1. DL manuals
  2. Xerox
  3. Software
  4. DocuPrint 180
  5. Message Manual

Xerox DocuPrint 180 Message Manual

Manual is about: Laser Printing System Print Description Language Reference

Summary of DocuPrint 180

  • Page 1

    Xerox docuprint 180 laser printing system message guide april 1998 721p85550

  • Page 2

    Xerox corporation 701 s. Aviation boulevard el segundo, ca 90245 ©1998 by xerox corporation. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory or judicial law or hereinafter granted, including without l...

  • Page 3

    Xerox docuprint 180 lps message guide iii related publications the xerox docuprint 180 laser printing system message guide is part of the ten manual reference set for your laser printing system. The entire reference set is listed in the table below. Several other related documents are also listed fo...

  • Page 4

    Iv xerox docuprint 180 lps message guide.

  • Page 5: Table Of Contents

    Xerox docuprint 180 laser printing system message guide v table of contents related publications iii notice iii introduction vii about the reference set vii xerox docuprint 180 laser printing system document set vii what the message guide contains x how the message guide is organized xi the conventi...

  • Page 6

    Table of contents vi xerox docuprint 180 laser printing system message guide 13. System verification error messages 13-1 14. Summary sheet error messages 14-1 appearance error message 14-2 appearance warning messages 14-4 fatal error messages 14-8 informational messages 14-12 master error messages 1...

  • Page 7: Introduction

    Xerox docuprint 180 lps message guide vii introduction the xerox docuprint 180 laser printing systems message guide is one of the ten manuals which make up your xerox docuprint 180 laser printing system (lps) reference set. The lps message guide provides an easy to use reference tool for quickly det...

  • Page 8

    Introduction viii xerox docuprint 180 lps message guide xerox docuprint 180 lps pdl reference this reference contains the following information: • print description language components and processes • input processing functions • output processing functions • pdl command summary • page formatting gu...

  • Page 9

    Introduction xerox docuprint 180 lps message guide ix xerox docuprint 180 lps installation planning guide this reference contains the following information: • lps basic components and options • tasks that must be accomplished before installation • preinstallation requirements • installation process ...

  • Page 10

    Introduction x xerox docuprint 180 lps message guide what the message guide contains the xerox docuprint 180 lps message guide is divided into the following chapters: chapter 1: cp (compress command) messages chapter 2: dsr (disk save and restore command) messages chapter 3: fd (forms compilation) m...

  • Page 11

    Introduction xerox docuprint 180 lps message guide xi • an order card for the customer documentation catalog, which describes other available xerox documentation • a reader comment form. Please take a few minutes to write your comments about the message guide, and any suggestions you may have for im...

  • Page 12

    Introduction xii xerox docuprint 180 lps message guide the conventions used in this guide the following conventions are used throughout this guide: • when keyed in, most commands can be shortened to three letters. For example, reset may be entered as res. Commands are shown in capital letters. • var...

  • Page 13: Cp (Compress Command)

    Xerox docuprint 180 lps message guide 1-1 1. 1 cp (compress command) messages these messages may appear during the process of compressing the system disk. (refer to your xerox docuprint 180 lps operations reference chapter on managing lps resources for additional information.) cp1010 compress now re...

  • Page 14

    Cp (compress command) messages 1-2 xerox docuprint 180 lps message guide cp2700 invalid keyin the compress command was entered incorrectly. Action reenter command correctly cp2710 keyins are not allowed at this time compress process has begun. System cannot process any other commands entered at this...

  • Page 15: Dsr (Disk Save and Restore

    Xerox docuprint 180 lps message guide 2-1 2. 2 dsr (disk save and restore command) messages these messages may appear during the process of saving all disk files on tape or restoring all files to system disk from tape. (refer to your xerox docuprint 180 lps operations reference chapter on managing l...

  • Page 16

    Dsr (disk save and restore command) messages 2-2 xerox docuprint 180 lps message guide ds8010 tape error xxxx...Dsr aborted the system has encountered a device error from which it was unable to recover after several attempts. Dsr task is aborted. Action 1. Clean the tape drive and retry the task. (r...

  • Page 17

    Dsr (disk save and restore command) messages xerox docuprint 96 lps message guide 2-3 ds9040 system error...Dsr aborted an unspecified hardware error has caused dsr task to abort. Action 1. Retry the dsr task. 2. If the problem continues, contact your systems specialist or xerox customer service. Ds...

  • Page 18

    Dsr (disk save and restore command) messages 2-4 xerox docuprint 180 lps message guide.

  • Page 19: Fd (Forms Compilation)

    Xerox docuprint 180 lps message guide 3-1 3. 3 fd (forms compilation) messages these messages may appear while forms are being compiled using forms description language (fdl). (refer to your xerox docuprint 180 lps forms creation guide for additional information.) fd0900 operator-requested abort the...

  • Page 20

    Fd (forms compilation) messages 3-2 xerox docuprint 180 lps message guide fd2720 key-in too long. Reenter the name or word entered exceeds the permitted number of characters. Action enter a different word within the permitted range. (refer to your xerox docuprint 180 lps forms creation guide.) fd273...

  • Page 21

    Fd (forms compilation) messages xerox docuprint 180 lps message guide 3-3 fd9400-fd9540 disk/file error messages fd9400 error in closing the source-input file. Fd9410 error in closing the ource-input file. Fd9420 error in closing the listing/summary file. Fd9430 error in opening the source/output fi...

  • Page 22

    Fd (forms compilation) messages 3-4 xerox docuprint 180 lps message guide.

  • Page 23: Messages

    Xerox docuprint 180 lps message guide 4-1 4. 4 hip (host interface processor) messages these messages may appear on your system controller display if printer communications have been established through the host interface processor (hip). The hip chapters in your xerox docuprint 180 lps operator gui...

  • Page 24

    Hip (host interface processor) messages 4-2 xerox docuprint 180 lps message guide hp0085 concatenated job operator display mode is ‘off’ in response to an operator command, hip will not display internal job status while in a concatenated job mode. Action none. Hp0090 job concatenation mode is ‘on’ i...

  • Page 25

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-3 hp0210 transmission aborted: job id xxxx the hip abort command was entered. The job being sent has been cancelled. Action none. Hp1010 input starting report - jid xx this is displayed while in a concatenated job mode i...

  • Page 26

    Hip (host interface processor) messages 4-4 xerox docuprint 180 lps message guide hp1130 buffer file allocation less than specified the hip buffer has less space than specified in the hip.Cmd file at installation. There may not be enough space to hold the entire job being sent. Action 1. Delete unne...

  • Page 27

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-5 hp1172 log file empty, nothing to print. You have entered the hip show log [prn] command and there are no entries in the log file. Action none. Hp1180 no echo servers on list there are no echo servers on list. Action n...

  • Page 28

    Hip (host interface processor) messages 4-6 xerox docuprint 180 lps message guide hp1210 host online. Accepting all jobs the hip online all command was entered. The printer and remote host are communicating, and the host is sending jobs to the hip buffer. All print and nonprint files (fonts, forms, ...

  • Page 29

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-7 hp1260 interface busy - cannot send file(s) the hip send command was entered. The interface is busy and is unable to send files from the host at this time. Action wait for current transmission to complete. Hp1265 onlin...

  • Page 30

    Hip (host interface processor) messages 4-8 xerox docuprint 180 lps message guide hp1299 xpaf communications recovered hip can now receive data via the xpaf communication mode. Data received but not yet written to system disk will be copied from memory (saved at system error restart) and written to ...

  • Page 31

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-9 hp1420 end of test 3 analysis the system failed diagnostic test 3. Hip has completed analysis of test 3 results and has identified the data line that has failed. This message follows message hp9431 or hp9432. Action no...

  • Page 32

    Hip (host interface processor) messages 4-10 xerox docuprint 180 lps message guide hp2120 insufficient disk space for host buffering fewer than 256 blocks are available for hip buffer space. There is not sufficient space to receive and buffer files. The system cannot go online. Action 1. Delete file...

  • Page 33

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-11 hp2160 enter ‘hip show log continue’ for more there are more than 20 entries in the log and you must enter hip show log continue to view additional screens. Action none. Hp2165 insufficient disk space for log files. Y...

  • Page 34

    Hip (host interface processor) messages 4-12 xerox docuprint 180 lps message guide hp2300 command error at: part of command in error the command part indicated was entered incorrectly. Action reenter the command correctly. (refer to the hip chapter in your xerox docuprint 180 lps operator guide.) hp...

  • Page 35

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-13 hp2344 cannot change: job does not exist. The jid specified does not exist in the hip job queue. Action none. Hp2345 cannot change: output file already exists the file specified is already resident on the disk. Action...

  • Page 36

    Hip (host interface processor) messages 4-14 xerox docuprint 180 lps message guide hp2500 change of job xxxx to file file-type failed: unrecoverable i/o error yy. The change command failed due to the error values specified in this message. These error values will be one of the following: • 03disk co...

  • Page 37

    Hip (host interface processor) messages xerox docuprint 180 lps message guide 4-15 hp8250 fatal protocol violation detected commands used violate the higher-level software protocols used to communicate between the xerox docuprint 180 lps and the host. The host will be advised to restart communicatio...

  • Page 38

    Hip (host interface processor) messages 4-16 xerox docuprint 180 lps message guide hp9420 host not communicating. See host for reason the hip diagnostic command was entered. The system failed test 1: (see explanation for message hp9400) or test 2: system was unable to send a command on oemi and in t...

  • Page 39: Messages

    Xerox docuprint 180 lps message guide 5-1 5. 5 ifu (interpress font utility) messages these messages appear when the interpress font utility program (refer to your xerox docuprint 180 lps operations reference chapter on hip-accessed communicating modes for additional information.) the meaning of ter...

  • Page 40

    Ifu (interpress font utility) messages 5-2 xerox docuprint 180 lps message guide if1100 font family xxxx this is an informational message indicating the font family name being compiled by the ipfnts command. Action none. If1102 adding xxxx point xxxx this is an informational message indicating the o...

  • Page 42

    Ifu (interpress font utility) messages 5-4 xerox docuprint 180 lps message guide if1503 replacing with substitute character this is an informational message advising that a particular character is being replaced with the substitute character. Action none. If1504 adding as rendered character the requ...

  • Page 43

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-5 if1629 parser error there is a problem with parsing the parameters within a command. Action none. If2000 aborting add the add command to add font families to the interpress or data center font environments has been abor...

  • Page 44

    Ifu (interpress font utility) messages 5-6 xerox docuprint 180 lps message guide if2025 unknown parameter on add command one of the parameters (descriptive elements) in the add command is incorrect. Action check the add command and reenter it correctly. If2030 command not recognized an invalid ifu c...

  • Page 45

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-7 if2050 please mount the next volume, number x this message instructs you to mount the next tape or cartridge volume. A message will then ask if you want to continue or abort the operation. Action 1. Mount the tape or ca...

  • Page 46

    Ifu (interpress font utility) messages 5-8 xerox docuprint 180 lps message guide if2061 attempting to append to a non ifu copy medium. Mount correct medium or initialize the medium and retry appending an ifu copy write file to the end of a non ifu copy medium is not permitted. Action 1. Mount the co...

  • Page 47

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-9 if2098 are you sure you want to abort? (enter ‘y’ or ‘n’) an abort command was entered during the ifu copy read process. Action enter n. Note: the font structure on the disk may be corrupted if the process is aborted. I...

  • Page 48

    Ifu (interpress font utility) messages 5-10 xerox docuprint 180 lps message guide if2212 the wrong floppy has been mounted a floppy disk has been mounted out of sequence for reading in. A message will follow asking if you want to continue or quit this operation. Action mount the correct floppy if yo...

  • Page 49

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-11 if2235 please confirm deletion of wildcarded interpress font upon entering the ifu delete command, you are asked by the system to confirm this operation by entering c to continue or a to abort. Action enter c or a as a...

  • Page 50

    Ifu (interpress font utility) messages 5-12 xerox docuprint 180 lps message guide if2250 medium must be tape or cartridge. Magnetic tape or cartridge are the only media possible for the add command (some commands do not accept floppy disks). Action reenter the command specifying either magnetic tape...

  • Page 51

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-13 if2336 map x was not found in ipfnts.Sys the requested interpress character mapping is not found in the character mapping tables that are stored in the ipfnts.Sys file. Action modify the font profile to refer to an exi...

  • Page 52

    Ifu (interpress font utility) messages 5-14 xerox docuprint 180 lps message guide if2410 orientation parameter was not found in dcfonts statement orientation (i.E., portrait, landscape, iportrait, and ilandscape) has not been specified in the dcfonts statement in the font profile. Action 1. Correct ...

  • Page 53

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-15 if2428 orientation x was not found in easy values some orientations requested are not contained in the fis font master. Action none. If2434 missing name parameter on fonts statement an interpress font name is missing f...

  • Page 54

    Ifu (interpress font utility) messages 5-16 xerox docuprint 180 lps message guide if2456 warning: substitute character requires extended metrics substitution of the requested character requires extended metrics, which may reduce interpress performance. Action none. If2701 syntax error: expecting a c...

  • Page 55

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-17 if2708 syntax error: unexpected token x encountered the character or symbol indicated in the message is incorrectly included in the command line. Action reenter the command, omitting the incorrect character or symbol. ...

  • Page 56

    Ifu (interpress font utility) messages 5-18 xerox docuprint 180 lps message guide if2720 syntax error in statement x an error exists in the given statement. Action check and reenter the command, using the corrected statement. If2730 semantic error in statement x an error exists in the meaning of the...

  • Page 57

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-19 if2852 invalid ftype parameter the ftype parameter in the font profile is incorrect. Action 1. Reenter the ftype parameter to include the correct parameter (either standard or extended). 2. Retry the add command. If285...

  • Page 58

    Ifu (interpress font utility) messages 5-20 xerox docuprint 180 lps message guide if2860 invalid sections parameter the section parameter in the general statement of the font profile is incorrect. Action 1. Verify and reenter the appropriate sections parameter in the font profile. 2. Reenter the add...

  • Page 59

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-21 if2903 jsl syntax err x - unclosed string there is an unclosed string in the jsl file. Action 1. Correct the jsl file to include a string enclosed in single quotes. 2. Retry the command. If2904 jsl syntax err x string ...

  • Page 60

    Ifu (interpress font utility) messages 5-22 xerox docuprint 180 lps message guide if2910 jsl syntax err x - expecting an equal sign after y the system requires an equal sign (=) after the given character in the jsl file. Action 1. Correct the jsl file to include the required equal sign. 2. Retry the...

  • Page 61

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-23 if2950 jsl file x will not open the requested jsl file in the ipfnts statement cannot be opened. Action verify and reenter the jsl file name correctly. If2951 jsl statement is too large to be processed the jsl statemen...

  • Page 62

    Ifu (interpress font utility) messages 5-24 xerox docuprint 180 lps message guide if2973 no valid characters were found in character set x in processing the fis master, the substitute character’s raster bitmap is either missing or defective. Action 1. Correct the chars parameter of the font profile....

  • Page 63

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-25 if4111 fis processing error; aborting add due to an error in the fis master, the add command is being aborted. This error is probably the result of a previous error which should have displayed a message. Action contact...

  • Page 64

    Ifu (interpress font utility) messages 5-26 xerox docuprint 180 lps message guide if7000 ** - write lock protection error - ** a write operation could not be completed successfully, probably because the write ring is not present on the magnetic tape. Action 1. Put a write enable ring on the magnetic...

  • Page 65

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-27 if7108 temporary file x of decomposed fis will not open there is an ifu temporary access problem, probably due to a disk error or insufficient space. Action 1. Compress the disk and retry the command. 2. If the problem...

  • Page 66

    Ifu (interpress font utility) messages 5-28 xerox docuprint 180 lps message guide if7705 family name directory will not open the fdr package is either not on the system or is corrupted action execute the ifu ipfnts command sequence to recreate the fdr file if7800 interpress decomposer initialization...

  • Page 67

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-29 if7902 cmt package error an error occurred while the system was processing the character mapping table, probably due to a disk error or insufficient space. Action 1. Compress the disk and retry the command. 2. If the p...

  • Page 68

    Ifu (interpress font utility) messages 5-30 xerox docuprint 180 lps message guide if7909 sample command failed, retry the command file ifsam$.Cmd, used to print out the fonts specified in the sample command, does not exist because the fopen command failed. This is a probable disk error. Action conta...

  • Page 69

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-31 if7914 ipm input from file x, block y, failed the system failed in an attempt to read a block from an ipm file. The file is either corrupted or does not exist on the system. Action 1. Delete the ipm files on the system...

  • Page 70

    Ifu (interpress font utility) messages 5-32 xerox docuprint 180 lps message guide if8103 cmt symbol table has overflowed by map x there was not enough space in the character mapping table when adding the next symbol. Action contact your systems specialist or xerox customer service. If8104 cmt entry ...

  • Page 71

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-33 if8203 error: from ipf_open ( ) the system is unable to open the ipfnts.Sys file. Either the file is not on the system or is corrupted or there is a software problem. Action 1. Check if the ipfnts.Sys file is on the sy...

  • Page 72

    Ifu (interpress font utility) messages 5-34 xerox docuprint 180 lps message guide f8210 error: from ipf_read_block ( ) entry ( ) an error occurred when the system attempted to access the ipfnts.Sys file. Either the file is not on the system or is corrupted, or there is a software problem. Action 1. ...

  • Page 73

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-35 if8214 error: from dlm_add ( ) an error occurred when the system attempted to access the ifudlm.Sys file. Either the file is not on the system or is corrupted, or there is a software problem. Action 1. Check if the ifu...

  • Page 74

    Ifu (interpress font utility) messages 5-36 xerox docuprint 180 lps message guide if8218 error: from ffm_delete ( ) an error occurred when the system attempted to access the ifuffm.Sys file. Either the file is not on the system or is corrupted, or there is a software problem. Action 1. Check if the ...

  • Page 75

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-37 if8401 fis font request failed with emt return code x the fis font request cannot be processed due to the emt (emulator trap) return code shown. Action contact your systems specialist or xerox customer service. If8402 ...

  • Page 76

    Ifu (interpress font utility) messages 5-38 xerox docuprint 180 lps message guide if8409 missing font mapping header at file offset? The text that was just read from the written file on the medium was not as expected. The format of the file written by the write command is either corrupted, the read ...

  • Page 77

    Ifu (interpress font utility) messages xerox docuprint 180 lps message guide 5-39 if9000 **- device is not ready -** the medium specified was not available when the operation was attempted, or during the operation. Action 1. Prepare the medium for operation and retry the command. 2. If the retry fai...

  • Page 78

    Ifu (interpress font utility) messages 5-40 xerox docuprint 180 lps message guide if9099 device error x an input/output operation on the medium failed. Action refer to the error message appearing on the system controller keyboard display and take appropriate action. If9101 read error on ipfnts.Sys t...

  • Page 79: Oss (Operating System

    Xerox docuprint 180 lps message guide 6-1 6. 6 oss (operating system software) messages the os messages appearing on your system controller display are generated by the operating system software (oss). These messages are assigned to levels 0 through 9. The higher the number, the more serious the pro...

  • Page 80

    Oss (operating system software) messages 6-2 xerox docuprint 180 lps message guide os0060 resuming full performance the printer had been operating in a reduced performance mode due to page complexity and is now returning to full performance. Action none. Os0200 main tray selected this message confir...

  • Page 81

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-3 os0320 output tray 2 selected one of the following commands was entered: -select -select 2 -select auto -select 2,sample output will be delivered to stacker tray 2. The printer control console displays: output tray 2 ...

  • Page 82

    Oss (operating system software) messages 6-4 xerox docuprint 180 lps message guide os0510 input stopped the stop or stop i command was entered, or the key was pressed. The system has stopped transmitting data and is reading it onto the system disk. Action to restart: enter continue or continue i com...

  • Page 83

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-5 os0730 finishing exerciser utility: successful exit. Fex has successfully completed. Action none. Os0731 updating the iot‘s memory with test profile info fex is loading into the printer‘s non-volatile memory the new f...

  • Page 84

    Oss (operating system software) messages 6-6 xerox docuprint 180 lps message guide os0801 nvm update complete the periodic acquisition of information from the printer control console has been completed. Action none. Os0830 attention light enabled. The light enable command is entered and accepted. Ac...

  • Page 85

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-7 os0853 mode: xxx housing, -plex during pqa, this message identifies the housings being adjusted and whether simplex or duplex printing is specified for the current pqa operation. This message may accompany other relat...

  • Page 86

    Oss (operating system software) messages 6-8 xerox docuprint 180 lps message guide os0862 substituting color for all other inks for this report after you enter a valid substitute ink command, this message tells you the primary color which is being substituted for all primary colors (including black)...

  • Page 87

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-9 os0873 substituting color for color for this job after you enter a substitute ink command, this message tells you which primary color is being substituted for the specified color in your current job. Action none. Os08...

  • Page 88

    Oss (operating system software) messages 6-10 xerox docuprint 180 lps message guide os level 1: information informs you of system activities. Os1000 ready for commands hh:mm:ss the system is ready to process commands entered. (the time of day is displayed after the message.) action enter the command...

  • Page 89

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-11 os1006 printer is not available; printer is being serviced the printer is unable to respond to the entered command because the xerox service representative is performing diagnostic tests. The printer control console ...

  • Page 90

    Oss (operating system software) messages 6-12 xerox docuprint 180 lps message guide os1010 starting job xxxx the system is initiating processing for the indicated job. Action none. Os1011 starting diagnostic print job the system diagnostic interface (sdi) task is involved. Action none. Os1012 alun$ ...

  • Page 91

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-13 os1017 physical device %0 substituted for logical device %1. The device substitution specified in the sub dev command has taken place. Action none. Os1020 job xxxx has completed input phase all requested manipulation...

  • Page 92

    Oss (operating system software) messages 6-14 xerox docuprint 180 lps message guide os1080 start accounting report the report or account command was entered. The system is compiling and printing, or writing to magnetic tape, a report of system usage data. Action none. Os1085 billing report starting ...

  • Page 93

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-15 os1101 fcg working. Fcg tasks are in progress. Action none. Os1102 finishing exerciser is reconnecting to the iot. After completing the test print job, fex is reconnecting communications with the printer and restorin...

  • Page 94

    Oss (operating system software) messages 6-16 xerox docuprint 180 lps message guide os1132 --- nvm finishing locations --- this message lists the values that are currently in the printer‘s non- volatile memory. Action save (write down) these values so that you can restore them should an fex communic...

  • Page 95

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-17 os1155 request rejected, diagnostic job already in progress a diagnostic print job is already being processed; additional requests are rejected. Action none. Os1160 no pages waiting to be drained the drain command wa...

  • Page 96

    Oss (operating system software) messages 6-18 xerox docuprint 180 lps message guide os1195 undefined ink: color the ink you specified (represented by the word color in the message shown) is incorrect. Action 1. Check to make sure that the ink name is entered correctly. 2. If the message reappears, c...

  • Page 97

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-19 os1240 status command inoperative the key was pressed or the jobs command was entered. The system is unable to display status because a file was not created at sysgen due to insufficient disk space. Action 1. Delete ...

  • Page 98

    Oss (operating system software) messages 6-20 xerox docuprint 180 lps message guide os1263 form paper size out of range: xxxxxx.Xxx paper size for form specified in the jsl is not supported by the iot. Action contact your systems specialist. Os1264 barcode sequence mismatch the iot detected a sequen...

  • Page 99

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-21 os1275 command file suspended the .Pause command was entered. Command file processing is suspended for an unspecified period of time. Or the .Wait command was entered. Command file processing is suspended until the c...

  • Page 100

    Oss (operating system software) messages 6-22 xerox docuprint 180 lps message guide os1285 message does not exist. Requesting task: ******; os1287 should not display this message. Requesting task: ******; the message file containing the message that should be displayed for the indicated task does no...

  • Page 101

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-23 os1294 invalid paper tray selected. Command ignored a command was entered that refers to a (feeder) tray not in the printer configuration, e.G., (feeder) trays 3 and 4 can only be selected when your printer has a hig...

  • Page 102

    Oss (operating system software) messages 6-24 xerox docuprint 180 lps message guide os1310 number of active fonts is nn the maximum number of fonts per print job the system will attempt to keep in memory is (number 0-128). This message appears at installation when font memory space is allocated. Act...

  • Page 103

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-25 os1326 already in lockout mode during service activities, the lockout mode has already been initiated. Action none. Os1329 binfull criteria: n% ream threshold, n% boundary after entering the binfull command with thre...

  • Page 104

    Oss (operating system software) messages 6-26 xerox docuprint 180 lps message guide os1335 xps accounting stopped: no disk space for files xps is unable to accumulate accounting data because there is no disk space for files. Action none. Os1336 xps accounting enabled xps received a request from the ...

  • Page 105

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-27 os1400 sample ignored...Printer idle the key was pressed while the printer was not in the process of imaging a page. The system could not produce a sample page when the key was pressed. The printer control console di...

  • Page 106

    Oss (operating system software) messages 6-28 xerox docuprint 180 lps message guide os1416 sample not allowed—printer is busy the sample request is not allowed at this time. Action retry at a later time. Os1417 interpress master not found; check start command the file from the start command “disc:fn...

  • Page 107

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-29 os1460 cannot space if “reports:” is specified with start cmd the space n reports command was entered. The system cannot process the command because the reports option of the start command was entered when the job wa...

  • Page 108

    Oss (operating system software) messages 6-30 xerox docuprint 180 lps message guide os1535 formatting wp exception index page exception page is being created, indicating errors in report being sent from workstation. Page will be delivered as last page of report. Action 1. Check exception page for lo...

  • Page 109

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-31 os1551 inappropriate disk file type specified an incorrect disk file type has been entered. Action check the file type and reenter it correctly. (refer to your xerox docuprint 180 lps operations reference chapter on ...

  • Page 110

    Oss (operating system software) messages 6-32 xerox docuprint 180 lps message guide os1557 creating file x.Img. The file indicated has been sent from the host and is being created on the system disk. Or file %0 %1 created this file has just been created on the system disk. No action necessary. Actio...

  • Page 111

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-33 os1563 sef file not found you have specified that the font mappings you wish to use in the job are contained in a file that does not exist in the system. Job processing will continue using the font specified in the p...

  • Page 112

    Oss (operating system software) messages 6-34 xerox docuprint 180 lps message guide os1627 local density problem rasterization complete a page with a local density problem has been rasterized; i.E., a bitmap image of the page has been produced. The printer will now cycle up and print the problem pag...

  • Page 113

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-35 os1727 this option is not supported on this software version the printer software does not support the command entered. Action check the printer‘s reference material for the desired command. Os1728 btext command not ...

  • Page 114

    Oss (operating system software) messages 6-36 xerox docuprint 180 lps message guide os1766 input tape device initialized to x: this message names the selected input tape device being used. Action none. Os1770 “online” input is waiting for data the start and online commands were entered. The system i...

  • Page 115

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-37 os1810 printing aborting the abort o command was entered. The job currently printing is being discontinued. Sheets in the paper path are being sent to a stacker tray. The printer control console displays: output stop...

  • Page 116

    Oss (operating system software) messages 6-38 xerox docuprint 180 lps message guide os1825 job queue has been flushed the drain command was entered. All data in queue has printed. Action none. Os1830 printing 1 copy of current report the “print 1” option was selected in response to “disk saturation”...

  • Page 117

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-39 os1927 this system does not support ethernet processing the command entered applies only to ethernet. The system is not equipped with the ethernet controller option for operating on the network. Action none. Os1928 c...

  • Page 118

    Oss (operating system software) messages 6-40 xerox docuprint 180 lps message guide os1962 the ‘pqa continue’ parameter is not allowed with the current selections. For the xerox docuprint 180 lps, you have entered the pqa command with the continue option, but have not met the requirements that allow...

  • Page 119

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-41 os1970 fex exiting. Unable to run during a print job. Fcg exiting. Unable to run during a print job. (4050/4090/4650 only) the lps printer is actively running a print job. Therefore, fex cannot begin processing your ...

  • Page 120

    Oss (operating system software) messages 6-42 xerox docuprint 180 lps message guide os1979 nvm address . . . (4050/4090/4650) this message either lists a series of four wire management or seven third party device parameters for you to enter or simply gives the current values. N8 :% wire remaining on...

  • Page 121

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-43 os1982 fcg exiting. Invalid profile encountered. (4050/4090/4650 only) the system cannot accept the parameters or values you have entered. The cause may be incorrect syntax, too many characters, etc. This message is ...

  • Page 122

    Oss (operating system software) messages 6-44 xerox docuprint 180 lps message guide os level 2: routine maintenance states a condition and explains what action(s) to take. Os2000 enter ‘continue o’ to resume printing or select ‘continue o’ to resume printing printing was interrupted by the entered c...

  • Page 123

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-45 os2004 paper trays not set for same size the length guides of the feeder trays are adjusted for different paper lengths. Automatic switching will not be possible. (this is an information message appearing at the star...

  • Page 124

    Oss (operating system software) messages 6-46 xerox docuprint 180 lps message guide os2007 empty sample output tray the sample tray contains more than 100 sheets. It must be emptied for printing to resume. The printer control console displays: empty sample tray action remove output from the sample t...

  • Page 125

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-47 os2025 remount volume n for next copy of report. Con i when ready. This message appears when making multiple copies of multi-volume reports in a noncollate mode. This includes reports with copy- sensitive cmes and mu...

  • Page 126

    Oss (operating system software) messages 6-48 xerox docuprint 180 lps message guide os2055 establishing communications with iot. The output task is establishing communication with the printer. Until communications are established, printer status information is not available. Action none. Os2056 fini...

  • Page 127

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-49 os2070 paper tray 2 is empty no paper remains in feeder tray 2. The printer control console displays one of the following: both trays set for _._x_._" paper both trays set for _x_mm paper paper tray 2 is empty. Tray ...

  • Page 128

    Oss (operating system software) messages 6-50 xerox docuprint 180 lps message guide os2091 no available trays are ready the tray(s) available for your job are not ready to be used. Possible causes may be that they are empty, have the wrong type of stock, are not properly latched, etc. Action 1. Chec...

  • Page 129

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-51 os2220 output tray 2 is full stacker tray 2 contains its capacity amount of sheets. The printer control console displays one of the following: job is printing. Output tray 2 is full. Output tray 2 is full printer is ...

  • Page 130

    Oss (operating system software) messages 6-52 xerox docuprint 180 lps message guide os2260 paper in selected tray too large. Change if desired. The paper length guide in the selected tray is set for paper of a larger size than that set at mini-sysgen. Printing stops. (this message is followed by mes...

  • Page 131

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-53 os2262 paper in cluster xxxx is too large the specified cluster contains paper that is larger than that specified by the print job action change the paper in the specified cluster. Or change the feed command. Or pres...

  • Page 132

    Oss (operating system software) messages 6-54 xerox docuprint 180 lps message guide os2288 warning: current select command overrides data destination value. Change select command or con o the data stream contains a destination=export statement, and the current operator select keyin is other than aut...

  • Page 133

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-55 os2296 log printing not allowed until system status=’idle the system must be offline and not printing to process a log print request. Action complete or abort any current jobs, enter the offline command and then resu...

  • Page 134

    Oss (operating system software) messages 6-56 xerox docuprint 180 lps message guide os2400 printer misfeed detected. Check paper supply. Paper was improperly fed from the main and/or auxiliary feeder tray, causing a jam condition. Action release the feeder belt and check both feeder trays, removing ...

  • Page 135

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-57 os2512 color housing: not present this message is displayed if a color housing is not installed in the printer before the printer doors are closed. Action none. Os2513 color housing is needed for this report the prin...

  • Page 136

    Oss (operating system software) messages 6-58 xerox docuprint 180 lps message guide os2570 vary system offline at the host and enter ‘continue i’ or vary system offline at the host and select ‘continue i’ the offline command was entered. Action 1. Follow procedures required to take the printer offli...

  • Page 137

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-59 os2610 improper ink-name list specification the ink-name list you have specified does not conform to ink-name list syntax. For example, you may have used double instead of single quotes to identify the ink-names. Act...

  • Page 138

    Oss (operating system software) messages 6-60 xerox docuprint 180 lps message guide os2660 do you want to enter accounting? [y or n] or do you want to enter accounting? Type y for 2000 reports or n for 100 reports. (this message appears at the end of the sysgen process.) to set the size of the statu...

  • Page 139

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-61 os2673 enter the sub ink command or abort the print job. The printer requires a primary color that is not currently loaded. This message prompts you with two available options: action enter a substitute ink command o...

  • Page 140

    Oss (operating system software) messages 6-62 xerox docuprint 180 lps message guide os2679 report aborted per job request the printer requires a primary color that is not currently loaded. The job specifies that the report be aborted in this situation. Action none. Os2680 print quality adjustment is...

  • Page 141

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-63 os2691 ensure proper stock is loaded for print job this message appears after print quality adjustment is completed when stop was specified in the pqa command, or if you have pressed the stop button or entered pqa ca...

  • Page 142

    Oss (operating system software) messages 6-64 xerox docuprint 180 lps message guide os2712 command not allowed while task is running. The command entered cannot be processed while the current task is ongoing. Action 1. Abort the current task or wait until it is completed. 2. Reenter the desired comm...

  • Page 143

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-65 os2730 requested task not found in system. Check and retry. A command was requested that the system cannot perform, or a task name was keyed in incorrectly. Action 1. Verify the task name and enter it correctly. 2. I...

  • Page 144

    Oss (operating system software) messages 6-66 xerox docuprint 180 lps message guide os2750 job not found. Check and retry. The job id number entered in the start command was not sent. Action 1. Verify that the job number was entered correctly. 2. Reenter the start command. 3. If the message reappear...

  • Page 145

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-67 os2820 task not allowed till system status = ‘idle’ the system must be offline and not printing to process the requested task. The message also appears if the rewind command is entered or the rewind button is pressed...

  • Page 146

    Oss (operating system software) messages 6-68 xerox docuprint 180 lps message guide os2860 approaching disk saturation. The print file is nearly full. Input is slowing until enough data is printed to free some cylinders on the system disk. Action none. Os2865 leaving disk saturation. Enough data has...

  • Page 147

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-69 os2885 max number of fonts exceeded. Jde called for more fonts per page than were specified at installation. The job is being aborted. The default fonts value is 32. Action 1. Enter the jde/djde command calling for a...

  • Page 148

    Oss (operating system software) messages 6-70 xerox docuprint 180 lps message guide os2922 enter the total number of sets to create: this is one of a series of prompts for information to develop the fex test case. This message is followed by messages os2923, os2924, os2008, and os1136. Action enter ...

  • Page 149

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-71 os level 3: printer problem indicates specific xerox docuprint 180 lps problems and explains what action(s) to take. Os3001 check printer doors and top covers a door or cover on the printer is not closed correctly. T...

  • Page 150

    Oss (operating system software) messages 6-72 xerox docuprint 180 lps message guide os3003 paper tray 2 fault--see message at printer feeder tray 2 has not risen completely, or a paper jam has occurred at the area indicated on the printer control console display. The printer control console displays...

  • Page 151

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-73 os3005 unusable sheets cleared to sample tray. The printer is purging any pages that are damaged or have poor print quality. Pages will be delivered to the sample tray and printing will resume where it was stopped. T...

  • Page 152

    Oss (operating system software) messages 6-74 xerox docuprint 180 lps message guide os3008 transparencies loaded--print simplex to sample tray. Transparencies were loaded in selected tray. Jsl did not specify simplex printing or delivery to the sample tray. The job will not print. The printer contro...

  • Page 153

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-75 os3010 printer is warming up. The printer is unable to respond to the entered command because the fuser has cooled to below operating temperature. Action 1. Wait for the fuser to reheat (the warmup light on the syste...

  • Page 154

    Oss (operating system software) messages 6-76 xerox docuprint 180 lps message guide os3012 paper tray 3 fault -- see message at printer. Feed tray 3 has not risen completely or a paper jam has occurred at the area indicated on the printer control console display. Action 1. Press the i button on the ...

  • Page 155

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-77 os3025 if fault continues enter ‘sel tray’ or ‘abort o’ or a fault in the collection area of the stitcher/stacker has occurred (followed by message os2000 press continue to resume printing). Action press the key to r...

  • Page 156

    Oss (operating system software) messages 6-78 xerox docuprint 180 lps message guide os3400 printer jam... See printer message. A paper jam has occurred at the area indicated on the printer control console display. The printer control console displays one of the following: check for paper in area 6. ...

  • Page 157

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-79 os3710 set integrity problem. Partial set ejected. The integrity of the current set in the stitcher/stacker‘s collection area is questionable; i.E., a page has been skipped. Action 1. Check the output. 2. Press the k...

  • Page 158

    Oss (operating system software) messages 6-80 xerox docuprint 180 lps message guide os level 4: system or tape problem states a problem and explains what action(s) to take. Os4010 cannot find end of tape reflector strip. ‘continue i’ the system did not encounter the end of tape (eot) label. Action 1...

  • Page 159

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-81 os4150 input drive is offline. ‘continue i’ when it is ready. The start or move command was entered while the tape drive was not online to the printer. Action 1. Press the on line button on the tape drive. 2. Enter t...

  • Page 160

    Oss (operating system software) messages 6-82 xerox docuprint 180 lps message guide os4500 bad block on input medium. Do one of the following: software has encountered an unreadable block. Action 1. Do one of the following: * move -1 blocks to retry read enter the move -1 blocks and continue i comma...

  • Page 161

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-83 os4651 output has recovered to page boundary. Automatic job recovery has been initiated after a system rollover. Output has resumed printing at the page where the software failure occurred. Action follow instructions...

  • Page 162

    Oss (operating system software) messages 6-84 xerox docuprint 180 lps message guide os4820 power interruption. A power failure has occurred, or the system was inadvertently turned off. Action reboot the system when power is restored. Os4900 system disk write protected: reset write protect and enter ...

  • Page 163

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-85 os level 6: job integrity identifies possible errors affecting output and what action(s), if any, to take. Os6000 insufficient memory for ‘acctinfo’; continue or abort? Jsl specified the ‘acctinfo’ option of the rsta...

  • Page 164

    Oss (operating system software) messages 6-86 xerox docuprint 180 lps message guide os6010 tape "label error" messages os6010 label error: invalid label format; continue or abort? Os6011 label error: vol 1; continue or abort? Os6012 label error: hdr 1; continue or abort? Os6013 label error: uhl, tm,...

  • Page 165

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-87 c. If there are no jsl errors, enter the start n, dump command to obtain a tape dump for analysis. D. Recreate the job with correct tape labels. (refer to your xerox docuprint 180 lps tape formats manual.) note: chec...

  • Page 166

    Oss (operating system software) messages 6-88 xerox docuprint 180 lps message guide os6102 disk read error - rtext file. The rtext statement is entered incorrectly in jde. The system cannot read it. Action 1. Press the key to resume printing. The rtext message will not print. Or enter the abort job ...

  • Page 167

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-89 os6190 graphic file xxxxxxx not found. The graphic file specified by jde does not exist on the system disk. The job will abort. Action 1. Reload the desired file onto the system disk. (refer to your xerox docuprint 1...

  • Page 168

    Oss (operating system software) messages 6-90 xerox docuprint 180 lps message guide os6195 page interleaved graphic xxxxxx read but not referenced. A graphic interleaved with text is being input but is not referenced by a djde. The graphic will not be printed. Action 1. Recode djde, referencing the ...

  • Page 169

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-91 os6300 current report saturates disk. Enter option: “continue i” - continue multicopy mode. The report currently being input exceeds the capacity of the print file. Select one of the following: action enter the conti...

  • Page 170

    Oss (operating system software) messages 6-92 xerox docuprint 180 lps message guide os6500 cannot validate first data record; space to next report. The tape record or block does not conform to the description in jsl. Action 1. Enter the space 1 reports command to go to the next report. Recreate the ...

  • Page 171

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-93 os6561 interpress error code = nn. An error was detected by the raster image processor (rip). This error message matches the error message on the interpress summary sheet for the document. The only code expected is 3...

  • Page 172

    Oss (operating system software) messages 6-94 xerox docuprint 180 lps message guide os6650 input has recovered to next report in job. Job recovery has been initiated after a software failure. After the second attempt, the system is unable to recover data for the current report. Input has moved to th...

  • Page 173

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-95 os6680 form paper size too large. Form will not be printed. The paper size specified for the form called up for the current job is larger than the size specified by the papersize statement in jsl. Input is stopping. ...

  • Page 174

    Oss (operating system software) messages 6-96 xerox docuprint 180 lps message guide os6709 djde processing error: sef file not found. The system cannot process your djde because the short-edge-feed (sef) mapping file requested is not present in the system. Action verify the sef mapping file-name and...

  • Page 175

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-97 os6713 djde processing error: font file not found. Os6714 djde processing error: form file not found. Os6715 djde processing error: pde file not found. Os6716 djde processing error: form font not found. Os6717 djde p...

  • Page 176

    Oss (operating system software) messages 6-98 xerox docuprint 180 lps message guide os6722 djde processing error: maximum forms/fonts exceeded. Djde specified a pde calling for forms and/or fonts in excess of the system maximum. Action 1. Recode the djde with fewer fonts/forms. (refer to your xerox ...

  • Page 177

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-99 os6729 djde proc. Error: feed used but no stockset in effect. The feed command was used but a stockset statement is not in effect. Action reenter the djde command, specifying a stockset. (refer to your xerox docuprin...

  • Page 178

    Oss (operating system software) messages 6-100 xerox docuprint 180 lps message guide os6735 file processing error—illegal destination file type. The file specified in djde contains a 3-character file type extension not in the lps disk directory; or file has one of the following extensions: .Osd, .Sa...

  • Page 179

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-101 os6751 insufficient dynamic memory for word processing link job. Not enough dynamic memory was available for linked word processing files. Linked files are processed up to the point where memory was exhausted. Actio...

  • Page 180

    Oss (operating system software) messages 6-102 xerox docuprint 180 lps message guide os6760 font char width table missing - word proc. Aborting job. An old (pre-v10 version) font file has been loaded. It cannot be used for cwp jobs. Job is aborting. Action 1. Restart job, using correct font tape. 2....

  • Page 181

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-103 os6820 improper palette-name specification the palette-name you have specified contains nonalphanumeric characters and/or more than 32 characters. Action check the palette-name and retry the command. Os6821 improper...

  • Page 182

    Oss (operating system software) messages 6-104 xerox docuprint 180 lps message guide os6900 data on page exceeds page size. Check output. There is too much data to fit on the page being imaged. Some data may have been imaged off the page. Action check printed output. If overflow has occurred, recrea...

  • Page 183

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-105 os6920 line exceeded page limit. Line truncated. A new margin has taken effect or a new line was started. Current line length is longer than page size. The excess has been cut off. Action 1. Check the jdl/djde margi...

  • Page 184

    Oss (operating system software) messages 6-106 xerox docuprint 180 lps message guide os6952 imaging error. Possible data off page. Page integrity cannot be guaranteed, therefore page will not be printed. An imaging error has occurred on the current page. Action 1. Press the key to continue printing....

  • Page 185

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-107 os level 7: system problem indicates a problem with a specific job. Run the next job and report the problem to your supervisor. Os7100 pcc or translate table unreadable. The system cannot read the printer carriage c...

  • Page 186

    Oss (operating system software) messages 6-108 xerox docuprint 180 lps message guide os7210 input cannot recover —not enough dynamic memory. Automatic job recovery has been attempted after a software failure caused a system rollover. The system is unable to recover data because insufficient dynamic ...

  • Page 187

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-109 os7401 jde/jdl require online mode. Enter “online” the jde or jdl specified requires the system to be online. Action 1. Restart the job with a different jde/jdl id. Or enter the online command to place the system on...

  • Page 188

    Oss (operating system software) messages 6-110 xerox docuprint 180 lps message guide os7500 insufficient memory for jde. Os7510 insufficient memory for jde tables. Os7520 insufficient memory for vfu tables. Os7530 insufficient memory for cme tables. Os7550 insufficient memory for input buffers. The ...

  • Page 189

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-111 os7830 insufficient dynamic memory for fountainheads. Not enough dynamic memory remains to process the font index option; or multiple djde “jde =” or “jdl =” commands were incorrectly invoked. The job will abort. Ac...

  • Page 190

    Oss (operating system software) messages 6-112 xerox docuprint 180 lps message guide os7950 unable to open print file... Enter “reset” then rea. The print file on the system disk was left in such state that it cannot be opened. The job will not print. Action 1. Enter the reset command. 2. Enter the ...

  • Page 191

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-113 os level 8: probable severe software error warns of probable severe software errors. Os8010 input found nothing to print. The file just processed by input has generated no printed output. The file is a null file (co...

  • Page 192

    Oss (operating system software) messages 6-114 xerox docuprint 180 lps message guide os8051 ipd communication; initialization failure. An unexpected error was detected when attempting to open communications with input and the job was then aborted. Action 1. Reset the system before entering the next ...

  • Page 193

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-115 os8100 requested task already active - reboot the system. The task requested is still active improperly, possibly due to improper job recovery after a software failure. Action press the boot button and enter b to fo...

  • Page 194

    Oss (operating system software) messages 6-116 xerox docuprint 180 lps message guide os8410 byte aligned disk i/o request... Input aborting. The input task issued a disk input/output request on a byte boundary rather than a correct word boundary. The job is aborting. Action 1. Restart the job. This ...

  • Page 195

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-117 os8555 drive xxx not useable: wrong disk id. The indicated disk drive cannot be used because it was moved from another system and was not formatted for this one. Action reformat the disk. (refer to your xerox docupr...

  • Page 196

    Oss (operating system software) messages 6-118 xerox docuprint 180 lps message guide os8704 output task does not match ig/printer type. Sysgen was performed with a configuration that does not match the current configuration. Action resysgen with the proper configuration if authorized to do so (refer...

  • Page 197

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-119 os8855 invalid form file header. The input task is unable to read a form file header due to software or disk/cpu problems. The job will abort. Action 1. Recompile the form with the correct file header. (refer to you...

  • Page 198

    Oss (operating system software) messages 6-120 xerox docuprint 180 lps message guide os8980 unable to initiate input task. The requested input task cannot be found or read from disk. Action 1. Enter the reset command. 2. Restart the job. 3. If the message reappears, reboot the system by pressing the...

  • Page 199

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-121 os level 9: probable severe hardware error warns of probable hardware errors. Os9050 unexpected error detected by rip. Enter: a rip error has occurred. You will be prompted to continue or abort. Action enter continu...

  • Page 200

    Oss (operating system software) messages 6-122 xerox docuprint 180 lps message guide os9103 disk error with ipd message file, etnmsg.Sys. The system detected a read error the interpress message file and could not generate the job error summary; the error summary is stopped at this point. Action 1. I...

  • Page 201

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-123 os9210 parity error on input medium. A parity error has been discovered in the magnetic tape input buffer in cpu memory. (the error was not reported by the magnetic tape drive itself.) or the message also appears if...

  • Page 202

    Oss (operating system software) messages 6-124 xerox docuprint 180 lps message guide os9310 output disk error. Page won‘t be printed. Abort o or the page cannot be printed because print data cannot be read off disk due to a system disk error. (this message is followed by message os2000.) the printer...

  • Page 203

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-125 os9369 nvm failed to clear. The printer is unable to clear and reset the error count (non-volatile memory) used by the xerox service representative. Printing continues. Action contact your systems specialist or xero...

  • Page 204

    Oss (operating system software) messages 6-126 xerox docuprint 180 lps message guide os9460 disk error - ocs. Call for service. Os9500 bad block on disk - input. Call for service. Os9530 disk error - input. Call for service. Os9531 disk error - processing djde‘s. Os9532 disk write error - rtext file...

  • Page 205

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-127 os9800 hardware error/disk - input. Call for service. A fatal system disk error has occurred in input. Action 1. Restart the job. 2. If the failure recurs, contact your systems specialist or xerox customer service. ...

  • Page 206

    Oss (operating system software) messages 6-128 xerox docuprint 180 lps message guide os9989 unable to acquire memory for device drivers: memory problems are sufficiently severe that there is not enough memory to load hardware peripheral handler(s). Action 1. Reboot the system by pressing the boot bu...

  • Page 207

    Oss (operating system software) messages xerox docuprint 180 lps message guide 6-129 os9994 unable to find system tasks. The disk files required for proper operation of the system appear to have been destroyed on the system disk. Action 1. Reboot the system by pressing the boot button, then entering...

  • Page 208

    Oss (operating system software) messages 6-130 xerox docuprint 180 lps message guide os9998 unable to acquire memory for initialization. Memory problems are sufficiently severe that there is not enough memory to initialize the system at startup. Action 1. Reboot the system by pressing the boot butto...

  • Page 209: Pdl (Job Source Library

    Xerox docuprint 180 lps message guide 7-1 7. 7 pdl (job source library compilation) messages these messages may appear while a job source library is being compiled using print description language (pdl). Pdl messages are assigned to levels 0-9, depending on the severity of the condition being report...

  • Page 210

    Pdl (job source library compilation) messages 7-2 xerox docuprint 180 lps message guide pd0250 replace denied by operator. The operator has specified noreplace in the pdl invocation line. No action is needed. Action none. Pd0300 nothing to print, pdl terminated. When pdl encounters a problem before ...

  • Page 211

    Pdl (job source library compilation) messages xerox docuprint 180 lps message guide 7-3 pd1110 jsl contains unsupported features. There are features invoked in the jsl which are not currently supported by the xerox docuprint 180 lps. Action none. Pd1200 use the ifu ipfnts command to compile ipfnts. ...

  • Page 212

    Pdl (job source library compilation) messages 7-4 xerox docuprint 180 lps message guide pd7050 tape record size error. The record size entered in jsl is incorrect for the tape format. Action enter the correct record size pd7200 pdl internal table overflow. Not enough dynamic memory remains for jsl. ...

  • Page 213

    Pdl (job source library compilation) messages xerox docuprint 180 lps message guide 7-5 pd8550 i/o error, processing sef mapping file. An i/o error occurred while processing the short edge feed font mapping file. Action recompile the jsl that generated the requested mapping file and retry the operat...

  • Page 214

    Pdl (job source library compilation) messages 7-6 xerox docuprint 180 lps message guide pd9510 pdl restart error opening save file. At termination of pdl processing, an attempt to save the file was unsuccessful due to a system disk error. Action 1. Recompile jdl and retry 2. If the problem continues...

  • Page 215: Pg (Purge Command)

    Xerox docuprint 180 lps message guide 8-1 8. 8 pg (purge command) messages these messages may appear during process of purging disk or print file. Refer to your xerox docuprint 180 lps operations reference for detailed information about the purge command. Pg0100 processing the entire disk. The purge...

  • Page 216

    Pg (purge command) messages 8-2 xerox docuprint 180 lps message guide pg0217 purging hip spool file. The purge command is removing unwanted data from the hip spool file. Action none pg0300 processing the entire disk except the print file. The purge f command was entered. The system is clearing all u...

  • Page 217: Pr (Hardcopy Graphics

    Xerox docuprint 180 lps message guide 9-1 9. 9 pr (hardcopy graphics printing command) messages these messages may appear during the hardcopy process (printing copy of graphic .Img files with comprehensive descriptor page). Refer to your xerox docuprint 180 lps operations reference for information a...

  • Page 218

    Pr (hardcopy graphics printing command) messages 9-2 xerox docuprint 180 lps message guide pr2600 not enough space on disk to hardcopy. The selected file cannot be hardcopied because the print file is not large enough to hold it action 1. Use the reallocate command to enlarge the print file. (refer ...

  • Page 219

    Pr (hardcopy graphics printing command) messages xerox docuprint 180 lps message guide 9-3 pr2985 security violation. The requested file has been secured by the abnormal security = yes command. An attempt was made to access it at a wrong logon level. Action to access the file, obtain the correct pas...

  • Page 220

    Pr (hardcopy graphics printing command) messages 9-4 xerox docuprint 180 lps message guide.

  • Page 221: 10.

    Xerox docuprint 180 lps message guide 10-1 10. 10 psc (printer subsystem controller command) messages the psc command enables the selectable download of a printer controller software. (refer to your xerox docuprint 180 lps operations reference chapter on managing lps resources for additional informa...

  • Page 222

    Psc (printer subsystem controller command) messages 10-2 xerox docuprint 180 lps message guide ps9001 csi download error —csi not loaded. The csi board is not functional. Action contact your systems specialist or the xerox customer service. Ps9002 scsi download failed—executing from rom. The firmwar...

  • Page 223

    Psc (printer subsystem controller command) messages xerox docuprint 180 lps message guide 10-3 ps9960 download error: san nn.Nn this message provides the software analysis code (san) needed by xerox customer service to correct the download error. Action none ps9961 download error: san nn.Nn this mes...

  • Page 224

    Psc (printer subsystem controller command) messages 10-4 xerox docuprint 180 lps message guide.

  • Page 225: 11.

    Xerox docuprint 180 lps message guide 11-1 11. 11 scale command messages the scale command enables scanned graphic images (fonts, forms, and logos) to print at an enlarged or reduced size under certain conditions. Refer to your xerox docuprint 180 lps operations reference chapters on hip-accessed co...

  • Page 226

    Scale command messages 11-2 xerox docuprint 180 lps message guide **cannot open input file: xxxx the requested input file is not found. Action verify the input file name and reenter the command. (refer to your xerox docuprint 180 lps operations reference chapter on managing lps resources for additio...

  • Page 227

    Scale command messages xerox docuprint 180 lps message guide 11-3 or press the key to exit this activity. **error (n.N) generating output file** the system is unable to generate the output file. Action 1. Check the scale command and reenter. 2. If the message reappears, contact your systems speciali...

  • Page 228

    Scale command messages 11-4 xerox docuprint 180 lps message guide **file type in output name must be xxxx the file type in the output name must be from an acceptable font directory. Action reenter the output name using a font from the specified directory. Acceptable file types are fnt, fn6, fr6, lg0...

  • Page 229

    Scale command messages xerox docuprint 180 lps message guide 11-5 **font scaling resulted in size mismatch** scaling caused a mismatch between the estimated and actual bitmap sizes. Action contact your systems specialist or xerox customer support. **font xxxx is not alpha-numeric** the font or logo ...

  • Page 230

    Scale command messages 11-6 xerox docuprint 180 lps message guide **more than one white space character not supported** the requested form consists of a format which cannot be scaled to 600 spi correctly. Action none **no dynamic memory** there is no dynamic memory available. Action contact your sys...

  • Page 231

    Scale command messages xerox docuprint 180 lps message guide 11-7 **run font through fix on cd/ig version 2 or higher** the font must be modified through the fix command before scaling. Action 1. Enter the appropriate fix command. (refer to your xerox docuprint 180 lps operations reference chapter o...

  • Page 232

    Scale command messages 11-8 xerox docuprint 180 lps message guide scaling header. The font or logo header is being scaled. Action none scaling logo: xxxx the requested logo is being scaled. Action none. Scaling tl number: n text line number n is being scaled. Action none scaling tl/dl nn the identif...

  • Page 233: 12.

    Xerox docuprint 180 lps message guide 12-1 12. 12 sfs (status file services command) messages the following messages refer to the status file services (sfs) command, which creates, clears, displays, prints, and stores status file information. Refer to your xerox docuprint 180 lps operations referenc...

  • Page 234

    Sfs (status file services command) messages 12-2 xerox docuprint 180 lps message guide sf2100 invalid field for ‘byte counter’ sf2100 invalid terminating character sf2102 invalid field for ‘record length’ sf2103 invalid field for ‘tape density’ sf2104 invalid field for ‘size’ sf2105 invalid delimite...

  • Page 235

    Sfs (status file services command) messages xerox docuprint 180 lps message guide 12-3 sf4500 cannot write on tape. Check tape and try again. The write enable ring is missing from magnetic tape, magnetic tape is not loaded correctly, or the magnetic tape drive is not online to the printer. Action pl...

  • Page 236

    Sfs (status file services command) messages 12-4 xerox docuprint 180 lps message guide sf6050 a - cannot open file. Abort the command file needed for the user-created form cannot be accessed due to system disk error. (“a -” indicates sfs is aborting.) action 1. Retry compiling the form. The message ...

  • Page 237

    Sfs (status file services command) messages xerox docuprint 180 lps message guide 12-5 sf6070 e - value for ‘width’ unspecified or exceeds limit. The value entered for the width statement for a user-created form is larger than that permitted for the column width; or no width statement was entered. T...

  • Page 238

    Sfs (status file services command) messages 12-6 xerox docuprint 180 lps message guide.

  • Page 239: 13.

    Xerox docuprint 180 lps message guide 13-1 13. 13 system verification error messages these messages appear on the system controller display if problems are detected during the verification self-tests that the system runs at start-up after the date and time display is entered or disabled. These messa...

  • Page 240

    System verification error messages 13-2 xerox docuprint 180 lps message guide fcg starting. Version x fcg is starting with the parameters (or version) indicated. Action 1. Retry the fcg command. 2. If the message reappears, look for other system or printer messages to explain the condition. 3. If no...

  • Page 241

    System verification error messages xerox docuprint 180 lps message guide 13-3 no font memory available. All banks of font memory appear not to be functional or to have suffered data loss. Action none. No graphics memory. All banks of graphics memory appear to be missing or have failed testing. Actio...

  • Page 242

    System verification error messages 13-4 xerox docuprint 180 lps message guide.

  • Page 243: 14.

    Xerox docuprint 180 lps message guide 14-1 14. 14 summary sheet error messages your xerox docuprint 180 lps communicates interpress error messages to you on the system controller display and on summary sheets that accompany your printed output. Summary sheets are placed at the end of printed jobs. E...

  • Page 244

    Summary sheet error messages 14-2 xerox docuprint 180 lps message guide explanations are listed in the lefthand column in bold letters. Meanings and appropriate actions to take, if any, are provided in the righthand column. For further information about interpress, refer to your xerox docuprint 180 ...

  • Page 245

    Summary sheet error messages xerox docuprint 180 lps message guide 14-3 form file not found: “filetype>filename.” when processing an sif, no file with the name filename.Filetype was locally available to the xerox docuprint 180 lps. Action load the form on the lps or change the form reference in the ...

  • Page 246

    Summary sheet error messages 14-4 xerox docuprint 180 lps message guide appearance warning messages appearance warning: appearance warning: image off paper on page n at , [inches];, {cm]. Lines(s) not printed. One or more lines of text extended beyond the clipping region and, as a result, the lines ...

  • Page 247

    Summary sheet error messages xerox docuprint 180 lps message guide 14-5 font “interpressfontname” substituted for "interpressfontname." the default font family has been substituted for the requested font family. Action none. Further “...Substituting point size dd ...” messages suppressed. Many ...Su...

  • Page 248

    Summary sheet error messages 14-6 xerox docuprint 180 lps message guide master error (page n): problem with insert file; invalid file folder: “file-type”. An sif requested a file folder (type) not accessible from an interpress master. The valid folders are frm, img, lgo, lib, spl, and xcs. Action no...

  • Page 249

    Summary sheet error messages xerox docuprint 180 lps message guide 14-7 specified color not implemented. The colors available in the publication set cannot be used for text or pixel arrays if the raster image processor (rip) option is not supported. Action none. String off paper on page n at , [inch...

  • Page 250

    Summary sheet error messages 14-8 xerox docuprint 180 lps message guide fatal error messages fatal error: incorrect size for jobaccount name; the size must be between 1 and 31 characters inclusive. The jobaccount name taken from the document exceeded the length of the allowable range. Action reduce ...

  • Page 251

    Summary sheet error messages xerox docuprint 180 lps message guide 14-9 insufficient disk space for image file when reading an image from raster image processor (rip), a full system disk condition occurred. Action actionpurge unnecessary files from the lps and compress the system disks to free conti...

  • Page 252

    Summary sheet error messages 14-10 xerox docuprint 180 lps message guide operator requested job abort. The abort i command terminated document processing at the end of the current page. Action none. Page too complicated; too many fonts+forms+operators text+graphics. The page is too complicated to pr...

  • Page 253

    Summary sheet error messages xerox docuprint 180 lps message guide 14-11 unexpected disk error creating temporary file filetype>filename. An error was found while writing to the system disk. The system disk has one or more bad sectors which are not in the bad block file. Action 1. Resend the documen...

  • Page 254

    Summary sheet error messages 14-12 xerox docuprint 180 lps message guide informational messages informational messages character nb is not in font “filetype>localfontname”, set nb. This message identifies character references beyond the last character, highest character code, in an lps font and foll...

  • Page 255

    Summary sheet error messages xerox docuprint 180 lps message guide 14-13 document printing terminated due to error(s). The job was ended because of a previous error on the summary sheet. This message is added to the actual error message. Action none. Error sheet only; document not printed due to err...

  • Page 256

    Summary sheet error messages 14-14 xerox docuprint 180 lps message guide substituting n point (rotated n degrees) characters. The desired point size was not satisfied and the next smaller (or next larger if there is no next smaller) point size is substituted. This message follows the ... Font proble...

  • Page 257

    Summary sheet error messages xerox docuprint 180 lps message guide 14-15 master error messages master error (page n): disk problem with insert file: “filetype>filename.” an error was found while reading the system disk. The system disk has one or more bad sectors which are not in the bad block file....

  • Page 258

    Summary sheet error messages 14-16 xerox docuprint 180 lps message guide font problem; font “interpressfontname” unknown. The default family name, as specified in the font profile or ipfnts.Jsl, does not have a mapping to lps fonts defined for the identified family. Action key in ifu add for the des...

  • Page 259

    Summary sheet error messages xerox docuprint 180 lps message guide 14-17 form problem; form/job paper size mismatch: “filetype>localformname.” the form file identified was compiled with a paper size which does not match page n’s paper size. Action 1. Change the form referenced in the document. Or re...

  • Page 260

    Summary sheet error messages 14-18 xerox docuprint 180 lps message guide master not well-formed; bad document header. The interpress header, “interpress/xerox/n.0...” was not found in a file that required one. The file is either the interpress master or an sif. A sif problem is preceded by the error...

  • Page 261

    Summary sheet error messages xerox docuprint 180 lps message guide 14-19 parse failure; illegal operator ordering; nested correct bodies not allowed. The interpress master has a correct body beginning before the current body is complete. Action none. Parse failure; invalid parsing continued after en...

  • Page 262

    Summary sheet error messages 14-20 xerox docuprint 180 lps message guide parse failure; unrecognized operator: when processing a form, a form file with an invalid format was found. Action recompile the form’s fsl. Problem with insert file; invalid file folder: “filetype.” an sif requested a file fol...

  • Page 263

    Summary sheet error messages xerox docuprint 180 lps message guide 14-21 master warning messages master warning (page n): processing nested too deep. Nesting of interpress bodies exceeds the program stack space of the decomposer. Action none. Too many “page warnings” on this page. Too many page warn...

  • Page 264

    Summary sheet error messages 14-22 xerox docuprint 180 lps message guide system problem messages system problem: accounting initialization failure. A problem processing the accounting information was found. Action none. Can not record errors; “sys>rtxfil” missing resysgen. The file that stores error...

  • Page 265

    Summary sheet error messages xerox docuprint 180 lps message guide 14-23 disk error recording errors; all messages lost. An error was found while reading the system disk. The system disk has one or more bad sectors which are not included in the bad block file. Action 1. Rename rtxfil.Sys to a well-k...

  • Page 266

    Summary sheet error messages 14-24 xerox docuprint 180 lps message guide unrecoverable disk error reading “sys>ipfnts”; recompile “jsl>ipfnts.” an error was found while reading the system disk. The system disk contains one or more bad sectors that are not in the bad block file. Action 1. Rename ipfn...

  • Page 267: 15.

    Xerox docuprint 180 lps message guide 15-1 15. 15 xerox docuprint 180 lps additional messages these messages may appear on your xerox docuprint 180 lps pc user interface (pc ui). How the messages are organized messages that appear on your screen with numbers in front of them are listed in the first ...

  • Page 268

    Xerox docuprint 180 lps additional messages 15-2 xerox docuprint 180 lps message guide general action to take as a general rule, when an error message is displayed in a message window on your xerox docuprint 180 lps pc user interface, the recommended actions are as follows: action • follow any speci...

  • Page 269

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-3 numbered xerox docuprint 180 lps messages messages 7 through 36 messages 7 through 36 appear when serious user interface software problems occur. For all of these messages, call for xerox service. Messages 41 and ...

  • Page 270

    Xerox docuprint 180 lps additional messages 15-4 xerox docuprint 180 lps message guide 544 signal expected but not received the pc user interface was expecting to receive signal data. Action select the ok header button to retry the process. If the problem persists, call xerox customer service. 545 p...

  • Page 271

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-5 552 can’t post sm_comm message posting of the sm_comm message to the application’s queue failed. The communication with the system controller has not been initiated. Action 1. Ensure no other microsoft windows app...

  • Page 272

    Xerox docuprint 180 lps additional messages 15-6 xerox docuprint 180 lps message guide 559 data set ready timeout the data set ready timeout has been exceeded. Action select the ok header button to retry the process. If the problem persists, call xerox customer service. 560 frame error detected the ...

  • Page 273

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-7 567 parity error while receiving the user interface does not use this feature of rs232. Action select the ok header button to retry the process. If the problem persists, call xerox customer service. 568 transmit q...

  • Page 274

    Xerox docuprint 180 lps additional messages 15-8 xerox docuprint 180 lps message guide 574 invalid custom signal data the format of this system controller signal is invalid. Action select the ok header button to retry the process. If the problem persists, call xerox customer service. Messages 1538 t...

  • Page 275

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-9 1545 invalid mouse speed rate an incorrect mouse speed was specified. Action select the ok header button to retry the process. If the problem persists, call xerox customer service. 1546 missing directory name in c...

  • Page 276

    Xerox docuprint 180 lps additional messages 15-10 xerox docuprint 180 lps message guide 1554 invalid comm device; must be 1 or 2 the parameter value of the “device” statement in the sysui configuration file is invalid. Action select the ok header button to retry the process. If the problem persists,...

  • Page 277

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-11 1561 cannot create ui dirty file; ui cannot run ms-dos cannot create a sysui dirty file. Action select the ok header button to retry the process. If the problem persists, call xerox customer service. 1562 cannot ...

  • Page 278

    Xerox docuprint 180 lps additional messages 15-12 xerox docuprint 180 lps message guide 1568 no record types specified for console log report the parameters of the optional “reptype” statement in the sysui configuration file are missing. Action select the ok header button to retry the process. If th...

  • Page 279

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-13 3539 creation of console log file failed 3540 read console log file header failed 3541 write console log file header failed 3542 reset console log file header failed for message numbers 3539, 3540, 3541, or 3542,...

  • Page 280

    Xerox docuprint 180 lps additional messages 15-14 xerox docuprint 180 lps message guide 3553 console log file wrap failed console log record could not be wrapped on disk due to hardware considerations. Action 1. Check disk drive to ensure that console log disk is inserted in disk drive and that writ...

  • Page 281

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-15 3578 a console log is being formatted for printing formatting of a console log in preparation for printing is currently in progress. Informational message. No action required. Action none. 3579 a console is being...

  • Page 282

    Xerox docuprint 180 lps additional messages 15-16 xerox docuprint 180 lps message guide 4137 through 4145 these messages relate to the loading of the symbol table, which contains object and data variable information for action processing. Select the ok header button to retry the process. Action if t...

  • Page 283

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-17 9041 invalid access request code the calling program has requested an invalid ddb (dialog data base) operation. Action select the ok header button to retry the process. If the problem persists, contact xerox cust...

  • Page 284

    Xerox docuprint 180 lps additional messages 15-18 xerox docuprint 180 lps message guide 9049 not a maintenance file the ddb (dialog data base) data file is being used in the wrong mode. Action select the ok header button to retry the process. If the problem persists, contact xerox customer service. ...

  • Page 285

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-19 9060 no data file on re-open error intermediate ddb (dialog data base) data file not found. The missing file may represent the results of one or more previous steps in the process of the program (mm, cd or tdb). ...

  • Page 286

    Xerox docuprint 180 lps additional messages 15-20 xerox docuprint 180 lps message guide 9537 can’t allocate memory general pc user interface memory allocation failure. Call to microsoft windows globalalloc has (or would have) failed. Action 1. Ensure no other microsoft windows applications are runni...

  • Page 287

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-21 a boundary must be selected for 0 reams. The 0 reams option has been selected in the bin full criteria window. Action select a separation boundary (set, report, or job) in the bin full criteria window to tell the...

  • Page 288

    Xerox docuprint 180 lps additional messages 15-22 xerox docuprint 180 lps message guide attempting completion but no completion phase record exists. Following the end of report printing, the phase manager cannot find a phase record to manage the completion of the audit log. Action if the problem per...

  • Page 289

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-23 aud file mgr extended file not found. Tbd action if the problem persists, call xerox customer service. Aud file mgr file access denied due to read only mode or owner name. Aud file mgr file access denied due to r...

  • Page 290

    Xerox docuprint 180 lps additional messages 15-24 xerox docuprint 180 lps message guide aud file mgr file not found. Tbd action if the problem persists, call xerox customer service. Aud file mgr file not open. Tbd action if the problem persists, call xerox customer service. Aud file mgr file table f...

  • Page 291

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-25 aud file mgr key buffer too short for requested index path. Tbd action if the problem persists, call xerox customer service. Aud file mgr key length invalid. Tbd action if the problem persists, call xerox custome...

  • Page 292

    Xerox docuprint 180 lps additional messages 15-26 xerox docuprint 180 lps message guide aud file mgr pre-image i/o error. Tbd action if the problem persists, call xerox customer service. Aud file mgr pre-image open error. Tbd action if the problem persists, call xerox customer service. Aud file mgr ...

  • Page 293

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-27 audit log complete. The current report has completed the audit log. Action none. Audit log delete complete. A request to delete a log or logs has completed. Action none. Audit log disk approaching full. The thres...

  • Page 294

    Xerox docuprint 180 lps additional messages 15-28 xerox docuprint 180 lps message guide audit logging state notification. The auditor has changed state by either entering or leaving the active auditing state. Action none. Audit report format already in progress. The audit report formatter is already...

  • Page 295

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-29 btext signal text invalid response a btext keyword parameter contains invalid data, for example an incorrectly specified date. Action check jsl or djde in job stream to ensure that all btext keywords and paramete...

  • Page 296

    Xerox docuprint 180 lps additional messages 15-30 xerox docuprint 180 lps message guide cannot allocate memory for report field list. Insufficient system memory exists to parse the fields requested to list audit logs. Action if the problem persists, call xerox customer service. Cannot allocate memor...

  • Page 297

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-31 cannot open master directory file for crash recovery. The record manager is unable to open the master directory file to support crash recovery. Action if the problem persists, call xerox customer service. Cannot ...

  • Page 298

    Xerox docuprint 180 lps additional messages 15-32 xerox docuprint 180 lps message guide command sequence error, record number not equal to last +1. One or more of the report definition commands are out of order. Action if the problem persists, call xerox customer service. Communication with the prin...

  • Page 299

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-33 duplicate aud file mgr key not allowed. Tbd action if the problem persists, call xerox customer service. Duplicate key value updating master directory file for completion copy. The master directory record already...

  • Page 300

    Xerox docuprint 180 lps additional messages 15-34 xerox docuprint 180 lps message guide error changing directory tbd action if the problem persists, call xerox customer service. Error closing report format output file. The record manager is unable to close the output file that contains the formatted...

  • Page 301

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-35 excessive length for btext pra page reconciliation parameter. The page reconciliation parameter contains too many characters. Action check the jsl or djde in the job stream to ensure that all btext pra keywords a...

  • Page 302

    Xerox docuprint 180 lps additional messages 15-36 xerox docuprint 180 lps message guide failure to create audit formatting window. This could occur during pc ui session startup. Windows has failed to allow the auditor feature to create a window. Action if the problem persists, call xerox customer se...

  • Page 303

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-37 failure to open aud file mgr in-process log file. The auditor is unable to open the in-process audit log. Audit logging will not take place. Action if the problem persists, call xerox customer service. Failure to...

  • Page 304

    Xerox docuprint 180 lps additional messages 15-38 xerox docuprint 180 lps message guide fcg exiting: invalid profile encountered. The following message is displayed if the information necessary for the fcg show command is not present on the system. Action none. Fcg exiting: invalid profile—missing s...

  • Page 305

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-39 file cannot be accessed . . . . The file is too large for the pc editor to process. Action if the file is an ess file, use edi in the message window. File could not be emptied or deleted. Ensure that the filename...

  • Page 306

    Xerox docuprint 180 lps additional messages 15-40 xerox docuprint 180 lps message guide filter file does not exist. The file to filter pc ui messages and / or the file to filter ess messages for audit logging is missing. Audit logging in not prevented, but no operational messages will be logged in a...

  • Page 307

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-41 incorrect field offset for extended get/step operation. Tbd action if the problem persists, call xerox customer service. Initializing client-layer protocol the system controller has established low-level communic...

  • Page 308

    Xerox docuprint 180 lps additional messages 15-42 xerox docuprint 180 lps message guide insufficient space on target device. The target of an audit log save operation has insufficient space to contain the entire log. Action delete files to make space on the target device. If this fails to provide en...

  • Page 309

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-43 invalid btreive alternate collating sequence definition. Tbd action if the problem persists, call xerox customer service. Invalid buffer for extended insert operation. Tbd action if the problem persists, call xer...

  • Page 310

    Xerox docuprint 180 lps additional messages 15-44 xerox docuprint 180 lps message guide invalid parameter - dec command. A dec command has an invalid parameter. The report definition file may be corrupt. Action if the problem persists, call xerox customer service. Invalid parameter - first command. ...

  • Page 311

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-45 invalid parameter - justifyx command. A justifyx command has an invalid parameter. The report definition file may be corrupt. Action if the problem persists, call xerox customer service. Invalid parameter - lwid ...

  • Page 312

    Xerox docuprint 180 lps additional messages 15-46 xerox docuprint 180 lps message guide invalid response for btext dar default reporting parameter. The default reporting parameter is incorrectly specified. Action check jsl or djde in the job stream to ensure that all btext dar keywords and parameter...

  • Page 313

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-47 invalid response for btext rsq sequence check enablement parameter. The sequence check parameter is incorrectly specified. Action check jsl or djde in the job stream to ensure that all btext rsq keywords and para...

  • Page 314

    Xerox docuprint 180 lps additional messages 15-48 xerox docuprint 180 lps message guide log xxx is empty. Informational message only. Action none. Log xxx is in use and cannot be deleted. The requested console log file is in use. Action if you wish to empty the log file, select the file name and sel...

  • Page 315

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-49 missing btext keyword parameter value. A btext keyword that requires a parameter has none. Action check jsl or djde in the job stream to ensure that all btext keywords and parameters are correct. Missing report d...

  • Page 316

    Xerox docuprint 180 lps additional messages 15-50 xerox docuprint 180 lps message guide note xxx does not exist. The requested note name does not exist. Action try entering another note name. Note xxx is unreadable and cannot be (deleted/displayed/ saved). Call for service. The requested note cannot...

  • Page 317

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-51 printer is ready. Informational message. The xerox docuprint 180 lps is communicating normally and is ready to print. There are no existing faults or hints. Action none. Printer is reinitializing. Informational m...

  • Page 318

    Xerox docuprint 180 lps additional messages 15-52 xerox docuprint 180 lps message guide sheet delivery signal but no output phase record exists. A sheet delivery signal has been received but no output phase exists for the report. Auditor has not recorded start of output. Action if the problem persis...

  • Page 319

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-53 the current log is empty. Information message only. You tried to display an empty current console log. Action none. The current log is in use and cannot be emptied. The current console log is in use. Action none....

  • Page 320

    Xerox docuprint 180 lps additional messages 15-54 xerox docuprint 180 lps message guide there are no hints (*) this message is displayed with the “printer is ready” message. The lps is ready to print the current job. There may be faults in the system (such as a bin or tray unavailable) that do not a...

  • Page 321

    Xerox docuprint 180 lps additional messages xerox docuprint 180 lps message guide 15-55 trying to lock a record locked by another application. Tbd action finish and jobs that are currently printing and then reboot the system. Unable to read the file. Try again. The system was unable to read the dos ...

  • Page 322

    Xerox docuprint 180 lps additional messages 15-56 xerox docuprint 180 lps message guide.

  • Page 323: Xerox Support Services

    Xerox docuprint 180 lps message guide a-1 a. A xerox support services xerox support services are there to help you if your laser printing system should develop a severe hardware, software, or applications problem. If a problem continues after you have tried all remedial actions suggested in this gui...

  • Page 324

    Xerox support services a-2 xerox docuprint 180 lps message guide xerox customer service support center the xerox customer service support center is available to address your software- or hardware-related problems, such as continuous paper jams or poor print quality, if the corrective action(s) descr...

  • Page 325

    Xerox support services xerox docuprint 180 lps message guide a-3 xerox font center the font center can send you samples and catalogs of the fonts available for your xerox docuprint 180 lps, and can take orders for licensed and custom fonts. Call the xerox font center for information or to place an o...

  • Page 326

    Xerox support services a-4 xerox docuprint 180 lps message guide.

  • Page 327: Glossary

    Xerox docuprint 180 lps message guide glossary-1 glossary a3 paper size measuring 297 by 420 mm. A4 paper size measuring 210 by 297 mm. Abort to terminate the printing of a job or execution of a program before it completes. Algorithm computational procedure that can be repeated any number of times. ...

  • Page 328

    Glossary glossary-2 xerox docuprint 180 lps message guide auxiliary menu menu that contains options not displayed in a window. The symbol for an auxiliary menu is a box containing three horizontal lines. B4 paper size measuring 250 by 353 mm. Background job low-priority job, usually batched, that is...

  • Page 329

    Glossary xerox docuprint 180 lps message guide glossary-3 bit map visual representation of graphic images in which a bit defines a picture element (pixel); for example, if a bit is 1, the corresponding pixel is printed. Bit mapped display image generated bit by bit for each point or dot. A software-...

  • Page 330

    Glossary glossary-4 xerox docuprint 180 lps message guide character single printable letter (a-z), numeral (0-9), symbol (& % #), or punctuation mark (, . ! ?) used to represent data. Characters can also be nonprinting, such as space, tab, or carriage return. Character cell digitized space containin...

  • Page 331

    Glossary xerox docuprint 180 lps message guide glossary-5 communication line telecommunication line connecting devices at one location with devices at other locations in order to transmit and receive information. Communication link physical means, such as data link, connecting one location to anothe...

  • Page 332

    Glossary glossary-6 xerox docuprint 180 lps message guide copy-sensitive term used to indicate jobs in which multiple copies of a report will contain different data, as with paychecks and banking statements. Cpi characters per inch. Designates the number of characters per inch for a particular typef...

  • Page 333

    Glossary xerox docuprint 180 lps message guide glossary-7 descender portion of alphabetic character that extends below the baseline. See also ascender, x height. Desktop basic display screen of the pc ui. Device any piece of hardware other than the central processing unit (cpu). Digitize to express ...

  • Page 334

    Glossary glossary-8 xerox docuprint 180 lps message guide elite smallest size standard typewriter type: 12 characters per horizontal inch. See also pica. Embedded blanks blank spaces within a command line. Extended metrics measurements used in interpress to alter the size of fonts, allowing more pre...

  • Page 335

    Glossary xerox docuprint 180 lps message guide glossary-9 form 1. Compiled forms source library (.Fsl) file. 2. Printed or typed document with blank spaces for inserting information. Specific arrangement of lines, text, and graphics stored in a computer under an identifying name. Page of data that, ...

  • Page 336

    Glossary glossary-10 xerox docuprint 180 lps message guide and associated documentation. Hardware is operated by software and firmware. Hcf high-capacity feeder. Feeder tray capable of holding 2500 sheets of 20 pound/75 gsm paper. The high-capacity feeder trays are the primary paper supply for the d...

  • Page 337

    Glossary xerox docuprint 180 lps message guide glossary-11 insert to add text or graphics to a document. Interface device by which two systems connect and communicate with each other. Interpolation series of logical rules implemented in the printer to convert a 300 spi input video stream to a 600 sp...

  • Page 338

    Glossary glossary-12 xerox docuprint 180 lps message guide 2. In programming, a name assigned to a particular instruction or portion of a program as a locational reference (the computer translates the label into an address). Landscape page orientation orientation of print lines or top of an illustra...

  • Page 339

    Glossary xerox docuprint 180 lps message guide glossary-13 load to enter data into storage or working registers. Location place in which data can be stored. Log collection of messages or message segments placed on an auxiliary storage device for accounting or data collection purposes. Logical page i...

  • Page 340

    Glossary glossary-14 xerox docuprint 180 lps message guide medium object or material on which data is stored, for example, magnetic tape or floppy disk. Memory space in a device where information is kept, or the ability of a device to keep information until needed. Menu list of available functions, ...

  • Page 341

    Glossary xerox docuprint 180 lps message guide glossary-15 offline devices not under the active control of a central processing unit. For example, a computer makes output to a magnetic tape. The tape is then used by an offline printing system to produce printed data. Offline operations are much slow...

  • Page 342

    Glossary glossary-16 xerox docuprint 180 lps message guide override to take precedence or priority over, to overrule. Overstrike to print characters over each other. Page 1. In computer programming, a block of instruction, data, or both that can be located in main or auxiliary storage. 2. In word pr...

  • Page 343

    Glossary xerox docuprint 180 lps message guide glossary-17 point size height of character set from the top of its ascenders to the bottom of its descenders in units (points). Point size does not always include leading. Portrait page orientation orientation of print lines or the top of an illustratio...

  • Page 344

    Glossary glossary-18 xerox docuprint 180 lps message guide ram random access memory. Storage that allows data, such as documents, to be stored and retrieved directly by address location without reading through any other data. Data binary data, usually consisting of dots arranged in scan lines, accor...

  • Page 345

    Glossary xerox docuprint 180 lps message guide glossary-19 secondary storage form of storage external to a system, such as magnetic tapes or floppy disks. Security 1. Procedure for limiting access to the system resources, programs, or files, to authorized personnel. 2. Protecting programs and files ...

  • Page 346

    Glossary glossary-20 xerox docuprint 180 lps message guide spooling process of releasing data from main memory and storing it temporarily until a peripheral device is ready to accept it, for example storing text before sending it to a printer. Spot unit of measurement representing a fraction of an i...

  • Page 347

    Glossary xerox docuprint 180 lps message guide glossary-21 system file master software program that keeps all components working together. System generation process whereby the system is made ready to operate. Typically involves selecting the operative parameters and activating the relevant software...

  • Page 348

    Glossary glossary-22 xerox docuprint 180 lps message guide testing 1. Process of running a program for the express purpose of discovering any errors it may contain. 2. For computer-oriented systems, the process of verifying a system’s ability to meet performance objectives in a simulated environment...

  • Page 349

    Glossary xerox docuprint 180 lps message guide glossary-23 ucs universal character set. Printer feature that permits the use of a variety of character upload to copy files from a remote peripheral device to a host. Lps files are not copied to the host because one of the lps functions is to store fil...

  • Page 350

    Glossary glossary-24 xerox docuprint 180 lps message guide xdot unit of measurement representing a fraction of an inch. It may also be referred to as a picture element (pixel) or spot, for example, 1/600 spots per inch (spi). Xerographic engine component of a printer that develops an image, transfer...

  • Page 351

    Glossary xerox docuprint 180 lps message guide glossary-25 cr carriage return dce data communications equipment ddcmp digital data communication message protocol dec digital equipment corporation dfa document feeding and finishing architecture djde dynamic job descriptor entry dmr data mode ready (d...

  • Page 352

    Glossary glossary-26 xerox docuprint 180 lps message guide ffm font file management fis font interchange standard fms file management subsystem fps formatting print service fsl forms source library fst font specification table gcr group code recording gsm grams per square meter hcf high-capacity fee...

  • Page 353

    Glossary xerox docuprint 180 lps message guide glossary-27 ipm interpress mapping ips inches per second jcb job control block jcl job control language jde job descriptor entry jdl job descriptor library jid job identifier jsl job source library lan local area network laser light amplification by sti...

  • Page 354

    Glossary glossary-28 xerox docuprint 180 lps message guide oss operating system software pc personal computer pcc printer carriage control pc ui personal computer user interface pdl print description language pe phase encoded ppm pages per minute pqa print quality adjustment prom programmable read-o...

  • Page 355

    Glossary xerox docuprint 180 lps message guide glossary-29 sna system network architecture spi spots per inch sst system software tape sysgen system generation tl/dl text line/display list tof top of form tpi tracks per inch tpj test pattern job txc total xerographic convergence ucs universal charac...

  • Page 356

    Glossary glossary-30 xerox docuprint 180 lps message guide xpaf, xpf xerox printer access facility xpmf-vms xerox print management facility - vms version xppi xerox pen plotter interface xps xerox publishing system.