 32 deny multiple barge-ins allows or denies an extension from having multiple users barge into their conversation. 0 = off 1 = on 0 0 33 acd supervisor’s position enhancement this option m...

  • Page 262

    Issue 1.0 univerge sv8100 2 - 228 program 20 : system option setup conditions none feature cross reference r class of service 44 live monitor enabling turn off or on an extension user ability to use live monitor. 0 = off 1 = on 1 1 45 mic key mode while call monitoring set per class of service, when...

  • Page 263

    Univerge sv8100 issue 1.0 programming manual 2 - 229 description use program 20-14 : class of service options for disa/e&m to enable/disable disa and tie line class of service options. You assign a disa class of service to disa users in program 25-09. Assign tie line classes of service in 34-02. Up ...

  • Page 264

    Issue 1.0 univerge sv8100 2 - 230 program 20 : system option setup conditions none feature cross reference r class of service r direct inward system access (disa) r tie lines 07 external paging this option enables or disables a disa or tie trunk caller ability to use the telephone system external pa...

  • Page 265: 20-15 : Ring Cycle Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 231 description use program 20-15 : ring cycle setup to define the ringing cycles for each ring type. Program 20 : system option setup 20-15 : ring cycle setup level: in input data item no. Incoming signal type ringing cycle default 01 normal incoming...

  • Page 266

    Issue 1.0 univerge sv8100 2 - 232 program 20 : system option setup conditions none feature cross reference none table 2-7 ringing cycles number ringing cycle 1 on 2 on:2.0 / off:4.0 3 on:1.0 / off:2.0 4 on:0.5 / off:0.5 5 on:0.25 / off:0.25 6 on:0.5 / off:0.5 / on:0.5 / off:1.5 7 on:0.25 / off:0.25 ...

  • Page 267

    Univerge sv8100 issue 1.0 programming manual 2 - 233 description use program 20-16 : selectable display messages to enter the selectable display messages. There are 20 alphanumeric messages, with up to 24 characters. Use the following chart when programming messages. Program 20 : system option setup...

  • Page 268

    Issue 1.0 univerge sv8100 2 - 234 program 20 : system option setup when using dtp or dtu style telephones on the univerge sv8100 system, not all the same characters are available. Input data selectable display message number 01~20 item no. Input data 01 24 characters default number message 1 in meet...

  • Page 269

    Univerge sv8100 issue 1.0 programming manual 2 - 235 conditions p time value ## : ## must be followed by two spaces. Feature cross reference r selectable display messages digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 270

    Issue 1.0 univerge sv8100 2 - 236 program 20 : system option setup description use program 20-17 : operator extension to designate an operator. When an extension user dials 0 or 9 (defined by program 11-01 type 5), calls go to the operator selected in this program. If you do not assign an extension ...

  • Page 271

    Univerge sv8100 issue 1.0 programming manual 2 - 237 description use program 20-18 : service tone timers to set the values for the system service tone timers. Refer to the following chart for a description of each option, its range and default setting. Program 20 : system option setup 20-18 : servic...

  • Page 272

    Issue 1.0 univerge sv8100 2 - 238 program 20 : system option setup conditions none feature cross reference r distinctive ringing, tones, and flash patterns digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 273

    Univerge sv8100 issue 1.0 programming manual 2 - 239 description use program 20-19 : system options for caller id to define the system options for the caller id feature. Conditions none feature cross reference r caller id program 20 : system option setup 20-19 : system options for caller id level: i...

  • Page 274

    Issue 1.0 univerge sv8100 2 - 240 program 20 : system option setup description use program 20-20 : message setup for non-caller id data to define the messages which are displayed when no caller id information is received. Conditions none feature cross reference r caller id program 20 : system option...

  • Page 275

    Univerge sv8100 issue 1.0 programming manual 2 - 241 description use program 20-21 : system options for long conversation to define the system options for the long conversation feature. Conditions none feature cross reference r long conversation cutoff program 20 : system option setup 20-21 : system...

  • Page 276

    Issue 1.0 univerge sv8100 2 - 242 program 20 : system option setup description use program 20-22 : system options for wireless – dect service to define the time the system waits before determining the wireless – dect phone is out of range. For incoming calls, the timer begins when the call is receiv...

  • Page 277

    Univerge sv8100 issue 1.0 programming manual 2 - 243 description use program 20-23 : system options for cti to define the system options for the cti feature. Conditions none feature cross reference r computer telephony integration (cti) applications program 20 : system option setup 20-23 : system op...

  • Page 278: 20-25 : Isdn Options

    Issue 1.0 univerge sv8100 2 - 244 program 20 : system option setup description use program 20-25 : isdn options to define the isdn system options. Program 20 : system option setup 20-25 : isdn options level: in input data item no. Item input data default 01 send the release message after subscriber ...

  • Page 279

    Univerge sv8100 issue 1.0 programming manual 2 - 245 conditions none feature cross reference r isdn compatibility 11 automatic changing system clock when date/ time information element received 0 = disable (off) 1 = enable (on) 0 12 call forward options (auto connect send) incoming calls forwarded o...

  • Page 280

    Issue 1.0 univerge sv8100 2 - 246 program 20 : system option setup description use program 20-26 : multiplier changing co to define the multiplier for charging cost to each extension service class. Conditions none feature cross reference none program 20 : system option setup 20-26 : multiplier chang...

  • Page 281

    Univerge sv8100 issue 1.0 programming manual 2 - 247 description use program 20-28 : trunk to trunk conversation to define system options for trunk to trunk conversation. Conditions none feature cross reference none program 20 : system option setup 20-28 : trunk to trunk conversation level: in input...

  • Page 282

    Issue 1.0 univerge sv8100 2 - 248 program 20 : system option setup description use program 20-29 : timer class for extension to assign the timer class to each extension. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. This entry in...

  • Page 283

    Univerge sv8100 issue 1.0 programming manual 2 - 249 description use program 20-30 : timer class for trunks to assign the timer class to each trunk. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. The details of classes are assigne...

  • Page 284

    Issue 1.0 univerge sv8100 2 - 250 program 20 : system option setup description use program 20-31 : timer class timer assignment to assign values to the timers on a class of service basis. Program 20 : system option setup 20-31 : timer class timer assignment level: in input data timer class number 0~...

  • Page 285

    Univerge sv8100 issue 1.0 programming manual 2 - 251 07 ring no answer alarm time if a trunk rings a multiline telephone longer than this interval, the system changes the ring cadence. This indicates to the user that the call has been ringing too long. 0~64800 seconds 60 seconds 22-01-03 08 dil/inco...

  • Page 286

    Issue 1.0 univerge sv8100 2 - 252 program 20 : system option setup 15 delayed call forwarding time (call forward no answer) if activated at an extension, delayed call forwarding occurs after this time. This also sets how long a transferred call waits at an extension forwarded to voice mail before ro...

  • Page 287

    Univerge sv8100 issue 1.0 programming manual 2 - 253 conditions p these timers are used when an extension or trunk is assigned to a class from 1 to 16 in 20-29-01 or 20-30-01. When the timer class is set to 0, the system-wide timer is used. P all defaults are the same as the system-wide timers. Feat...

  • Page 288

    Issue 1.0 univerge sv8100 2 - 254 program 20 : system option setup description use program 20-35 : extension’s operator setting to assign an extension to an operator group. Conditions none feature cross reference none program 20 : system option setup 20-35 : extension’s operator setting level: in in...

  • Page 289

    Univerge sv8100 issue 1.0 programming manual 2 - 255 description use program 20-36 : trunk’s operator setting to assign a trunk to an operator group. Conditions none feature cross reference none program 20 : system option setup 20-36 : trunk’s operator setting level: in input data trunk port number ...

  • Page 290

    Issue 1.0 univerge sv8100 2 - 256 program 20 : system option setup description use program 20-37 : operator extension group setup to define the operator(s) in the operator group. Conditions none feature cross reference none program 20 : system option setup 20-37 : operator extension group setup leve...

  • Page 291

    Univerge sv8100 issue 1.0 programming manual 2 - 257 description use program 20-38 : operator group setting to set up priority of a call when calling an operator telephone. Conditions none feature cross reference none program 20 : system option setup 20-38 : operator group setting level: in input da...

  • Page 292

    Issue 1.0 univerge sv8100 2 - 258 program 20 : system option setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 293

    Programming manual 2 - 259 program 21 description use program 21-01 : system options for outgoing calls to set the system options for outgoing call service. Program 21 : outgoing call setup 21-01 : system options for outgoing calls level: in input data item no. Item input data default related progra...

  • Page 294

    Issue 1.0 univerge sv8100 2 - 260 program 21 : outgoing call setup 05 disconnect time when dial tone not detected if 14-02-11 is enabled, the system skips over a trunk if dial tone is not detected. This option pertains to calls placed using speed dial, ars, last number redial or save number dialed. ...

  • Page 295

    Univerge sv8100 issue 1.0 programming manual 2 - 261 12 dial e911 routing without trunk access if enabled (1), an extension user can dial 911 (usa only) without first dialing a trunk access code or pressing a line key. If disabled (0), an extension user must dial a trunk access code (e.G., 9) or pre...

  • Page 296

    Issue 1.0 univerge sv8100 2 - 262 program 21 : outgoing call setup conditions none feature cross reference r central office calls, placing digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 297

    Univerge sv8100 issue 1.0 programming manual 2 - 263 description use program 21-02 : trunk group routing for extensions to assign program 14-06 routes to extensions. Conditions none feature cross reference none program 21 : outgoing call setup 21-02 : trunk group routing for extensions level: in inp...

  • Page 298

    Issue 1.0 univerge sv8100 2 - 264 program 21 : outgoing call setup description use program 21-03 : trunk group routing for trunks to set the trunk route table for automatic external call forward. The route table is set in program 14-06. Conditions none feature cross reference r trunk group routing p...

  • Page 299

    Univerge sv8100 issue 1.0 programming manual 2 - 265 description use program 21-04 : toll restriction class for extensions to assign a toll restriction class to an extension. The details of toll restriction are defined in program 21-05 and 21-06. A telephone and a trunk will have a restriction class...

  • Page 300

    Issue 1.0 univerge sv8100 2 - 266 program 21 : outgoing call setup description use program 21-05 : toll restriction class to set the system toll restriction classes (1~15). Program 21 : outgoing call setup 21-05 : toll restriction class level: in input data toll restriction class number 1~15 item no...

  • Page 301

    Univerge sv8100 issue 1.0 programming manual 2 - 267 08 restriction table 1~4 = table 0 = disable (none) 1, 2, 6~15 = 0 3 = 1 4 = 2 5 = 3 set the tables 1~4 when referring to the table set up by 21-06-07. 21-06-07 09 restriction for common speed dials 0 = does not restrict 1 = following restriction ...

  • Page 302

    Issue 1.0 univerge sv8100 2 - 268 program 21 : outgoing call setup default conditions none feature cross reference none toll restriction class item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 01: international call restrict table 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 02: international call permit table 0 1 0 0 0 0 ...

  • Page 303

    Univerge sv8100 issue 1.0 programming manual 2 - 269 description use program 21-06 : toll restriction table data setup to set the system toll restriction data. Dial 1-9, 0, 4 , # can be entered in each table. Program 21 : outgoing call setup 21-06 : toll restriction table data setup level: in input ...

  • Page 304

    Issue 1.0 univerge sv8100 2 - 270 program 21 : outgoing call setup 06 permit code table 1 ~ 4 (table) 001 ~ 200 (entry) dial (up to 12 digits) table 1 ~ 4 = no setting this option lets you program the permit code tables. If the system has toll restriction enabled, users can dial numbers only if perm...

  • Page 305

    Univerge sv8100 issue 1.0 programming manual 2 - 271 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 306

    Issue 1.0 univerge sv8100 2 - 272 program 21 : outgoing call setup description use program 21-07 : toll restriction override password setup to assign toll restriction override codes to extension ports. Each code must have four digits, using any combination of 0~9, # and 4 . Each extension can have a...

  • Page 307

    Univerge sv8100 issue 1.0 programming manual 2 - 273 description use program 21-08 : repeat dial setup to define the automatic repeat dial data. Conditions none feature cross reference none program 21 : outgoing call setup 21-08 : repeat dial setup level: in input data item no. Item input data defau...

  • Page 308: 21-09 : Dial Block Setup

    Issue 1.0 univerge sv8100 2 - 274 program 21 : outgoing call setup description use program 21-09 : dial block setup to define the dial blocking toll restriction class and dial block password to be used by the supervisor extension. Conditions p this function works by password and class of service con...

  • Page 309

    Univerge sv8100 issue 1.0 programming manual 2 - 275 description use program 21-10 : dial block restriction class per extension to define the toll restriction class to each extension when the extension is set for dial block restriction. If this data is 0, toll restriction class follows program 21-09...

  • Page 310

    Issue 1.0 univerge sv8100 2 - 276 program 21 : outgoing call setup description use program 21-11 : extension ringdown (hotline) assignment to define the hotline destination number for each extension number. Conditions p the @ code is used to make an outbound call automatically to a disa trunk or to ...

  • Page 311

    Univerge sv8100 issue 1.0 programming manual 2 - 277 description use program 21-12 : isdn calling party number setup for trunks to assign calling party numbers for each trunk (maximum 16 digits per entry). When a call is made by an extension which does not have an extension calling number assigned (...

  • Page 312

    Issue 1.0 univerge sv8100 2 - 278 program 21 : outgoing call setup description use program 21-13 : isdn calling party number setup for extensions to assign each extension a calling party number (maximum 16 digits per entry). The calling number is the subscriber number of the dial-in number. When a c...

  • Page 313

    Univerge sv8100 issue 1.0 programming manual 2 - 279 description use program 21-14 : walking toll restriction password setup to assign the password and toll restriction class for walking toll restriction. Each code is six digits long, using any combination of 0~9, # and 4 . Conditions none feature c...

  • Page 314

    Issue 1.0 univerge sv8100 2 - 280 program 21 : outgoing call setup description use program 21-15 : individual trunk group routing for extensions to designate the alternate trunk access route accessed when a user dials the alternate trunk route access code. Refer to program 11-09 : trunk access code ...

  • Page 315

    Univerge sv8100 issue 1.0 programming manual 2 - 281 description use program 21-17 : ip trunk (sip) calling party number setup for trunk set the sip calling party number for individual trunks. Conditions none feature cross reference none program 21 : outgoing call setup 21-17 : ip trunk (sip) callin...

  • Page 316

    Issue 1.0 univerge sv8100 2 - 282 program 21 : outgoing call setup description use program 21-18 : ip trunk (h.323) calling party number setup for extension to assign the calling party number for each extension. The assigned number is sent to the exchange when the caller places an outgoing call. Whe...

  • Page 317

    Univerge sv8100 issue 1.0 programming manual 2 - 283 description use program 21-19 : ip trunk (sip) calling party number setup for extension to set the sip calling party number for an individual extension. Conditions none feature cross reference none program 21 : outgoing call setup 21-19 : ip trunk...

  • Page 318

    Issue 1.0 univerge sv8100 2 - 284 program 21 : outgoing call setup description use program 21-21 : toll restriction for trunks (seized trunk basis setting) to define the toll restriction class to each trunk. The details of toll restriction are defined by prg 21-05 and 21-06. This program is compared...

  • Page 319

    Univerge sv8100 issue 1.0 programming manual 2 - 285 description use program 21-22 : co message waiting indication – call back settings to define the settings of co message waiting indication. Conditions none feature cross reference r none program 21 : outgoing call setup 21-22 : co message waiting ...

  • Page 320

    Issue 1.0 univerge sv8100 2 - 286 program 21 : outgoing call setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 321

    Programming manual 2 - 287 program 22 description use program 22-01 : system options for incoming calls to define the system options for incoming calls. Program 22 : incoming call setup 22-01 : system options for incoming calls level: in input data item no. Item input data default description relate...

  • Page 322

    Issue 1.0 univerge sv8100 2 - 288 program 22 : incoming call setup conditions none feature cross reference r central office calls, answering 08 did pilot call no answer time 0~64800 (sec) 60 09 did to trunk to trunk no answer timer 0~64800 (sec) 20 10 vrs waiting message operation 0 = enable always ...

  • Page 323

    Univerge sv8100 issue 1.0 programming manual 2 - 289 description use program 22-02 : incoming call trunk setup to assign the incoming trunk type for each trunk. There is one item for each night service mode. Conditions p when connecting to t1 trunks, after changing program 22-02-01 to match the telc...

  • Page 324

    Issue 1.0 univerge sv8100 2 - 290 program 22 : incoming call setup feature cross reference r central office calls, answering digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 325

    Univerge sv8100 issue 1.0 programming manual 2 - 291 description use program 22-03 : trunk ring tone range to select the ring tone range for the trunk. The trunk uses a ring tone in the range selected when it rings an extension. Eight ring tones are available. Customize the trunk ring tones in progr...

  • Page 326

    Issue 1.0 univerge sv8100 2 - 292 program 22 : incoming call setup conditions none feature cross reference r selectable ring tones digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 327

    Univerge sv8100 issue 1.0 programming manual 2 - 293 description use program 22-04 : incoming extension ring group assignment to assign extensions to ring groups. Calls ring extensions according to ring group programming. Use program 22-05 to assign trunks to ring groups and use program 22-06 to set...

  • Page 328

    Issue 1.0 univerge sv8100 2 - 294 program 22 : incoming call setup description use program 22-05 : incoming trunk ring group assignment to assign trunks to incoming ring groups. There are 100 available ring groups. Conditions none feature cross reference r ring groups program 22 : incoming call setu...

  • Page 329

    Univerge sv8100 issue 1.0 programming manual 2 - 295 description use program 22-06 : normal incoming ring mode to define whether or not an extension should ring for the normal incoming ring mode. Conditions none feature cross reference r central office calls, answering program 22 : incoming call set...

  • Page 330: 22-07 : Dil Assignment

    Issue 1.0 univerge sv8100 2 - 296 program 22 : incoming call setup description use program 22-07 : dil assignment to assign the destination extension or department calling group for each dil incoming trunk. A dil rings an extension directly, without any other access map or ring group programming. If...

  • Page 331

    Univerge sv8100 issue 1.0 programming manual 2 - 297 description for dil delayed ringing, use program 22-08 : dil/irg no answer destination to assign the dil no answer ring group. An unanswered dil rings this group after the dil no answer time expires (program 22-01-04). Dil delayed ringing can also...

  • Page 332

    Issue 1.0 univerge sv8100 2 - 298 program 22 : incoming call setup description use program 22-09 : did basic data setup to define the basic setting of dial-in incoming calls for each trunk group. Program 22 : incoming call setup 22-09 : did basic data setup level: in input data trunk group number 00...

  • Page 333

    Univerge sv8100 issue 1.0 programming manual 2 - 299 conditions none feature cross reference r direct inward dialing (did) 08 t302 time-out operation (only overlap receiving mode) 0 = disconnect (cut) 1 = transfer (refer to program 22-12 : did intercept ring group on page 2-306 .) 0 item no. Item in...

  • Page 334

    Issue 1.0 univerge sv8100 2 - 300 program 22 : incoming call setup description use program 22-10 : did translation table setup to specify the size of the did translation tables. There are 2000 translation table entries that you can allocate among 20 translation tables. Default table program 22 : inc...

  • Page 335

    Univerge sv8100 issue 1.0 programming manual 2 - 301 conditions none feature cross reference r direct inward dialing (did) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 336

    Issue 1.0 univerge sv8100 2 - 302 program 22 : incoming call setup description use program 22-11 : did translation table number conversion to specify for each translation table entry (2000). R the digits received by the system (eight maximum) r the extension the system dials after translation (24 di...

  • Page 337

    Univerge sv8100 issue 1.0 programming manual 2 - 303 0 enter characters: 0 ! “ # $ % & ’ ( ) ô Õ ú ä ö ü dht 4 enter characters: 4 + , - . / : ; ? % ( v 6 f ¢ £ # # = accepts an entry (only required if two letters on the same key are needed - ex: tom). Pressing # again = space. (in system programmin...

  • Page 338

    Issue 1.0 univerge sv8100 2 - 304 program 22 : incoming call setup 05 transfer destination number 1 0 = no setting 1~100 = incoming group 102 = in-skin/external voice mail or inmail 201~264 = extension group 400 = valid extension number 401 = disa 501~599 = disa/vrs message 1000~1999 = speed dial nu...

  • Page 339

    Univerge sv8100 issue 1.0 programming manual 2 - 305 conditions p when the trunk type is set to 3 (did) in 22-02-01, the did transfer destination for each did feature is not supported. This feature is supported only for did trunks when assigned as vrs. Feature cross reference r direct inward dialing...

  • Page 340

    Issue 1.0 univerge sv8100 2 - 306 program 22 : incoming call setup description for each did translation table, use program 22-12 : did intercept ring group to define the first destination group for did calls. Depending on the entry in program 22-09-02 and 22-11-04, the incoming calls route to the fi...

  • Page 341

    Univerge sv8100 issue 1.0 programming manual 2 - 307 conditions none feature cross reference r direct inward dialing (did) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 342

    Issue 1.0 univerge sv8100 2 - 308 program 22 : incoming call setup description use program 22-13 : did trunk group to translation table assignment to assign the did trunk groups to did translation tables. Did trunks should be in their own group. If you have more than one type of did trunk, put each ...

  • Page 343

    Univerge sv8100 issue 1.0 programming manual 2 - 309 description use program 22-14 : vrs delayed message for irg (incoming group ring)to define for each incoming ring group the timers, vrs message number and type of tone for vrs waiting message. Program 22 : incoming call setup 22-14 : vrs delayed m...

  • Page 344

    Issue 1.0 univerge sv8100 2 - 310 program 22 : incoming call setup conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 345

    Univerge sv8100 issue 1.0 programming manual 2 - 311 description use program 22-15 : vrs delayed message for department group to define for each department (extension) group the timers, vrs message number and tone kind for vrs delayed message. There are 64 available department groups. Program 22 : i...

  • Page 346

    Issue 1.0 univerge sv8100 2 - 312 program 22 : incoming call setup conditions none feature cross reference r department group digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 347

    Univerge sv8100 issue 1.0 programming manual 2 - 313 description use program 22-16: private call refuse target area setup to define speed dial group number for private call refuse. Conditions none feature cross reference r department group program 22 : incoming call setup 22-16 : private call refuse...

  • Page 348

    Issue 1.0 univerge sv8100 2 - 314 program 22 : incoming call setup description use program 22-17: dial-in conversion table area setup for time pattern to define time zone and dial-in conversion table (program 22-11) for time pattern. Conditions none feature cross reference none program 22 : incoming...

  • Page 349

    Univerge sv8100 issue 1.0 programming manual 2 - 315 description use program 22-18: private call assignment setup to define assignment and incoming ring pattern for private calls. Conditions none feature cross reference none program 22 : incoming call setup 22-18 : private call assignment setup leve...

  • Page 350

    Issue 1.0 univerge sv8100 2 - 316 program 22 : incoming call setup description use program 22-20: flexible ringing by caller id setup to set flexible ringing by caller id per timer pattern mode. Conditions none feature cross reference none program 22 : incoming call setup 22-20 : flexible ringing by...

  • Page 351

    Programming manual 2 - 317 program 23 description use program 23-02 : call pickup groups to assign extensions to call pickup groups. This program also lets you assign an extension call pickup group priority. If two extensions in a group are ringing at the same time, group call pickup intercepts the ...

  • Page 352

    Issue 1.0 univerge sv8100 2 - 318 program 23 : answer features setup description use program 23-03 : universal answer/auto answer to assign trunk routes (set in program 14-06) to extensions for universal answer. If the call ringing the paging system is in an extension assigned route, the user can di...

  • Page 353

    Univerge sv8100 issue 1.0 programming manual 2 - 319 conditions none feature cross reference r line preference r night service digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 354

    Issue 1.0 univerge sv8100 2 - 320 program 23 : answer features setup description use program 23-04 : ringing line preference for virtual extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone. There are 256 available virtual extension ports...

  • Page 355

    Programming manual 2 - 321 program 24 description use program 24-01 : system options for hold to define the system options for the hold feature. Program 24 : hold/transfer setup 24-01 : system options for hold level: in input data item no. Item input data default related program 01 hold recall time ...

  • Page 356

    Issue 1.0 univerge sv8100 2 - 322 program 24 : hold/transfer setup conditions none feature cross reference r hold r park 06 park hold time – normal a call left parked longer than this time recalls the extension that initially parked it. 0~64800 (sec) 90 20-11-19 07 park hold time – extended (recall)...

  • Page 357

    Univerge sv8100 issue 1.0 programming manual 2 - 323 description use program 24-02 : system options for transfer to define the system options for the transfer feature. Program 24 : hold/transfer setup 24-02 : system options for transfer level: in input data item no. Item input data default related p...

  • Page 358

    Issue 1.0 univerge sv8100 2 - 324 program 24 : hold/transfer setup conditions none feature cross reference r transfer 07 trunk-to-trunk transfer release warning tone time starts when a trunk begins talking with another trunk (for example: trunk-to-trunk transfer, outgoing from trunk, tandem trunking...

  • Page 359: 24-03 : Park Group

    Univerge sv8100 issue 1.0 programming manual 2 - 325 description use program 24-03 : park group to assign an extension to a park group. The system allows a total of 64 park groups. An extension can only pick up a call parked in orbit by an extension in its own group. Conditions none feature cross re...

  • Page 360

    Issue 1.0 univerge sv8100 2 - 326 program 24 : hold/transfer setup description use program 24-04 : automatic trunk-to-trunk transfer target setup to assign the speed dialing number bin which should be used as the destination of the automatic trunk-to-trunk transfer. Conditions none feature cross ref...

  • Page 361

    Univerge sv8100 issue 1.0 programming manual 2 - 327 description use program 24-05 : department group transfer target setup to assign the speed dialing bin which is used as the destination of the extension for the extension group. There are 64 available department groups. Conditions none feature cro...

  • Page 362

    Issue 1.0 univerge sv8100 2 - 328 program 24 : hold/transfer setup description for each extension/virtual extension port, use program 24-06 : fixed call forwarding to assign the fixed call forwarding type (0~4) and the destination extension/virtual extension. For extension ports, the fixed call forw...

  • Page 363

    Univerge sv8100 issue 1.0 programming manual 2 - 329 description use program 24-07 : fixed call forward off-premise to assign the fixed call forwarding off-premise telephone number for each extension/virtual extension. The off-premise destination can be up to 24-digits long. A trunk access code (e.G...

  • Page 364

    Issue 1.0 univerge sv8100 2 - 330 program 24 : hold/transfer setup description use program 24-08 : call forward for centrex to assign the call forwarding type and call forwarding for centrex telephone number for each extension/virtual extension. The off-premise destination can be up to 24-digits lon...

  • Page 365

    Univerge sv8100 issue 1.0 programming manual 2 - 331 description use program 24-09 : call forward split settings to assign call forwarding type and the destination numbers for each extension/virtual extension. The destination can be up to 24 digits long, using 0~9, 4 , #, and @. Be sure to include t...

  • Page 366

    Issue 1.0 univerge sv8100 2 - 332 program 24 : hold/transfer setup conditions none feature cross reference r call forwarding, off-premise 06 call forwarding destination for ctx/pbx for all call, no answer: 0~9, # , 4 , r, @ (up to 24 digits) none 07 call forwarding destination for ctx/pbx for busy: ...

  • Page 367

    Programming manual 2 - 333 program 25 description use program 25-01 : vrs/disa line basic data setup to define the basic setting of each vrs/disa line. Conditions none feature cross reference r direct inward system access (disa) program 25 : vrs/disa setup 25-01 : vrs/disa line basic data setup leve...

  • Page 368

    Issue 1.0 univerge sv8100 2 - 334 program 25 : vrs/disa setup description use program 25-02 : did/disa vrs message to assign the vrs message number to be used as the automated attendant message for each trunk which is assigned as a vrs/disa. Conditions none feature cross reference r direct inward sy...

  • Page 369

    Univerge sv8100 issue 1.0 programming manual 2 - 335 description use program 25-03 : vrs/disa transfer ring group with incorrect dialing to set what happens to a call when the disa or automated attendant caller dials incorrectly or waits too long to dial. The call can either disconnect (0) or transf...

  • Page 370

    Issue 1.0 univerge sv8100 2 - 336 program 25 : vrs/disa setup description use program 25-04 : vrs/disa transfer ring group with no answer/busy to set the operating mode of each disa trunk. This sets what happens to the call when the disa or automated attendant caller calls a busy or unanswered exten...

  • Page 371

    Univerge sv8100 issue 1.0 programming manual 2 - 337 description use program 25-05 : vrs/disa error message assignment to assign the vrs message number to be used as the automated attendant error message. For each vrs/disa trunk that the vrs answers, enter the vrs message (1~100) the outside caller ...

  • Page 372

    Issue 1.0 univerge sv8100 2 - 338 program 25 : vrs/disa setup description use program 25-06 : vrs/disa one-digit code attendant setup to set up single digit dialing through the vrs. This gives vrs callers single key access to extensions, the company operator, department calling groups and voice mail...

  • Page 373

    Univerge sv8100 issue 1.0 programming manual 2 - 339 conditions p outside caller may not be able to dial individual extensions or lines if the same first digit is defined here. Feature cross reference r direct inward system access (disa) r voice response system (vrs) digitcom canada inc. Need suppor...

  • Page 374

    Issue 1.0 univerge sv8100 2 - 340 program 25 : vrs/disa setup description use program 25-07 : system timers for vrs/disa to set the value for the system timers which affect did and disa. Refer to the following chart for a description of each option, its range and default setting. Program 25 : vrs/di...

  • Page 375

    Univerge sv8100 issue 1.0 programming manual 2 - 341 conditions none feature cross reference r direct inward system access (disa) 07 long conversation warning tone time determine the time a disa caller or any trunk-to-trunk (such as tandem trunking) conversation can talk before the long conversation...

  • Page 376

    Issue 1.0 univerge sv8100 2 - 342 program 25 : vrs/disa setup description use program 25-08 : disa user id setup to set the 6-digit disa password for each user. There are 15 users each with one 6-digit password. Conditions none feature cross reference r direct inward system access (disa) program 25 ...

  • Page 377

    Univerge sv8100 issue 1.0 programming manual 2 - 343 description use program 25-09 : class of service for disa users to set the disa class of service for each user. When a disa caller enters a password (defined in program 25-08), the system identifies the user and associates the appropriate disa cla...

  • Page 378

    Issue 1.0 univerge sv8100 2 - 344 program 25 : vrs/disa setup description use program 25-10 : trunk group routing for disa to assign the trunk group route chosen when a user places a disa call to the system and dials 9. Set trunk group routing in program 14-06. Enable or disable the disa caller abil...

  • Page 379

    Univerge sv8100 issue 1.0 programming manual 2 - 345 description for systems that use toll restriction, use program 25-11 : disa toll restriction class to assign a toll restriction class (1-15) to each disa user (1~15). The system uses the toll restriction class you enter in program 21-05 and 21-06....

  • Page 380

    Issue 1.0 univerge sv8100 2 - 346 program 25 : vrs/disa setup description use program 25-12 : alternate trunk group routing for disa to define the trunk route selected when a disa caller dials the alternate trunk access code. The route selected is based on the disa caller class of service, which in ...

  • Page 381

    Univerge sv8100 issue 1.0 programming manual 2 - 347 description use program 25-13 : system option for disa to enter the password disa callers must dial before the system allows them to record, listen to and or erase the vrs messages. This program also is used to define additional disa call options....

  • Page 382

    Issue 1.0 univerge sv8100 2 - 348 program 25 : vrs/disa setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 383: Program 26 : Ars Service

    Programming manual 2 - 349 program 26 description use program 26-01 : automatic route selection service to define the system options for automatic route selection (ars). Program 26 : ars service 26-01 : automatic route selection service level: in input data item no. Item input data default related p...

  • Page 384

    Issue 1.0 univerge sv8100 2 - 350 program 26 : ars service conditions none feature cross reference r automatic route selection digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 385: Program 26 : Ars Service

    Univerge sv8100 issue 1.0 programming manual 2 - 351 description use program 26-02 : dial analysis table for ars/lcr to set pre-transaction tables for selecting automatic route selection (ars). R service type 1 (route to trunk group number) – the number routes to a trunk group. R service type 2 (f-r...

  • Page 386

    Issue 1.0 univerge sv8100 2 - 352 program 26 : ars service conditions none feature cross reference r automatic route selection 07 network specified parameter table 0~16 0 26-12 item no. Item input data default related programming digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: ww...

  • Page 387: Program 26 : Ars Service

    Univerge sv8100 issue 1.0 programming manual 2 - 353 description use program 26-03 : ars dial treatments to assign the 15 dial treatments for automatic ars dialing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial treatment options are: r 3 – delete...

  • Page 388

    Issue 1.0 univerge sv8100 2 - 354 program 26 : ars service conditions none feature cross reference r automatic route selection input data dial treatment table number 1~15 item no. Item input data default 01 treatment code 24 characters maximum no setting digitcom canada inc. Need support? Call 1-866...

  • Page 389: Program 26 : Ars Service

    Univerge sv8100 issue 1.0 programming manual 2 - 355 description use program 26-04 : ar s class of service to set the ars class of service for an extension. Automatic route selection uses ars class of service when determining how to route extension calls. Conditions none feature cross reference r au...

  • Page 390: Program 26 : Ars Service

    Issue 1.0 univerge sv8100 2 - 356 program 26 : ars service description use program 26-11 : transit network id table to define transit network id for alternate carrier access, which is referred from program 26-03. Conditions none feature cross reference none program 26 : ars service 26-11 : transit n...

  • Page 391: Program 26 : Ars Service

    Univerge sv8100 issue 1.0 programming manual 2 - 357 description use program 26-12 : network specific parameter table for ars to define the network specific parameter table. Conditions none feature cross reference none program 26 : ars service 26-12 : network specific parameter table for ars level: ...

  • Page 392

    Issue 1.0 univerge sv8100 2 - 358 program 26 : ars service this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 393

    Programming manual 2 - 359 program 30 description use program 30-01 : dss console operating mode to set the mode of the system dss consoles. The entry for this option applies to all the system dss consoles. The available options are: r regular (business) mode (0) r hotel mode (1) r acd monitor mode ...

  • Page 394

    Issue 1.0 univerge sv8100 2 - 360 program 30 : dss/dls console setup description use program 30-02 : dss console extension assignment to identify which extensions have dss consoles connected. R up to 32 different extensions with dss consoles can be set up. A single extension can have up to four 60-b...

  • Page 395

    Univerge sv8100 issue 1.0 programming manual 2 - 361 description use program 30-03 : dss console key assignments to customize the key assignments for 60-button dss consoles. A dss console key can have any function with up to four digits (e.G., extension number or service code). To prevent lamp probl...

  • Page 396

    Issue 1.0 univerge sv8100 2 - 362 program 30 : dss/dls console setup function number list [1] general functional level (00~99) function number function additional data led indication 00 --- not used --- 01 dss/one-touch extension number or any numbers (up to 24 digits) red on: extension busy off: ex...

  • Page 397

    Univerge sv8100 issue 1.0 programming manual 2 - 363 20 external all call paging red on: active 21 internal group paging internal paging number (01~64) red on: active 22 internal all call paging none 23 meet-me answer to internal paging none 24 call pickup none 25 call pickup for another group none ...

  • Page 398

    Issue 1.0 univerge sv8100 2 - 364 program 30 : dss/dls console setup 39 room monitoring rapid blink (red): under monitored slow blink (red): under monitoring with room monitor there are two parties in the monitor, one being monitored and one who is monitoring. The same key is used on both phones, bu...

  • Page 399

    Univerge sv8100 issue 1.0 programming manual 2 - 365 57 general purpose led indication 001~100: rapid blink (red) 101~200: rapid blink (green) 201~300: red on,green rapid blink 58 department incoming call – immediate extension group number (01~64) 59 department incoming call – delay extension group ...

  • Page 400

    Issue 1.0 univerge sv8100 2 - 366 program 30 : dss/dls console setup 80 tandem ringing 0 = cancel 1 = set extension number to tandem ring red on: active 81 automatic transfer to transfer key trunk line number 001~200 82 d term ip call log 83 conversation recording function 0 = pause 1 = re-record 2 ...

  • Page 401

    Univerge sv8100 issue 1.0 programming manual 2 - 367 default p the dss keys 01~60 of all dss consoles = dss/one-touch key 101~160. P the dss keys 61~114 of all dss consoles = none conditions none feature cross reference r direct station selection (dss) console 4 04 park key park number (01~64) 4 05 ...

  • Page 402

    Issue 1.0 univerge sv8100 2 - 368 program 30 : dss/dls console setup description use program 30-04 : dss console alternate answer to assign the alternate dss console station in case off-duty mode is set (by pressing the alt key on the dss console). Conditions p related extension is assigned in prg30...

  • Page 403

    Univerge sv8100 issue 1.0 programming manual 2 - 369 description use program 32-05 : dss console lamp table to define the led patterns for functions on the dss consoles. Program 30 : dss/dls console setup 30-05 : dss console lamp table level: in input data item no. Item lamp pattern data default 02 ...

  • Page 404

    Issue 1.0 univerge sv8100 2 - 370 program 30 : dss/dls console setup table 2-9 led patterns for dss console conditions none feature cross reference r direct station selection (dss) console digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 405

    Univerge sv8100 issue 1.0 programming manual 2 - 371 description use program 30-10 : dss console ip terminal setup to set the mac address for a particular ip dss console. This must be done before the console can be associated to the attendant phone. The system supports up to 32 ip dss consoles. Cond...

  • Page 406

    Issue 1.0 univerge sv8100 2 - 372 program 30 : dss/dls console setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 407

    Programming manual 2 - 373 program 31 description use program 31-01 : system options for internal/external paging to define the system options for internal/external paging. The system shows the name you program on the telephone display. Use the following chart when entering and editing text. When us...

  • Page 408

    Issue 1.0 univerge sv8100 2 - 374 program 31 : paging setup conditions none feature cross reference r paging, external r paging, internal 4 enter characters: 4 + , - . / : ; ? % ( v 6 f ¢ £ # # = accepts an entry (only required if two letters on the same key are needed - ex: tom). Pressing # again =...

  • Page 409

    Univerge sv8100 issue 1.0 programming manual 2 - 375 description use program 31-02 : internal paging group assignment to assign extensions to internal paging groups (i.E., page zones). The setting in this program also determines if the internal page group can receive internal all call paging. The sy...

  • Page 410

    Issue 1.0 univerge sv8100 2 - 376 program 31 : paging setup description use program 31-03 : internal paging group settings to assign names to internal paging groups (i.E., page zones) and to define the splash tone for internal paging. The system shows the names you program on the telephone display. ...

  • Page 411

    Univerge sv8100 issue 1.0 programming manual 2 - 377 default item 01 : internal paging group name # # = accepts an entry (only required if two letters on the same key are needed - ex: tom). Pressing # again = space. (in system programming mode, use the right arrow soft key instead to accept and/or a...

  • Page 412

    Issue 1.0 univerge sv8100 2 - 378 program 31 : paging setup conditions none feature cross reference r paging, internal digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 413

    Univerge sv8100 issue 1.0 programming manual 2 - 379 description use program 31-04 : external paging zone group to assign each external paging zone to an external paging group. Users call the external paging group when broadcasting announcements to the external zone. When programming, the zones on t...

  • Page 414

    Issue 1.0 univerge sv8100 2 - 380 program 31 : paging setup description use program 31-05 : universal night answer/ring over page to assign universal night answer ringing to each external paging zone. For each trunk port, make a separate entry for each external paging zone. When programming, the zon...

  • Page 415

    Univerge sv8100 issue 1.0 programming manual 2 - 381 description use program 31-06 : external speaker control to define the settings for the external speaker using an amplifier. Program 31 : paging setup 31-06 : external speaker control level: in input data external speaker number 1~9 item no. Item ...

  • Page 416

    Issue 1.0 univerge sv8100 2 - 382 program 31 : paging setup conditions none feature cross reference r paging, external digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 417

    Univerge sv8100 issue 1.0 programming manual 2 - 383 description use program 31-07 : combined paging assignments to assign an external paging group (0~8) to an internal paging zone (0~64) for combined paging. When an extension user makes a combined page, they simultaneously broadcast into both the e...

  • Page 418

    Issue 1.0 univerge sv8100 2 - 384 program 31 : paging setup description use program 31-08 : bgm on external paging to set the background music option for each external paging zone. If enabled, the system plays background music over the zone when it is idle. When programming, the zones on the pgd(2)-...

  • Page 419

    Programming manual 2 - 385 program 32 description use program 32-01 : door box timers setup to assign the timers used for the door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Conditions none feature cross reference r door box program 32 ...

  • Page 420

    Issue 1.0 univerge sv8100 2 - 386 program 32 : door box and sensor setup description use program 32-02 : door box ring assignment to assign the extension which rings when a caller presses the associated door box call button. The door box feature is called door phone when programming via webpro and u...

  • Page 421

    Univerge sv8100 issue 1.0 programming manual 2 - 387 description use program 32-03 : door box basic setup to select the chime pattern and gain level for each door box. There are six distinctive chime patterns. The chime tones are defined in 80-01 : service tone setup on page 2-583 . The door box fea...

  • Page 422

    Issue 1.0 univerge sv8100 2 - 388 program 32 : door box and sensor setup description use program 32-04 : door box name setup to define the name of each door box. The door box feature is called door phone when programming via webpro and using a multiline terminal. Conditions none feature cross refere...

  • Page 423

    Programming manual 2 - 389 program 33 description use program 33-01 : aci port type setup to set the function of each software port on an analog communications interface. Each aci software port can have only one function (input, output or none). Conditions none feature cross reference r analog commu...

  • Page 424

    Issue 1.0 univerge sv8100 2 - 390 program 33 : cta and aci setup description use program 33-02 : aci department calling group to assign aci ports to department groups. An aci port can be in only one group. Also use this program to set the aci port priority. When a call comes into the aci department ...

  • Page 425

    Programming manual 2 - 391 program 34 description use program 34-01 : e&m tie line basic setup to define the basic settings for each e&m tie line. Program 34 : tie line setup 34-01 : e&m tie line basic setup level: in input data trunk port number 001~200 item no. Item input data default description ...

  • Page 426

    Issue 1.0 univerge sv8100 2 - 392 program 34 : tie line setup conditions none feature cross reference r tie lines digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 427

    Univerge sv8100 issue 1.0 programming manual 2 - 393 description use program 34-02 : e&m tie line class of service to assign a class of service to a tie line (there are 15 tie line classes of service). The class of service options are defined in program 20-14. For each tie line, make a separate entr...

  • Page 428

    Issue 1.0 univerge sv8100 2 - 394 program 34 : tie line setup description use program 34-03 : trunk group routing for e&m tie lines to assign the trunk group route 1~8 or 1~100) chosen when a user seizes a tie line and dials 9. (set trunk group routing in program 14-07.) if the system has automatic ...

  • Page 429

    Univerge sv8100 issue 1.0 programming manual 2 - 395 description use program 34-04 : e&m tie line toll restriction class to enter a toll restriction class for each tie line. There are 15 toll restriction classes which are defined in programs 21-05 and 21-06. For each tie line, you make a separate to...

  • Page 430

    Issue 1.0 univerge sv8100 2 - 396 program 34 : tie line setup description use program 34-05 : tie line outgoing call restriction to build a restriction matrix for outgoing trunk calls placed from an inbound trunk (e.G., dialed from a tie line). For each inbound trunk group, enable or disable access ...

  • Page 431

    Univerge sv8100 issue 1.0 programming manual 2 - 397 description use program 34-06 : add/delete digit for e&m tie line to set digits that the system should add or delete for tie lines. R delete digit some tie line networks pass the location number and extension number to the remote side. This progra...

  • Page 432

    Issue 1.0 univerge sv8100 2 - 398 program 34 : tie line setup description use program 34-07 : e&m tie line timer to define the system service tone timers. Conditions p if prg 34-07-05 is left at default (30) the transferred call recalls to the station that performed the transfer when not answered. F...

  • Page 433

    Univerge sv8100 issue 1.0 programming manual 2 - 399 description use program 34-08 : toll restriction data for e&m tie lines to define the toll restriction data for e&m tie lines. This data should be defined if tie line toll restriction is enabled in program 21-05-13. Conditions none feature cross r...

  • Page 434

    Issue 1.0 univerge sv8100 2 - 400 program 34 : tie line setup description use program 34-09 : ani/dnis service options to define the ani//dnis service option setup for e&m class of service. Program 34 : tie line setup 34-09 : ani/dnis service options level: in input data class of service 01~15 item ...

  • Page 435

    Univerge sv8100 issue 1.0 programming manual 2 - 401 04 route table setup of target dial the option sets how the system uses the route data (gathered in item 3) to route incoming ani/dnis calls. If option 2 is selected, and the call is to be routed using the did table (1), up to 8 digits can be matc...

  • Page 436

    Issue 1.0 univerge sv8100 2 - 402 program 34 : tie line setup conditions none feature cross reference r t1 trunking (with ani/dnis compatibility) r tie lines 08 routing when destination busy or no answer this option lets you determine how the system handles an ani/dnis call if destination is busy or...

  • Page 437

    Univerge sv8100 issue 1.0 programming manual 2 - 403 description use program 34-10 : digits delete for t1 ani assignment to delete the information digits received from the network on feature group d trunks. Conditions none feature cross reference r t1 trunking (with ani/dnis ability) example: progra...

  • Page 438

    Issue 1.0 univerge sv8100 2 - 404 program 34 : tie line setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 439: 35-01 : Smdr Options

    Programming manual 2 - 405 program 35 description use program 35-01 : smdr options to set the smdr (station message detail recording) options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range and default setting. Program 35 : smdr account code...

  • Page 440

    Issue 1.0 univerge sv8100 2 - 406 program 35 : smdr account code setup conditions none feature cross reference r station message detail recording 06 minimum call duration the duration of the call must be at least this time to be included on the smdr report. 0~65535 (sec) (0 = all) 0 07 minimum ring ...

  • Page 441

    Univerge sv8100 issue 1.0 programming manual 2 - 407 description use program 35-02 : smdr output options to set the smdr (station message detail recording) output options for each of the eight smdr ports. Refer to the following chart for a description of each option, its range and default setting. P...

  • Page 442

    Issue 1.0 univerge sv8100 2 - 408 program 35 : smdr account code setup 07 toll charge cost set this option to (1) have the smdr report include toll charges. 0 = not displayed 1 = displayed 1 08 incoming call enable this option (1) to have the smdr report include incoming calls. If you disable this o...

  • Page 443

    Univerge sv8100 issue 1.0 programming manual 2 - 409 conditions none feature cross reference r station message detail recording 18 print mode for caller name of incoming call determine how smdr should print caller name of incoming call. 0 = normal 1 = line feed 0 item no. Item input data default dig...

  • Page 444

    Issue 1.0 univerge sv8100 2 - 410 program 35 : smdr account code setup description use program 35-03 : smdr port assignment for trunk group to assign the smdr port for each trunk group. For each trunk group, select the smdr port where the incoming smdr information should be sent. Conditions none fea...

  • Page 445

    Univerge sv8100 issue 1.0 programming manual 2 - 411 description use program 35-04 : smdr port assignment for department groups to assign the smdr port for each department group. For each department group, select the smdr port where the outgoing smdr information should be sent. There are 64 availabl...

  • Page 446

    Issue 1.0 univerge sv8100 2 - 412 program 35 : smdr account code setup description use program 35-05 : account code setup to set various account code options for an extension class of service. Assign a class of service to extensions in program 20-06. Program 35 : smdr account code setup 35-05 : acco...

  • Page 447

    Univerge sv8100 issue 1.0 programming manual 2 - 413 conditions none feature cross reference r account codes digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 448

    Issue 1.0 univerge sv8100 2 - 414 program 35 : smdr account code setup description use program 35-06 : verified account code table to enter account codes into the verified account code list. You can enter up to 2000 codes with 3~6 digits, using the characters 0~9 or # . Use the lk1 to enter a wild c...

  • Page 449

    Programming manual 2 - 415 program 40 description use program 40-01 : voice mail basic setup to define the basic operation of voice mail. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recording system 40-01 : voice mail basic setup level: in input data ...

  • Page 450: 40-02 : Mailbox Setup

    Issue 1.0 univerge sv8100 2 - 416 program 40 : voice recording system description use program 40-02 : mailbox setup to define the mailbox of the voice mail. There are a maximum of 500 mailboxes. Use this program to set the box number and password linked to the extension number (or pilot number) for ...

  • Page 451

    Univerge sv8100 issue 1.0 programming manual 2 - 417 description use program 40-03 : message recording setup to define the auto-answering operation of the voice mail. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recording system 40-03 : message recordi...

  • Page 452

    Issue 1.0 univerge sv8100 2 - 418 program 40 : voice recording system description use program 40-04 : live recording setup to define the conversation recording operation of the voice mail. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recording system 4...

  • Page 453

    Univerge sv8100 issue 1.0 programming manual 2 - 419 description use program 40-05 : call information setup to define the incoming notice of the voice mail. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recording system 40-05 : call information setup le...

  • Page 454

    Issue 1.0 univerge sv8100 2 - 420 program 40 : voice recording system description use program 40-06 : voice mail automated attendant data setup to define the outside lines to use the automated attendant recording operation of the voice mail. Conditions none feature cross reference r voice mail integ...

  • Page 455

    Univerge sv8100 issue 1.0 programming manual 2 - 421 description use program 40-07 : voice prompt language assignment for vrs to specify the language to be used for the vrs prompts. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recording system 40-07 : ...

  • Page 456

    Issue 1.0 univerge sv8100 2 - 422 program 40 : voice recording system description use program 40-08 : voice prompt language assignment for mailboxes to select the language to be used for the mailboxes. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recor...

  • Page 457

    Univerge sv8100 issue 1.0 programming manual 2 - 423 description use program 40-09 : voice mail multiple address group setup to define the broadcast group of a voice mail mailbox. Conditions none feature cross reference r voice mail integration (analog) program 40 : voice recording system 40-09 : vo...

  • Page 458

    Issue 1.0 univerge sv8100 2 - 424 program 40 : voice recording system description in program 40-10 : voice announcement service option define the system options for the voice announcement feature. Program 40 : voice recording system 40-10 : voice announcement service option level: in input data item...

  • Page 459

    Univerge sv8100 issue 1.0 programming manual 2 - 425 conditions none feature cross reference r voice response system (vrs) 07 set vrs message for caller id refuse (vrs msg cid) this item assigns the vrs message number to be used as caller id refuse. When fixed message is set, vrs message guidance is...

  • Page 460

    Issue 1.0 univerge sv8100 2 - 426 program 40 : voice recording system description in program 40-11 : preamble message assignment to assign the vrs message number to be used as the preamble message for each trunk. When the extension user answers the incoming call, the assigned vrs message is sent to ...

  • Page 461: Program 41 : Acd Setup

    Programming manual 2 - 427 program 41 description in program 41-01 : system options for acd define the system options for the acd feature. Conditions none feature cross reference r automatic call distribution (acd) program 41 : acd setup 41-01 : system options for acd level: in input data item no. I...

  • Page 462: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 428 program 41 : acd setup description in program 41-02 : acd group and agent assignments, for each acd extension number, assign an acd group (1~64). An acd group number is assigned to each work period number (1~8). The assigned extension will work as an acd agent exten...

  • Page 463: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 429 description in program 41-03 : incoming ring group assignment for acd group, for each incoming trunk group set up in program 22-05, designate which acd group (1~64) the trunks should ring for each of the eight work periods. Also use this program t...

  • Page 464

    Issue 1.0 univerge sv8100 2 - 430 program 41 : acd setup conditions none feature cross reference r automatic call distribution (acd) r ring groups digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 465: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 431 description for each acd group (1~64), use program 41-04 : acd group supervisor to assign the group supervisor extension and operating mode. Operating modes are: r 0 = supervisor extension does not receive acd group calls. R 1 = supervisor extensi...

  • Page 466: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 432 program 41 : acd setup description use program 41-05 : acd agent work schedules to set up the work schedules for acd agents and groups. For each acd work schedule (1~4), designate the start and stop times for each of the eight work periods. After you set up the sche...

  • Page 467: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 433 description use program 41-06 : trunk work schedules to set up the work schedules for trunks. For each work schedule (1~4), designate the start and stop times for each of the eight work periods. After you set up the schedules, assign them to days ...

  • Page 468: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 434 program 41 : acd setup description use program 41-07 : acd weekly schedule setup to assign the four work schedules (1~4) to days of the week. The assignments you make in this program apply to both the acd agent work schedules (program 41-05) and the trunk work sched...

  • Page 469: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 435 description for each acd group (1~64), use program 41-08 : acd overflow options to assign the overflow mode (0~9), destination and announcement message types. Delay announcement functions are not available for acd pilot number calls. Each acd grou...

  • Page 470

    Issue 1.0 univerge sv8100 2 - 436 program 41 : acd setup conditions none feature cross reference r automatic call distribution (acd) 06 incoming ring group when overflow 1~100 (used when 41-08-02 is set to 68) 1 item no. Item input data default digitcom canada inc. Need support? Call 1-866-667-8357 ...

  • Page 471: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 437 description use program 41-09 : acd overflow table setting to define the acd group to which a call is transferred when overflow occurs. Conditions none feature cross reference r automatic call distribution (acd) program 41 : acd setup 41-09 : acd ...

  • Page 472: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 438 program 41 : acd setup description use program 41-10 : aci delay announcement to define the aci port number to be used for the delay announcement. This program is activated when the delay announcement source and options are assigned as aci in program 41-08-03. Condi...

  • Page 473: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 439 description use program 41-11 : vrs delay announcement to assign the vrs message number to be used as the message source for the 1st and 2nd delay announcement messages. Refer to program 41-08 for more on setting up the acd overflow options. This ...

  • Page 474

    Issue 1.0 univerge sv8100 2 - 440 program 41 : acd setup conditions none feature cross reference r automatic call distribution (acd) 08 queue depth announcement input when the queue depth announcement will be played. 0 = disable 1 = after 1st (1st) 2 = after 2nd (2nd) 3 = after 1st and 2nd (1st and ...

  • Page 475: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 441 description use program 41-12 : night announcement setup to define the night announce voice resource and sending time for each acd group. Night announcement availability depends on the setting in program 41-03-02. The night announcement function i...

  • Page 476: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 442 program 41 : acd setup description use program 41-13 : vrs message number for night announcement to define the vrs message number to be used as the night announcement. This program is activated when the night announcement source is assigned as vrs in program 41-12-0...

  • Page 477: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 443 description use program 41-14 : acd options setup to set various options for acd groups. When you set an option for an acd group, the setting is in force (if applicable) for all agents in the group. The chart below shows each of the acd options, t...

  • Page 478

    Issue 1.0 univerge sv8100 2 - 444 program 41 : acd setup 07 automatic off duty for slt enable/disable automatic off duty (rest) mode for agents with slt. 0 = no change to off duty mode 1 = change to off duty mode automatically (skip) 0 08 acd off duty mode enable (1) or disable (0) the ability to re...

  • Page 479

    Univerge sv8100 issue 1.0 programming manual 2 - 445 conditions none feature cross reference r automatic call distribution (acd) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 480: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 446 program 41 : acd setup description use program 41-15 : acd queue alarm information to assign the options for audible indication for log out/off duty mode for each acd group. These program settings provide an alarm to the agents, but no queue status display is indica...

  • Page 481

    Univerge sv8100 issue 1.0 programming manual 2 - 447 conditions none feature cross reference r automatic call distribution (acd) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 482: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 448 program 41 : acd setup description use program 41-16 : acd threshold overflow to define the value of the acd threshold call overflow and the mode for each acd group. Conditions none feature cross reference r automatic call distribution (acd) program 41 : acd setup 4...

  • Page 483: Program 41 : Acd Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 449 description use program 41-17 : acd login mode setup to define the acd login mode for each extension. If the aic login mode is enabled, set the aic login and aic logout service codes for the aic members in program 11-13-08 and 11-13-09. Conditions...

  • Page 484: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 450 program 41 : acd setup description use program 41-18 : acd agent identity code setup to define the acd agent identity code table. Program 41 : acd setup 41-18 : acd agent identity code setup level: sa input data aic table no. 001~512 item no. Item input data default...

  • Page 485

    Univerge sv8100 issue 1.0 programming manual 2 - 451 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 486: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 452 program 41 : acd setup description use program 41-19 : acd voice mail delay announcement to assign inmail master mailboxes (prg 47-03) as acd delay “announcement” mailboxes. Program 41 : acd setup 41-19 : acd voice mail delay announcement level: sa input data acd gr...

  • Page 487

    Univerge sv8100 issue 1.0 programming manual 2 - 453 conditions none feature cross reference none 08 delay message interval time sets the timer for the interval between the delay messages. 0 ~ 64800 (sec) 20 item no. Item input data default digitcom canada inc. Need support? Call 1-866-667-8357 visi...

  • Page 488: Program 41 : Acd Setup

    Issue 1.0 univerge sv8100 2 - 454 program 41 : acd setup description use program 41-20 : acd queue display settings to assign the options for the acd queue status display feature. This program allows the queue status display, and causes an alarm to sound, when the parameters in this program are met....

  • Page 489

    Univerge sv8100 issue 1.0 programming manual 2 - 455 conditions none feature cross reference r automatic call distribution (acd) input data acd group no. 01~64 item no. Item input data default 01 number of calls in queue set the number of calls that can accumulate in the acd queue before the queue s...

  • Page 490

    Issue 1.0 univerge sv8100 2 - 456 program 41 : acd setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 491: Program 42 : Hotel Setup

    Programming manual 2 - 457 program 42 description use program 42-01 : system options for hotel/motel to assign the system options for hotel/motel service. Conditions none feature cross reference r hotel/motel program 42 : hotel setup 42-01 : system options for hotel/motel level: in input data item n...

  • Page 492: Program 42 : Hotel Setup

    Issue 1.0 univerge sv8100 2 - 458 program 42 : hotel setup description use program 42-02 : hotel/motel telephone setup to define the basic operation of the hotel/motel extensions. Conditions none feature cross reference r hotel/motel program 42 : hotel setup 42-02 : hotel/motel telephone setup level...

  • Page 493: Program 42 : Hotel Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 459 description use program 42-03 : class of service options (hotel/motel) to set the hotel/motel class of service (cos) options. Assign class of service to extensions in program 42-02 : hotel/motel telephone setup. There are 15 classes of service. Re...

  • Page 494

    Issue 1.0 univerge sv8100 2 - 460 program 42 : hotel setup conditions none feature cross reference r class of service r hotel/motel 10 wake up call setting for own extension 0 = off 1 = on 0 0 11 change room status for own extension 0 = off 1 = on 0 0 12 slt room monitor enable (1) or disable (0) a ...

  • Page 495: Program 42 : Hotel Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 461 description use program 42-04 : hotel mode one-digit service codes to set up the hotel mode one-digit service codes which are assigned in 42-02-01. For each department calling group (1~64), you enter the destination for each single digit code (1~9...

  • Page 496: Program 42 : Hotel Setup

    Issue 1.0 univerge sv8100 2 - 462 program 42 : hotel setup description use program 42-05 : hotel room status printer to set the cta port to output the hotel data (check-out sheet, room status, etc.) and the output options for the hotel/ motel feature. Conditions p room status reports output via a ct...

  • Page 497: Program 42 : Hotel Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 463 description use program 42-06 : pms service setting to set the pms integration settings when using pms-u10 and pms feature. Conditions none feature cross reference r hotel/motel program 42 : hotel setup 42-06 : pms service setting level: in input ...

  • Page 498: Program 42 : Hotel Setup

    Issue 1.0 univerge sv8100 2 - 464 program 42 : hotel setup description use program 42-07 : pms restriction level conversion table to change the default toll restriction class on check in for a room (prg 42-02-02). Conditions none feature cross reference r hotel/motel program 42 : hotel setup 42-07 :...

  • Page 499

    Programming manual 2 - 465 program 44 description use program 44-01 : system options for ars/f-route to define the system options for the ars/f-route feature. Conditions none feature cross reference r automatic route selection (ars) r uniform numbering network program 44 : ars/f-route setup 44-01 : ...

  • Page 500

    Issue 1.0 univerge sv8100 2 - 466 program 44 : ars/f-route setup description use program 44-02 : dial analysis table for ars/f-route access to set the pre-transaction table for selecting ars/f-route. Program 44 : ars/f-route setup 44-02 : dial analysis table for ars/f-route access level: in input da...

  • Page 501

    Univerge sv8100 issue 1.0 programming manual 2 - 467 conditions none feature cross reference r automatic route selection (ars) 03 additional data for the service type selected in 44-02-02, enter the additional data required. P 1: delete digit = 0~255 (255 = delete all digits) p 2: [program 44-01 : 0...

  • Page 502

    Issue 1.0 univerge sv8100 2 - 468 program 44 : ars/f-route setup description when program 44-02-02 is set to type 3, use program 44-03 : dial analysis extension table to set the dial extension analysis table. These tables are used when the analyzed digits must be more than eight digits. If the recei...

  • Page 503

    Univerge sv8100 issue 1.0 programming manual 2 - 469 conditions none feature cross reference r automatic route selection (ars) dial analysis table number : 251 item no. Item input data default 03 ars/f-route select table number 0~500 (ars/f-route table number) with program 44-01 set to 0, program 44...

  • Page 504

    Issue 1.0 univerge sv8100 2 - 470 program 44 : ars/f-route setup description use program 44-04 : ars/f-route selection for time schedule to assign each ars/ f-route selection number to an ars/f-route table number for each ars/f-route time mode. There are eight time modes for ars/f-route access. Cond...

  • Page 505: 44-05 : Ars/f-Route Table

    Univerge sv8100 issue 1.0 programming manual 2 - 471 description use program 44-05 : ars/f-route table to set the ars/f-route table. There are four kinds of order. If the higher priority trunk groups are busy, the next order group is used. If a lower priority route is selected, the caller may be not...

  • Page 506

    Issue 1.0 univerge sv8100 2 - 472 program 44 : ars/f-route setup conditions none feature cross reference r automatic route selection (ars) 08 dial treatment select the dial treatment to be used for the table. If a dial treatment is selected, programs 44-05-02 and 44-05-03 are ignored and the dial tr...

  • Page 507

    Univerge sv8100 issue 1.0 programming manual 2 - 473 description use program 44-06 : additional dial table to set the additional dial table to add prior to the dialed ars/f-route number. The additional dial table used is determined in program 44-05-03. Conditions none feature cross reference r autom...

  • Page 508

    Issue 1.0 univerge sv8100 2 - 474 program 44 : ars/f-route setup description use program 44-07 : gain table for ars/f-route access to set the gain/pad table. If an extension dials ars/f-route number: r the extension dial gain table, assigned in program 44-05, is activated. R the extension dial gain ...

  • Page 509

    Univerge sv8100 issue 1.0 programming manual 2 - 475 conditions none feature cross reference r automatic route selection (ars) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 510

    Issue 1.0 univerge sv8100 2 - 476 program 44 : ars/f-route setup description use program 44-08 : time schedule for ars/f-route to define the daily pattern of the ars/f-route feature. Ars/f-route has 10 time patterns. These patterns are used in program 44-09 and 44-10. The daily pattern consists of 2...

  • Page 511

    Univerge sv8100 issue 1.0 programming manual 2 - 477 conditions none feature cross reference r automatic route selection (ars) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 512

    Issue 1.0 univerge sv8100 2 - 478 program 44 : ars/f-route setup description use program 44-09 : weekly schedule for ars/f-route to define a weekly schedule for using ars/f-route. The pattern number is defined in program 44-08-01. Conditions none feature cross reference r automatic route selection (...

  • Page 513

    Univerge sv8100 issue 1.0 programming manual 2 - 479 description use program 44-10 : holiday schedule for ars/f-route to define a yearly schedule for ars/f-route. This schedule is used for setting special days such as national holidays. The pattern number is defined in program 44-08-01. Conditions n...

  • Page 514

    Issue 1.0 univerge sv8100 2 - 480 program 44 : ars/f-route setup this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 515

    Programming manual 2 - 481 program 45 description use program 45-01 : voice mail integration options to customize certain voice mail integration options. Program 45 : voice mail integration 45-01 : voice mail integration options level: in input data item no. Item input data default 01 voice mail dep...

  • Page 516

    Issue 1.0 univerge sv8100 2 - 482 program 45 : voice mail integration conditions none feature cross reference r voice mail integration (analog) 08 centralized voice mail department group number assigns which extension (department) group number is to be assigned as the centralized voice mail group. 0...

  • Page 517: 45-02 : Nsl Option Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 483 description use program 45-02 : nsl option setup to setup the nsl options for voice mail integration . Conditions none feature cross reference none program 45 : voice mail integration 45-02 : nsl option setup level: in input data item no. Item inp...

  • Page 518

    Issue 1.0 univerge sv8100 2 - 484 program 45 : voice mail integration description use program 45-04 : voice mail digit add assignment to define the digits to add. Conditions none feature cross reference none program 45 : voice mail integration 45-04 : voice mail digit add assignment level: in input ...

  • Page 519: Signal

    Univerge sv8100 issue 1.0 programming manual 2 - 485 description use program 45-05 : voice mail send protocol signal without additional digits to send trunk number and/or station number information if integrating to voice mail when prg 45-04-xx is left blank and 45-01-15 is set to "program". Conditi...

  • Page 520

    Issue 1.0 univerge sv8100 2 - 486 program 45 : voice mail integration this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 521: Program 47 : Inmail

    Programming manual 2 - 487 program 47 description use program 47-01 : vm8000 inmail system options to set up the vm8000 inmail system-wide options. Program 47 : inmail 47-01 : vm8000 inmail system options level: in input data item no. Item input data default 02 vm8000 inmail master name (mastername)...

  • Page 522

    Issue 1.0 univerge sv8100 2 - 488 program 47 : inmail 03 subscriber message length (subs msg length) use this option to set the maximum length of recorded messages for: p subscriber mailbox users dialing rs to record and send a message. P extension users leaving a message in a subscriber mailbox. P ...

  • Page 523

    Univerge sv8100 issue 1.0 programming manual 2 - 489 05 message backup/go ahead time (msg bkup/adv time) use this option to set the backup/ go ahead interval. This time sets how far vm8000 inmail backs up when a user dials b while listening to a message. This interval also sets how far vm8000 inmail...

  • Page 524

    Issue 1.0 univerge sv8100 2 - 490 program 47 : inmail 08 delay in dialing digital pager callback number (pager dial delay) use this option to set the delay (0~99 seconds) that occurs just before vm8000 inmail dials the digital pager callback number portion of the message notification callout number ...

  • Page 525

    Univerge sv8100 issue 1.0 programming manual 2 - 491 09 wait between digital pager callout attempts (notify pager intvl) use this option to set the minimum time (1~255 minutes) between unacknowledged or unanswered digital pager message notification callouts. (a subscriber acknowledges a digital page...

  • Page 526

    Issue 1.0 univerge sv8100 2 - 492 program 47 : inmail 12 wait between rna non-pager callout attempts (notify rna intvl) use this option to set how long vm8000 inmail waits (1~255 minutes), after it dials an unanswered non-pager callout destination, before retrying the callout number. There are 3 typ...

  • Page 527

    Univerge sv8100 issue 1.0 programming manual 2 - 493 14 number of callout attempts (notify call attmpt) use this option to set how many times (1~99 attempts) vm8000 inmail retries an incomplete message notification callout. This total includes unacknowledged callouts, callouts to a busy destination,...

  • Page 528

    Issue 1.0 univerge sv8100 2 - 494 program 47 : inmail conditions p when changing 47-01-01 or 47-01-02, a system reset is required for the new setting to take effect. Feature cross reference none 19 record pad control (for networking) 1~63 (-15dbm~ +15dbm) 32 input data item no. Item input data defau...

  • Page 529: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 495 description use 47-02 : vm8000 inmail station mailbox options to set up a station/extension mailbox. Station mailboxes are automatically assigned as subscriber mailboxes. Normally, vm8000 inmail station mailbox numbers 1~26 should correspond to ex...

  • Page 530

    Issue 1.0 univerge sv8100 2 - 496 program 47 : inmail 03 number of messages use this option to set the maximum number of messages that can be left in the subscriber mailbox. If a caller tries to leave a message after this limit is reached, they hear: “that mailbox is full.” vm8000 inmail then hangs ...

  • Page 531

    Univerge sv8100 issue 1.0 programming manual 2 - 497 07 recording conversation beep (rec conv beep) use this option to enable or disable the conversation record beep. If enabled, all parties on a call hear the voice prompt “recording”, followed by a single beep when the extension user initiates conv...

  • Page 532

    Issue 1.0 univerge sv8100 2 - 498 program 47 : inmail 10 forced unscreened transfer (forced utrf) use this option to enable or disable automated attendant forced unscreened transfer for the subscriber mailbox. If enabled, each screened transfer (trf) to the extension is converted to an unscreened tr...

  • Page 533

    Univerge sv8100 issue 1.0 programming manual 2 - 499 17 enable paging 0 = no (disabled) 1 = yes (enabled) 0 18 paging option 0 = rna 1 = immediately 0 19 telephone user interface type 0 = numeric 1 = mnemonic 0 20 enable e-mail notification (not supported in v1000) 0 = no 1 = yes 0 21 e-mail address...

  • Page 534

    Issue 1.0 univerge sv8100 2 - 500 program 47 : inmail conditions none feature cross reference none 18 = reserved 19 = reserved 20 = flexible table 2-10 47-02-16 default table item name input data digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 535: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 501 description use 47-03 : vm8000 inmail group mailbox options to set up the 32 group mailboxes (01~32). A group mailbox is used for department group overflow and can be a subscriber or call routing. Program 47 : inmail 47-03 : vm8000 inmail group ma...

  • Page 536

    Issue 1.0 univerge sv8100 2 - 502 program 47 : inmail conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 537: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 503 description use 47-06 : group mailbox subscriber options to set up a master mailbox assigned as a subscriber mailbox in 47-03-03: master mailbox type. Program 47 : inmail 47-06 : group mailbox subscriber options level: in input data item no. Item ...

  • Page 538

    Issue 1.0 univerge sv8100 2 - 504 program 47 : inmail 05 recording conversation beep (rec conv beep) use this option to enable or disable the conversation record beep. If enabled, all parties on a call hear the voice prompt “recording”, followed by a single beep when the extension user initiates con...

  • Page 539

    Univerge sv8100 issue 1.0 programming manual 2 - 505 08 forced unscreened transfer (forced utrf) use this option to enable or disable automated attendant forced unscreened transfer for the subscriber mailbox. If enabled, each screened transfer (trf) to the extension is converted to an unscreened tra...

  • Page 540

    Issue 1.0 univerge sv8100 2 - 506 program 47 : inmail 14 voice prompt language refer to table 2-11 47- 06-14 default table . 1 15 enable paging 0 = no 1 = yes 0 16 paging option 0 = rna 1 - immediate 0 17 telephone user interface 0 = numeric interface 1 = mnemonic interface 2 = octel (future) 0 18 -...

  • Page 541

    Univerge sv8100 issue 1.0 programming manual 2 - 507 conditions none feature cross reference none table 2-11 47-06-14 default table item name input data 47-06-14 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = la...

  • Page 542: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 508 program 47 : inmail description use 47-07 : vm8000 inmail routing mailbox options to set up the 32 routing mailboxes. Routing mailboxes can be either announcement or call routing mailboxes. Program 47 : inmail 47-07 : vm8000 inmail routing mailbox options level: in ...

  • Page 543

    Univerge sv8100 issue 1.0 programming manual 2 - 509 conditions none feature cross reference none table 2-12 47-07-03 default table item name input data 47-07-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = la...

  • Page 544: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 510 program 47 : inmail description use 47-08 : call routing mailbox options to set the options for mailboxes assigned as call routing mailboxes in 47-07-02: routing mailbox type. Program 47 : inmail 47-08 : call routing mailbox options level: in input data routing mail...

  • Page 545

    Univerge sv8100 issue 1.0 programming manual 2 - 511 conditions none feature cross reference none 04 fax detection use this option to enable or disable fax detection for the call routing mailbox. In enabled, the vm8000 inmail automated attendant (when using this call routing mailbox) detects incomin...

  • Page 546: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 512 program 47 : inmail description use 47-09 : announcement mailbox options to set the options for mailboxes assigned as announcement mailboxes in 47-07-02 : routing mailbox type. Program 47 : inmail 47-09 : announcement mailbox options level: in input data routing mai...

  • Page 547

    Univerge sv8100 issue 1.0 programming manual 2 - 513 conditions none feature cross reference none 03 hang up after (hangup) use this option along with next call routing mailbox and repeat count above to provide additional routing options to automated attendant callers. For more detail on this intera...

  • Page 548: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 514 program 47 : inmail description use 47-10 : vm8000 inmail trunk options to assign vm8000 inmail options for each trunk. Currently, only 47-10-01: answer table assignment is available. Program 47 : inmail 47-10 : vm8000 inmail trunk options level: in input data trunk...

  • Page 549

    Univerge sv8100 issue 1.0 programming manual 2 - 515 conditions none feature cross reference none table 2-13 47-10-03 default table item name input data 47-10-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = la...

  • Page 550: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 516 program 47 : inmail description use 47-11 : vm8000 inmail answer table options to set options for the answer tables. Vm8000 inmail provides eight answer tables (1~8). To set up the schedules for each answer table, go to 47-12 : vm8000 inmail answer table schedule. P...

  • Page 551

    Univerge sv8100 issue 1.0 programming manual 2 - 517 02 override mailbox category (override mb ctg) use this option to specify the category of the mailbox where automated attendant calls should route when you enable answer schedule override. Vm8000 inmail mailbox categories are subscriber mailbox, m...

  • Page 552

    Issue 1.0 univerge sv8100 2 - 518 program 47 : inmail 03 default mailbox category (default mb ctg) use this option to specify the category of mailbox used as the default mailbox. Vm8000 inmail mailbox categories are subscriber mailbox, master mailbox, and routing mailbox. Vm8000 inmail uses the defa...

  • Page 553

    Univerge sv8100 issue 1.0 programming manual 2 - 519 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 554: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 520 program 47 : inmail description use 47-12 : vm8000 inmail answer schedules to set up the vm8000 inmail automated attendant answer schedules. There are eight answer tables, with up to 10 answer schedules in each answer table. Program 47 : inmail 47-12 : vm8000 inmail...

  • Page 555

    Univerge sv8100 issue 1.0 programming manual 2 - 521 01 (continued from previous page) p 3. Date a type 3 answer schedule runs only on a specific day of the year. For this type of schedule, you select: the specific date the schedule should run. On the selected date, the time the schedule should star...

  • Page 556

    Issue 1.0 univerge sv8100 2 - 522 program 47 : inmail 03 day of the week (entryxx day) for day of the week (type 1) answer schedules, use this option to select the day of the week the answer schedule should be active. 1 = sunday 2 = monday 3 = tuesday 4 = wednesday 5 = thursday 6 = friday 7 = saturd...

  • Page 557

    Univerge sv8100 issue 1.0 programming manual 2 - 523 example type 1 (day of the week) answer schedule options type 1 (day of week) example in this example, answer table 1 routes calls as follows: r schedule 1 uses routing mailbox 2 and runs sunday from 8:30am to 5:00pm. R schedule 2 uses subscriber ...

  • Page 558

    Issue 1.0 univerge sv8100 2 - 524 program 47 : inmail type 1 (day of week) example answer table 1 answer schedule 1 answer schedule 1 is a day of week schedule that runs sunday from 8:30am to 5:00pm. 47-12-01: entry01 schedule type = 1 47-12-02: entry01 mb ctg = 3 47-12-02: entry01 mb num = 2 47-12-...

  • Page 559

    Univerge sv8100 issue 1.0 programming manual 2 - 525 type 2 (range of days) answer schedule options type 2 (range of days) example r in this example, answer table 1 routes calls as follows: r schedule 1 uses routing mailbox 1 and runs sunday through wednesday from 8:30am to 5:00pm. R schedule 2 uses...

  • Page 560

    Issue 1.0 univerge sv8100 2 - 526 program 47 : inmail type 2 (range of days) example answer table 1 answer schedule 1 answer schedule 1 is a range of days schedule that starts schedule that runs sunday through wednesday from 8:30am to 5:00pm. 47-12-01: entry01 schedule type = 2 47-12-02: entry01 mb ...

  • Page 561

    Univerge sv8100 issue 1.0 programming manual 2 - 527 type 3 (date) answer schedule options type 3 (date) example in this example, answer table 1 routes calls as follows: r schedule 1 uses routing mailbox 1 and runs every day from 8:30am to 5:00pm. R schedule 2 uses routing mailbox 9 and runs only on...

  • Page 562

    Issue 1.0 univerge sv8100 2 - 528 program 47 : inmail conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 563: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 529 description use 47-13 : vm8000 inmail dial action tables to set up the vm8000 inmail dial action tables. The dial action table defines the options than an automated attendant caller can dial. A dial action table is associated with a call routing m...

  • Page 564

    Issue 1.0 univerge sv8100 2 - 530 program 47 : inmail dial action table actions r trf action - screened transfer (1) (trf) use this action to allow an automated attendant caller to place a screened transfer to an extension. After an automated attendant caller dials an extension, vm8000 inmail calls ...

  • Page 565

    Univerge sv8100 issue 1.0 programming manual 2 - 531 to have unscreened transfer call a specific extension, the corresponding number option should be that extension number. The caller then dials that single digit to reach the extension. For example, to have callers dial 8 to reach extension 303, for...

  • Page 566

    Issue 1.0 univerge sv8100 2 - 532 program 47 : inmail r logon action – log onto voice mail (5) (logon ) use this key action to allow an automated attendant caller to log onto voice mail. Depending on programming (see number option below), the caller is logged directly into a subscriber mailbox or is...

  • Page 567

    Univerge sv8100 issue 1.0 programming manual 2 - 533 r goto action – go to mailbox (7) (goto) use this option to provide automated attendant callers with the ability to route to call routing and announcement mailboxes. For example, a caller can dial a digit for sales, and then go to the call routing...

  • Page 568

    Issue 1.0 univerge sv8100 2 - 534 program 47 : inmail input data dial action table number 01~16 key no. Dial action table action additional data 1 p trf action - screened transfer (1) (trf) p utrf action - unscreened transfer (2) (utrf) p rec1 action - quick message with greeting (3) (rec1) p rec2 a...

  • Page 569

    Univerge sv8100 issue 1.0 programming manual 2 - 535 conditions none defaults feature cross reference none dial action table default settings key dial action table 1 dial action tables 2~16 1 utrf to xxx (unscreened transfer to user-dialed extension) und (undefined) 2 und (undefined) und (undefined)...

  • Page 570: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 536 program 47 : inmail description use 47-15 : routing directory mailbox options to define the routing directory mailbox options. This data is referred if program 47-07-02 (routing master mailbox type) was set to type 4 (directory). Conditions none feature cross refere...

  • Page 571: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 537 description use 47-16 : inmail language license to define the language order inmail uses. Depending on the language license number, inmail uses the languages defined starting from language 1. For example, if the system has a two language license i...

  • Page 572

    Issue 1.0 univerge sv8100 2 - 538 program 47 : inmail conditions none feature cross reference none table 2-14 47-16-01 default table language no. 47-16-01 default language 1 01 (us english) language 2 04 (french canadian) language 3 06 (mexican spanish) language 4 00 (no entry) language 5 00 (no ent...

  • Page 573: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 539 description use 47-17 : routing distribution mailbox options to assign data when program 47-07-02 is set to 4 (distribution). Conditions none feature cross reference none program 47 : inmail 47-17 : routing distribution mailbox options level: in i...

  • Page 574: Program 47 : Inmail

    Issue 1.0 univerge sv8100 2 - 540 program 47 : inmail description use 47-18 vm8000 inmail smtp setup to set the snmp e-mail notification. (not supported in v1000) conditions none feature cross reference none program 47 : inmail 47-18 : vm8000 inmail smtp setup level: in item no. Item input data defa...

  • Page 575: Program 47 : Inmail

    Univerge sv8100 issue 1.0 programming manual 2 - 541 description use 47-19 : vm8000 inmail pop3 setup to set the inmail e-mail notification. (not supported in v1000) conditions none feature cross reference none program 47 : inmail 47-19 : vm8000 inmail pop3 setup level: in item no. Item input data d...

  • Page 576

    Issue 1.0 univerge sv8100 2 - 542 program 47 : inmail this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 577: Signaling Service

    Programming manual 2 - 543 program 50 description use program 50-01 : ccis system setting to set the availability of ccis in the univerge sv8100. No other ccis settings function if this program is disabled. Conditions none feature cross reference none program 50 : common channel interoffice signalin...

  • Page 578

    Issue 1.0 univerge sv8100 2 - 544 program 50 : common channel interoffice signaling service description use program 50-02 : connecting system settings to define the settings for each ccis route id. Program 50 : common channel interoffice signaling service 50-02 : connecting system settings level: in...

  • Page 579

    Univerge sv8100 issue 1.0 programming manual 2 - 545 conditions p if 56k k-ccis is used, 24 multi-frame (esf) must be assigned in program 10-03-02. P dpc must be what the opc is on the opposite side of the link. Feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visi...

  • Page 580

    Issue 1.0 univerge sv8100 2 - 546 program 50 : common channel interoffice signaling service description use program 50-03 : ccis destination system settings to assign information of remote systems in a ccis network. Conditions none feature cross reference none program 50 : common channel interoffice...

  • Page 581

    Univerge sv8100 issue 1.0 programming manual 2 - 547 description use program 50-04 : ccis office code assignment to define the office code when the ccis network is constructed with an open numbering plan. Conditions p this program is used only in an open numbering plan network. This should include t...

  • Page 582

    Issue 1.0 univerge sv8100 2 - 548 program 50 : common channel interoffice signaling service description use program 50-05 : ccis maximum call forwarding hop counter to define the maximum hop counter of call forwarding. Conditions none feature cross reference none program 50 : common channel interoff...

  • Page 583

    Univerge sv8100 issue 1.0 programming manual 2 - 549 description use program 50-06 : ccis feature availability to define the availability of ccis features. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-06 : ccis feature availability level: ...

  • Page 584

    Issue 1.0 univerge sv8100 2 - 550 program 50 : common channel interoffice signaling service description use program 50-07 : ccis centralized billing center office to define the point code and ccis route id for the billing center office. Conditions none feature cross reference none program 50 : commo...

  • Page 585

    Univerge sv8100 issue 1.0 programming manual 2 - 551 description use program 50-08 : ccis centralized blf sending group assignment to define the destination of blf for the sending system. Eight sending systems can be registered in this program. Conditions none feature cross reference none program 50...

  • Page 586

    Issue 1.0 univerge sv8100 2 - 552 program 50 : common channel interoffice signaling service description use program 50-09 : ccis centralized blf sending extension number assignment to define the extension number for sending blf messages. One extension number can have a sending switch for each sendin...

  • Page 587

    Univerge sv8100 issue 1.0 programming manual 2 - 553 conditions none feature cross reference none 07 send to sending group 6 0 = disable 1 = enable 0 enable (0) or disable (1) the ability to send the blf to send group 6 assigned in prg 50-08-xx. 08 send to sending group 7 0 = disable 1 = enable 0 en...

  • Page 588

    Issue 1.0 univerge sv8100 2 - 554 program 50 : common channel interoffice signaling service description use program 50-10 : ccis centralized blf interval time assignment to define the time to send blf messages. Conditions none feature cross reference none program 50 : common channel interoffice sign...

  • Page 589

    Univerge sv8100 issue 1.0 programming manual 2 - 555 description use program 50-11 : ccis centralized day/night switching sending group assignment to define point code and ccis route id for sending day/night switching message. Conditions none feature cross reference none program 50 : common channel ...

  • Page 590

    Issue 1.0 univerge sv8100 2 - 556 program 50 : common channel interoffice signaling service description use program 50-12 : ccis centralized day/night mode to system mode assignment to define corresponding night mode to switch to when day/night mode switching message arrives. Conditions none feature...

  • Page 591

    Univerge sv8100 issue 1.0 programming manual 2 - 557 description use program 50-13 : ccis centralized response timeout assignment to define the response timeout value. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-13 : ccis centralized resp...

  • Page 592

    Issue 1.0 univerge sv8100 2 - 558 program 50 : common channel interoffice signaling service description use program 50-14 : ccis intercom digits for caller id call return to eliminate the 9 on caller id redial except for 7- and 8-digit extensions. Conditions none feature cross reference none program...

  • Page 593

    Univerge sv8100 issue 1.0 programming manual 2 - 559 description use program 50-15 : ccis over ip basic information setting to set the basic parameters for ccis over ip. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-15 : ccis over ip basic ...

  • Page 594

    Issue 1.0 univerge sv8100 2 - 560 program 50 : common channel interoffice signaling service this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 595

    Programming manual 2 - 561 program 51 description use program 51-01 : netlink system property setting to define the parameters of the netlink feature. Each system must be set with its own information. When the netlink system id is changed (item 01), the system must be reset. Program 51 : netlink ser...

  • Page 596

    Issue 1.0 univerge sv8100 2 - 562 program 51 : netlink service conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 597

    Univerge sv8100 issue 1.0 programming manual 2 - 563 description use program 51-02 : netlink system individual setting to set system data for each netlink system. Program 51-02-03 is not used in us, but is used in other countries. Program 51 : netlink service 51-02 : netlink system individual settin...

  • Page 598

    Issue 1.0 univerge sv8100 2 - 564 program 51 : netlink service conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 599

    Univerge sv8100 issue 1.0 programming manual 2 - 565 description use program 51-03 : netlink internet protocol address list setting to set the ip address of the netlink system. Conditions p the system seeks primary system based on this list. P when there is no primary system yet, or fail over occurs...

  • Page 600

    Issue 1.0 univerge sv8100 2 - 566 program 51 : netlink service this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 601

    Univerge sv8100 issue 1.0 programming manual 2 - 567 description use program 51-04 : ip address setting of top priority primary system of netlink to set the ip address of the new primary system. Conditions none feature cross reference none program 51 : netlink service 51-04 : ip address setting of t...

  • Page 602

    Issue 1.0 univerge sv8100 2 - 568 program 51 : netlink service description use program 51-05 : netlink timer settings to set the various timers within the netlink system. Program 51 : netlink service 51-05 : netlink timer settings level: in item no. Item input data default 01 keep alive sending inte...

  • Page 603

    Univerge sv8100 issue 1.0 programming manual 2 - 569 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 604

    Issue 1.0 univerge sv8100 2 - 570 program 51 : netlink service description use program 51-06 : netlink primary automatic integration settings to set the automatic integration of the primary system. Conditions none feature cross reference none program 51 : netlink service 51-06 : netlink primary auto...

  • Page 605

    Univerge sv8100 issue 1.0 programming manual 2 - 571 description use program 51-07 : netlink primary compulsion specification setting to set compulsion specification of the primary system. Conditions none feature cross reference none program 51 : netlink service 51-07 : netlink primary compulsion sp...

  • Page 606

    Issue 1.0 univerge sv8100 2 - 572 program 51 : netlink service description use program 51-08 : primary netlink setting to set the ip address and system id of the compulsory specification of the primary system. (this program is available only via telephone programming and not through pc programming)....

  • Page 607

    Univerge sv8100 issue 1.0 programming manual 2 - 573 description use program 51-09 : netlink communication port settings to set the various communication ports used on the system. Program 51 : netlink service 51-09 : netlink communication port settings level: in input data item no. Item input data d...

  • Page 608

    Issue 1.0 univerge sv8100 2 - 574 program 51 : netlink service conditions none feature cross reference none 07 database replication primary detection port this port is used to replicate database. If 0 is specified, temporary port is selected by dynamic. 0~65535 0 input data item no. Item input data ...

  • Page 609

    Univerge sv8100 issue 1.0 programming manual 2 - 575 description use program 51-10: virtual slot setting to view the number of virtual slots that are remaining in a netlink network. There can be up to 240 virtual slots available in netlink. Conditions p this program is “read only.” feature cross ref...

  • Page 610

    Issue 1.0 univerge sv8100 2 - 576 program 51 : netlink service description use program 51-11: netlink system information to reference information about other systems in the netlink network. Conditions p this program is “read only.” feature cross reference none program 51 : netlink service 51-11 : ne...

  • Page 611

    Univerge sv8100 issue 1.0 programming manual 2 - 577 description use program 51-12: primary system information to reference information about the primary system in the netlink network. Conditions p this program is “read only.” feature cross reference none program 51 : netlink service 51-12 : primary...

  • Page 612: 51-13 : Netlink Options

    Issue 1.0 univerge sv8100 2 - 578 program 51 : netlink service description use program 51-13: netlink options to enable automatic ip address list operation updates, time zone information, and mac address authorization. Conditions none feature cross reference none program 51 : netlink service 51-13 :...

  • Page 613

    Univerge sv8100 issue 1.0 programming manual 2 - 579 description use program 51-14: netlink system control to delete system and slot information. (this program is available only via telephone programming and not through pc programming). Conditions none feature cross reference none program 51 : netli...

  • Page 614

    Issue 1.0 univerge sv8100 2 - 580 program 51 : netlink service description use program 51-15: demonstration setting to automatically set the minimum setting values in netlink. A system reset occurs after this command is executed. (this program is available only via telephone programming and not thro...

  • Page 615

    Univerge sv8100 issue 1.0 programming manual 2 - 581 description use program 51-16: netlink system data replication mode setting to set the system data replication between the primary and secondary systems. Program 51 : netlink service 51-16 : netlink system data replication mode setting level: in i...

  • Page 616

    Issue 1.0 univerge sv8100 2 - 582 program 51 : netlink service conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 617

    Programming manual 2 - 583 program 80 description use program 80-01 : service tone setup to define up to 64 service tones. Each service tone is defined by the combination of 32 basic tones. Program 80 : basic hardware setup for system 80-01 : service tone setup level: in input data service tone numb...

  • Page 618

    Issue 1.0 univerge sv8100 2 - 584 program 80 : basic hardware setup for system default table 2-15 basic tones basic tone no. Frequency (hz) level (db) basic tone no. Frequency (hz) level (db) 01 400 - 13 17 520 / 650 -13 / -19 02 520 -13 18 650 / 780 -13 / -19 03 580 -13 19 780 / 1040 -13 / -19 04 6...

  • Page 619

    Univerge sv8100 issue 1.0 programming manual 2 - 585 6 internal busy tone 0 basic 2 0 11 5 5 20 (-6db) 20 (-6db) 7 dnd busy tone 0 basic 2 0 1 2 2 32 (0db) 32 (0db) 8 b-busy tone 0 basic 2 0 11 5 5 20 (-6db) 20 (-6db) 9 internal reorder tone 0 basic 2 11 0 3 2 20 (-6db) 20 (-6db) 10 internal interru...

  • Page 620

    Issue 1.0 univerge sv8100 2 - 586 program 80 : basic hardware setup for system 22 door box chime 4 3 basic 6 4 4 2 2 2 0 1 1 2 2 3 2 38 (+3db) 26 (-3db) 38 (+3db) 26 (-3db) 14 (-9db) 32 (0db) 23 door box chime 5 3 basic 6 7 7 5 5 5 0 1 1 2 2 3 2 38 (+3db) 26 (-3db) 38 (+3db) 26 (-3db) 14 (-9db) 32 (...

  • Page 621

    Univerge sv8100 issue 1.0 programming manual 2 - 587 37 external reorder tone 0 basic 2 7 0 5 5 32 (0db) 32 (0db) 38 external busy tone 0 basic 2 7 0 7 7 32 (0db) 32 (0db) 39 special audible ring busy tone 0 basic 6 0 11 0 11 10 0 5 5 5 5 10 20 32 (0db) 32 (0db) 32 (0db) 32 (0db) 32 (0db) 32 (0db) 4...

  • Page 622

    Issue 1.0 univerge sv8100 2 - 588 program 80 : basic hardware setup for system conditions p the system must be reset for any changes to these items to take affect. Feature cross reference r selectable ring tones 58 opening chime tone 1 basic 8 2 2 14 14 15 15 16 16 2 2 2 2 2 2 6 4 32 (0db) 26 (-3db)...

  • Page 623: 80-02 : Dtmf Tone Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 589 description use program 80-02 : dtmf tone setup to define the duration (on time) and pause (off time) for dtmf dialing. This option affects all trunk line calls system wide. Make separate entries for duration and pause. It is also possible to adju...

  • Page 624

    Issue 1.0 univerge sv8100 2 - 590 program 80 : basic hardware setup for system conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 625

    Univerge sv8100 issue 1.0 programming manual 2 - 591 description use program 80-03 : dtmf tone receiver setup to define the various levels and timers for the dtmf tone receiver. Dtmf tone receiver type: r 1 = dtmf receiver for extension r 2 = dtmf receiver for analog trunk r 3 = dtmf receiver for di...

  • Page 626

    Issue 1.0 univerge sv8100 2 - 592 program 80 : basic hardware setup for system default conditions none feature cross reference none 04 max. Detect level 0~15 dtmf tone 1 : -5dbm(0) to -20dbm(15) dtmf tone 2 : -10dbm(0) to -25dbm(15) dtmf tone 3 : -15dbm(0) to -30dbm(15) dtmf tone 4 : -20dbm(0) to -3...

  • Page 627

    Univerge sv8100 issue 1.0 programming manual 2 - 593 description use program 80-04 : call progress tone detector setup to define the various levels and timers for the call progress tone detector. Tone detector type: r 1 = dial tone for trunk r 2 = busy tone for trunk r 3 = ring back tone for trunk r...

  • Page 628

    Issue 1.0 univerge sv8100 2 - 594 program 80 : basic hardware setup for system default conditions none feature cross reference none 04 no tone time 0~255 (30+30~7680ms) (0 =not detect) 1~255 = 60~7680ms. The formula is 30+30n. When set to n=1, it means 30+30*1=60 when set to n=255, it means 30+30*25...

  • Page 629

    Univerge sv8100 issue 1.0 programming manual 2 - 595 description use program 80-05 : date format for smdr and system to define the date format when printing out the smdr, alarm report, and system information report. Conditions none feature cross reference none program 80 : basic hardware setup for s...

  • Page 630

    Issue 1.0 univerge sv8100 2 - 596 program 80 : basic hardware setup for system description use program 80-07 : call progress tone detector frequency setup to set the frequency of the detection tone set with program 80-04-12 and program 80-04-13. Conditions none feature cross reference none program 8...

  • Page 631: 80-09 : Short Ring Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 597 description use program 80-09 : short ring setup to define the short ring tone for sv8100 multiline terminals. When a single tone is sent, frequency 1/2 is set to the same value. Program 80 : basic hardware setup for system 80-09 : short ring setu...

  • Page 632

    Issue 1.0 univerge sv8100 2 - 598 program 80 : basic hardware setup for system 12 1175 13 1318 14 1397 15 1568 table 2-17 ring cycle table data ring cycle (ms) 01 125(on)/off 02 125(on)/125(off)/125(on)/off 03 125(on)/125(off)/125(on)/125(off)/125(on)/off 04 125(on)/125(off)/125(on)/125(off)/125(on)...

  • Page 633

    Univerge sv8100 issue 1.0 programming manual 2 - 599 conditions none feature cross reference none table 2-18 default table short ring no. Short tone name frequency 1 frequency 2 ring cycle 1 confirmation tone 8 8 1 2 error tone 8 8 14 3 alarm tone for long conversation call 4 4 14 4 not defined 0 0 ...

  • Page 634

    Issue 1.0 univerge sv8100 2 - 600 program 80 : basic hardware setup for system description use program 80-10 : mf tone receiver setup to various data for the mf signal detection. Program 80 : basic hardware setup for system 80-10 : mf tone receiver setup level: mf input data mf tone receiver type nu...

  • Page 635

    Univerge sv8100 issue 1.0 programming manual 2 - 601 input data item no. Item input data 01 detect level 0 = 0dbm ~ -25dbm 1 = -5dbm ~ -30dbm 2 = -10dbm ~ -35dbm 3 = -15dbm ~ -40dbm 4 = -20dbm ~ -45dbm 5 = -25dbm ~ -50dbm 6 = -30dbm ~ -55dbm 02 start delay time 0~255 (0.25step, 0ms~64ms) 03 min. Det...

  • Page 636

    Issue 1.0 univerge sv8100 2 - 602 program 80 : basic hardware setup for system conditions none feature cross reference none table 2-19 default table item name type 1 type 2 type 3 type 4 type 5 01 detect level 0 0 0 0 0 02 start delay time 0 0 0 0 0 03 min. Detect level 10 (-20dbm) 10 (-20dbm) 10 (-...

  • Page 637

    Programming manual 2 - 603 program 81 description use program 81-01 : cot initial data setup to define the various basic data parameters for the cot unit. Program 81 : basic hardware setup for trunk 81-01 : cot initial data setup level: mf input data item no. Item input data default 01 pcm encoding ...

  • Page 638

    Issue 1.0 univerge sv8100 2 - 604 program 81 : basic hardware setup for trunk 13 grounding time 1~255 (16~4080ms) 9 (144ms) 14 hook flash 1 time 1~255 (16~4080ms) 50 (800ms) 15 hook flash 2 time 1~255 (16~4080ms) 156 (2496ms) 16 pause time 1~255 (64~16320ms) 16 (1024ms) 17 pft idle detection time 1~...

  • Page 639

    Univerge sv8100 issue 1.0 programming manual 2 - 605 conditions none feature cross reference none 32 dp inter-digit time (20pps) 1~255 (32~8160ms) 16 (512ms) 33 --- not used --- 34 --- not used --- 35 --- not used --- 36 long ringing detection minimum time 1~255 (16~4080ms) 150 (2400ms) input data i...

  • Page 640

    Issue 1.0 univerge sv8100 2 - 606 program 81 : basic hardware setup for trunk description use program 81-02 : diopu initial data setup to define the various basic timers for the did unit. Program 81 : basic hardware setup for trunk 81-02 : diopu initial data setup level: mf input data item name inpu...

  • Page 641

    Univerge sv8100 issue 1.0 programming manual 2 - 607 conditions none feature cross reference none 14 receive dp break minimum time 1~255 (2~510ms) 5 (10ms) 15 receive dp break maximum time 1~255 (2~510ms) 50 (100ms) 16 receive dp inter-digit time 1~255 (32~8160ms) 6 (192ms) 17 loop off guard time 0~...

  • Page 642

    Issue 1.0 univerge sv8100 2 - 608 program 81 : basic hardware setup for trunk description use program 81-03 : odt initial data setup to define the various basic timers for the e&m tie line unit. Program 81 : basic hardware setup for trunk 81-03 : odt initial data setup level: in input data item name...

  • Page 643

    Univerge sv8100 issue 1.0 programming manual 2 - 609 conditions none feature cross reference none 14 receive dp make maximum time 1~255 (2~510ms) 50 (100ms) 15 receive dp break minimum time 1~255 (2~510ms) 5 (10ms) 16 receive dp break maximum time 1~255 (2~510ms) 50 (100ms) 17 pause time after wink/...

  • Page 644

    Issue 1.0 univerge sv8100 2 - 610 program 81 : basic hardware setup for trunk description use program 81-04 : isdn bri layer 1 (t-point) initial data setup to define the various basic data for layer 1 of isdn bri. Conditions none feature cross reference none program 81 : basic hardware setup for tru...

  • Page 645

    Univerge sv8100 issue 1.0 programming manual 2 - 611 description use program 81-05 : isdn bri & pri layer 2 (t-point) initial data setup to define the various basic data for layer 2 of isdn bri and pri. Program 81 : basic hardware setup for trunk 81-05 : isdn bri & pri layer 2 (t-point) initial data...

  • Page 646

    Issue 1.0 univerge sv8100 2 - 612 program 81 : basic hardware setup for trunk conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 647

    Univerge sv8100 issue 1.0 programming manual 2 - 613 description use program 81-06 : isdn bri & pri layer 3 (t-point) timer setup to define the various basic timers for layer 3 of isdn bri/pri (defined in program 10-03-04). Program 81 : basic hardware setup for trunk 81-06 : isdn bri & pri layer 3 (...

  • Page 648

    Issue 1.0 univerge sv8100 2 - 614 program 81 : basic hardware setup for trunk 08 t308 specifies the timer value in 1/100ths of a second of the timer to be started when rel is sent. 1~254 (sec) 4 (sec) 09 t309 specifies the timer value in 1/100ths of a second upon data link disconnection. 1-254 (sec)...

  • Page 649

    Univerge sv8100 issue 1.0 programming manual 2 - 615 conditions none feature cross reference r isdn compatibility digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 650

    Issue 1.0 univerge sv8100 2 - 616 program 81 : basic hardware setup for trunk description use program 81-07 : codec filter setup for analog trunk port to define the codec (qslac) filter for each analog trunk port. Conditions none feature cross reference none program 81 : basic hardware setup for tru...

  • Page 651

    Univerge sv8100 issue 1.0 programming manual 2 - 617 description use program 81-08 : t1 trunk timer setup to define the basic timer setting of each t1 trunk type. Program 81 : basic hardware setup for trunk 81-08 : t1 trunk timer setup level: in item name input data default 01 answer signal detectio...

  • Page 652

    Issue 1.0 univerge sv8100 2 - 618 program 81 : basic hardware setup for trunk 14 ringing signal detection time (e&m) 1~250 (8ms ~ 2000ms) 10 80ms 15 ringing signal detection time (opx) 1~250 (8ms ~ 2000ms) 10 80ms 16 ringing signal stop detection time (loop) 1~255 (100ms ~ 25500ms) 50 5000ms 17 ring...

  • Page 653

    Univerge sv8100 issue 1.0 programming manual 2 - 619 33 hookflash send time (opx) 1~255 (100ms ~ 25500ms ) 5 500ms 34 pause send time (all) 1~255 (1sec ~ 255sec ) 3 3sec 35 wink send duration time (did) 1~250 (8ms ~ 2000ms) 25 200ms 36 delay send duration time (did) 1~250 (8ms ~ 2000ms) 25 200ms 37 ...

  • Page 654

    Issue 1.0 univerge sv8100 2 - 620 program 81 : basic hardware setup for trunk 52 receive hookflash duration min. Time (e&m) 1~255 (100ms ~ 25500ms) 3 300ms 53 receive hookflash duration max. Time (e&m) 1~255 (100ms ~ 25500ms) 6 600ms 54 receive hookflash duration min. Time (opx) 1~255 (100ms ~ 25500...

  • Page 655

    Univerge sv8100 issue 1.0 programming manual 2 - 621 conditions none feature cross reference none 71 guard time 1 (ground) 1~255 (100ms ~ 25500ms) 9 900ms 72 guard time 1 (did) 1~250 (4ms ~ 1000ms) 3 12ms 73 guard time 1 (e&m) 1~255 (100ms ~ 25500ms) 20 2000ms 74 guard time 1 (opx) 1~255 (100ms ~ 25...

  • Page 656

    Issue 1.0 univerge sv8100 2 - 622 program 81 : basic hardware setup for trunk description use program 81-09 : cot codec (qslac) filter setting to define the filter setting data (when program 81-07 is set to 4). Program 81 : basic hardware setup for trunk 81-09 : cot codec (qslac) filter setting leve...

  • Page 657

    Univerge sv8100 issue 1.0 programming manual 2 - 623 conditions p this is used if program 81-07 is set to 4 (specified data). Feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 658

    Issue 1.0 univerge sv8100 2 - 624 program 81 : basic hardware setup for trunk description use program 81-10 : cot initial data setup to define the various basic timers for each cot trunk port. Program 81 : basic hardware setup for trunk 81-10 : cot initial data setup level: in input data trunk no. 1...

  • Page 659

    Univerge sv8100 issue 1.0 programming manual 2 - 625 conditions none feature cross reference none 07 hookflash time selection 1 normal hook flash 0 = 20ms 1 = 40ms 2 = 60ms 3 = 80ms 4 = 100ms 5 = 140ms 6 = 160ms 7 = 200ms 8 = 400ms 9 = 600ms 10 = 800ms 11 = 1.0 seconds 12 = 1.5 seconds 13 = 2.0 seco...

  • Page 660

    Issue 1.0 univerge sv8100 2 - 626 program 81 : basic hardware setup for trunk description use program 81-11 : tie line initial setup to define the various initial data for did/ tli/dti packages. Program 81 : basic hardware setup for trunk 81-11 : tie line initial setup level: in input data trunk no....

  • Page 661

    Univerge sv8100 issue 1.0 programming manual 2 - 627 05 incoming signal detect time selection specifies the time after the incoming signal from another system is detected before the acknowledge signal is sent out. [wink start] 1~15 (130ms~1950ms) (0 = no setting) [delay] 1~15 (30ms~450ms) (0 = no se...

  • Page 662

    Issue 1.0 univerge sv8100 2 - 628 program 81 : basic hardware setup for trunk conditions none feature cross reference none 14 hookflash time selection 1 0 = 20ms 1 = 40ms 2 = 60ms 3 = 80ms 4 = 100ms 5 = 140ms 6 = 160ms 7 = 200ms 8 = 400ms 9 = 600ms 10 = 800ms 11 = 1.0 seconds 12 = 1.5 seconds 13 = 2...

  • Page 663

    Univerge sv8100 issue 1.0 programming manual 2 - 629 description use program 81-12 : trunk pad level data setup to define the various initial data for tli/dti/did/brt/prt package. Conditions none feature cross reference none program 81 : basic hardware setup for trunk 81-12 : trunk pad level data se...

  • Page 664

    Issue 1.0 univerge sv8100 2 - 630 program 81 : basic hardware setup for trunk this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 665

    Programming manual 2 - 631 program 82 description use program 82-01 : incoming ring tone to set the incoming ring tones, which are the tones a user hears when a call rings an extension. These tones are grouped into four ring tone ranges (1~4), also called patterns, that consist of a combination of f...

  • Page 666

    Issue 1.0 univerge sv8100 2 - 632 program 82 : basic hardware setup for extension conditions none feature cross reference r distinctive ringing tones and flash patterns r selectable ring tones 03 modulation 0 = no modulation 1 = 8hz modulation 2 = 16hz modulation 3 = envelope default incoming ringin...

  • Page 667

    Univerge sv8100 issue 1.0 programming manual 2 - 633 description use program 82-03 : dss console led pattern setup to define the led patterns for special functions on a dss console. Led pattern 0 : [off] led pattern 1 : [fl: on(500ms)/off(500ms)] led pattern 2 : [wk: on(250ms)/off(250ms)] led patter...

  • Page 668

    Issue 1.0 univerge sv8100 2 - 634 program 82 : basic hardware setup for extension led pattern 4 : [ir: on(125ms)/off(125ms)/on(125ms)/off(625ms)] led pattern 5 : [il: on(875ms)/off(125ms)] led pattern 6 : [iw: on(625ms)/off(125ms)/on(125ms)/off(125ms)] led pattern 7 : [on] conditions none feature cr...

  • Page 669

    Univerge sv8100 issue 1.0 programming manual 2 - 635 description use program 82-04 : lca initial data setup to set the basic data of the lca. Program 82 : basic hardware setup for extension 82-04 : lca initial data setup level: mf input data item no. Item input data default 01 companding method type...

  • Page 670

    Issue 1.0 univerge sv8100 2 - 636 program 82 : basic hardware setup for extension conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 671

    Univerge sv8100 issue 1.0 programming manual 2 - 637 description use program 82-07 : codec filter setup for analog station port to set the filter value of the codec (qslac) filter of each analog port. Conditions none feature cross reference r direct station selection (dss) program 82 : basic hardwar...

  • Page 672

    Issue 1.0 univerge sv8100 2 - 638 program 82 : basic hardware setup for extension description use program 82-08 : sidetone volume setup for adjusting the telephone sidetone volume. There are two levels, based on whether the connected trunk is a digital trunk or analog trunk. Conditions none feature ...

  • Page 673

    Univerge sv8100 issue 1.0 programming manual 2 - 639 description use program 82-09 : lca codec filter data setup to define the filter setting data (when program 82-07 is set to 4). Program 82 : basic hardware setup for extension 82-09 : lca codec filter data setup level: in input data item name inpu...

  • Page 674

    Issue 1.0 univerge sv8100 2 - 640 program 82 : basic hardware setup for extension conditions p this is used if program 82-07 is set to 4 (specified data). Feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 675

    Univerge sv8100 issue 1.0 programming manual 2 - 641 description use program 82-11 : lca initial data setup to define the various timers for lca packages. Conditions none feature cross reference none program 82 : basic hardware setup for extension 82-11 : lca initial data setup level: in input data ...

  • Page 676

    Issue 1.0 univerge sv8100 2 - 642 program 82 : basic hardware setup for extension description use program 82-12 : opx initial data setup to define the various initial data for opx packages. Conditions none feature cross reference none program 82 : basic hardware setup for extension 82-12 : opx initi...

  • Page 677

    Programming manual 2 - 643 program 84 description use program 84-01 : h.323 trunk basic information setup to set the basic information of the h.323 trunk. Program 84 : hardware setup for voip 84-01 : h.323 trunk basic information setup level: in input data item no. Item input data default 02 number ...

  • Page 678

    Issue 1.0 univerge sv8100 2 - 644 program 84 : hardware setup for voip 15 jitter buffer mode 1 = fixed 2 = self adjusting (silence period) 3 = self adjusting 3 16 g.711 jitter buffer( min) 0~160 30 17 g.711 jitter buffer (average) 0~160 60 18 g.711 jitter buffer (max) 0~160 120 19 g.723 jitter buffe...

  • Page 679

    Univerge sv8100 issue 1.0 programming manual 2 - 645 34 --- not used --- 35 --- not used --- 36 the maximum fax transmission rate 0 = v.27ter, 2400bps 1 = v.27ter, 4800bps 2 = v.29, 7200bps 3 = v.29, 9600bps 4 = v.17, 12000bps 5 = v.17, 14400bps 5 37 fax fifo considering delay time 0~600ms 300 38 si...

  • Page 680

    Issue 1.0 univerge sv8100 2 - 646 program 84 : hardware setup for voip conditions none feature cross reference 52 eflag setting at head dis (fax relay item) 0 = disable 1 = enable 1 53 tfop protocol (fax relay item) 1 54 nsf superscription (fax relay item) 0 55 ecm (error correction mode) 1 56 enabl...

  • Page 681

    Univerge sv8100 issue 1.0 programming manual 2 - 647 description use program 84-02 : h.225 and h.245 information basic setup to define the basic setup information of h.225 and h.245. Program 84 : hardware setup for voip 84-02 : h.225 and h.245 information basic setup level: in input data item no. It...

  • Page 682

    Issue 1.0 univerge sv8100 2 - 648 program 84 : hardware setup for voip conditions none feature cross reference r voice over internet protocol (voip) 22 arq retry count 0~255 2 23 ras brq timer 0~255sec 5 24 brq retry count 0~255 2 25 ras irr timer 0~255sec 5 26 irr retry count 0~255 2 27 ras drq tim...

  • Page 683

    Univerge sv8100 issue 1.0 programming manual 2 - 649 description use program 84-03 : ip phone information basic setup to define the details of ip terminals and adapters. Program 84 : hardware setup for voip 84-03 : ip phone information basic setup level: in input data terminal type 1 = d term ip / u...

  • Page 684

    Issue 1.0 univerge sv8100 2 - 650 program 84 : hardware setup for voip conditions none feature cross reference voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 685: 84-06 : Pva Data Setting

    Univerge sv8100 issue 1.0 programming manual 2 - 651 description use program 84-06 : pva data setting to set up threshold levels of every cd-pvaa slot. (this program is not available with v1000) (this program is available only via telephone programming and not through pc programming). Program 84 : h...

  • Page 686

    Issue 1.0 univerge sv8100 2 - 652 program 84 : hardware setup for voip conditions p system programming must be exited before these program options take affect. Feature cross reference r voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitc...

  • Page 687

    Univerge sv8100 issue 1.0 programming manual 2 - 653 description use program 84-07 : firmware download setup to configure the settings related to central firmware download for ip phones. Conditions none feature cross reference none program 84 : hardware setup for voip 84-07 : firmware download setup...

  • Page 688

    Issue 1.0 univerge sv8100 2 - 654 program 84 : hardware setup for voip description use program 84-08 : firmware name setup to set up the directory and filename for the firmware that is downloaded to ip phones. Conditions none feature cross reference none program 84 : hardware setup for voip 84-08 : ...

  • Page 689: 84-09 : Vlan Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 655 description use program 84-09 : vlan setup to set up the vlan data. Conditions p system programming must be exited before these program options take affect. Feature cross reference r voice over internet protocol (voip) program 84 : hardware setup ...

  • Page 690: 84-10 : Tos Setup

    Issue 1.0 univerge sv8100 2 - 656 program 84 : hardware setup for voip description use program 84-10 : tos setup to set up the type of service data. Program 84 : hardware setup for voip 84-10 : tos setup level: in input data protocol type 1 = not used 2 = not used 3 = voice control 4 = h.323 5 = rtp...

  • Page 691

    Univerge sv8100 issue 1.0 programming manual 2 - 657 conditions p the system must be reset for these program options to take affect. Feature cross reference r voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 692: 84-11 :

    Issue 1.0 univerge sv8100 2 - 658 program 84 : hardware setup for voip description use program 84-11 : d term ip codec information basic setup to set voice (rtp packet) encoding parameters. Program 84 : hardware setup for voip 84-11 : d term ® ip codec information basic setup level: in input data ty...

  • Page 693

    Univerge sv8100 issue 1.0 programming manual 2 - 659 conditions none feature cross reference r voice over internet protocol (voip) 18 vad threshold 0~30 = -19db~+10db 0 = adaptec threshold 1 = -19db(-49dbm) : 20 = 0db (-30dbm) : 29 = 9dbm(-21dbm) 30 = 10dbm(-20dbm) 20 26 tx gain 0~40 (-20dbm~ +20dbm...

  • Page 694

    Issue 1.0 univerge sv8100 2 - 660 program 84 : hardware setup for voip this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 695

    Univerge sv8100 issue 1.0 programming manual 2 - 661 description use program 84-13 : sip trunk codec information basic setup to set up the basic codec options for sip trunks. Program 84 : hardware setup for voip 84-13 : sip trunk codec information basic setup level: in input data item no. Item input...

  • Page 696

    Issue 1.0 univerge sv8100 2 - 662 program 84 : hardware setup for voip 18 vad threshold 0~30 (-19db~+10db) 0 = self adjustment 1 = -19db (-49dbm) : 2 = 0db (-30dbm) : 29 = 9dbm (-21dbm) 30 = 10dbm (-20dbm) 20 26 tx gain 0~40 (-20dbm ~ +20dbm) 0 = -20dbm 1 = -19 dbm : 20 = 0dbm : 39 = 19dbm 40 = 20db...

  • Page 697

    Univerge sv8100 issue 1.0 programming manual 2 - 663 conditions none feature cross reference none 36 g.722 jitter buffer (average) 0~160ms 60 37 g.722 jitter buffer (max) 0~160ms 120 38 number of g.726 audio frames 1~4 (1 = 10ms, 4 = 40ms) 3 39 g.726 vad mode 0 = disable 1 = enable 0 40 g.726 jitter...

  • Page 698

    Issue 1.0 univerge sv8100 2 - 664 program 84 : hardware setup for voip description use program 84-14 : sip trunk basic information setup to define the basic setup for sip trunks. Program 84 : hardware setup for voip 84-14 : sip trunk basic information setup level: in input data item no. Item input d...

  • Page 699

    Univerge sv8100 issue 1.0 programming manual 2 - 665 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 700

    Issue 1.0 univerge sv8100 2 - 666 program 84 : hardware setup for voip description use program 84-15 : h.323/sip phone keep alive setup to set the keep alive configuration of the h.323/sip phone. Conditions none feature cross reference none program 84 : hardware setup for voip 84-15 : h.323/sip phon...

  • Page 701

    Univerge sv8100 issue 1.0 programming manual 2 - 667 description use program 84-16 : voip limiter control gain to set the limiter control gain configuration of voip. Conditions none feature cross reference r voice over internet protocol (voip) program 84 : hardware setup for voip 84-16 : voip limite...

  • Page 702

    Issue 1.0 univerge sv8100 2 - 668 program 84 : hardware setup for voip description use program 84-17 : ipl echo canceller control setup to configure echo cancellation. Conditions none feature cross reference none program 84 : hardware setup for voip 84-17 : ipl echo canceller control setup (in level...

  • Page 703

    Univerge sv8100 issue 1.0 programming manual 2 - 669 description use program 84-19 : sip extension codec information basic setup to define the codec information for the sip extensions. Program 84 : hardware setup for voip 84-19 : sip extension codec information basic setup level: in input data item ...

  • Page 704

    Issue 1.0 univerge sv8100 2 - 670 program 84 : hardware setup for voip 17 jitter buffer mode 1 = static 2 = adaptive during silence 3 = adaptive immediately 3 18 vad threshold 0~30 20 26 tx gain 0~30 (-19db ~ +10db, auto) 0 = auto adjust 1 = -19db (-49dbm) : 20 = 0db (-30dbm) : 29 = +9db (-21dbm) 30...

  • Page 705

    Univerge sv8100 issue 1.0 programming manual 2 - 671 conditions p these commands are for sip analog extensions. Feature cross reference none 36 g.722 jitter buffer (average) 0~160ms 60 37 g.722 jitter buffer (max) 0~160ms 120 38 number of g.726 audio frames 1~4 (1 = 10ms, 4 = 40ms) 3 39 g.726 voice ...

  • Page 706

    Issue 1.0 univerge sv8100 2 - 672 program 84 : hardware setup for voip description use program 84-20 : sip extension basic information setup to set up proxy information, session timers, called party information and expire value of invite. Conditions p these commands are for sip analog extensions. Fe...

  • Page 707

    Univerge sv8100 issue 1.0 programming manual 2 - 673 description use program 84-21 : ccis over ip codec information basic setup to set the codec parameters of the pz-32ipla, pz-64ipla, and pz-128ipla. Program 84 : hardware setup for voip 84-21 : ccis over ip codec information basic setup level: in i...

  • Page 708

    Issue 1.0 univerge sv8100 2 - 674 program 84 : hardware setup for voip 12 g.723 audio frame number 1 = 30ms 2 = 60ms 1 13 g.723 voice activity detection mode 0 = disable 1 = enable 0 14 g723 jitter buffer min 0~270ms 30 15 g723 jitter buffer average 0~270ms 60 16 g.723 jitter buffer max 0~270ms 120 ...

  • Page 709

    Univerge sv8100 issue 1.0 programming manual 2 - 675 23 voice activity detection threshold 0 = self adjustment 1 = -19dbm (-49dbm) : 20 = 0dbm (-30dbm) : 29 = +9dbm (-21dbm) 30 = +10dbm (-20dbm) 20 24 echo canceller mode 0 = disable 1 = enable 1 25 nlp echo canceller mode 0 = disable 1 = enable 1 26...

  • Page 710

    Issue 1.0 univerge sv8100 2 - 676 program 84 : hardware setup for voip conditions none feature cross reference r voice over internet protocol (voip) 40 --- not used --- 41 --- not used --- 42 fax relay mode 0 = disable 1 = enable 2 = each port mode (each extension) 0 input data item no. Item input d...

  • Page 711

    Univerge sv8100 issue 1.0 programming manual 2 - 677 description use program 84-22 : dt700 multiline logon information setup to set the dt700 multiline logon information. Conditions none feature cross reference r voice over internet protocol (voip) program 84 : hardware setup for voip 84-22 : dt700 ...

  • Page 712

    Issue 1.0 univerge sv8100 2 - 678 program 84 : hardware setup for voip description use program 84-23 : dt700 multiline basic information setup to set the basic information for the dt700 multiline terminal. Program 84 : hardware setup for voip 84-23 : dt700 multiline basic information setup level: in...

  • Page 713

    Univerge sv8100 issue 1.0 programming manual 2 - 679 conditions none feature cross reference r voice over internet protocol (voip) 08 digest authorization registration expire timer 0~4294967295 (sec) 0 10 number of password retries input the number of times an incorrect password can be entered when ...

  • Page 714

    Issue 1.0 univerge sv8100 2 - 680 program 84 : hardware setup for voip description use program 84-24 : dt700 multiline codec basic information setup to set the codec of each type of dt700 multiline telephone. Program 84 : hardware setup for voip 84-24 : dt700 multiline codec basic information setup ...

  • Page 715

    Univerge sv8100 issue 1.0 programming manual 2 - 681 11 g729 jitter buffer max 0~270ms 80 17 jitter buffer mode 1 = static 2 = adaptive during silence 3 = adaptive immediate 3 18 --- not used --- 19 idle noise level 5000~7000 (-5000dbm~ - 7000dbm) 7000 20 echo canceller mode 0 = disable 1 = enable 1...

  • Page 716

    Issue 1.0 univerge sv8100 2 - 682 program 84 : hardware setup for voip 29 echo canceller configuration type auto (0) means that the system automatically decides a type (type 4 or type 5) of echo canceller on prg84-17 for a telephone on the basis of a seized trunk. 0~3 0 = auto 1 = type 1 2 = type 2 ...

  • Page 717

    Univerge sv8100 issue 1.0 programming manual 2 - 683 conditions none feature cross reference r voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 718

    Issue 1.0 univerge sv8100 2 - 684 program 84 : hardware setup for voip description use program 84-25 : netlink codec information basic setup to set the codec with netlink. Program 84 : hardware setup for voip 84-25 : netlink codec information basic setup level: in input data item no. Item input data...

  • Page 719

    Univerge sv8100 issue 1.0 programming manual 2 - 685 12 number of g.723 audio frames 1~2 1 = 30ms 2 = 60ms 1 13 g.723 voice activity detection mode 0 = disable 1 = enable 0 14 g.723 jitter buffer min 0~270ms 30 15 g.723 jitter buffer average 0~270ms 60 16 g.723 jitter buffer max 0~270ms 120 17 jitte...

  • Page 720

    Issue 1.0 univerge sv8100 2 - 686 program 84 : hardware setup for voip 26 tx gain 0~40 (-14dbm~+14dbm) 0 = -20dbm 1 = -19dbm : 20 = 0dbm : 39 = 19dbm 40 = 20dbm 20 27 rx gain 0~40 (-14dbm~+14dbm) 0 = -20dbm 1 = -19dbm : 20 = 0dbm : 39 = 19dbm 40 = 20dbm 20 28 audio capability priority 0~3 0 = g.711_...

  • Page 721

    Univerge sv8100 issue 1.0 programming manual 2 - 687 conditions none feature cross reference r voice over internet protocol (voip) 35 g.722 jitter buffer (min) 0~160ms 30 36 g.722 jitter buffer (average) 0~160ms 60 37 g.722 jitter buffer (max) 0~160ms 120 38 number of g.726 audio frames 1~4 1 = 10ms...

  • Page 722: 84-26 : Ipl Basic Setup

    Issue 1.0 univerge sv8100 2 - 688 program 84 : hardware setup for voip description use program 84-26 : ipl basic setup to set the ip address of ipl and the port. Program 84 : hardware setup for voip 84-26 : ipl basic setup level: in index 1 slot number 1 voip gw number 01~08 item no. Item input data...

  • Page 723

    Univerge sv8100 issue 1.0 programming manual 2 - 689 conditions none feature cross reference r voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 724: 84-27 : Ipl Basic Setup

    Issue 1.0 univerge sv8100 2 - 690 program 84 : hardware setup for voip description use program 84-27 : ipl basic setup to set the dtmf relay and the srtp mode of the ipl. Program 84 : hardware setup for voip 84-27 : ipl basic setup level: in index 1 slot number 1 input data item no. Item input data ...

  • Page 725

    Univerge sv8100 issue 1.0 programming manual 2 - 691 conditions none feature cross reference r voice over internet protocol (voip) digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 726

    Issue 1.0 univerge sv8100 2 - 692 program 84 : hardware setup for voip description use program 84-28 : dt700 multiline firmware name setup to set the firmware name to download for the ip phone. Conditions none feature cross reference r voice over internet protocol (voip) program 84 : hardware setup ...

  • Page 727

    Univerge sv8100 issue 1.0 programming manual 2 - 693 description use program 84-29 : sip-mlt codec information fixed mode setup to set the codec data of the sip-mlt when it uses multicast. Conditions none feature cross reference none program 84 : hardware setup for voip 84-29 : sip-mlt codec informa...

  • Page 728

    Issue 1.0 univerge sv8100 2 - 694 program 84 : hardware setup for voip this page intentionally left blank digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 729: 90-01 : Installation Date

    Programming manual 2 - 695 program 90 description use program 90-01 : installation date to define the installation date of the system. Conditions none feature cross reference none program 90 : maintenance program 90-01 : installation date level: in input data item no. Item input data default 01 year...

  • Page 730

    Issue 1.0 univerge sv8100 2 - 696 program 90 : maintenance program description use program 90-02 : programming password setup to set the system passwords. For password entry, the system allows eight users to be defined. Each user can have a: r unique alphanumeric name (up to 10 alphanumeric characte...

  • Page 731

    Univerge sv8100 issue 1.0 programming manual 2 - 697 default conditions p more than one extension can be in the programming mode. Feature cross reference none user no. User name password level level description 1 necii 47544 1 (mf) manufacturer level - access to all system programs. 2 tech 12345678 ...

  • Page 732: 90-03 : Save Data

    Issue 1.0 univerge sv8100 2 - 698 program 90 : maintenance program description (this program is available only via telephone programming and not through pc programming). Use program 90-03 : save data to save the programmed data on the usb flash drive. This program should be used after changing the p...

  • Page 733: 90-04 : Load Data

    Univerge sv8100 issue 1.0 programming manual 2 - 699 description (this program is available only via telephone programming and not through pc programming). Use program 90-04 : load data to load the system data from the inserted usb flash drive to the sram and flash rom in the system. Conditions p af...

  • Page 734: 90-05 : Slot Control

    Issue 1.0 univerge sv8100 2 - 700 program 90 : maintenance program description (this program is available only via telephone programming and not through pc programming). Use program 90-05 : slot control to reset or delete (uninstall) blades (slots 1~24). Delete allows you to completely uninstall the...

  • Page 735: 90-06 : Trunk Control

    Univerge sv8100 issue 1.0 programming manual 2 - 701 description (this program is available only via telephone programming and not through pc programming). Use program 90-06 : trunk control for trunk maintenance. Busy out lets you block a blade from placing outgoing calls (just like placing the blad...

  • Page 736: 90-07 : Station Control

    Issue 1.0 univerge sv8100 2 - 702 program 90 : maintenance program description (this program is available only via telephone programming and not through pc programming). Use program 90-07 : station control for extension maintenance. Conditions none feature cross reference none program 90 : maintenan...

  • Page 737: 90-08 : System Reset

    Univerge sv8100 issue 1.0 programming manual 2 - 703 description (this program is available only via telephone programming and not through pc programming). Use program 90-08 : system reset to perform a system reset. Conditions p after restoring a customer database, the system must be reset using pro...

  • Page 738

    Issue 1.0 univerge sv8100 2 - 704 program 90 : maintenance program description use program 90-09 : automatic system reset time setup to define the time for the system to automatically reset. Conditions none feature cross reference none program 90 : maintenance program 90-09 : automatic system reset ...

  • Page 739

    Univerge sv8100 issue 1.0 programming manual 2 - 705 description use program 90-10 : system alarm setup to assign a status to system alarms. You can designate an alarm as major or minor. This program also assigns whether or not the alarm is displayed to a multiline terminal and whether or not the al...

  • Page 740

    Issue 1.0 univerge sv8100 2 - 706 program 90 : maintenance program 3 2 0 communicati on fault between cd-cp00-us and other pkgs. The error occurred when communicating with the package. When the package is broken, it recognizes it as a communication fault. 1.The unit is half. 2.The power- supply volt...

  • Page 741

    Univerge sv8100 issue 1.0 programming manual 2 - 707 6 0 0 blocking the link of terminals connected with the esi package came off. • breakdown of terminal. • faulty wiring and wiring determination. • external noise. • breakdown of esi package. Confirm the terminal connected with same esi. If they wo...

  • Page 742

    Issue 1.0 univerge sv8100 2 - 708 program 90 : maintenance program 13 0 0 charge management link error the link with the charge management device came off. 1. Problem of wiring to connect main device with charge management device. 2. Problem of pc. 1. It is confirmed that there is no problem in wiri...

  • Page 743

    Univerge sv8100 issue 1.0 programming manual 2 - 709 35 0 0 cs blocking the link of the csiu and cs came off. 1. Outgoing noise. 2. Method of setting up cs. 3. Wiring to connect csiu unit with cs. 4. Hard defect of cs. 5. Hard defect of csiu. Please confirm the following matter when happening freque...

  • Page 744

    Issue 1.0 univerge sv8100 2 - 710 program 90 : maintenance program 40 0 0 cs error noti- fication 2. Cs detected the factor that the noise is generated between cs-ps, bbic reset was executed, and it was restored automatically. 1. Outgoing noise. 2. Method of setting up cs. 3. Wiring to connect csiu ...

  • Page 745

    Univerge sv8100 issue 1.0 programming manual 2 - 711 61 0 0 sip extension trouble information. It failed in the registration of the sip extension terminal. The sip extension terminal was not able to acquire dsp. • at regist to sv8100 of the sip extension terminal. • when you cannot acquire the dsp r...

  • Page 746

    Issue 1.0 univerge sv8100 2 - 712 program 90 : maintenance program 81 2 0 netlink call trouble information. The trouble occurred by the netlink relation. • the dsp resource was not able to be acquired at incoming/outgoing. • dsp of pz-32ipla was not able to be acquired. Reconfirm wiring and the syst...

  • Page 747

    Univerge sv8100 issue 1.0 programming manual 2 - 713 conditions none feature cross reference none 92 2 0 primary compulsion specification. The primary compulsion specification function was executed. • the primary compulsion specification function was executed. No action is necessary. Inf 93 2 0 netl...

  • Page 748

    Issue 1.0 univerge sv8100 2 - 714 program 90 : maintenance program description use program 90-11 : system alarm report to define the details of the system alarm report. Program 90 : maintenance program 90-11 : system alarm report level: in input data item no. Item input data default 02 report method...

  • Page 749

    Univerge sv8100 issue 1.0 programming manual 2 - 715 conditions none feature cross reference none 12 dns secondary address when alarm reports are to be e-mailed, set the dns secondary address. 0.0.0.0~255.255.255.255 0.0.0.0 13 customer name when alarm reports are to be e-mailed, enter a name to ide...

  • Page 750

    Issue 1.0 univerge sv8100 2 - 716 program 90 : maintenance program description use program 90-12 : system alarm output to set the options for the alarm report. This program has six separate menu options. Define the output port to be used as the output for system alarm report and set the system alarm...

  • Page 751

    Univerge sv8100 issue 1.0 programming manual 2 - 717 description use program 90-13 : system information output to define the output port to be used as the system information output. The baud rate for the com port should be set in program 10-21-02. Conditions none feature cross reference none program...

  • Page 752

    Issue 1.0 univerge sv8100 2 - 718 program 90 : maintenance program description use program 90-16 : main software information to display the main software information on the cd-cp00-us. Main software information can also be viewed outside of system programming by pressing feature and the 3 key on any...

  • Page 753

    Univerge sv8100 issue 1.0 programming manual 2 - 719 description use program 90-17 : firmware information to display the firmware versions of the various system blades. Conditions none feature cross reference none program 90 : maintenance program 90-17 : firmware information level: in input data ite...

  • Page 754

    Issue 1.0 univerge sv8100 2 - 720 program 90 : maintenance program description when the extension number is entered in program 90-19 : dial block release, the extension is released from the dial block restriction. Conditions none feature cross reference r code restriction program 90 : maintenance pr...

  • Page 755

    Univerge sv8100 issue 1.0 programming manual 2 - 721 description use program 90-20 : traffic report data setup to define the details of the traffic report. Program 90 : maintenance program 90-20 : traffic report data setup level: in input data item no. Item input data default 01 call traffic output ...

  • Page 756

    Issue 1.0 univerge sv8100 2 - 722 program 90 : maintenance program conditions none feature cross reference r traffic reports 09 attendant channel all busy output 0 = not detected 1~256 (report when the data reaches the defined value) 0 10 base station all busy output 0 = not detected 1~256 (report w...

  • Page 757

    Univerge sv8100 issue 1.0 programming manual 2 - 723 description use program 90-21 : traffic report output to define the output port to be used as the traffic report output. Conditions none feature cross reference r traffic reports program 90 : maintenance program 90-21 : traffic report output level...

  • Page 758

    Issue 1.0 univerge sv8100 2 - 724 program 90 : maintenance program description use program 90-22 : terminal version information to determine the hardware and firmware versions. These are read-only commands and cannot be changed. Conditions none feature cross reference r none program 90 : maintenance...

  • Page 759

    Univerge sv8100 issue 1.0 programming manual 2 - 725 description (this program is available only via telephone programming and not through pc programming). Use program 90-23 : deleting registration of ip telephones to delete the registered ip telephone from the system. Conditions none feature cross ...

  • Page 760

    Issue 1.0 univerge sv8100 2 - 726 program 90 : maintenance program description use program 90-24 : system alarm report notification time setup to set the date and time for the alarm report to print. Conditions none feature cross reference none program 90 : maintenance program 90-24 : system alarm re...

  • Page 761

    Univerge sv8100 issue 1.0 programming manual 2 - 727 description use program 90-25 : system alarm report cc mail setup to define the mail address to receive the system alarm report cc mail setup. Conditions none feature cross reference none program 90 : maintenance program 90-25 : system alarm repor...

  • Page 762

    Issue 1.0 univerge sv8100 2 - 728 program 90 : maintenance program description use program 90-26 : program access level setup to define the password access level required to change a system program. Conditions none feature cross reference none program 90 : maintenance program 90-26 : program access ...

  • Page 763

    Univerge sv8100 issue 1.0 programming manual 2 - 729 description use program 90-28 : user programming password setup to set the password used to enter the user programming mode. Conditions none feature cross reference none program 90 : maintenance program 90-28 : user programming password setup leve...

  • Page 764

    Issue 1.0 univerge sv8100 2 - 730 program 90 : maintenance program description use program 90-31 : dim access over ethernet to enable dim (diagnostic information maintenance) access over the lan, and to define the user name and password. Dim is a maintenance tool used by engineering to extract trace...

  • Page 765

    Univerge sv8100 issue 1.0 programming manual 2 - 731 description use program 90-34 : firmware information to list the package type and firmware blades installed in the system. Conditions p these programs are ‘read only.’ feature cross reference none program 90 : maintenance program 90-34 : firmware ...

  • Page 766

    Issue 1.0 univerge sv8100 2 - 732 program 90 : maintenance program description (this program is available only via telephone programming and not through pc programming). Use program 90-35 : wizard programming level setup to set the maintenance level for wizard programming. Conditions none feature cr...

  • Page 767

    Univerge sv8100 issue 1.0 programming manual 2 - 733 description (this program is available only via telephone programming and not through pc programming). Use program 90-36 : firmware update time setting to define the data for the firmware update feature. This data is available to set for the webpr...

  • Page 768

    Issue 1.0 univerge sv8100 2 - 734 program 90 : maintenance program conditions none feature cross reference none 03 update report 256 characters max. No setting this program outputs a report when the update is executed and saves one copy on the system. If a new update occurs, the new report overwrite...

  • Page 769

    Univerge sv8100 issue 1.0 programming manual 2 - 735 description use program 90-39 : virtual loop back port reset to reset to initial status. (not supported in v1000) conditions none feature cross reference none program 90 : maintenance program 90-39 : virtual loop back port reset level: in input da...

  • Page 770

    Issue 1.0 univerge sv8100 2 - 736 program 90 : maintenance program description use program 90-41 : server setting to update terminal local data to define the primary dns server address, the secondary dns server address and the data roaming server address. Conditions none feature cross reference none...

  • Page 771

    Univerge sv8100 issue 1.0 programming manual 2 - 737 description use program 90-42 : dt700 multiline terminal version information to set the hardware version and firmware version of the dt700 mlt terminal. Conditions none feature cross reference none program 90 : maintenance program 90-42 : dt700 mu...

  • Page 772

    Issue 1.0 univerge sv8100 2 - 738 program 90 : maintenance program description use program 90-43 : deleting terminal license of dt700 to delete the terminal license information delivered to the dt700 terminal. Conditions none feature cross reference none program 90 : maintenance program 90-43 : dele...

  • Page 773

    Univerge sv8100 issue 1.0 programming manual 2 - 739 description use program 90-43 : deleting terminal license of tcp interface to delete the terminal license information delivered to the terminal with a tcp interface. Conditions none feature cross reference none program 90 : maintenance program 90-...

  • Page 774

    Issue 1.0 univerge sv8100 2 - 740 program 90 : maintenance program description use program 90-45 : temporary password change for multiline telephone to change the temporary password that is set in the encryption function. Conditions none feature cross reference none program 90 : maintenance program ...

  • Page 775

    Univerge sv8100 issue 1.0 programming manual 2 - 741 description use program 90-48 : button kit information of multiline telephone to set the button kit information on a new telephone on the sv8100 system. Conditions none feature cross reference none program 90 : maintenance program 90-48 : button k...

  • Page 776

    Issue 1.0 univerge sv8100 2 - 742 program 90 : maintenance program description use program 90-49 : protection mode setup for multiline telephone to set the protection mode of each multiline (ip) telephone. Conditions none feature cross reference none program 90 : maintenance program 90-49 : protecti...

  • Page 777

    Univerge sv8100 issue 1.0 programming manual 2 - 743 description use program 90-50 : system alarm display setup to set the system alarm report display. Conditions none feature cross reference none program 90 : maintenance program 90-50 : system alarm display setup level: in input data index number 0...

  • Page 778

    Issue 1.0 univerge sv8100 2 - 744 program 90 : maintenance program description use program 90-51 : alarm setup for maintenance exchange to set the day for the maintenance exchange of parts that need regular maintenance. Program 90 : maintenance program 90-51 : alarm setup for maintenance exchange le...

  • Page 779

    Univerge sv8100 issue 1.0 programming manual 2 - 745 conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 780

    Issue 1.0 univerge sv8100 2 - 746 program 90 : maintenance program description use program 90-52 : system alarm save for the system alarm output operation. Conditions none feature cross reference none program 90 : maintenance program 90-52 : system alarm save level: in input data system id of source...

  • Page 781

    Univerge sv8100 issue 1.0 programming manual 2 - 747 description use program 90-53 : system alarm clear to clear the system alarm. Conditions none feature cross reference none program 90 : maintenance program 90-53 : system alarm clear level: in input data system id 0~50 item no. Item input data def...

  • Page 782

    Issue 1.0 univerge sv8100 2 - 748 program 90 : maintenance program description use program 90-55 : free license select to validate the free license. (this program is available only via telephone programming and not through pc programming). Conditions none feature cross reference none program 90 : ma...

  • Page 783: 90-56 : Ntp Setup

    Univerge sv8100 issue 1.0 programming manual 2 - 749 description use program 90-56 : ntp setup to set the ntp. Conditions none feature cross reference none program 90 : maintenance program 90-56 : ntp setup level: in input data item no. Item input data default 01 ntp synchronize 0 = no 1 = yes 0 02 ...

  • Page 784

    Issue 1.0 univerge sv8100 2 - 750 program 90 : maintenance program description use program 90-57 : backup recovery data to backup the system data in the flash memory on the cd-cp00-us and to make the recovery data. Conditions none feature cross reference none program 90 : maintenance program 90-57 :...

  • Page 785

    Univerge sv8100 issue 1.0 programming manual 2 - 751 description use program 90-58 : restore recovery data to select the recovery data stored in the flash memory of the cd-cp00-us. After this command is executed, the system restarts automatically. Conditions none feature cross reference none program...

  • Page 786

    Issue 1.0 univerge sv8100 2 - 752 program 90 : maintenance program description use program 90-59 : delete recovery data to select and delete the recovery data stored in the flash memory of the cd-cp00-us. Conditions none feature cross reference none program 90 : maintenance program 90-59 : delete re...

  • Page 787

    Univerge sv8100 issue 1.0 programming manual 2 - 753 description use program 90-60 : t1/isdn layer status information to display layer status information for t1/pri/bri/cd-ccta packages. Conditions p this program is read-only. Feature cross reference none program 90 : maintenance program 90-60 : t1/...

  • Page 788

    Issue 1.0 univerge sv8100 2 - 754 program 90 : maintenance program description use program 90-61 : manual slot install to manually install any package. If another package is already assigned, the new package cannot be assigned. Conditions none feature cross reference none program 90 : maintenance pr...

  • Page 789

    Univerge sv8100 issue 1.0 programming manual 2 - 755 description use program 90-62 : security id information to display the security id of the cd-cp00-us. Conditions none feature cross reference none program 90 : maintenance program 90-62 : security id information level: in input data item no. Item ...

  • Page 790: 90-63 : Dt700 Control

    Issue 1.0 univerge sv8100 2 - 756 program 90 : maintenance program description use program 90-63 : dt700 control to adjust settings of the dt700. Conditions none feature cross reference none program 90 : maintenance program 90-63 : dt700 control level: in input data item no. Item input data default ...

  • Page 791: 92-01 : Copy Program

    Programming manual 2 - 757 program 92 description (this program is available only via telephone programming and not through pc programming). Use program 92-01 : copy program to copy the data for one program to another multiline terminal, port, group, or other number. Refer to the following charts to...

  • Page 792

    Issue 1.0 univerge sv8100 2 - 758 program 92 : copy program the copy program is applicable only for the following programs: trunk port base trunk group base extension base program no. Program name note 14-01 trunk basic data setup copy all data except trunk name (item 01). 14-02 analog trunk data se...

  • Page 793

    Univerge sv8100 issue 1.0 programming manual 2 - 759 department group base 15-06 trunk access map for extension 15-07 programmable function key 15-08 incoming virtual extension ring tone setup 15-09 virtual extension ring assignment 15-10 incoming virtual extension ring tone order setup 15-11 virtua...

  • Page 794

    Issue 1.0 univerge sv8100 2 - 760 program 92 : copy program dss console base door box base conditions p using this program to copy a multiline terminal programmable function keys, copies all keys whether or not they exist on the terminal to which the programming is being copied. This may cause confu...

  • Page 795

    Univerge sv8100 issue 1.0 programming manual 2 - 761 description (this program is available only via telephone programming and not through pc programming). Use program 92-02 : delete all extension numbers to delete all extension numbers. However, the extension number of the first port is not deleted...

  • Page 796

    Issue 1.0 univerge sv8100 2 - 762 program 92 : copy program description (this program is available only via telephone programming and not through pc programming). Use program 92-03 : copy program by port number to copy extension and the data of each outside line. Conditions none feature cross refere...

  • Page 797

    Univerge sv8100 issue 1.0 programming manual 2 - 763 description (this program is available only via telephone programming and not through pc programming). Use program 92-04 : extension data swap to swap data between two extensions. The following table lists programs that use the extension data swap...

  • Page 798

    Issue 1.0 univerge sv8100 2 - 764 program 92 : copy program 15-12 conversation recording destination for extension 15-13 loop key data 15-14 programming one-touch keys 15-17 co-message waiting indication 15-18 virtual extension key enhance options 15-19 system telephone book setup for extension 15-2...

  • Page 799

    Univerge sv8100 issue 1.0 programming manual 2 - 765 conditions none feature cross reference none 24-09 call forward split settings 26-04 ars class of service 26-07 lcr cost center code table 31-02 internal paging group assignment 41-02 acd agent extension assignment for acd group 41-17 acd login mo...

  • Page 800

    Issue 1.0 univerge sv8100 2 - 766 program 92 : copy program description use program 92-05 : extension data swap password to define the 4-digit password for each extension to allow extension data swap. Conditions none feature cross reference none program 92 : copy program 92-05 : extension data swap ...

  • Page 801: 92-06 : Fill Command

    Univerge sv8100 issue 1.0 programming manual 2 - 767 description use program 92-06 : fill command to allocate the data of each extension number of each extension group or each table. The following table lists programs that use the fill command function. Program 92 : copy program 92-06 : fill command...

  • Page 802

    Issue 1.0 univerge sv8100 2 - 768 program 92 : copy program conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 803: 92-07 : Delete Command

    Univerge sv8100 issue 1.0 programming manual 2 - 769 description use program 92-07 : delete command to delete the data of each extension number of each extension group or each table. The following table lists programs that use the delete command function. Program 92 : copy program 92-07 : delete com...

  • Page 804

    Issue 1.0 univerge sv8100 2 - 770 program 92 : copy program conditions none feature cross reference none digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 805: Rogramming

    P rogramming m anual nec unified solutions, inc. Issue 1.0 digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.

  • Page 806

    Digitcom canada inc. Need support? Call 1-866-667-8357 visit us at: www.Digitcom.Ca.