- DL manuals
- NEC
- Voicemail
- Univerge SV8100
- Features And Specifications Manual
NEC Univerge SV8100 Features And Specifications Manual - Loop Keys
UNIVERGE SV8100
Issue 11.0
Loop Keys
2 - 979
Loop Keys
Description
Loop Keys are uniquely programmed function keys that simplify placing and answering trunk calls.
There are three types of Loop Keys: Incoming Only, Outgoing Only and Both Ways.
Incoming Only Loop Keys
Incoming Only loop keys are for answering trunk calls. An extension can have an incoming loop key for
a specific trunk group (fixed) or a “catch all” loop key for any trunk group (switched). Fixed loop keys
allow an extension user to tell the type of call by the ringing key. Switched loop keys are ideal for an
extension with a large number of feature keys. In addition, switched loop keys are a destination for any
trunk not on a line key or fixed loop key. Without a switched loop key, calls not appearing on a line key or
fixed loop key will ring only the CALL key. Incoming Only loop keys also receive Transferred trunk calls.
Outgoing Only Loop Keys
Outgoing Only loop keys are for placing trunk calls. An extension can have outgoing loop keys for a
specific trunk group or for ARS access. When a user presses the loop key, they get dial tone from the
first available trunk in the group (or from ARS if programmed). Outgoing Only loop keys help ensure that
an extension will always have a key available for placing calls.
Both Ways Loop Keys
Both Ways loop keys combine the functions of both Incoming Only and Outgoing Only loop keys. Both
Ways loop keys work well for extension users that handle a moderate amount of calls and don’t separate
keys for incoming and outgoing calls. Both Ways loop keys also receive Transferred trunk calls. An
extension can have many loop keys - of any type. You can program an operator, for example, with four
loop keys for incoming calls and four for outgoing calls. Once a loop key call is set up, the user can
handle it like any other trunk call. For example, the user can place the call on Hold, Transfer it to a
co-worker or send it to a Park Orbit. An incoming call will ring the first available loop key, beginning with
the lowest numbered key. If keys 1-3 are loop keys, for example, the first incoming call rings key 1. If key
1 is busy, the next call rings key 2. If keys 1 and 2 are busy, the next call rings key 3. If all three keys are
busy, additional incoming calls queue for the first available key. The terminal display will show “WAITING
- LOOP KEY” if the user presses a loop key when there are additional calls waiting.
Enhancements
This feature added with Version 4000.
Summary of Univerge SV8100
Page 1
Notice note that when converting this document from its original format to a .Pdf file, some minor font and format changes may occur. When viewing and printing this document, we cannot guarantee that your specific pc or printer will support all of the fonts or graphics. Therefore, when you view the ...
Page 3
Features and specifications manual int-2067 (univ) issue 11.0 (version 8000) ®.
Page 5
Nec corporation of america reserves the right to change the specifications, functions, or features at any time without notice. Nec corporation of america has prepared this document for use by its employees and customers. The information contained herein is the property of nec corporation of americaa...
Page 7: Preface
Preface before reading this manual this manual provides detailed information for each of the system’s features. If you are not familiar with the features, the table of contents provides a list of the features and where to find the feature within the manual. G eneral i nformation congratulations! You...
Page 8
Univerge sv8100 programming manual this manual provides instructions for programming the univerge sv8100 system using a multiline terminal or pc..
Page 9: Chapter 1
Features and specifications manual i ___________________________________________________________________________________ ___________________________________________________________________________________ table of contents chapter 1 introduction section 1 general information ...........................
Page 10
___________________________________________________________________________________ ii table of contents ___________________________________________________________________________________ issue 11.0 univerge sv8100 barge-in...............................................................................
Page 11
Univerge sv8100 issue 11.0 features and specifications manual iii ___________________________________________________________________________________ ___________________________________________________________________________________ cordless telephone connection .......................................
Page 12
___________________________________________________________________________________ iv table of contents ___________________________________________________________________________________ issue 11.0 univerge sv8100 general purpose relay .................................................................
Page 13
Univerge sv8100 issue 11.0 features and specifications manual v ___________________________________________________________________________________ ___________________________________________________________________________________ k-ccis – t1 ...........................................................
Page 14
___________________________________________________________________________________ vi table of contents ___________________________________________________________________________________ issue 11.0 univerge sv8100 pc programming.........................................................................
Page 15
Univerge sv8100 issue 11.0 features and specifications manual vii ___________________________________________________________________________________ ___________________________________________________________________________________ speed dial – telephone book..........................................
Page 16
___________________________________________________________________________________ viii table of contents ___________________________________________________________________________________ issue 11.0 univerge sv8100 uniform call distribution (ucd) .....................................................
Page 17: Chapter 3
Univerge sv8100 issue 11.0 features and specifications manual ix ___________________________________________________________________________________ ___________________________________________________________________________________ chapter 3 codes tables section 1 about this chapter ..................
Page 18
___________________________________________________________________________________ x table of contents ___________________________________________________________________________________ issue 11.0 univerge sv8100 this page intentionally left blank.
Page 19
Features and specifications manual xi ___________________________________________________________________________________ ___________________________________________________________________________________ list of figures figure 1-1 sv8100 key assignment example ........................................
Page 20
___________________________________________________________________________________ xii list of figures ___________________________________________________________________________________ issue 11.0 univerge sv8100 figure 2-23 single sv8100 to ipk/ipk ii connection .....................................
Page 21
Univerge sv8100 issue 11.0 features and specifications manual xiii ___________________________________________________________________________________ ___________________________________________________________________________________ figure 2-50 vm8000 inmail user pro login diagram ...................
Page 22
___________________________________________________________________________________ xiv list of figures ___________________________________________________________________________________ issue 11.0 univerge sv8100 this page intentionally left blank.
Page 23
Features and specifications manual xv ___________________________________________________________________________________ ___________________________________________________________________________________ list of tables table 2-1 feature comparison list ................................................
Page 24
___________________________________________________________________________________ xvi list of tables ___________________________________________________________________________________ issue 11.0 univerge sv8100 table 2-25 cpn for ve 911 calls .........................................................
Page 25
Univerge sv8100 issue 11.0 features and specifications manual xvii ___________________________________________________________________________________ ___________________________________________________________________________________ table 2-50 supported optional equipment (via mgn-u10 etu) ..........
Page 26
___________________________________________________________________________________ xviii list of tables ___________________________________________________________________________________ issue 11.0 univerge sv8100 table 2-77 keys for entering names ....................................................
Page 27
Univerge sv8100 issue 11.0 features and specifications manual xix ___________________________________________________________________________________ ___________________________________________________________________________________ table 2-104 windows mobile devices ..................................
Page 28
___________________________________________________________________________________ xx list of tables ___________________________________________________________________________________ issue 11.0 univerge sv8100 table 2-130 ip recorder basic licenses ...................................................
Page 29: Intr
Features and specifications manual 1 - 1 intr oduction 1 introduction s ection 1 g eneral i nformation univerge sv8100 (dtl and itl telephones), electra elite ipk ii (dth telephones), d term series i (dtr telephones) can be used with the univerge sv8100 system. S ection 2 m ultiline t erminals used ...
Page 30
Issue 11.0 univerge sv8100 1 - 2 introduction electra elite ipk terminals the electra elite ipk series i terminals (dtr/dth telephones) either with or without lcd display offer a variety of colors, and line sizes. Terminals are available in black or white. The large liquid crystal display (lcd) on t...
Page 31
Univerge sv8100 issue 11.0 features and specifications manual 1 - 3 feature access, single on/off, or one-touch keys keys are designated feature access, single on/off, or one-touch throughout this manual. The keys operate much the same, but various limitations imposed on each type are described belo...
Page 32
Issue 11.0 univerge sv8100 1 - 4 introduction 2-line on the dtr-2dt-1. Speakerphone with full handsfree operation and headset jack is standard (except on the dtr-2dt-1). All but the dtr-2dt-1, dtr-1-1, dtr-1hm-1 and cordless terminals are compatible with the ad(a)-r, ap(a)-r, ap(r)-r, ct(a)-r and hf...
Page 33: Features
Features and specifications manual 2 - 1 fe at u re s 2 features s ection 1 a bout t his c hapter this chapter provides an alphabetical listing of the features that are available with the univerge sv8100 system. Each feature provides the following information: description – briefly describes the fea...
Page 34: Ipk II
Issue 11.0 univerge sv8100 2 - 2 features s ection 2 i mportant n otes simplifying multiline terminal operation with one-touch keys a multiline terminal user can access many features using service codes (e.G., service code 744 sets call forward busy/no answer). To streamline the operation of their t...
Page 35
Univerge sv8100 issue 11.0 features and specifications manual 2 - 3 alarm reports alarm reports alphanumeric display alphanumeric display analog communications interface (aci) analog communications interface (aci) ancillary device connection ancillary device connection answer hold answer hold answer...
Page 36
Issue 11.0 univerge sv8100 2 - 4 features caller id caller id not supported caller id – flexible ringing central office calls, answering central office calls, answering central office calls, placing central office calls, placing class of service class of service clock/calendar display clock/calendar...
Page 37
Univerge sv8100 issue 11.0 features and specifications manual 2 - 5 directed call pickup directed call pickup directory dialing directory dialing distinctive ringing, tones and flash patterns distinctive ringing, tones and flash patterns do not disturb do not disturb door box door box drop key drop ...
Page 38
Issue 11.0 univerge sv8100 2 - 6 features handsfree answerback/forced intercom ringing handsfree answerback/forced intercom ringing headset operation headset operation hold hold hot key-pad hot key-pad hotel/motel hotel/motel hotline hotline howler tone service howler tone service intercom intercom ...
Page 39
Univerge sv8100 issue 11.0 features and specifications manual 2 - 7 licensing licensing line preference line preference long conversation cutoff long conversation cutoff not supported loop keys not supported maintenance meet me conference meet me conference meet me paging meet me paging meet me pagi...
Page 40
Issue 11.0 univerge sv8100 2 - 8 features pc programming pc programming power failure transfer power failure transfer prime line selection prime line selection private line private line programmable function keys programmable function keys programming from a multiline terminal programming from a mul...
Page 41
Univerge sv8100 issue 11.0 features and specifications manual 2 - 9 not supported speed dial – telephone book station add-on console sv8100/sv8300 terminals station hunt station hunt station message detail recording station message detail recording station name assignment-user programmable station n...
Page 42
Issue 11.0 univerge sv8100 2 - 10 features s ection 4 f eatures the remainder of this document provides the features for the univerge sv8100 system. Not supported voice response system (vrs) embedded vrs not supported vm8000 inmail upload download audio not supported vm8000 inmail – automatic access...
Page 43
Account code – forced/verified/unverified 2 - 11 a account code – forced/verified/unverified description account codes are user-dialed codes that help the system administrator categorize and/or restrict trunk calls. The system has two types of forced account codes: forced account codes (unverified) ...
Page 44
Issue 11.0 univerge sv8100 2 - 12 account code – forced/verified/unverified verified account codes with verified account codes, the system compares the account code the user dials to a list of up to 2000 programmed codes. If the account code is in the list, the call goes through. If the code dialed ...
Page 45
Univerge sv8100 issue 11.0 account code – forced/verified/unverified 2 - 13 conditions if a user enters a code that exceeds 16 digits, the system ignores the account code entry. If the system has account codes disabled, the digits dialed (e.G., 1234 ) appear on the smdr report as part of the number ...
Page 46
Issue 11.0 univerge sv8100 2 - 14 account code – forced/verified/unverified system availability terminals all terminals required component(s) vrs for forced account codes for single line telephones related features automatic route selection pbx compatibility speed dial – system/group/station station...
Page 47
Univerge sv8100 issue 11.0 account code – forced/verified/unverified 2 - 15 15-07-01 programmable function keys assign a function key as an account code key (code 50). Use this key instead of the dial pad to enter the before and after the account code. Line key 1~48 0~99 (normal function code 751 ...
Page 48
Issue 11.0 univerge sv8100 2 - 16 account code – forced/verified/unverified operation to enter an account code anytime while on a trunk call: the outside caller cannot hear the account code digits you enter. Use this procedure if your system has optional account codes enabled. You may also use this ...
Page 49
Univerge sv8100 issue 11.0 account code – forced/verified/unverified 2 - 17 to enter a forced account code before dialing the outside number: if your system has forced or verified account codes, you may use this procedure instead of letting the system prompt you for your account code. You may also u...
Page 50
Issue 11.0 univerge sv8100 2 - 18 account code – forced/verified/unverified to enter an account code for an incoming call: this procedure is not available for single line telephones. 1. Answer incoming call. If account codes for incoming calls is disabled, the following steps dial digits out onto th...
Page 51: Account Code Entry
Univerge sv8100 issue 11.0 account code entry 2 - 19 account code entry description account codes are user-dialed codes that help the system administrator categorize and/or restrict trunk calls. Optional account codes allow a user to enter an account code while placing a trunk call or anytime while ...
Page 52
Issue 11.0 univerge sv8100 2 - 20 account code entry to simplify account code entry, store the account code (e.G., 1234) in a one-touch key, and press the key instead of dialing the code. Speed dialing bins can contain stored account codes. Prevent them from being displayed using program 20-07-04. W...
Page 53
Univerge sv8100 issue 11.0 account code entry 2 - 21 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature p...
Page 54
Issue 11.0 univerge sv8100 2 - 22 account code entry operation to enter an account code anytime while on a trunk call: the outside caller cannot hear the account code digits you enter. Use this procedure if your system has optional account codes enabled. You may also use this procedure for incoming ...
Page 55
Univerge sv8100 issue 11.0 account code entry 2 - 23 3. Dial . - or - press your account code key (program 15-07 or sc 751: code 50). To enter an account code before dialing the outside number: if your system has forced or verified account codes, you may use this procedure instead of letting the sys...
Page 56
Issue 11.0 univerge sv8100 2 - 24 account code entry to enter an account code at a single line telephone: 1. Access trunk for outside call. Dial a code to access a trunk. Refer to central office calls, placing for more information. 2. Dial 3. Enter account code (1~16 digits). 4. Dial . 5. Dial numbe...
Page 57: Alarm
Univerge sv8100 issue 11.0 alarm 2 - 25 alarm description alarm lets any station extension work like an alarm clock. An extension user can have alarm remind them of a meeting or an appointment. There are two types of alarms: alarm 1 (sounds only once at the preset time) alarm 2 (sounds every day at ...
Page 58
Issue 11.0 univerge sv8100 2 - 26 alarm guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programming. L...
Page 59
Univerge sv8100 issue 11.0 alarm 2 - 27 to silence an alarm: 1. At multiline terminal, press exit. - or - at the single line telephone, lift the handset. The single line set user hears music on hold when the handset is lifted. To check the programmed alarm time at a multiline terminal: 1. Press help...
Page 60
Issue 11.0 univerge sv8100 2 - 28 alarm this page intentionally left blank.
Page 61: Alarm Reports
Univerge sv8100 issue 11.0 alarm reports 2 - 29 alarm reports description the univerge sv8100 system logs various errors and reports information about the operation that can be used to determine the cause of a problem. The system can indicate several errors on the multiline telephone display, output...
Page 62
Issue 11.0 univerge sv8100 2 - 30 alarm reports table 2-2 sample alarm report 05/16/2006 14:30 page 001 lvl no stat date time item unit slt prt parameter min 0002 rec 05/16/06 14:21 pkg installation prt 02 00 maj 0010 err 05/16/06 14:21 isdn link prt 02 12 maj 0010 rec 05/16/06 14:21 isdn link prt 0...
Page 63
Univerge sv8100 issue 11.0 alarm reports 2 - 31 system information the system can print a report of the blades installed, the port assignments, and the port types. This information is sent to the extension defined in program 90-13. Table 2-3 alarm report definitions alarm report heading definitions ...
Page 64
Issue 11.0 univerge sv8100 2 - 32 alarm reports the system information reports indicate: date and time of the report blade names slot condition (working, blocked) port assignment port classification table 2-5 sample system information printout system information 05/18/2006 11:02 slot location type a...
Page 65
Univerge sv8100 issue 11.0 alarm reports 2 - 33 conditions alarm reports and system information reports can be output to a usb stick on the cd-cp00-us. The univerge sv8100 supports the following alarms to be output to the lcd of a multiline terminal: smdr buffer full cd-cp00-us-lan link error the un...
Page 66
Issue 11.0 univerge sv8100 2 - 34 alarm reports up to 100 system alarm reports can be stored. When the buffer fills, the oldest record is deleted to allow the new record to be saved. If the system is set up to email the alarm reports and the mail server is down, the report is not sent. System inform...
Page 67
Univerge sv8100 issue 11.0 alarm reports 2 - 35 system availability terminals all multiline terminals required component(s) when using the version 7.00 feature to email dimlast and dimdump files, the following components are required: usb memory stick pz-me50-us v7000 enhancement license (0036) main...
Page 68
Issue 11.0 univerge sv8100 2 - 36 alarm reports guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progra...
Page 69
Univerge sv8100 issue 11.0 alarm reports 2 - 37 printing reports: printing system information reports: 90-24-02 system alarm report notification time setup – day set the day for the alarm report to print. Day 00~31 (0 = disabled) (default = 00) 90-24-03 system alarm report notification time setup – ...
Page 70
Issue 11.0 univerge sv8100 2 - 38 alarm reports emailing alarm reports: program number program name description/comments assigned data level 1 2 3 10-12-01 cd-cp00-us network setup – ip address assign the ip address. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 191.254.255.254 192.0.0.1~ 223.255.255.254 (def...
Page 71
Univerge sv8100 issue 11.0 alarm reports 2 - 39 90-10-02 system alarm setup – report when enabled the system will provide notification of events for each of the enabled reports. This does not have to be set for dimlast/dimdump files to be sent. 0 = disabled 1 = enabled (default = 0) 90-11-02 system ...
Page 72
Issue 11.0 univerge sv8100 2 - 40 alarm reports inmail smtp setup: 90-11-15 system alarm report – dimlog notification when enabled the system will send an email notification when a system fault occurs and dimlast/ dimdump files are generated. If program 90-11-14 is also enabled the log files will be...
Page 73
Univerge sv8100 issue 11.0 alarm reports 2 - 41 inmail pop3 setup: operation to use this feature at any terminal: the user must be logged in with an installer (in) level password as defined in program 90-02. 47-18-09 vm8000 inmail setup – reply to address set the email address for replies to outgoin...
Page 74
Issue 11.0 univerge sv8100 2 - 42 alarm reports this page intentionally left blank.
Page 75: Alphanumeric Display
Univerge sv8100 issue 11.0 alphanumeric display 2 - 43 alphanumeric display description multibutton display telephones have a 3-line, 24 character-per-line alphanumeric display that provides various feature status messages. These messages help the display telephone user process calls, identify calle...
Page 76
Issue 11.0 univerge sv8100 2 - 44 alphanumeric display guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 77
Univerge sv8100 issue 11.0 alphanumeric display 2 - 45 operation operation is automatic if enabled in programming..
Page 78
Issue 11.0 univerge sv8100 2 - 46 alphanumeric display this page intentionally left blank.
Page 79
Univerge sv8100 issue 11.0 analog communications interface (aci) 2 - 47 analog communications interface (aci) description the analog communications interface (aci) feature uses a pgd(2)-u10 adp (door phone/paging) adapter to provide two analog ports (with associated relays) for music on hold, extern...
Page 80
Issue 11.0 univerge sv8100 2 - 48 analog communications interface (aci) auxiliary device control the pgd(2)-u10 adp can control a customer-provided tape recorder. When an extension user dials the aci analog port extension number, they can automatically start the recorder and activate the record func...
Page 81
Univerge sv8100 issue 11.0 analog communications interface (aci) 2 - 49 physical ports and software ports each pgd(2)-u10 adp has a physical port for connection to the telephone system and two logical ports. For programming, the ports are also called software ports. The physical port connects to a s...
Page 82
Issue 11.0 univerge sv8100 2 - 50 analog communications interface (aci) default settings no pgd(2)-u10 adps programmed. System availability terminals none required component(s) pgd(2)-u10 adp related features automatic call distribution (acd) background music hotline one-touch calling paging, extern...
Page 83
Univerge sv8100 issue 11.0 analog communications interface (aci) 2 - 51 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wi...
Page 84
Issue 11.0 univerge sv8100 2 - 52 analog communications interface (aci) 14-09-01 conversation recording destination for trunks – aci recording destination extension number assign the aci call recording destination per trunk. The destination can be an aci port extension number (assigned in program 11...
Page 85
Univerge sv8100 issue 11.0 analog communications interface (aci) 2 - 53 operation to call an aci software port: 1. Press speaker. 2. Dial aci software port extension number. - or - dial aci department group extension number. - or - press the one-touch key for aci extension or department group. After...
Page 86
Issue 11.0 univerge sv8100 2 - 54 analog communications interface (aci) this page intentionally left blank.
Page 87: Ancillary Device Connection
Univerge sv8100 issue 11.0 ancillary device connection 2 - 55 ancillary device connection description ancillary device connection allows installation of selected peripheral (ancillary) devices to a multiline terminal. This feature enhances peripheral device objectives. An univerge sv8100 multiline t...
Page 88
Issue 11.0 univerge sv8100 2 - 56 ancillary device connection when a single line phone is connected to an ap(r)-r or apr-l, the 2nd channel of esi must be used (programs 10-03-06 and 10-03-07) to switch back and forth between a call and call waiting. Apr-l does not support dtl-2e-1, dtl-6e-1, or all...
Page 89
Univerge sv8100 issue 11.0 ancillary device connection 2 - 57 system availability terminals all multiline terminals except dtr-2dt-1 tel, dtp-2dt-1 tel, and dtp-16hc-1 tel. Required component(s) ap(r)-r ap(a)-r psa-l ada-l apr-l related features electra elite ipk terminals sv8100/sv8300 terminals gu...
Page 90
Issue 11.0 univerge sv8100 2 - 58 ancillary device connection operation depends on the connected ancillary device. 10-03-04 etu setup (lca pkg setup) – receive gain level (r-level) customize the transmit and receive levels of the codec gain types for 500/2500 type single line telephones. 1~63 (-15.5...
Page 91: Answer Hold
Univerge sv8100 issue 11.0 answer hold 2 - 59 answer hold description answer hold allows a multiline terminal user to press the flashing answer key to answer an incoming ringing call or a camp-on call. When the multiline terminal user is already answering a call, the first call is automatically plac...
Page 92
Issue 11.0 univerge sv8100 2 - 60 answer hold required component(s) none related features answer key central office calls, answering guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most ...
Page 93
Univerge sv8100 issue 11.0 answer hold 2 - 61 operation to answer a call on a different line key or cap key with a call in progress: 1. Receive a co/pbx, did/disa/dil/e&m incoming ring. Answer flashes. 2. Press answer, and answer the new call. The answer led goes out. The original call is put on hol...
Page 94
Issue 11.0 univerge sv8100 2 - 62 answer hold this page intentionally left blank.
Page 95: Answer Key
Univerge sv8100 issue 11.0 answer key 2 - 63 answer key description multiline terminals have an answer key with an led that flashes when the multiline terminal user receives an incoming co/pbx, tie/did transfer, or co/pbx transfer call. When multiple calls are received, the answer key is used to pic...
Page 96
Issue 11.0 univerge sv8100 2 - 64 answer key guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmi...
Page 97
Univerge sv8100 issue 11.0 answer key 2 - 65 operation to answer calls using the answer key: 1. Receive co/pbx incoming ring. 2. Press answer. 3. Talk with the co/pbx incoming calling party. 4. When additional co incoming calls are received, press answer to place the current call on hold and connect...
Page 98
Issue 11.0 univerge sv8100 2 - 66 answer key this page intentionally left blank.
Page 99: Attendant Call Queuing
Univerge sv8100 issue 11.0 attendant call queuing 2 - 67 attendant call queuing description attendant extensions can have up to 32 incoming calls queued before additional callers hear a busy tone. This helps minimize call congestion in systems that use the attendant as the overflow destination for u...
Page 100
Issue 11.0 univerge sv8100 2 - 68 attendant call queuing related features call forwarding guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with p...
Page 101
Univerge sv8100 issue 11.0 attendant call queuing 2 - 69 operation none.
Page 102
Issue 11.0 univerge sv8100 2 - 70 attendant call queuing this page intentionally left blank.
Page 103
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 71 automatic call distribution (acd) description automatic call distribution (acd) uniformly distributes calls among agents of a programmed acd group. When a call rings into an acd group, the system automatically routes the call to the...
Page 104
Issue 11.0 univerge sv8100 2 - 72 automatic call distribution (acd) how often the time in queue portion of the display reoccurs. If the supervisor should hear a queue alarm when the time in queue portion reoccurs. This alarm is a single beep tone that reminds the supervisor to check the condition of...
Page 105
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 73 agent identity code (aic) an agent identity code (aic) allows acd agents to log in any extension without setting program 41-02-01. Using aic, acd agents can also log in to multiple acd groups at the same time (up to 64 acd groups). ...
Page 106
Issue 11.0 univerge sv8100 2 - 74 automatic call distribution (acd) multiple agent log in acd agents can log in any extension with multiple aics (up to three). Using the example setup above, acd works as follows: example: example 1: log in with aic 789 and 567 during mode pattern 1, acd agents belon...
Page 107
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 75 busy on a call. Placing an emergency call to the supervisor. Not available or installed. The acd supervisor can use their console also for placing and transferring calls – just like any other extension user. Flexible time schedules ...
Page 108
Issue 11.0 univerge sv8100 2 - 76 automatic call distribution (acd) with a rest mode key programmed on an acd agent’s telephone, when the agent is in rest mode, the key is lit. If the rest mode key is pressed while an agent is on a call, the key flashes to indicate a pre-rest mode status. When the c...
Page 109
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 77 automatic work time: the system implements automatic work time for the agent as soon as they hang up their current call. This is helpful in applications (such as tech service groups) where follow-up paperwork is a requirement for ev...
Page 110
Issue 11.0 univerge sv8100 2 - 78 automatic call distribution (acd) queue status display with scrolling: when all agents in an acd group are unavailable, an incoming call queues and causes the queue status display to occur on the acd group supervisor and/or agent’s display (based on the class of ser...
Page 111
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 79 when logged out of acd group: when acd agents are logged out and a call is placed into the acd queue, the telephones of the logged out agents display the queue status and they hear the alarm according to the settings defined in syst...
Page 112
Issue 11.0 univerge sv8100 2 - 80 automatic call distribution (acd) programmable wrap-up timer when an agent finishes their call, the system automatically starts a wrap-up timer and blocks any acd calls to the agent. This gives them time to complete important logs and records before a new call comes...
Page 113
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 81 if all agents are logged out of an acd queue, a transferred call to the acd pilot number recalls immediately back to the transferring party (version 2500 or lower software). If all agents are logged out of an acd queue, a trunk call...
Page 114
Issue 11.0 univerge sv8100 2 - 82 automatic call distribution (acd) when an agent is in a ring group and logged in, it will not ring when a call comes to the ring group. It will ring when logged out. If a phone has never been brought up and is assigned as an agent, the system will have to be reset b...
Page 115
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 83 a supervisor assigned to not receive calls or take calls after the overflow time is reached shows as idle in mis when they are logged in and idle even when calls are queued up and not reaching the overflow timer. Call detail by queu...
Page 116
Issue 11.0 univerge sv8100 2 - 84 automatic call distribution (acd) night service voice mail integration (analog) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. Thes...
Page 117
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 85 11-13-12 service code setup (for acd) – change agent acd group by supervisor when using service code 669 to change an agent acd group, the supervisor must enter a 2-digit number for the group. For example, to change to acd group 4, ...
Page 118
Issue 11.0 univerge sv8100 2 - 86 automatic call distribution (acd) 15-11-01 virtual extension delayed ring assignment assign the delayed ringing options for an extension virtual extension or virtual extension group answer keys (defined in program 15-09). You make an assignment for each night servic...
Page 119
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 87 30-05-05 dss console lamp table – out of schedule (acd dss) define the led patterns for out of schedule (acd/dss) functions on the dss consoles. Lamp pattern data 0~7 [default = 0 (off)] 30-05-06 dss console lamp table – acd agent l...
Page 120
Issue 11.0 univerge sv8100 2 - 88 automatic call distribution (acd) 41-03-03 incoming ring group assignment for acd group – priority data determine whether an incoming call to a trunk ring group should follow a priority assignment. 0, 1~7 0 = no priority 1 = highest priority 7 = lowest priority (def...
Page 121
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 89 41-07-01 acd weekly schedule setup assign the four work schedules (1~4) to days of the week. The assignments made in this program apply to both the acd agent work schedules (program 41-05) and the trunk work schedules (program 41-06...
Page 122
Issue 11.0 univerge sv8100 2 - 90 automatic call distribution (acd) 41-08-02 acd overflow options – acd overflow destination assign the overflow mode (0~9), destination and announcement message types. Delay announcement functions are not available for acd pilot number calls. Each acd group can have ...
Page 123
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 91 41-10-02 aci delay announcement – 2nd delay announcement aci port number define the aci port number to be used for the delay announcement.This program is activated when the delay announcement source and options are assigned as aci i...
Page 124
Issue 11.0 univerge sv8100 2 - 92 automatic call distribution (acd) 41-11-07 vrs delay announcement – acd forced disconnect time after the 2nd delay message set the time, after the last 2nd delay message is played, before the call is disconnected. 0~64800 (seconds) 0 = no disconnect (default = 60) 4...
Page 125
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 93 41-14-02 acd options setup – automatic wrap up mode define if agents manually enter wrap mode by pressing a key, or are put automatically into wrap mode at end of an acd call. This setting applies to all agents in the selected group...
Page 126
Issue 11.0 univerge sv8100 2 - 94 automatic call distribution (acd) 41-14-13-2 acd options setup – destination number type set various options for acd groups. When an option is set for an acd group, the setting is in force (if applicable) for all agents in the group. For each acd queue (1~64), assig...
Page 127
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 95 41-16-01 acd threshold overflow – number of calls in queue define the maximum number of calls allowed in the acd queue before overflow occurs. 0~200 (0 = no limitation) (default = 0) 41-16-02 acd threshold overflow – operation mode ...
Page 128
Issue 11.0 univerge sv8100 2 - 96 automatic call distribution (acd) 41-18-10 acd agent identity code setup – acd group number in mode 8 for each aic table, define the acd group aic agents are in during mode 8. 0~64 0 = no setting (default = 0) 41-19-01 acd voice mail delay announcement – delay messa...
Page 129
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 97 41-20-02 acd queue display settings – queue status display time program 41-15 can also provide a queue alarm to the agents. The options in program 41-20 should not be used if 41-15 is set. Assign how long the queue status display re...
Page 130
Issue 11.0 univerge sv8100 2 - 98 automatic call distribution (acd) 41-24-02 caller id marking setup – acd agent info for caller id set whether the agent id or extension number of the acd agent is used to mark with the cid in the buffer. 0 = agent extension number 1 = acd agent id (default = 0) 41-2...
Page 131
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 99 operation using the headset with automatic answer for acd agents: 1. With the multiline terminal in an idle state, press feature. 2. Press the headset key (program 15-07-01 or sc 751: 05). The headset key blinks when automatic heads...
Page 132
Issue 11.0 univerge sv8100 2 - 100 automatic call distribution (acd) to log out (for single or multiple agent log ins): multiline terminal all aic log ins become logged out. 1. Press the acd log in/log out key (program 15-07-01 or sc 752: 10). 2. Dial 1 to accept. - or - press speaker and dial the a...
Page 133
Univerge sv8100 issue 11.0 automatic call distribution (acd) 2 - 101 single line telephone follow steps 1~3 to log in with additional aics (up to three) anytime. 1. Lift the handset and dial the aic log in service code (program 11-13-08). 2. Dial the log in code (up to 20 digits). This step is not r...
Page 134
Issue 11.0 univerge sv8100 2 - 102 automatic call distribution (acd) rest mode: to set the manual rest mode: multiline terminal 1. With the multiline terminal idle, press the acd rest mode key (program 15-07-01 or sc 752: 13). The acd rest mode key lights. If the rest mode key is pressed while the a...
Page 135: Automatic Release
Univerge sv8100 issue 11.0 automatic release 2 - 103 automatic release description automatic release drops the line circuit when an outside party abandons the call. For this feature to work with loop start trunks, the co/pbx providing the outside line must provide a timed disconnect signal. Automati...
Page 136
Issue 11.0 univerge sv8100 2 - 104 automatic release related features central office calls, answering central office calls, placing guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most c...
Page 137
Univerge sv8100 issue 11.0 automatic release 2 - 105 80-04-02 call progress tone detector setup – min. Detection level set the minimum detection level. 0~15 detect level 0: –15dbm(0) to –30dbm(15) detect level 1: –30dbm(0) to –45dbm(15) detect level 2: –40dbm(0) to –55dbm(15) default: type 1 (dt) – ...
Page 138
Issue 11.0 univerge sv8100 2 - 106 automatic release 80-04-05 call progress tone detector setup – pulse count set the pulse count. 1~255 default: type 1 (dt) – 1 type 2 (bt) – 1 type 3 (rbt) – 1 type 4, type 5 – 0 80-04-06 call progress tone detector setup – on minimum time set the minimum on time. ...
Page 139
Univerge sv8100 issue 11.0 automatic release 2 - 107 operation none.
Page 140
Issue 11.0 univerge sv8100 2 - 108 automatic release this page intentionally left blank.
Page 141: Automatic Route Selection
Univerge sv8100 issue 11.0 automatic route selection 2 - 109 automatic route selection description automatic route selection (ars) provides call routing and call restriction based on the digits a user dials. Ars gives the system the most cost-effective use of the connected long distance carriers. Ar...
Page 142
Issue 11.0 univerge sv8100 2 - 110 automatic route selection time of day selection for routing, ars provides 10 different day selections (called time schedule patterns). Each time schedule pattern can provide up to 20 time intervals which are assigned to one of the eight day/ night modes. The time s...
Page 143
Univerge sv8100 issue 11.0 automatic route selection 2 - 111 the examples below use the following system programming: program 26-01-03 for ars misdialed number handling as: 1 (warning tone) with program 26-01-06: ars cos match access disabled (set to 0): if at 9:00 am, each extension dialed 9+(203)9...
Page 144
Issue 11.0 univerge sv8100 2 - 112 automatic route selection with program 26-01-06: ars cos match access enabled (set to 1): if at 9:00 am, each extension dialed 9+(203)926-5400 extension 301 would use trunk group 1 extension 302 would use trunk group 2 extension 401, 402 would use trunk group 3 if ...
Page 145
Univerge sv8100 issue 11.0 automatic route selection 2 - 113 if an entry of 911 is programmed in ars, but ars is turned off, 911 calls still attempt to route using ars. When using ars class of service matching, ccis calls will always follow class of service 1. If a user dials a number not programmed...
Page 146
Issue 11.0 univerge sv8100 2 - 114 automatic route selection conditions the recognize extension location when logging in with netlink requires version 7000 or higher software. This feature requires netlink to be enabled. This feature is only supported on dt700 and softphones. Default setting none sy...
Page 147
Univerge sv8100 issue 11.0 automatic route selection 2 - 115 trunk queuing/camp on guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro an...
Page 148
Issue 11.0 univerge sv8100 2 - 116 automatic route selection 12-02-01 automatic night service patterns –start time define the daily pattern of the automatic mode switching. Each mode group has 10 patterns. These patterns are used in programs 12-03 and 12-04. The daily pattern consists of 20 timer se...
Page 149
Univerge sv8100 issue 11.0 automatic route selection 2 - 117 12-03-01 weekly night service switching define which time pattern should be used on each day of the week. Night mode service group numbers: 01~32 time schedule pattern number: 1~10 day of week: 01 = sunday (default = time pattern 2) 02 = m...
Page 150
Issue 11.0 univerge sv8100 2 - 118 automatic route selection 12-07-01 text data for night mode make up an original text message, which, depending on programming, can be displayed on an lcd of a multiline telephone in each mode. Night mode service group number: 01~32 day/night mode: 1~8 text message:...
Page 151
Univerge sv8100 issue 11.0 automatic route selection 2 - 119 14-07-01 trunk access map setup set up the trunk access maps. This sets the access options for trunks. 0 = no access 1 = outgoing access only 2 = incoming access only 3 = access only when trunk on hold 4 = outgoing access and access when t...
Page 152
Issue 11.0 univerge sv8100 2 - 120 automatic route selection 20-08-17 class of service options (outgoing call service) – ars override of trunk access map turn off or on an extension user ability to override the trunk access map programming (program 14-07-01 and program 15-06-01) for outgoing calls. ...
Page 153
Univerge sv8100 issue 11.0 automatic route selection 2 - 121 26-01-07 automatic route selection service – f-route access cos reference define the system options for automatic route selection (ars). 0 = f-route 1 = ars (default = 0) 26-02-01 dial analysis table for ars/lcr – dial enter the digits (16...
Page 154
Issue 11.0 univerge sv8100 2 - 122 automatic route selection 26-02-03 dial analysis table for ars – additional data/service number for each dial analysis table (1~800), if service type 1 was selected in program 26-02-02, enter the trunk group number (0~100, 0 = no route). If service type 1 (in 26-02...
Page 155
Univerge sv8100 issue 11.0 automatic route selection 2 - 123 26-03-01 ars dial treatments – treatment code assign the dial treatments (1~15) for automatic ars dialing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial treatment options are: 3 - delet...
Page 156
Issue 11.0 univerge sv8100 2 - 124 automatic route selection 26-11-01 transit network id table – transmit network id (carrier id) enter the transit network selection information element to be added to an ars call using an isdn trunk. This information element identifies a requested transit network. 0...
Page 157
Univerge sv8100 issue 11.0 automatic route selection 2 - 125 44-02-04 dial analysis table for ars/ f-route access – dial tone simulation determine if the dial tone simulation is on (1) or off (0) for the pre-transaction table for selecting ars/f-route. If enabled, this option sends dial tone to the ...
Page 158
Issue 11.0 univerge sv8100 2 - 126 automatic route selection 44-04-01 ars/f-route selection for time schedule assign each ars/f-route selection number (1~500) to an ars/f-route table number for each ars/f-route time mode. There are eight time modes for ars/f-route access. Ars/f-route time mode: 1~8 ...
Page 159
Univerge sv8100 issue 11.0 automatic route selection 2 - 127 44-05-10 ars/f-route – ccis over ip destination point code for each ars/f-route table (1~500). Set the ccis over ip destination point code (0~16367). 0~16367 (default = 0) 44-05-11 ars/f-route – network specified parameter table for each a...
Page 160
Issue 11.0 univerge sv8100 2 - 128 automatic route selection 44-09-01 weekly schedule for ars/ f-route define a weekly schedule for using ars/f-route day numbers 1~7 (1 = sun, 7 = sat), pattern numbers (1~10). The pattern number is defined in program 44-08-01. 1 = sunday (pattern 1~10) (default patt...
Page 161
Univerge sv8100 issue 11.0 automatic route selection 2 - 129 80-03-03 dtmf tone receiver setup – min. Detect level define the minimum detection level for dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20dbm(0) to – 35dbm(15)...
Page 162
Issue 11.0 univerge sv8100 2 - 130 automatic route selection 80-03-04 dtmf tone receiver setup – max. Detect level define the maximum detection level for dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(0) to – 25dbm(15) de...
Page 163
Univerge sv8100 issue 11.0 automatic route selection 2 - 131 80-03-05 dtmf tone receiver setup – forward twist level define the forward twist level for dtmf tone receiver. 0~9 (1db~10db) default: type 1 = 5 (6dbm) type 2 = 5 (6dbm) type 3 = 5 (6dbm) type 4 = 5 (6dbm) type 5 = 5 (6dbm) 80-03-06 dtmf ...
Page 164
Issue 11.0 univerge sv8100 2 - 132 automatic route selection recognize extension location when logging in with netlink: program number program name description/comments assigned data level 1 2 3 26-01-01 automatic route selection service – ars service enable/disable ars. 0 = disable (off) 1 = enable...
Page 165
Univerge sv8100 issue 11.0 automatic route selection 2 - 133 26-02-01 dial analysis table for ars/lcr – dial enter the digits (16 digits maximum: 1~9, 0 # , @; 800 separate entries) for the dial analysis table which is analyzed by ars/lcr. This table is checked after any programmed f-route operati...
Page 166
Issue 11.0 univerge sv8100 2 - 134 automatic route selection 26-02-03 dial analysis table for ars – additional data/service number for each dial analysis table (1~800), if service type 1 was selected in program 26-02-02, enter the trunk group number (0~100, 0 = no route). If service type 1 (in 26-02...
Page 167
Univerge sv8100 issue 11.0 automatic route selection 2 - 135 26-03-01 ars dial treatments – treatment code assign the dial treatments (1~15) for automatic ars dialing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial treatment options are: 3 - delet...
Page 168
Issue 11.0 univerge sv8100 2 - 136 automatic route selection 26-13-01 ars class of service for netlink (dt700) use to set an extension’s ars class of service when used for netlink. Automatic route selection uses ars class of service when determining how to route an extension’s calls. Day/night mode:...
Page 169
Univerge sv8100 issue 11.0 automatic route selection 2 - 137 operation to place a call using ars: 1. At the multiline terminal, press speaker. - or - at the single line telephone, lift the handset. You hear normal intercom dial tone. 2. Dial 9. You hear a second, “stutter” dial tone. 3. Dial the out...
Page 170
Issue 11.0 univerge sv8100 2 - 138 automatic route selection this page intentionally left blank.
Page 171: Background Music
Background music 2 - 139 b background music description background music (bgm) sends music from a customer-provided music source to the speakers of the multiline telephone when the station is idle. Conditions an aci [pgd(2)-u10 adp] port must be used as an alternate external music on hold or backgro...
Page 172
Issue 11.0 univerge sv8100 2 - 140 background music related features music on hold guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro an...
Page 173
Univerge sv8100 issue 11.0 background music 2 - 141 operation to turn background music on or off: 1. Press idle speaker. 2. Dial 725. 3. Press speaker to hang up..
Page 174
Issue 11.0 univerge sv8100 2 - 142 background music this page intentionally left blank.
Page 175: Barge-In
Univerge sv8100 issue 11.0 barge-in 2 - 143 barge-in description barge-in permits an extension user to break into another extension user’s established call, including conference calls. This sets up a conference-type conversation between the intruding extension and the parties on the initial call. Wi...
Page 176
Issue 11.0 univerge sv8100 2 - 144 barge-in when silent monitor mode is used, mic or feature + 1 can be used to activate speech path to the internal and external parties. With version 5000, the barge-in key has been enhanced to allow for additional data to be assigned to the key. The additional data...
Page 177
Univerge sv8100 issue 11.0 barge-in 2 - 145 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmin...
Page 178
Issue 11.0 univerge sv8100 2 - 146 barge-in operation to barge-in after calling a busy extension: the time in program 21-01-03 must expire before you can barge-in. 1. Call a busy extension. 2. Press barge-in key (program 15-07-01 or sc 751: 34). 20-13-15 class of service options (supplementary servi...
Page 179
Univerge sv8100 issue 11.0 barge-in 2 - 147 to barge-in without first calling the busy extension: 1. Pick up the handset or press speaker. 2. Dial 710. - or - press barge-in key (program 15-07-01 or sc 751: 34). 3. Dial busy extension. The extension user hears a warning tone. The disa user is rerout...
Page 180
Issue 11.0 univerge sv8100 2 - 148 barge-in this page intentionally left blank.
Page 181
Univerge sv8100 issue 11.0 battery backup – system memory 2 - 149 battery backup – system memory description the battery on the cd-cp00-us retains the clock/calendar and last number redial (lnr) buffers for each station when the cd-cp00-us encounters a power loss. With a fully charged battery, the s...
Page 182
Issue 11.0 univerge sv8100 2 - 150 battery backup – system memory system availability terminals none required component(s) none related features battery backup – system power guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programmin...
Page 183
Univerge sv8100 issue 11.0 battery backup – system power 2 - 151 battery backup – system power description a built-in battery provides complete system operating power for approximately 30 minutes during commercial power outages. When optional (locally provided) batteries are connected and fully char...
Page 184
Issue 11.0 univerge sv8100 2 - 152 battery backup – system power programming none operation none.
Page 185: Call Appearance (Cap) Keys
Call appearance (cap) keys 2 - 153 c call appearance (cap) keys description this feature automatically places an outside call on a call appearance key when the system is operated as a hybrid (multifunction) system. These keys can be assigned on any multiline terminal or the same key can appear on mu...
Page 186
Issue 11.0 univerge sv8100 2 - 154 call appearance (cap) keys all flexible line keys on a multiline terminal can be assigned as cap keys in system programming. A conference call involving two outside lines cannot reside on one call appearance key. For call appearance (cap) keys, trunks must be assig...
Page 187
Univerge sv8100 issue 11.0 call appearance (cap) keys 2 - 155 related features automatic route selection call arrival (car) keys central office calls, answering central office calls, placing off-hook signaling programmable function keys secondary incoming extension user programming ability virtual e...
Page 188
Issue 11.0 univerge sv8100 2 - 156 call appearance (cap) keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for ...
Page 189
Univerge sv8100 issue 11.0 call appearance (cap) keys 2 - 157 24-01-01 system options for hold – hold recall time a call on hold recalls the extension that placed it on hold after this time. This time works with the hold recall callback time. 0~64800 (seconds) (default = 90) 24-01-02 system options ...
Page 190
Issue 11.0 univerge sv8100 2 - 158 call appearance (cap) keys operation to place an outgoing call on hold and retrieve it using a multiline terminal: 1. Go off-hook using the handset and wait for internal dial tone. - or - press speaker and wait for internal dial tone. 2. Dial the trunk access code ...
Page 191: Call Arrival (Car) Keys
Univerge sv8100 issue 11.0 call arrival (car) keys 2 - 159 call arrival (car) keys description call arrival (car) keys are software extensions available on the basic and expanded port packages. A call arrival extension assigned to a line key, can appear and ring on an individual station or multiple ...
Page 192
Issue 11.0 univerge sv8100 2 - 160 call arrival (car) keys default setting none system availability terminals all multiline terminals required component(s) none related features virtual extensions guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are as...
Page 193
Univerge sv8100 issue 11.0 call arrival (car) keys 2 - 161 11-04-01 virtual extension numbering assign virtual extension numbers. Up to eight digits 1 201 2 202 3 203 ~ ~ 99 299 100 3601 ~ ~ 256 3857 15-01-01 basic extension data setup – extension name define the extension/virtual extension name. Up...
Page 194
Issue 11.0 univerge sv8100 2 - 162 call arrival (car) keys 15-08-01 incoming virtual extension ring tone setup when an extension or a virtual extension is assigned to the function key on the key telephone, select the ring tone when receiving a call on that key. For acd car keys, only tone pattern 1 ...
Page 195
Univerge sv8100 issue 11.0 call arrival (car) keys 2 - 163 15-18-02 virtual extension key enhanced options – display mode when placing a call on virtual extension key define if calls to or from a virtual extension key display the virtual extension key name or the name of the extension it resides on....
Page 196
Issue 11.0 univerge sv8100 2 - 164 call arrival (car) keys operation to answer a call ringing a call arrival (car) key: 1. Press the flashing call arrival (car) key. To place a call to a call arrival (car) key: 1. Lift the handset, or press speaker. 2. Dial the car key extension, or press the call a...
Page 197: Call Duration Timer
Univerge sv8100 issue 11.0 call duration timer 2 - 165 call duration timer description call duration timer lets a multiline terminal with an lcd time their trunk calls on the telephone display. This helps users that must keep track of their time on the telephone. For incoming trunk calls, the call t...
Page 198
Issue 11.0 univerge sv8100 2 - 166 call duration timer guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 199: Call Forwarding – Centrex
Univerge sv8100 issue 11.0 call forwarding – centrex 2 - 167 call forwarding – centrex description the call forwarding – centrex feature allows a station to forward an incoming pbx/centrex co call to an outside location using the same pbx/centrex co line to free the line for additional use. Call for...
Page 200
Issue 11.0 univerge sv8100 2 - 168 call forwarding – centrex default setting disabled system availability terminals all terminals required component(s) pbx/centrex co line related features call forwarding call arrival (car) keys code restriction direct inward dialing (did) do not disturb door box pb...
Page 201
Univerge sv8100 issue 11.0 call forwarding – centrex 2 - 169 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for f...
Page 202
Issue 11.0 univerge sv8100 2 - 170 call forwarding – centrex 14-04-01 behind pbx setup indicate if the trunk is installed behind a pbx (1) or not (0). There is one item for each night service mode. 0 = stand alone (trunk) 1 = behind pbx (pbx) 2 = not used 3 = ctx assume 9 (default = 0) 20-09-01 clas...
Page 203
Univerge sv8100 issue 11.0 call forwarding – centrex 2 - 171 operation to activate call forwarding – centrex: 1. At a multiline terminal, press speaker. - or - at a single line telephone, lift the handset. 2. Dial the call forwarding split service code (default not assigned). 3. Dial 3 (ctx/pbx). 4....
Page 204
Issue 11.0 univerge sv8100 2 - 172 call forwarding – centrex this page intentionally left blank.
Page 205: Call Forwarding
Univerge sv8100 issue 11.0 call forwarding 2 - 173 call forwarding description call forwarding permits an extension user to redirect their calls to another extension or an off-premise number. Call forwarding ensures that the user’s calls are covered when they are away from their work area. The types...
Page 206
Issue 11.0 univerge sv8100 2 - 174 call forwarding call forwarding reroutes calls ringing an extension, including calls transferred from another extension. Call forwarding can also be split, allowing internal and external calls to forward to different destinations. The extension user can enable call...
Page 207
Univerge sv8100 issue 11.0 call forwarding 2 - 175 when a call is transferred because of call forwarding no answer, call forwarding busy, or dnd, the reason for transfer option can display to the transferred extension why the call is ringing their telephone. An extension user can forward their calls...
Page 208
Issue 11.0 univerge sv8100 2 - 176 call forwarding when the following are done in sequence, call forwarding busy is set to extension call forwarding immediate is set on extension call forwarding immediate is cancelled on extension then, call forwarding busy/no answer is set back on the extension. Th...
Page 209
Univerge sv8100 issue 11.0 call forwarding 2 - 177 department calling direct station selection (dss) console do not disturb programmable function keys voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when progra...
Page 210
Issue 11.0 univerge sv8100 2 - 178 call forwarding 11-11-03 service code setup (for setup/ entry operation) – call forward – no answer set the service code for setting call forwarding for no answer. Mlt, slt (default = 743) 11-11-04 service code setup (for setup/ entry operation) – call forward – bu...
Page 211
Univerge sv8100 issue 11.0 call forwarding 2 - 179 11-11-55 service code setup (for setup/ entry operation) – call forward busy no answer destination (no split) set or cancel the call forward busy or no answer destination with no split. Mlt, slt (default = 793) 11-11-58 service code setup (for setup...
Page 212
Issue 11.0 univerge sv8100 2 - 180 call forwarding 20-11-01 class of service options (hold/ transfer service) – call forward all turn off or on an extension user ability to set call forward immediate. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-02 class of service options (hold/ transfer service...
Page 213
Univerge sv8100 issue 11.0 call forwarding 2 - 181 operation to set call forward – immediate at a forwarding station: 1. Pick up the handset or press speaker. 24-09-01 call forward split settings – call forwarding type: assign call forwarding type and the destination numbers for each extension/virtu...
Page 214
Issue 11.0 univerge sv8100 2 - 182 call forwarding 2. Dial the call forward – immediate service code (default: 741). - or - at the multiline terminal only, press the call forwarding programmable function keys. (program 15-07-01, 10 or sc 751, key code 10) 3. Dial 1 (set). 4. Dial the destination ext...
Page 215
Univerge sv8100 issue 11.0 call forwarding 2 - 183 to cancel call forward – busy/no answer at a forwarding station: 1. Pick up the handset or press speaker. 2. Dial the call forward – busy/no answer service code (default: 744). - or - at the multiline terminal only, press the call forwarding program...
Page 216
Issue 11.0 univerge sv8100 2 - 184 call forwarding to set call forward – follow me from the destination station: 1. Pick up the handset or press speaker. 2. Dial the call forward – follow me service code (default: 746). - or - at the multiline terminal only, press the call forwarding programmable fu...
Page 217
Univerge sv8100 issue 11.0 call forwarding 2 - 185 to cancel call forward immediate for any extension: 1. Pick up the handset or press speaker. 2. Dial the call forward immediate for any extension to destination service code (default: 790). 3. Dial 0 (cancel). 4. Dial the station number which is for...
Page 218
Issue 11.0 univerge sv8100 2 - 186 call forwarding to cancel call forward – immediate at a forwarding station: 1. Press the idle virtual extension key. 2. Dial the call forward – immediate service code (default: 741). 3. Dial 0 (cancel). 4. Press speaker or hang up. To set call forward – busy/no ans...
Page 219
Univerge sv8100 issue 11.0 call forwarding with follow me 2 - 187 call forwarding with follow me description while at a co-worker’s desk, a user can have call forwarding with follow me redirect their calls to the co-worker’s extension. This helps an employee who gets detained at a co-worker’s desk l...
Page 220
Issue 11.0 univerge sv8100 2 - 188 call forwarding with follow me related features do not disturb programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly...
Page 221
Univerge sv8100 issue 11.0 call forwarding with follow me 2 - 189 operation to activate call forward follow me from a multiline terminal: 1. At a multiline terminal, other than your own, press speaker and dial service code (746, program 11-11-07). - or - press the call forward follow me key (program...
Page 222
Issue 11.0 univerge sv8100 2 - 190 call forwarding with follow me this page intentionally left blank.
Page 223: Call Forwarding, Off-Premise
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 191 call forwarding, off-premise description off-premise call forwarding allows an extension user to forward their calls to an off-site location. By enabling call forward, off-premise, the user can stay in touch by having the system forward...
Page 224
Issue 11.0 univerge sv8100 2 - 192 call forwarding, off-premise did calls to an extension with off-premise call forwarding set do not recall if there is no answer. Door boxes must be programmed for the calls to be transferred off-premise. The outside number call forwarding dials can be only a number...
Page 225
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 193 door box virtual extensions voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used...
Page 226
Issue 11.0 univerge sv8100 2 - 194 call forwarding, off-premise 11-11-04 service code setup (for setup/ entry operation) – call forward – busy/no answer assign the call forward busy no answer service code. Mlt, slt (default = 744) 11-11-05 service code setup (for setup/ entry operation) – call forwa...
Page 227
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 195 15-07-01 programmable function keys assign functions to multiline terminal line keys. Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 20-06-01 class of service fo...
Page 228
Issue 11.0 univerge sv8100 2 - 196 call forwarding, off-premise 21-03-01 trunk group routing for trunks used to set the trunk route table for automatic external call forward. Day night/mode: 1~8 0~100 (0 = no setting) (default = 1) 24-02-07 system options for transfer – trunk-to-trunk transfer relea...
Page 229
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 197 trunk-to-trunk forwarding – normal (0) trunks: 25-07-07 system timers for vrs/disa – long conversation warning tone time determine the time a disa caller or any trunk-to-trunk (such as tandem trunking) conversation can talk before the l...
Page 230
Issue 11.0 univerge sv8100 2 - 198 call forwarding, off-premise 14-01-26 basic trunk data setup – automatic trunk-to-trunk transfer mode enable (1)/disable (0) each trunk ability to use step transfer. 0 = normal transfer (normal) 1 = step transfer (step) (default = 0) 20-06-01 class of service for e...
Page 231
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 199 trunk-to-trunk forwarding – did (3) trunk forwarding by department groups: refer to departmental calling for additional department group programming. Program number program name description/comments assigned data level 1 2 3 11-07-01 de...
Page 232
Issue 11.0 univerge sv8100 2 - 200 call forwarding, off-premise 14-06-01 trunk group routing – priority order number set the priority order number 1~4. 0 = not specify 1~100 : (trunk group number) 1001~1100 : (1000 + route table number) default: route 1, order number 1 = 1 (trunk group 1) order numb...
Page 233
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 201 trunk-to-trunk forwarding – did (3) trunk forwarding using did translation table: refer to direct inward dialing (did) for additional did programming. Operation to activate call forwarding off-premise non-split: 1. At a multiline termin...
Page 234
Issue 11.0 univerge sv8100 2 - 202 call forwarding, off-premise to cancel call forwarding off-premise non-split: 1. At a multiline terminal, press speaker. - or - at a single line telephone, lift the handset. 2. Dial the call forward access code (default not assigned). 3. Dial 0 (cancel). To activat...
Page 235
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 203 to activate call forwarding off-premise for a door box: this option only works for isdn pri or bri trunks. 1. At the multiline terminal, press speaker + dial sc 722. - or - at the multiline terminal only, press call forward (device) key...
Page 236
Issue 11.0 univerge sv8100 2 - 204 call forwarding, off-premise cancel the line forwarding: 1. Lift the handset. 2. Dial 735. 3. Dial trunk port number (7 001~200) to be defined. 4. Select the mode (1~8) to be defined. 5. Press the exit key. 6. Press speaker to hang up. Automatic trunk-to-trunk tran...
Page 237
Univerge sv8100 issue 11.0 call forwarding, off-premise 2 - 205 6. Press hold to accept the entry. 7. Repeat from step 3 to define another time mode entry or press speaker to hang up. Cancel the line forwarding: 1. Lift the handset. 2. Dial 604. 3. Dial the department group number (01~64) to be defi...
Page 238
Issue 11.0 univerge sv8100 2 - 206 call forwarding, off-premise this page intentionally left blank.
Page 239
Univerge sv8100 issue 11.0 call forwarding/do not disturb override 2 - 207 call forwarding/do not disturb override description an extension user can override call forwarding or do not disturb at another extension. This is helpful, for example, to dispatchers and office managers that always need to g...
Page 240
Issue 11.0 univerge sv8100 2 - 208 call forwarding/do not disturb override guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro...
Page 241
Univerge sv8100 issue 11.0 call forwarding/do not disturb override 2 - 209 operation to override an extension call forwarding or do not disturb: 1. Call the forwarded or dnd extension. 2. Press the override key (program 15-07 or sc 751: 37)..
Page 242
Issue 11.0 univerge sv8100 2 - 210 call forwarding/do not disturb override this page intentionally left blank.
Page 243: Call Monitoring
Univerge sv8100 issue 11.0 call monitoring 2 - 211 call monitoring description call monitoring allows selected multiline terminal users to monitor another user’s conversation without participating. A programmable audible alert tone can be sent to that station user. Without the audible alert (silent ...
Page 244
Issue 11.0 univerge sv8100 2 - 212 call monitoring with program 20-13-10 set to 1, a call which is being monitored can be placed on park by the originator of the outside call, but only the outside caller is placed in park. The extension which is monitoring the call is dropped. When program 20-13-10 ...
Page 245
Univerge sv8100 issue 11.0 call monitoring 2 - 213 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pro...
Page 246
Issue 11.0 univerge sv8100 2 - 214 call monitoring operation the call must be set up for about 10 seconds before it can be monitored. Listen for busy/ring or busy tone. 20-13-17 class of service options (supplementary service) – barge-in tone/display (intrusion tone) turn off or on the barge-in (int...
Page 247
Univerge sv8100 issue 11.0 call monitoring 2 - 215 to call monitor after calling a busy extension: 1. Call a busy extension. 2. Press the barge-in key (program 15-07 or sc 751: 34). - or - the following steps are not available for disa or tie line trunks. 1. Dial the extension number of the busy int...
Page 248
Issue 11.0 univerge sv8100 2 - 216 call monitoring this page intentionally left blank.
Page 249: Call Redirect
Univerge sv8100 issue 11.0 call redirect 2 - 217 call redirect description call redirect allows a multiline terminal user to transfer a call to a predefined destination (such as an operator, voice mail, or another extension) without answering the call. This can be useful if you are on a call and ano...
Page 250
Issue 11.0 univerge sv8100 2 - 218 call redirect default setting enabled system availability terminals all multiline terminals required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programmi...
Page 251
Univerge sv8100 issue 11.0 call redirect 2 - 219 operation to redirect a ringing call: with an incoming call ringing your extension, press the call redirect key (program 15-07 or sc 751: 49 + destination extension number) without lifting the handset. 20-06-01 class of service for extensions assign a...
Page 252
Issue 11.0 univerge sv8100 2 - 220 call redirect this page intentionally left blank.
Page 253: Call Waiting/camp-On
Univerge sv8100 issue 11.0 call waiting/camp-on 2 - 221 call waiting/camp-on description with call waiting, an extension user may call a busy extension and wait in line (camp-on) without hanging up. When the user camps-on, the system signals the busy extension with two beeps indicating the waiting c...
Page 254
Issue 11.0 univerge sv8100 2 - 222 call waiting/camp-on related features callback off-hook signaling programmable function keys transfer trunk queuing/camp on guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature i...
Page 255
Univerge sv8100 issue 11.0 call waiting/camp-on 2 - 223 15-02-06 multiline telephone basic data setup – hold key operating mode set the function of the multiline hold key. Hold can activate normal hold or exclusive hold. 0 = normal (common) 1 = exclusive hold (default = 0) 15-02-12 multiline telepho...
Page 256
Issue 11.0 univerge sv8100 2 - 224 call waiting/camp-on 20-09-01 class of service options (incoming call service) – second call for did/disa/ddi/ dil/ e&m override turn off or on an extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, the d...
Page 257
Univerge sv8100 issue 11.0 call waiting/camp-on 2 - 225 operation to camp-on a busy extension: 1. Call the busy extension. 2. Dial # or press the camp-on key (program 15-07 or sc 751: 35). 3. Do not hang up. To camp-on to a trunk, refer to trunk queuing/camp-on on page 2-1593 . To cancel a camp-on r...
Page 258
Issue 11.0 univerge sv8100 2 - 226 call waiting/camp-on this page intentionally left blank.
Page 259: Callback
Univerge sv8100 issue 11.0 callback 2 - 227 callback description when an extension user calls a co-worker that does not answer or is busy, they can leave a callback request for a return call. The user does not have to repeatedly call the unanswered extension back, hoping to find it idle. The system ...
Page 260
Issue 11.0 univerge sv8100 2 - 228 callback system availability terminals all terminals required component(s) none related features call waiting/camp-on) programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when prog...
Page 261
Univerge sv8100 issue 11.0 callback 2 - 229 operation to place a callback: 1. Call unavailable (busy or unanswered) extension. 2. Dial # or press the callback key (program 15-07 or sc 751: 35). 3. Hang up. 4. Lift the handset when busy extension calls you back. If the unavailable extension was unans...
Page 262
Issue 11.0 univerge sv8100 2 - 230 callback to test callback at a single line telephone: 1. Lift the handset. 2. Dial 799. 3. Hang up. 4. When the telephone rings, lift the handset. You hear the hold tone. 5. Hang up..
Page 263: Caller Id Call Return
Univerge sv8100 issue 11.0 caller id call return 2 - 231 caller id call return description the caller id call return feature allows the voice mail system to use caller id information captured with the message to call and connect the person that left the message with the voice mail user that is check...
Page 264
Issue 11.0 univerge sv8100 2 - 232 caller id call return a telephone used as an acd plus agent or supervisor station should not have mailboxes that support softkeys. Softkeys can be disabled per mailbox in access codes options by enabling hands free play for a particular station. On the um8000 mail,...
Page 265
Univerge sv8100 issue 11.0 caller id call return 2 - 233 related features um8000 mail vm8000 inmail guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are u...
Page 266
Issue 11.0 univerge sv8100 2 - 234 caller id call return operation to return call from the um8000 mail: 1. While listening to a message with cid information press more, more then call softkeys. - or - dial # , 0. 2. To exit from the call, hang up. To return call from the vm8000 inmail: 1. While list...
Page 267: Caller Id
Univerge sv8100 issue 11.0 caller id 2 - 235 caller id description caller id allows a display terminal to show an incoming caller’s telephone number (called the directory number or dn) and optional name. The caller id information is available as pre-answer display. With the pre-answer display, the u...
Page 268
Issue 11.0 univerge sv8100 2 - 236 caller id the telephone display can show up to 12 caller id digits (for non-acd calls). Once installed and programmed, caller id is enabled for all trunk calls, including: ring group calls calls transferred from another extension calls transferred from the vrs call...
Page 269
Univerge sv8100 issue 11.0 caller id 2 - 237 caller id data can also output to a pc or other type of computer through the 1st-party tapi driver. This allows for off-line database lookups. In a customer service department, for example, the computer could search for a caller’s records and display thei...
Page 270
Issue 11.0 univerge sv8100 2 - 238 caller id an additional digit (such as 1) may be required to complete the call (program 10-02-04). For example: incoming caller id shows: 2125551212. If your area code is not 212, define a 1 in program 10-02-04. When callback is executed, the system prefixes 1 on t...
Page 271
Univerge sv8100 issue 11.0 caller id 2 - 239 trunks with privacy release enabled display caller id until the call is answered. To view it after the call has been picked up, press the line key, which sets the call to private mode. To keep the call on privacy release, press the help + exit keys. An ex...
Page 272
Issue 11.0 univerge sv8100 2 - 240 caller id memo display function with version 4000 or lower software, the sv8100 can display matching caller id but is limited to 12 characters. With version 5000 or higher software, it can now display up to 28 characters per line and up to three lines of informatio...
Page 273
Univerge sv8100 issue 11.0 caller id 2 - 241 system availability terminals all multiline terminals with display and single line telephones equipped to receive caller id. Required component(s) cd-4cotb with pz-4cotf daughter board cd-2bria with pz-2bria daughter board cd-prta related features automat...
Page 274
Issue 11.0 univerge sv8100 2 - 242 caller id guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmi...
Page 275
Univerge sv8100 issue 11.0 caller id 2 - 243 14-01-20 basic trunk data setup – block outgoing caller id enable/disable the system from automatically blocking outgoing caller id information when a user places a call.If allowed (i.E. Block, enabled), the system automatically inserts the caller id bloc...
Page 276
Issue 11.0 univerge sv8100 2 - 244 caller id 15-03-09 single line telephone basic data setup – caller id function – for external module enable/disable the caller id fsk signal for an external caller id module or a 3rd-party vendor telephone with caller id display. If voice mail is used, this setting...
Page 277
Univerge sv8100 issue 11.0 caller id 2 - 245 20-09-04 class of service options (incoming call service) – notification for incoming call list existence determine whether or not the check list message is displayed to indicate a missed call. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-06 class of s...
Page 278
Issue 11.0 univerge sv8100 2 - 246 caller id memo display function: 90-03-01 save data save the programmed data on the sram and flash rom to the 16mb/32mb ata removable compact flash memory card. Also, used to save stored caller id if permanently saved with service code #*#9 (11-15-03). Dial 1 + pre...
Page 279
Univerge sv8100 issue 11.0 caller id 2 - 247 operation storing a number: to store a caller id number in an speed dial bin: 1. With a multiline terminal idle, the display shows: 2. Press the list softkey. - or - press the left cursor key twice and skip step 3. The display shows: 3. Press the cid soft...
Page 280
Issue 11.0 univerge sv8100 2 - 248 caller id 4. Press the store softkey. The display shows: ## = list number xx = caller id number mm-dd hh:mm = incoming date and time sta = store in station speed dial bin. Sys - store in system speed dial bin. 5. Press the sta or sys softkey. The display shows: 6. ...
Page 281
Univerge sv8100 issue 11.0 caller id 2 - 249 9. Press transfer. The display shows: 10. Press speaker. The telephone returns to idle. To store a caller id number in a one-touch key: 1. With a telephone idle, the display shows: 2. Press the list softkey. - or - press the left cursor key twice and skip...
Page 282
Issue 11.0 univerge sv8100 2 - 250 caller id 3. Press the cid softkey (caller id). The display shows: ## = list number xx = caller id number mm-dd hh:mm = incoming date and time = preview list = next list store = store in list del = delete from list 4. Press the store softkey. The display shows: ## ...
Page 283
Univerge sv8100 issue 11.0 caller id 2 - 251 9. Press hold. The display shows: 10. Press speaker. The telephone returns to idle. Temporary memory an unanswered call causes the call history key (program 15-07 or sc 751: 08) to flash, indicating a new call was placed in the temporary memory. If enable...
Page 284
Issue 11.0 univerge sv8100 2 - 252 caller id 2. Press cid. The first row of your display shows the caller id number. If there is an “ ” next to the call record number in the left-hand corner, this indicates that it is a call you missed (unanswered). The second row shows the date and time of the call...
Page 285
Univerge sv8100 issue 11.0 caller id – flexible ringing 2 - 253 caller id – flexible ringing description the caller id – flexible ringing feature provides several different options for rerouting calls based on the caller id received. Reject/reroute “private” caller id calls when an analog or isdn tr...
Page 286
Issue 11.0 univerge sv8100 2 - 254 caller id – flexible ringing to transfer the “private” caller id incoming call to extension 301 as ring pattern 2: program 14-01-27: 1 (reject) program 22-18-01: 1 (extension number) program 22-18-02: 301 (extension 301) program 22-18-03: 2 (ring pattern 2) then, t...
Page 287
Univerge sv8100 issue 11.0 caller id – flexible ringing 2 - 255 conditions caller id matching. The univerge sv8100 compares the caller id and programmed speed dial and allows/ denies as indicated below. The speed dial table is searched from the starting number and the first match result is used. The...
Page 288
Issue 11.0 univerge sv8100 2 - 256 caller id – flexible ringing system availability terminals all terminals required component(s) sv8100 main software version 3000 or higher related features central office calls, answering direct inward dialing (did) um8000 mail voice response system (vrs) guide to ...
Page 289
Univerge sv8100 issue 11.0 caller id – flexible ringing 2 - 257 11-10-34 service code setup (for system administrator) – set caller id refuse enable/disable the caller id number (trunks) which are set in program 14-01-27. Mlt, slt (default not assigned) 13-02-01 group speed dialing bins designate th...
Page 290
Issue 11.0 univerge sv8100 2 - 258 caller id – flexible ringing the caller id – flexible ringing flowchart below helps define programming: 14-01-27 basic trunk data setup – caller id refuse setup define if the trunk will reject the call by playing the vrs message based on the caller id information. ...
Page 291
Univerge sv8100 issue 11.0 caller id – flexible ringing 2 - 259 incoming trunk call caller id number exists? Search refusing speed dial area prg 22-16 data exists? 2 go to chart 2 no no yes yes prg 14-01-27: 1 and refuse mode is? Play vrs message prg 40-10-07 disconnect the call search prg 13-04-01 ...
Page 292
Issue 11.0 univerge sv8100 2 - 260 caller id – flexible ringing operation none follow prg 22-02-01 ring the extension number ring the incoming ring group disconnect the call play vrs message prg 40-10-07 prg 14-01-27: 1 and refuse mode is? 2 off on anything else private reason of no caller id? Prg 2...
Page 293
Univerge sv8100 issue 11.0 central office calls, answering 2 - 261 central office calls, answering description the system provides flexible routing of incoming co (trunks) calls to meet the exact site requirements. This lets trunk calls ring and be answered at any combination of system extensions. A...
Page 294
Issue 11.0 univerge sv8100 2 - 262 central office calls, answering sidetone volume setup this option allows system programming for the multiline terminal side tone volume. There are two levels, based on whether the connected trunk is a digital trunk or analog trunk. Side tone auto setup per each ana...
Page 295
Univerge sv8100 issue 11.0 central office calls, answering 2 - 263 dt300/dt700 terminals installed in a sv8100 with the ipk/ipk ii migration system do not support the desi-less page switching and blinking. Desi-less screen page switching only applies to idle terminals. If a terminal is not idle, the...
Page 296
Issue 11.0 univerge sv8100 2 - 264 central office calls, answering isdn compatibility line preference long conversation cutoff night service programmable function keys selectable display messaging warning tone for long conversation guide to feature programming the level 1, level 2 and level 3 column...
Page 297
Univerge sv8100 issue 11.0 central office calls, answering 2 - 265 14-01-02 basic trunk data setup – transmit level customize the transmit and receive levels of the codec gain types for each trunk. Trunks 1~200 1~63 (-15.5 ~ +15.5db in 0.5db intervals) [default = 32 (0db)] 14-01-03 basic trunk data ...
Page 298
Issue 11.0 univerge sv8100 2 - 266 central office calls, answering 14-07-01 trunk access map setup set up the trunk access maps. This sets the access options for trunks. Ring group programming overrides access map programming. 0 = no access 1 = outgoing access only 2 = incoming access only 3 = acces...
Page 299
Univerge sv8100 issue 11.0 central office calls, answering 2 - 267 15-02-01 multiline telephone basic data setup – display language selection (to select options 8~10, press either 8 or recall, then press line keys 1~3. Key 1 is option 8, key 2 is option 9, and key 3 is option 10.) define the display...
Page 300
Issue 11.0 univerge sv8100 2 - 268 central office calls, answering 15-06-01 trunk access map for extensions assign trunk access maps to extensions. Trunks 1~200 (default = 1) 15-07-01 programmable function keys assign functions to multiline terminal line keys. Line key 1~48 0~99 (normal function cod...
Page 301
Univerge sv8100 issue 11.0 central office calls, answering 2 - 269 20-10-07 class of service options (answer service) – automatic off-hook answer turn off or on an extension user ability to use universal auto answer (no service code required). 0 = off 1 = on (default = 0 for cos 1~15) 20-13-13 class...
Page 302
Issue 11.0 univerge sv8100 2 - 270 central office calls, answering 22-02-01 incoming call trunk setup set the feature type for the trunk you are programming. Trunks 1~200 0 = normal 1 = vrs (second dial tone if no vrs installed) 2 = disa 3 = did 4 = dil 5 = e&m tie line 6 = delayed vrs 7 = ani/dnis ...
Page 303
Univerge sv8100 issue 11.0 central office calls, answering 2 - 271 22-07-01 dil assignment assign the destination extension for each dil incoming trunk (001~200). For this selection to work, set program 22-02-01 to 4 (dil). Extension number (maximum eight digits) (default not assigned) 22-08-01 dil/...
Page 304
Issue 11.0 univerge sv8100 2 - 272 central office calls, answering operation to answer an incoming trunk call: 1. Lift the handset. To use universal answer to answer a call ringing over the paging system: 1. Go off-hook. Depending on system programming, this may answer the call and you can skip step...
Page 305
Univerge sv8100 issue 11.0 central office calls, placing 2 - 273 central office calls, placing description the system provides flexibility in the way each extension user can place outgoing trunk calls. This lets you customize the call placing options to meet site requirements and each individual’s n...
Page 306
Issue 11.0 univerge sv8100 2 - 274 central office calls, placing during the trunk measurement process, the following lcd indications are provided: during measurement: measurement (x/4) x = number of measurements measure complete: complete error condition: error trunk busy: busy after successful meas...
Page 307
Univerge sv8100 issue 11.0 central office calls, placing 2 - 275 default setting enabled system availability terminals all multiline terminals required component(s) any trunk blade (i.E., cd-4cotb, cd-2bria, cd-prta, etc.) related features alphanumeric display automatic route selection call appearan...
Page 308
Issue 11.0 univerge sv8100 2 - 276 central office calls, placing guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards f...
Page 309
Univerge sv8100 issue 11.0 central office calls, placing 2 - 277 11-12-14 service code setup (for service access) – trunk group access define the service code which should be used by an extension user to select outgoing trunk group. Mlt, slt (default = 704) 14-01-01 basic trunk data setup – trunk na...
Page 310
Issue 11.0 univerge sv8100 2 - 278 central office calls, placing 14-05-01 trunk group – trunk group number assign trunks to trunk groups. You can also assign the outbound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in the o...
Page 311
Univerge sv8100 issue 11.0 central office calls, placing 2 - 279 14-07-01 trunk access map setup set up the trunk access maps. This sets the access options for trunks. Ring group programming overrides access map programming. 0 = no access 1 = outgoing access only 2 = incoming access only 3 = access ...
Page 312
Issue 11.0 univerge sv8100 2 - 280 central office calls, placing 15-02-08 multiline telephone basic data setup – automatic handsfree set whether pressing a key accesses a one-touch key or preselects the key. 0 = preselect 1 = one-touch (automatic handsfree) (default = 1) 15-03-03 single line telepho...
Page 313
Univerge sv8100 issue 11.0 central office calls, placing 2 - 281 20-13-13 class of service options (supplementary service) – continued dialing (dtmf) signal on icm call turn off or on an extension ability to use continued dialing, which allows dtmf signal sending while talking on extension. 0 = off ...
Page 314
Issue 11.0 univerge sv8100 2 - 282 central office calls, placing operation to place a call over a trunk group: 1. Go off-hook. 2. Dial 704. 3. Dial trunk group number (001~100). 4. Dial the number. - or - 1. At the multiline terminal, press the trunk group key (program 15-07-01 or sc 751: 02 + group...
Page 315
Univerge sv8100 issue 11.0 central office calls, placing 2 - 283 to place a call using trunk group routing: 1. Go off-hook. 2. Dial 9. If your system has an alternate trunk route access code, you may dial that instead. 3. Dial the number. - or - 1. At the multiline terminal, press the trunk group ro...
Page 316
Issue 11.0 univerge sv8100 2 - 284 central office calls, placing this page intentionally left blank.
Page 317: Class of Service
Univerge sv8100 issue 11.0 class of service 2 - 285 class of service description class of service (cos) sets various features and dialing options (called items) for extensions. The system allows any number of extensions to share the same class of service. An extension can have a different class of s...
Page 318
Issue 11.0 univerge sv8100 2 - 286 class of service default setting the attendant (extension 101) has class of service 15 in all night service modes. All other extensions have class of service 1 in all night service modes. If changing class of service via service code: an extension can use service c...
Page 319
Univerge sv8100 issue 11.0 class of service 2 - 287 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pr...
Page 320
Issue 11.0 univerge sv8100 2 - 288 class of service 20-07-05 class of service options (administrator level) – set/ cancel automatic trunk-to- trunk transfer turn off or on an extension user ability to use the trunk-to-trunk forwarding service codes. 0 = off 1 = on (default = 0 for cos 1~15) 20-07-10...
Page 321
Univerge sv8100 issue 11.0 class of service 2 - 289 20-07-19 class of service options (administrator level) – smdr printout department group (stg) data determine if the department group stg) data is included in the smdr printout for each class of service. 0 = off 1 = on (default = 0 for cos 1~14) (d...
Page 322
Issue 11.0 univerge sv8100 2 - 290 class of service 20-08-03 class of service options (outgoing call service) – system speed dialing turn off or on an extension user ability to make outbound calls using system speed dial numbers. 0 = off 1 = on (default = 1 for cos 1~15) 20-08-04 class of service op...
Page 323
Univerge sv8100 issue 11.0 class of service 2 - 291 20-08-13 class of service options (outgoing call service) – isdn clip determine if the isdn calling line identity presentation and screening indicators are to be allowed. 0 = off 1 = on (default = 0 for cos 1~15) 20-08-14 class of service options (...
Page 324
Issue 11.0 univerge sv8100 2 - 292 class of service 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m override turn off or on the extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, the destinati...
Page 325
Univerge sv8100 issue 11.0 class of service 2 - 293 20-10-01 class of service options (answer service) – group call pickup (within group) turn off or on group call pickup for calls ringing an extension pickup group as well as ring group calls (service code # ). 0 = off 1 = on (default = 1 for cos ...
Page 326
Issue 11.0 univerge sv8100 2 - 294 class of service 20-11-01 class of service options (hold/ transfer service) – call forward all turn off or on an extension user ability to set call forward immediate. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-02 class of service options (hold/ transfer servic...
Page 327
Univerge sv8100 issue 11.0 class of service 2 - 295 20-11-12 class of service options (hold/ transfer service) – call forwarding off-premise (external call forwarding) turn off or on an extension user ability to set up call forwarding off-premise at the extension. 0 = off 1 = on (default = 0 for cos...
Page 328
Issue 11.0 univerge sv8100 2 - 296 class of service 20-11-22 class of service options (hold/ transfer service) – restricted unsupervised conference allow/deny an extension user to initiate a trunk-to-trunk transfer (tandem trunking). 0 = allow 1 = deny (default = 0 for cos 1~15) 20-11-23 class of se...
Page 329
Univerge sv8100 issue 11.0 class of service 2 - 297 20-13-04 class of service options (supplementary service) – call forward/dnd override (bypass call) turn off or on the ability to use call forwarding/dnd override. 0 = off 1 = on (default = 1 for cos 1~15) 20-13-05 class of service options (supplem...
Page 330
Issue 11.0 univerge sv8100 2 - 298 class of service 20-13-15 class of service options (supplementary service) – barge-in, initiate turn off or on an extension user ability to barge-in on other's calls. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-16 class of service options (supplementary service...
Page 331
Univerge sv8100 issue 11.0 class of service 2 - 299 20-13-26 class of service options (supplementary service) – group listen turn off or on an extension user ability to use group listen. 0 = off 1 = on (default = 1 for cos 1~15) 20-13-27 class of service options (supplementary service) – busy on sei...
Page 332
Issue 11.0 univerge sv8100 2 - 300 class of service 20-13-36 class of service options (supplementary service) – call duration timer display turn off or on a call timer for the extension. 0 = off 1 = on (default = 1 for cos 01~15) 20-13-38 class of service options (supplementary service) – headset ri...
Page 333
Univerge sv8100 issue 11.0 class of service 2 - 301 20-13-49 class of service options (supplementary service) – blf indication on co incoming state determine if a blf of the station lights when a normal co call is ringing the phone. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-50 class of service...
Page 334
Issue 11.0 univerge sv8100 2 - 302 class of service operation to change an extension class of service (via service code 677): 1. Press speaker. 2. Dial 677. 3. Dial the extension number you want to change. You see: mode1:nn press hold to leave the current value unchanged. The extension you dial may ...
Page 335
Univerge sv8100 issue 11.0 class of service 2 - 303 5. Enter the night 1 mode class of service for the extension you selected in step 3 and press hold. You see: mode3:nn press hold to leave the current value unchanged. 6. Enter the midnight 1 mode class of service for the extension you selected in s...
Page 336
Issue 11.0 univerge sv8100 2 - 304 class of service this page intentionally left blank.
Page 337: Clock/calendar Display
Univerge sv8100 issue 11.0 clock/calendar display 2 - 305 clock/calendar display description the system uses clock/calendar display for: using the daylight savings setup program, you can determine whether the system should automatically adjust the system time for daylight savings time/standard time ...
Page 338
Issue 11.0 univerge sv8100 2 - 306 clock/calendar display system availability terminals all multiline terminals with display required component(s) none related features class of service night service single line telephones, analog 500/2500 sets vm8000 inmail voice mail integration (analog) guide to ...
Page 339
Univerge sv8100 issue 11.0 clock/calendar display 2 - 307 10-01-02 time and date – month enter two digits (01~12) for the month. 01~12 (default not assigned) 10-01-03 time and date – day enter two digits (01~31) for the day. 01~31 (default not assigned) 10-01-04 time and date – week enter the digit ...
Page 340
Issue 11.0 univerge sv8100 2 - 308 clock/calendar display operation the date must be set in system programming (10-01). To set the system time: 1. Press speaker. 2. Dial 728. 3. Dial two digits for the hour (24 hour clock, 13 = 1:00 pm). 4. Dial two digits for the minutes (00~59). 5. Press speaker t...
Page 341
Univerge sv8100 issue 11.0 co message waiting indication 2 - 309 co message waiting indication description this feature provides a message waiting indication when voice mail from the central office is used. The co provides this feature using visual message waiting indication (vmwi) standards. Visual...
Page 342
Issue 11.0 univerge sv8100 2 - 310 co message waiting indication default setting none system availability terminals all multiline terminals required component(s) cd-4cotb blade with pz-4cotf daughter board related features battery backup – system power message waiting speed dial – system/group/stati...
Page 343
Univerge sv8100 issue 11.0 co message waiting indication 2 - 311 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards f...
Page 344
Issue 11.0 univerge sv8100 2 - 312 co message waiting indication operation to program the co message waiting callback speed dial bin from an attendant position: 1. Press feature. 2. Dial 28. 3. Press the co line. 4. Dial speed dial bin (default = 1999). The valid range is 0000~1999 and depends on sy...
Page 345
Univerge sv8100 issue 11.0 co message waiting indication 2 - 313 to clear the central office – message waiting indication from an attendant position: 1. Press feature. 2. Dial 20. 3. Press the co line key..
Page 346
Issue 11.0 univerge sv8100 2 - 314 co message waiting indication this page intentionally left blank.
Page 347: Code Restriction
Univerge sv8100 issue 11.0 code restriction 2 - 315 code restriction description code restriction limits the numbers an extension user may dial. By allowing extensions to place only certain types of calls, you can better control long distance costs. The system applies code restriction according to t...
Page 348
Issue 11.0 univerge sv8100 2 - 316 code restriction restrict code table when you want code restriction to allow most calls and restrict only selected calls, use the restrict code table. To block only 1-900 calls, for example, enter 1900 in the restrict code table. (if the same code restriction class...
Page 349
Univerge sv8100 issue 11.0 code restriction 2 - 317 code call digit counting with code call digit counting, you can limit the number of digits long distance callers can dial. This lets you prevent callers from dialing extensively into long distance dial-up services. You can make four entries (4~30 d...
Page 350
Issue 11.0 univerge sv8100 2 - 318 code restriction each phone and trunk have a restriction class. The higher class applies for outgoing calls. For example: when trunk class is 01 and station class 02, toll restriction class 02 is applied. When trunk class is 15 and station class 03, toll restrictio...
Page 351
Univerge sv8100 issue 11.0 code restriction 2 - 319 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pr...
Page 352
Issue 11.0 univerge sv8100 2 - 320 code restriction 21-01-10 system options for outgoing calls – dial digits for toll restriction path if this option is programmed with an entry other than 0, a call does not have a talk path unless the user dials at least the number of digits entered in this option ...
Page 353
Univerge sv8100 issue 11.0 code restriction 2 - 321 21-05-02 toll restriction class – international call permit code table for the toll restriction class you select, assign or unassign the international call permit table (program 21-06-02). 0 = unassign 1 = assign default: 1, 3~15 = 0 2 = 1 21-05-04...
Page 354
Issue 11.0 univerge sv8100 2 - 322 code restriction 21-05-11 toll restriction class – intercom call restriction for the toll restriction class you select, enable or disable intercom call restriction. If enabled, extensions cannot place or receive intercom calls. 0 = disable 1 = enable (default = 0) ...
Page 355
Univerge sv8100 issue 11.0 code restriction 2 - 323 operation to place a trunk call if your system is code restricted: 1. Place call normally. If your code restriction class does not allow the number you dial, your call is cut off. 21-06-06 toll restriction table data setup – permit code table progr...
Page 356
Issue 11.0 univerge sv8100 2 - 324 code restriction this page intentionally left blank.
Page 357: Code Restriction Override
Univerge sv8100 issue 11.0 code restriction override 2 - 325 code restriction override description code restriction override lets a user temporarily bypass the code restriction for an extension. This helps a user that must place an important call that code restriction normally prevents. For example,...
Page 358
Issue 11.0 univerge sv8100 2 - 326 code restriction override code restriction station message detail recording voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are...
Page 359
Univerge sv8100 issue 11.0 code restriction override 2 - 327 21-14-02 walking toll restriction password setup – walking toll restriction class number enter the walking toll restriction class of service (1~15) to be used for each table number assigned in program 21-14-01. 1~15 (default = 1) 35-02-01 ...
Page 360
Issue 11.0 univerge sv8100 2 - 328 code restriction override 35-02-12 smdr output options – did table name output determine if the did table name should be displayed. 0 = not displayed 1 = displayed (default = 0) 35-02-13 smdr output options – cli output when did to trunk determine if the cli output...
Page 361
Univerge sv8100 issue 11.0 code restriction override 2 - 329 walking code restriction 663?.
Page 362
Issue 11.0 univerge sv8100 2 - 330 code restriction override temporary code restriction override service code 663 be changed 775?.
Page 363
Univerge sv8100 issue 11.0 code restriction override 2 - 331 operation to temporarily override a restricted extension code restriction: you can override restriction for only one call at a time. 1. At the multiline terminal, press speaker. - or - at single line telephone, lift the handset. 2. Dial 77...
Page 364
Issue 11.0 univerge sv8100 2 - 332 code restriction override this page intentionally left blank.
Page 365: Code Restriction, Dial Block
Univerge sv8100 issue 11.0 code restriction, dial block 2 - 333 code restriction, dial block description code restriction, dial block lets a user temporarily block dialing on an extension. This helps a user block his or her phone from being used by another person while they are away from their desk....
Page 366
Issue 11.0 univerge sv8100 2 - 334 code restriction, dial block related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro...
Page 367
Univerge sv8100 issue 11.0 code restriction, dial block 2 - 335 operation to set dial block: 1. At the multiline terminal, press speaker. - or - at the single line telephone, lift the handset. 2. Dial 600 (default). 3. Dial the 4-digit dial block code (as set in programming). 4. Dial 1. Confirmation...
Page 368
Issue 11.0 univerge sv8100 2 - 336 code restriction, dial block to set dial block from another extension: 1. At the multiline terminal, press speaker. - or - at the single line telephone, lift the handset. 2. Dial 601 (default). 3. Dial the 4-digit dial block code (as set in programming). 4. Dial th...
Page 369: Conference
Univerge sv8100 issue 11.0 conference 2 - 337 conference description conference lets an extension user add additional inside and outside callers to their conversation. With conference, a user can set up a multiple-party telephone meeting without leaving the office. The cd-cp00-us provides 64 confere...
Page 370
Issue 11.0 univerge sv8100 2 - 338 conference an option is available which allows an extension conf key (sc 751: 07) to be programmed for conference or for transfer. When set for transfer, the user places a call on hold, dials the extension to which it should be transferred, and presses conf. The ca...
Page 371
Univerge sv8100 issue 11.0 conference 2 - 339 required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used w...
Page 372
Issue 11.0 univerge sv8100 2 - 340 conference 15-02-24 multiline telephone basic data setup – conference key mode allow an extension conf key to be programmed for conference or for transfer. When set for transfer, the user places a call on hold, dials the extension to which it should be transferred,...
Page 373
Univerge sv8100 issue 11.0 conference 2 - 341 operation to establish a conference: multiline terminal 1. Establish intercom or trunk call. 2. Press conf or conf softkey (program 15-07 or sc 751: 07). 3. Dial the extension you want to add. - or - access outside call. - or - retrieve call from park or...
Page 374
Issue 11.0 univerge sv8100 2 - 342 conference single line telephone 1. Establish intercom or trunk call. 2. Hookflash and dial # 1. 3. Dial extension you want to add. - or - access trunk call. - or - retrieve call from park orbit. 4. Hookflash and repeat step 3 to add more parties. - or - hookflash ...
Page 375
Univerge sv8100 issue 11.0 conference 2 - 343 to exit a conference with internal and outside conference members without affecting the other parties: multiline terminal 1. Hang up. If you press hold while on a call with two outside callers, the outside callers hear what is programmed in program 10-04...
Page 376
Issue 11.0 univerge sv8100 2 - 344 conference the following steps are not available for disa or tie line trunks: 1. Dial the extension number of the internal party. 2. Dial the single digit service code, if programmed. Instead of the single digit service code, the service code 710 can also be dialed...
Page 377
Univerge sv8100 issue 11.0 conference, voice call/privacy release 2 - 345 conference, voice call/privacy release description voice call conference lets extension users in the same work area join in a trunk conference. To initiate a voice call conference, an extension user just presses the meet-me co...
Page 378
Issue 11.0 univerge sv8100 2 - 346 conference, voice call/privacy release system availability terminals all multiline terminals required component(s) none related features caller id conference programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate t...
Page 379
Univerge sv8100 issue 11.0 conference, voice call/privacy release 2 - 347 operation to join a voice call conference (if invited): 1. After conference request, press indicated line key. A conf indication is displayed on both telephones. A trunk with privacy release or voice call conference blinks. To...
Page 380
Issue 11.0 univerge sv8100 2 - 348 conference, voice call/privacy release to toggle between private and non-private mode: 1. Press the meet-me conference key (program 15-07-01, sc 751: 32). - or - press the trunk line key. (this toggles from non-private to private. To go back to non-private, the mee...
Page 381: Continued Dialing
Univerge sv8100 issue 11.0 continued dialing 2 - 349 continued dialing description continued dialing allows an extension user to dial a call, wait for the called party to answer, and then dial additional digits. This helps users that need services like voice mail, automatic banking and other common ...
Page 382
Issue 11.0 univerge sv8100 2 - 350 continued dialing default setting enabled system availability terminals all multiline terminals required component(s) none related features pulse to tone conversion guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are...
Page 383
Univerge sv8100 issue 11.0 continued dialing 2 - 351 operation to use continued dialing: 1. Place an intercom or trunk call. 2. Continue dialing after the call connects. Toll restriction and class of service programming may limit continued dialing. 20-06-01 class of service for extensions assign a c...
Page 384
Issue 11.0 univerge sv8100 2 - 352 continued dialing this page intentionally left blank.
Page 385: Cordless Dect Terminals
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 353 cordless dect terminals description the cordless dect terminals may be used with the univerge sv8100 kts. The dtl-8r-1 tel uses 1.9 ghz dect 6.0 fm technology and is connected in tandem to a multiline terminal. The itl-8r-1 tel uses 1.9 ghz ...
Page 386
Issue 11.0 univerge sv8100 2 - 354 cordless dect terminals conditions the itl-8r-1 does not support the manual or automatic registration modes to the sv8100. The itl-8r-1 does support the plug and play registration mode to the sv8100. If using the base switching option, cordless dect terminal progra...
Page 387
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 355 under certain conditions, hold and transfer have the same behavior. To prevent an unwanted transfer after placing a call on hold and calling another user, the line key for the call on hold must be pressed to retrieve the call from hold, othe...
Page 388
Issue 11.0 univerge sv8100 2 - 356 cordless dect terminals system availability terminals dtl-8r-1 tel itl-8r-1 tel required component(s) cd-8dlca blade with pz-8dlcb daughter board cd-cp00-us with pz-32/64/128ipla or pz-32/64/128iplb daughter board sip telephone licenses -or- cd-16dlca related featu...
Page 389
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 357 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for fea...
Page 390
Issue 11.0 univerge sv8100 2 - 358 cordless dect terminals 10-03-04 etu setup (dlca pkg setup) – optional installed unit 1 (only applies to dth/dtr telephones) use to setup and confirm the basic configuration data for optional installed unit 1. 0 = none 1 = apr module 2 = apa module 3 = ada module 4...
Page 391
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 359 10-03-10 etu setup (dlca pkg setup) – bottom option information (only applies to dtl style telephones) shows optional adapter information. 0 = no option 1 = apr 2 = ada 3 = bha (default = 0) 10-03-11 etu setup (dlca pkg setup) – handset opti...
Page 392
Issue 11.0 univerge sv8100 2 - 360 cordless dect terminals 20-07-13 class of service options (administrator level) – vrs record (vrs msg operation) turn off or on an extension user ability to record, erase and listen to vrs messages. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for cos 15)...
Page 393
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 361 20-07-25 class of service options (administrator level) – set/ cancel caller id refuse enable/disable an extension user ability to set or cancel caller id refuse. 0 = off 1 = on (default = 0 for cos 1~15) 20-07-26 class of service options (a...
Page 394
Issue 11.0 univerge sv8100 2 - 362 cordless dect terminals 20-08-10 class of service options (outgoing call service) – signal/ voice call turn off or on an extension allowing it to force handsfree answerback or forced intercom ringing for outgoing intercom calls. 0 = off 1 = on (default = 1 for cos ...
Page 395
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 363 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m override turns off or on the extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, the d...
Page 396
Issue 11.0 univerge sv8100 2 - 364 cordless dect terminals 20-10-01 class of service options (answer service) – group call pickup (within group) turn off or on group call pickup for calls ringing an extension pickup group as well as ring group calls (service code # ). 0 = off 1 = on (default = 1 f...
Page 397
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 365 20-11-02 class of service options (hold/ transfer service) – call forward when busy turn off or on an extension user ability to set call forwarding when busy. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-03 class of service options (hold/...
Page 398
Issue 11.0 univerge sv8100 2 - 366 cordless dect terminals 20-11-13 class of service options (hold/ transfer service) – operator transfer after hold callback turn off or on an extension ability to have a call which recalls from hold transfer to the operator. 0 = off 1 = on (default = 0 for cos 1~15)...
Page 399
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 367 20-11-23 class of service options (hold/ transfer service) – car/ve call forward set/cancel turn off or on an extension user ability to set and cancel call forwarding for a car or virtual extension. 0 = off 1 = on (default = 1 for cos 1~15) ...
Page 400
Issue 11.0 univerge sv8100 2 - 368 cordless dect terminals 20-13-10 class of service options (supplementary service) – barge-in monitor enable the barge-in speech mode) or monitor mode at the initiating extension (i.E., barge-in initiator). 0 = speech 1 = monitor (default = 0 for cos 1~15) 20-13-11 ...
Page 401
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 369 20-13-20 class of service options (supplementary service) – account code/toll restriction operator alert (restricted operation transfer) turn off or on operator alert when an extension improperly enters an account code or violates toll restr...
Page 402
Issue 11.0 univerge sv8100 2 - 370 cordless dect terminals 20-13-31 class of service options (supplementary service) – connected line identification (colp) define the supplementary feature availability for each extension class of service (cos). 0 = off 1 = on (default = 0 for cos 1~15) 20-13-32 clas...
Page 403
Univerge sv8100 issue 11.0 cordless dect terminals 2 - 371 operation to set up and program the cordless dect terminals (dtl-8r-1): 1. Press and hold down and # , then press talk. The f1 led flashes red and f1=lk01 is displayed on the lcd. 2. Press ring/vol repeatedly to scroll through the line key (...
Page 404
Issue 11.0 univerge sv8100 2 - 372 cordless dect terminals 3. Press on/offmute to select the displayed line key or feature. 4. When a line key is assigned, press mute once to enter the off-hook ringing on or off mode. Press ring/vol to toggle between talk for on or no talk for off. Talk is selected ...
Page 405
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 373 cordless telephone connection description using an ap(r)-r/ap(a)-r unit for dth/dtr telephones or an apr-l for dtl telephones a cordless telephone (2500-type) can be connected to a multiline terminal. The cd-4lca with pz-4lca daughter ...
Page 406
Issue 11.0 univerge sv8100 2 - 374 cordless telephone connection the following features are supported by an apr-l ap(r)-r or ap(a)-r: initiate conference change station name privacy release by pressing line key group listen dss/blf indication headset ringing the apr-l ap(r)-r and ap(a)-r only suppor...
Page 407
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 375 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards f...
Page 408
Issue 11.0 univerge sv8100 2 - 376 cordless telephone connection 10-03-04 etu setup (dlca pkg setup) – optional installed unit 1 (only applies to dth/dtr telephones) use to setup and confirm the basic configuration data for optional installed unit 1. 0 = none 1 = apr module 2 = apa module 3 = ada mo...
Page 409
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 377 10-03-10 etu setup (dlca pkg setup) – bottom option information (only applies to dtl style telephones) shows optional adapter information. 0 = no option 1 = apr 2 = ada 3 = bha (default = 0) 10-03-11 etu setup (dlca pkg setup) – handse...
Page 410
Issue 11.0 univerge sv8100 2 - 378 cordless telephone connection 20-07-12 class of service options (administrator level) – trunk port disable turn off or on an extension user ability to use the trunk port disable feature. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for cos 15) 20-07-13 cl...
Page 411
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 379 20-07-25 class of service options (administrator level) – set/ cancel caller id refuse enable/disable an extension user ability to set or cancel caller id refuse. 0 = off 1 = on (default = 0 for cos 1~15) 20-07-26 class of service opti...
Page 412
Issue 11.0 univerge sv8100 2 - 380 cordless telephone connection 20-08-11 class of service options (outgoing call service) – protect for the call mode switching from caller when an extension is set to ring mode for icm calls, enabling this option prevents callers from changing the call to voice anno...
Page 413
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 381 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m override turn off or on the extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, ...
Page 414
Issue 11.0 univerge sv8100 2 - 382 cordless telephone connection 20-10-06 class of service options (answer service) – meet-me conference and paging turn off or on an extension user ability to use meet-me conference and paging. 0 = off 1 = on (default = 1 for cos 1~15) 20-10-07 class of service optio...
Page 415
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 383 20-11-09 class of service options (hold/ transfer service) – group hold initiate turn off or on an extension user ability to initiate a group hold. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-10 class of service options (hold/ tran...
Page 416
Issue 11.0 univerge sv8100 2 - 384 cordless telephone connection 20-11-20 class of service options (hold/ transfer service) – no callback turn off or on an extension ability to receive callbacks. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-21 class of service options (hold/ transfer service) – r...
Page 417
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 385 20-13-05 class of service options (supplementary service) – intercom off-hook signaling turn off or on the ability of an extension to receive off-hook signals. 0 = off 1 = on (default = 1 for cos 1~15) 20-13-06 class of service options...
Page 418
Issue 11.0 univerge sv8100 2 - 386 cordless telephone connection 20-13-20 class of service options (supplementary service) – account code/toll restriction operator alert (restricted operation transfer) turn off or on operator alert when an extension improperly enters an account code or violates toll...
Page 419
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 387 20-13-30 class of service options (supplementary service) – background music allow/deny an extension user to turn background music on and off. This applies only to the multiline terminal. 0 = deny 1 = allow (default = 1 for cos 1~15) 2...
Page 420
Issue 11.0 univerge sv8100 2 - 388 cordless telephone connection operation to make a call using a cordless single line telephone: 1. Go off-hook. 2. Dial the station number or dial the trunk access code and telephone number. To answer a call using a cordless single line telephone: when the multiline...
Page 421
Univerge sv8100 issue 11.0 cordless telephone connection 2 - 389 to transfer a call from a multiline terminal to its associated cordless single line telephone: 1. The single line telephone user goes off-hook (at this time, the call is automatically connected to the single line telephone). 2. The mul...
Page 422
Issue 11.0 univerge sv8100 2 - 390 cordless telephone connection this page intentionally left blank.
Page 423: Data Line Security
Data line security 2 - 391 d data line security description data line security protects any station port from receiving audible tones (such as camp-on or override) and denies a station from barging in while busy to prevent disruption of data transmission when using a modem or facsimile machine. Cond...
Page 424
Issue 11.0 univerge sv8100 2 - 392 data line security guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature ...
Page 425: Delayed Ringing
Univerge sv8100 issue 11.0 delayed ringing 2 - 393 delayed ringing description delayed ringing allows programmed secondary answering positions to ring on incoming calls after a programmed time. This feature applies to co/pbx lines, secondary incoming extensions, virtual extensions, and call arrival ...
Page 426
Issue 11.0 univerge sv8100 2 - 394 delayed ringing virtual extensions guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wiza...
Page 427
Univerge sv8100 issue 11.0 delayed ringing 2 - 395 15-07-01 programmable function keys assign car/sie/ve function keys (code 03 + extension number) or co function keys (code 01 + trunk port) on multiline terminals. Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance functi...
Page 428
Issue 11.0 univerge sv8100 2 - 396 delayed ringing operation to answer delay ringing calls: 1. Go off-hook. - or - press answer. - or - press the flashing key. Either trunk key or car/sie/ve key. To program a car/sie/ve key on a phone: 1. Press speaker. 2. Dial 752. 3. Press the key you want to prog...
Page 429
Univerge sv8100 issue 11.0 delayed ringing 2 - 397 9. Dial the mode number in which the key delay rings. 1 = day 1 2 = night 1 3 = midnight 1 4 = rest 1 5 = day 2 6 = night 2 7 = midnight 2 8 = rest 2 10. Press speaker..
Page 430
Issue 11.0 univerge sv8100 2 - 398 delayed ringing this page intentionally left blank.
Page 431: Department Calling
Univerge sv8100 issue 11.0 department calling 2 - 399 department calling description with department calling, an extension user can call an idle extension in a programmed department group (64 department groups available) by dialing the group pilot number. For example, this would let a caller dial th...
Page 432
Issue 11.0 univerge sv8100 2 - 400 department calling delay: this feature can be enabled or disabled by using a (59) key programmed in program 15-07. It can also be done by using service codes assigned in program 11-11-28 (set) and program 11-11-29 (cancel). When this feature is activated, any did c...
Page 433
Univerge sv8100 issue 11.0 department calling 2 - 401 if all members of the department group are busy, an incoming or transferred call to the group pilot number queues for an available member. Each group has a queue that can hold any number of waiting calls. If a display telephone is waiting in queu...
Page 434
Issue 11.0 univerge sv8100 2 - 402 department calling when a department group is assigned as the vm department group in program 45-01-01 it only works as priority mode no matter what program 16-01-02 is set to for that department group. Program 16-01-05 (extension group all ring mode operation) does...
Page 435
Univerge sv8100 issue 11.0 department calling 2 - 403 circular routing system availability terminals all terminals figure 2-3 department calling circular routing call 1 call 2 call 3 call 4.
Page 436
Issue 11.0 univerge sv8100 2 - 404 department calling required component(s) vrs for messaging related features call arrival (car) keys call forwarding department step calling transfer vm8000 inmail voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indi...
Page 437
Univerge sv8100 issue 11.0 department calling 2 - 405 11-11-27 service code setup (for setup/ entry operation) – destination of automatic transfer each extension group set the service code for setting the destination for immediate automatic transfer for icm and transferred calls to department groups...
Page 438
Issue 11.0 univerge sv8100 2 - 406 department calling 16-01-03 department group basic data setup – department routing when busy (auto step call) set how the system routes an intercom call to a busy department group member. The caller can hear busy tone (0) or overflow to the first available departme...
Page 439
Univerge sv8100 issue 11.0 department calling 2 - 407 16-02-01 department group assignment for extensions set up the department group called by the pilot number and the extension priority when a group is called. Call pickup groups are set up in 23-02. Department groups 1~64 priority 1~999 default = ...
Page 440
Issue 11.0 univerge sv8100 2 - 408 department calling operation to call a department group: 1. Go off-hook. 2. Dial department extension number. The system routes the call to the first free telephone in the department group. 3. Optional: to manually ring all members of the group, dial the single dig...
Page 441
Univerge sv8100 issue 11.0 department calling 2 - 409 to log out of your department calling group: while you are logged out, department calling cannot route calls to your extension. 1. Press speaker 2. Dial 650 + 1. - or - press department calling log in key (program 15-07-01 or sc 751: 46). The key...
Page 442
Issue 11.0 univerge sv8100 2 - 410 department calling this page intentionally left blank.
Page 443: Department Step Calling
Univerge sv8100 issue 11.0 department step calling 2 - 411 department step calling description after calling a busy department calling group member, an extension user can have department step calling quickly call another member in the group. The caller does not have to hang up and place another inte...
Page 444
Issue 11.0 univerge sv8100 2 - 412 department step calling guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for fea...
Page 445
Univerge sv8100 issue 11.0 department step calling 2 - 413 operation to make a step call: 1. Place a call to a busy department group member. - or - place a call to a department group pilot number. 2. Dial department step code (2) to call the next available department group member. 3. Repeat step 2 t...
Page 446
Issue 11.0 univerge sv8100 2 - 414 department step calling this page intentionally left blank.
Page 447: Dial Pad Confirmation Tone
Univerge sv8100 issue 11.0 dial pad confirmation tone 2 - 415 dial pad confirmation tone description for an extension with dial pad confirmation tone enabled, the user hears a beep each time they press a key. This is helpful for intercom calls and dial pulse trunk calls, since these calls provide no...
Page 448
Issue 11.0 univerge sv8100 2 - 416 dial pad confirmation tone guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for ...
Page 449: Dial Tone Detection
Univerge sv8100 issue 11.0 dial tone detection 2 - 417 dial tone detection description if a trunk has dial tone detection enabled, the system monitors for dial tone from the telco or pbx when a user places a call on that trunk. If the user accesses the trunk directly (by pressing a line key or diali...
Page 450
Issue 11.0 univerge sv8100 2 - 418 dial tone detection last number redial save number dialed speed dial – system/group/station t1 trunking (with ani/dnis compatibility) trunk group routing trunk groups guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that a...
Page 451
Univerge sv8100 issue 11.0 dial tone detection 2 - 419 14-02-11 analog trunk data setup – next trunk in rotary if no dial tone if enabled, the system skips over a trunk if dial tone is not detected. This option pertains to calls placed using call appearance (cap) keys, speed dial, ars, last number r...
Page 452
Issue 11.0 univerge sv8100 2 - 420 dial tone detection operation dial tone detection is automatic if enabled in programming. Table 2-10 dial tone detection program interaction method 14-02-05 14-02-11 result if dial tone not present . . . Press a line key - or - dial #9+ trunk number 0 0 trunk hangs...
Page 453: Dialing Number Preview
Univerge sv8100 issue 11.0 dialing number preview 2 - 421 dialing number preview description dialing number preview lets a display multiline terminal user dial and review a number before the system dials it. Dialing number preview helps the user avoid dialing errors. Conditions an extension user can...
Page 454
Issue 11.0 univerge sv8100 2 - 422 dialing number preview related features central office calls, placing voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most ...
Page 455
Univerge sv8100 issue 11.0 dialing number preview 2 - 423 3. To preview any number, dial the number you want to call. To preview a speed dial – system/group number, press redial and dial the speed dial – system/group bin number you want to call. The number is displayed. 4. To dial out the displayed ...
Page 456
Issue 11.0 univerge sv8100 2 - 424 dialing number preview this page intentionally left blank.
Page 457: Digital Trunk Clocking
Univerge sv8100 issue 11.0 digital trunk clocking 2 - 425 digital trunk clocking description the univerge sv8100 cd-cp00-us has a built-in clock source for all digital trunk blades. Digital trunk blades are connected via an internal plo (phase locked oscillator) to derive primary clock from the netw...
Page 458
Issue 11.0 univerge sv8100 2 - 426 digital trunk clocking system availability terminals none required component(s) cd-cp00-us cd-2bria -or- cd-prta, cd-ccta related features isdn compatibility k-ccis – t1 t1 trunking (with ani/dnis compatibility) feature examples digital trunk clocking examples: if ...
Page 459
Univerge sv8100 issue 11.0 digital trunk clocking 2 - 427 if there are multiple pris and the one being used for the source goes down, the system begins to count forward in slot numbers looking for the next available pri. In this example, the pri in 02 went down, so the system now begins looking forw...
Page 460
Issue 11.0 univerge sv8100 2 - 428 digital trunk clocking in this example, there are multiple t1 circuits and a bri circuit. Since the t1 assigned as external has higher priority than a bri, the t1 external is the plo synchronization source. In this example, there is a pri, multiple t1s, and a bri. ...
Page 461
Univerge sv8100 issue 11.0 digital trunk clocking 2 - 429 in this scenario, the pri was the clocking source until it went down. There are no other pris, t1 (externals), or bris in the system. The cd-cp00-us now becomes the plo synchronization source. Guide to feature programming refer to the related...
Page 462
Issue 11.0 univerge sv8100 2 - 430 digital trunk clocking this page intentionally left blank.
Page 463: Direct Inward Dialing (Did)
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 431 direct inward dialing (did) description direct inward dialing (did) lets outside callers directly dial system extensions. Did saves time for callers who know the extension number they wish to reach. To place a did call, the outside calle...
Page 464
Issue 11.0 univerge sv8100 2 - 432 direct inward dialing (did) in addition to number conversion, each did translation table entry can have a name assigned to it. When the did call rings the destination extension, the programmed name is displayed. Flexible did service compatibility with three-digit s...
Page 465
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 433 smdr includes dialed number the smdr report can optionally print the trunk name (entered in system programming) or the number the incoming caller dialed (i.E., the dialed did digits). This allows you to analyze the smdr report based on t...
Page 466
Issue 11.0 univerge sv8100 2 - 434 direct inward dialing (did) did intercept destination for each did number with this feature the system allows you to program a did intercept destination for a did number which receives no answer or busy call. The system can be programmed to use a trunk ring group, ...
Page 467
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 435 did call by time schedule did call by time schedule allows for 100 (version 6000 or lower) or 500 (version 7000 or higher) programmed did conversion table entries (program 22-17-01) that can be routed based on time patterns. Each did con...
Page 468
Issue 11.0 univerge sv8100 2 - 436 direct inward dialing (did) did call by day of week schedule (version 7000 or higher) did call by weekly schedule allows for 500 programmed did conversion table entries (program 22-17-01 and program 22-17-05) that can be routed based on day of week patterns. Each d...
Page 469
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 437 program 22-11-01 and program 22-11-02 table no. Receive dial transfer dial 1 none 101 2 none 102 3 none 103 4 none 300 example 2 (saturday) example 3 (sunday).
Page 470
Issue 11.0 univerge sv8100 2 - 438 direct inward dialing (did) federal communications commission did requirements allowing this equipment to operate without providing proper answer supervision signaling violates part 68 rules. This equipment returns answer supervision to the public switched telephon...
Page 471
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 439 this equipment returns answer supervision on all did calls forwarded back to the public switched telephone network. Permissible exceptions are when: a call is unanswered. A busy tone is received. A reorder tone is received. When ordering...
Page 472
Issue 11.0 univerge sv8100 2 - 440 direct inward dialing (did) transferred calls on disa, did, dil, isdn trunks, or from the vrs can display the reason a call is being transferred (call forward, busy, no answer, or dnd). When defining trunks as did or did mode in program 22-02-01, did translation (p...
Page 473
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 441 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for...
Page 474
Issue 11.0 univerge sv8100 2 - 442 direct inward dialing (did) 15-07-01 programmable function keys assign line or call appearance (cap) keys for did trunks (trunks: 1~200). Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 20-06...
Page 475
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 443 22-02-01 incoming call trunk setup for each night service mode, enter service type 3 when the trunk should be a did trunk. Trunks 1~200 0 = normal 1 = vrs (second dial tone if no vrs installed) 2 = disa 3 = did 4 = dil 5 = e&m tie line 6...
Page 476
Issue 11.0 univerge sv8100 2 - 444 direct inward dialing (did) 22-11-01 did translation number conversion – received number for each did translation table entry (1~2000), specify the digits received by the system. Maximum eight digits (default not assigned) 22-11-02 did translation number conversion...
Page 477
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 445 22-11-09 did translation number conversion – music on hold source for each did translation table entry (1~2000), specify the source of music to be used for did trunks. 0 = ic/moh port 1 = bgm port 2 = aci port (default = 0) 22-11-10 did ...
Page 478
Issue 11.0 univerge sv8100 2 - 446 direct inward dialing (did) 25-01-01 vrs/disa line basic data setup – vrs/disa dial-in mode determine whether the system should use option 0 or option 1 (use dial conversion table) for calls. 0 = extension number service code specify (intercom) 1 = use dial convers...
Page 479
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 447 25-04-01 vrs/disa transfer ring group with no answer/busy for each trunk port (001~200), set the operating mode of each disa trunk. This sets what happens to the call when the disa or automated attendant caller calls a busy or unanswered...
Page 480
Issue 11.0 univerge sv8100 2 - 448 direct inward dialing (did) 25-07-02 system timers for vrs/disa – vrs/disa no answer time a vrs/disa caller can ring an extension for this time before the system sets the call as a ring no answer. After this time expires, the call follows the programmed ring no ans...
Page 481
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 449 direct call by time schedule: program number program name description/comments assigned data level 1 2 3 11-10-35 service code setup (for administrator) – dial-in mode switching assign the service code dial-in mode switching. Mlt, slt (d...
Page 482
Issue 11.0 univerge sv8100 2 - 450 direct inward dialing (did) operation did calls ring extensions like normal trunk calls. To activate did call by time schedule: 1. At any display multiline terminal, press speaker. 2. Dial the dial-in mode switching service code (default = not assigned). - or - pre...
Page 483
Univerge sv8100 issue 11.0 direct inward dialing (did) 2 - 451 4. Dial the time pattern 1~8. Table 2-15 led flash patterns time pattern led appearance pattern 1 off pattern 2 on pattern 3 slow flash pattern 4 fast flash patterns 5~8 off.
Page 484
Issue 11.0 univerge sv8100 2 - 452 direct inward dialing (did) this page intentionally left blank.
Page 485: Direct Inward Line (Dil)
Univerge sv8100 issue 11.0 direct inward line (dil) 2 - 453 direct inward line (dil) description a direct inward line (dil) is a trunk that rings an extension, virtual extension or department group directly. Since dils only ring one extension or group (i.E., the dil destination), employees always kn...
Page 486
Issue 11.0 univerge sv8100 2 - 454 direct inward line (dil) program a name for a dil in program 14-01-01. This makes it easier to identify the incoming call. If a multiline terminal is busy, a second incoming dil call provides call alert notification, depending on chassis programming. The second dil...
Page 487
Univerge sv8100 issue 11.0 direct inward line (dil) 2 - 455 group call pickup name storing off-hook signaling paging, external programmable function keys ring groups transfer guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programmin...
Page 488
Issue 11.0 univerge sv8100 2 - 456 direct inward line (dil) 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m override turn off or on an extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, the de...
Page 489
Univerge sv8100 issue 11.0 direct inward line (dil) 2 - 457 operation to answer a call on your direct inward line: 1. Lift the handset. 2. Press the flashing line key for dil on the multiline terminal. Press the flashing answer key to put the first call on hold and answer the second incoming call. T...
Page 490
Issue 11.0 univerge sv8100 2 - 458 direct inward line (dil) this page intentionally left blank.
Page 491
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 459 direct inward system access (disa) description disa permits outside callers to directly dial system extensions, trunks and selected features. This could help an employee away from the office that wants to directly dial co-workers ...
Page 492
Issue 11.0 univerge sv8100 2 - 460 direct inward system access (disa) disa class of service disa class of service provides features and dialing restrictions for disa callers. This allows you to control the ability of the disa callers dialing into your system. When a disa caller first accesses the sy...
Page 493
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 461 disa/tie trunk barge-in the disa/tie trunk barge-in option allows a disa/tie line caller to break into another extension user’s established call. This sets up a three-way conversation between the intruding party and the two partie...
Page 494
Issue 11.0 univerge sv8100 2 - 462 direct inward system access (disa) program 20-28-02: no setting program 20-28-03: 180 program 24-02-07: 600 (used only with manually transferred tandem trunk calls) program 24-02-10: 30 (used only with manually transferred tandem trunk calls) program 25-07-07: 600 ...
Page 495
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 463 department calling with overflow message requires a dsp daughter board for vrs. Disa can only be set to call forward to another extension. Call forward off-premise is not supported. When the disa/vrs ring group transfer (programs ...
Page 496
Issue 11.0 univerge sv8100 2 - 464 direct inward system access (disa) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wiza...
Page 497
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 465 14-01-13 basic trunk data setup – trunk-to-trunk transfer if disa caller can place outgoing calls through the system (refer to program 20-14 in the electra elite ipk ii programming manual), enable loop supervision for the disa tru...
Page 498
Issue 11.0 univerge sv8100 2 - 466 direct inward system access (disa) 20-14-02 class of service options for disa/e&m – trunk group routing/ars access enable/disable a disa or tie trunk caller ability to dial 9 for trunk group routing or automatic route selection (ars). 0 = off 1 = on (default = 1 fo...
Page 499
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 467 21-15-01 individual trunk group routing for extensions designate the trunk route accessed when a user dials the alternate trunk route access code. Refer to trunk group routing to set up outbound routing. 0~100 (0 = no setting) (de...
Page 500
Issue 11.0 univerge sv8100 2 - 468 direct inward system access (disa) 25-02-01 did/disa vrs message assign the source and vrs message number to be used as the automated attendant message for each trunk (001~200) which is assigned as a vrs/disa. 0 = no message 1 = vrs (01~100 vrs message number) 2 = ...
Page 501
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 469 25-05-01 vrs/disa error message assignment assign the vrs message number to be used as the automated attendant error message. For each vrs/disa trunk that the vrs answers, enter the vrs message (1~100) the outside caller hears if ...
Page 502
Issue 11.0 univerge sv8100 2 - 470 direct inward system access (disa) 25-06-02 vrs/disa one-digit code attendant setup – destination number set up single digit dialing for automated attendant callers. For each vrs message programmed to answer outside calls, specify: the digit the automated attendant...
Page 503
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 471 25-07-07 system timers for vrs/disa – long conversation warning tone time determine the time a disa caller or any automatically transferred trunk-to-trunk (such as tandem trunking) conversation can talk before the long conversatio...
Page 504
Issue 11.0 univerge sv8100 2 - 472 direct inward system access (disa) 25-10-01 trunk group routing for disa assign the trunk group route chosen when a user places a disa call to the system and dials 9. Set trunk group routing in program 14-06. Enable or disable disa caller ability to dial 9 in progr...
Page 505
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 473 trunk continue/disconnect codes: program number program name description/comments assigned data level 1 2 3 14-01-25 basic trunk data setup – continued/discontinued trunk-to-trunk conversation when program 24-02-10 is set to disco...
Page 506
Issue 11.0 univerge sv8100 2 - 474 direct inward system access (disa) 24-02-07 system options for transfer – trunk-to-trunk transfer release warning tone this timer starts when a trunk begins talking with another trunk (for example: trunk-to-trunk transfer/tandem trunking). When this time expires, a...
Page 507
Univerge sv8100 issue 11.0 direct inward system access (disa) 2 - 475 operation to place a disa call into the system (from any 2500 type telephone): 1. Dial the telephone number that rings the disa trunk. 2. Wait for the disa trunk to automatically answer with a unique dial tone. 3. Dial the 6-digit...
Page 508
Issue 11.0 univerge sv8100 2 - 476 direct inward system access (disa) dial 703 + an external paging zone number (1~8 or 0 for all call). - or - dial 710 + a busy extension number to barge in to a call. To forward extension calls using a disa call into the system (from any 2500 type telephone): 1. Di...
Page 509
Univerge sv8100 issue 11.0 direct station selection (dss) console 2 - 477 direct station selection (dss) console description the dss console gives a multiline terminal user a busy lamp field (blf) and one-button access to extensions, trunks, and system features. This saves time for users that do a l...
Page 510
Issue 11.0 univerge sv8100 2 - 478 direct station selection (dss) console conditions changing flash patterns for dss consoles also changes them for hotline keys. When installing a dss, the system must auto-detect the console for the leds to function correctly. When connecting the dss to an extension...
Page 511
Univerge sv8100 issue 11.0 direct station selection (dss) console 2 - 479 when a multiline terminal user is on a call, they can transfer to another station by pressing a dss key for that station. It is not necessary to press transfer to transfer to another station using a dss key. When a multiline t...
Page 512
Issue 11.0 univerge sv8100 2 - 480 direct station selection (dss) console related features automatic call distribution (acd) call forwarding central office calls, answering central office calls, placing door box night service one-touch calling paging, external paging, internal programmable function ...
Page 513
Univerge sv8100 issue 11.0 direct station selection (dss) console 2 - 481 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro ...
Page 514
Issue 11.0 univerge sv8100 2 - 482 direct station selection (dss) console 20-13-49 class of service options (supplementary service) – blf indication on co incoming state determine if a blf of the station lights when a normal co call is ringing the phone. 0 = off 1 = on (default = 0 for cos 1~15) 20-...
Page 515
Univerge sv8100 issue 11.0 direct station selection (dss) console 2 - 483 30-05-06 dss console lamp table – acd agent log out (acd dss) define the led patterns for acd agents that are logged out on the dss consoles. 0~7 [default = 5 (il)] 30-05-07 dss console lamp table – acd agent log in (acd dss) ...
Page 516
Issue 11.0 univerge sv8100 2 - 484 direct station selection (dss) console operation calling an extension from your dss console: 1. Press the dss console key. If the call voice-announces, you can make it ring by dialing 1. If you do not have handsfree, you must lift the handset to speak. Answering a ...
Page 517
Univerge sv8100 issue 11.0 direct station selection (dss) console 2 - 485 4. (optional) announce the call. If called party does not want the call, press the flashing line key to retrieve it. Making an external page using your dss console: 1. Press the dss console external page zone key (1~8). If the...
Page 518
Issue 11.0 univerge sv8100 2 - 486 direct station selection (dss) console using a dss console key as a one-touch or programmable function key: a user can have dss console keys programmed as one-touch keys. These keys can be used for direct station selection, trunk calling, personal speed dial, speed...
Page 519: Directed Call Pickup
Univerge sv8100 issue 11.0 directed call pickup 2 - 487 directed call pickup description directed call pickup permits an extension user to intercept a call ringing another extension. This allows a user to conveniently answer a call for a co-worker from their own telephone. With directed call pickup,...
Page 520
Issue 11.0 univerge sv8100 2 - 488 directed call pickup related features call arrival (car) keys department calling group call pickup hold hotline park secretary call pickup secondary incoming extension transfer virtual extensions vm8000 inmail guide to feature programming the level 1, level 2 and l...
Page 521
Univerge sv8100 issue 11.0 directed call pickup 2 - 489 operation to use directed call pickup to intercept a call to a co-worker’s extension: 1. Pick up the handset or press speaker. 2. Dial . 3. Dial number of extension whose call you want to intercept. If more than one call is coming in, the syste...
Page 522
Issue 11.0 univerge sv8100 2 - 490 directed call pickup this page intentionally left blank.
Page 523: Directory Dialing
Univerge sv8100 issue 11.0 directory dialing 2 - 491 directory dialing description directory dialing allows a multiline terminal user to select a co-worker or outside caller from a list of names, rather than dialing the telephone number. Four types of directory dialing are available: spd – speed dia...
Page 524
Issue 11.0 univerge sv8100 2 - 492 directory dialing system availability terminals all multiline terminals with display and softkeys required component(s) none related features last number redial name storing speed dial – system/group/station softkeys guide to feature programming the level 1, level ...
Page 525
Univerge sv8100 issue 11.0 directory dialing 2 - 493 operation to use directory dialing from a multiline terminal with an lcd: 1. Press the dir softkey. -or- press the right cursor key. 2. Press the softkey for the directory dialing type: spd–speed dials ext–co-worker’s extensions sta–personal speed...
Page 526
Issue 11.0 univerge sv8100 2 - 494 directory dialing this page intentionally left blank.
Page 527
Univerge sv8100 issue 11.0 distinctive ringing, tones and flash patterns 2 - 495 distinctive ringing, tones and flash patterns description distinctive ringing, tones and flash patterns provide extension users with audible and visual call status signals. This lets users tell the type of calls by list...
Page 528
Issue 11.0 univerge sv8100 2 - 496 distinctive ringing, tones and flash patterns if program 15-08 : incoming virtual extension ring tone setup is set to incoming ring tone extension, then program 15-10 : incoming virtualextension ring tone order setup must have one of the priorities set to incoming ...
Page 529
Univerge sv8100 issue 11.0 distinctive ringing, tones and flash patterns 2 - 497 figure 2-12 trunk distinctive ringing flow chart.
Page 530
Issue 11.0 univerge sv8100 2 - 498 distinctive ringing, tones and flash patterns default setting enabled figure 2-13 icm distinctive ringing flow chart.
Page 531
Univerge sv8100 issue 11.0 distinctive ringing, tones and flash patterns 2 - 499 system availability terminals all multiline terminals required component(s) none related features call arrival (car) keys single line telephones, analog 500/2500 sets guide to feature programming the level 1, level 2 an...
Page 532
Issue 11.0 univerge sv8100 2 - 500 distinctive ringing, tones and flash patterns 15-02-03 multiline telephone basic data setup – extension ring tone select the extension intercom ring tone. 1 = high 2 = medium 3 = low 4 = ring tone 1 5 = ring tone 2 6 = ring tone 3 7 = ring tone 4 8 = ring tone 5 (d...
Page 533
Univerge sv8100 issue 11.0 distinctive ringing, tones and flash patterns 2 - 501 15-08-01 incoming virtual extension ring tone setup assign a ring tone range (0~8) to incoming virtual extensions assigned to a virtual extension key (program 15-07). Icm tone pattern, 0 = pattern 1 1 = pattern 2 2 = pa...
Page 534
Issue 11.0 univerge sv8100 2 - 502 distinctive ringing, tones and flash patterns 20-15-07 ring cycle setup – door box ringing for slt define the ringing cycle for door box ringing for single line telephone. Ringing cycle = 1~13 (default = 8) 20-15-08 ring cycle setup – virtual extension ring define ...
Page 535
Univerge sv8100 issue 11.0 distinctive ringing, tones and flash patterns 2 - 503 80-01-02 (39) service tone setup – basic tone number the following features require that the system tones listed below be changed to match the table. After changing these settings the chassis must be reset for the chang...
Page 536
Issue 11.0 univerge sv8100 2 - 504 distinctive ringing, tones and flash patterns operation to listen to the incoming ring choices: 1. Press speaker. 2. Dial 711. 3. Dial 1 to check ringing for intercom calls. - or - dial 2 to check ringing for trunk calls. 4. For intercom calls, select the pitch you...
Page 537
Univerge sv8100 issue 11.0 distinctive ringing, tones and flash patterns 2 - 505 to change the pitch of your incoming ring (multiline terminal only): 1. Press speaker. 2. Dial 720. 3. Dial 1 to change ringing for intercom calls. - or - dial 2 to change ringing for trunk calls. 4. Select the pitch (1...
Page 538
Issue 11.0 univerge sv8100 2 - 506 distinctive ringing, tones and flash patterns this page intentionally left blank.
Page 539: Do Not Disturb
Univerge sv8100 issue 11.0 do not disturb 2 - 507 do not disturb description do not disturb blocks incoming calls and paging announcements. Dnd permits an extension user to work by the telephone undisturbed by incoming calls and announcements. The user can activate dnd while their telephone is idle ...
Page 540
Issue 11.0 univerge sv8100 2 - 508 do not disturb call arrival (car) key/ virtual extension (ve) do not support dnd programmable function keys. Multiline terminal users can activate or deactivate do not disturb while on a call. This option is not available for single line telephones. When dnd and ca...
Page 541
Univerge sv8100 issue 11.0 do not disturb 2 - 509 system availability terminals all terminals required component(s) none related features call forwarding call forwarding/do not disturb override central office calls, answering direct inward line (dil) distinctive ringing, tones and flash patterns sel...
Page 542
Issue 11.0 univerge sv8100 2 - 510 do not disturb guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature prog...
Page 543
Univerge sv8100 issue 11.0 do not disturb 2 - 511 operation to activate or deactivate do not disturb while your extension is idle: multiline terminal using softkeys 1. Do not lift handset. 2. Press program softkey. 3. Press dnd softkey. 4. Press set softkey. 5. Choose from the following softkeys: ex...
Page 544
Issue 11.0 univerge sv8100 2 - 512 do not disturb 3. Dial the dnd option code. 0 = cancel dnd 1 = incoming trunk calls blocked 2 = paging, incoming intercom, call forwards and transferred trunk calls blocked 3 = all calls blocked 4 = call forwards blocked single line telephone 1. Lift the handset. 2...
Page 545: Door Box
Univerge sv8100 issue 11.0 door box 2 - 513 door box description the door box is a self-contained intercom unit typically used to monitor an entrance door. A visitor at the door can press the door box call button (like a door bell). The door box then sends chime tones to all extensions programmed to...
Page 546
Issue 11.0 univerge sv8100 2 - 514 door box off-hook signaling is available for door boxes. If an extension user is on the telephone, the large led flashes indicating the door box ringing, and the display shows a call from the door box. Each channel in the pgd(2)-u10 adp has a jumper which must be s...
Page 547
Univerge sv8100 issue 11.0 door box 2 - 515 paging, external single line telephones, analog 500/2500 sets wireless dect (sip) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonl...
Page 548
Issue 11.0 univerge sv8100 2 - 516 door box 15-07-01 programmable function keys assign a function key for external call forward by doorphone (code 54). Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 32-01-01 door box timers –...
Page 549
Univerge sv8100 issue 11.0 door box 2 - 517 operation to call a door box: multiline terminal 1. Press speaker. 2. Dial 702. 3. Dial door box number (1~8). Single line telephone 1. Lift the handset. 2. Dial 702. 3. Dial door box number (1~8). To activate the door box strike: multiline terminal 1. Whi...
Page 550
Issue 11.0 univerge sv8100 2 - 518 door box to answer a door box call while busy on another call: multiline terminal if you are busy on a call, the display shows the incoming door box call and the large led flashes. 1. Press hold toplace your active call on hold. 2. When you hear dial tone, dial the...
Page 551
Univerge sv8100 issue 11.0 door box 2 - 519 to cancel call forwarding off-premise for a door box: 1. At the multiline terminal, press speaker + dial sc 722. - or - at the multiline terminal only, press external forward by doorphone key (program 15-07-01 or sc 751, code 54). - or - at the single line...
Page 552
Issue 11.0 univerge sv8100 2 - 520 door box this page intentionally left blank.
Page 553: Drop Key
Univerge sv8100 issue 11.0 drop key 2 - 521 drop key description the drop key abandons a call while retaining the pbx/centrex line to originate another call. The drop key is provided by programming a function key. This feature allows recall to be used to provide a hookflash to the pbx or central off...
Page 554
Issue 11.0 univerge sv8100 2 - 522 drop key guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmin...
Page 555
Univerge sv8100 issue 11.0 drop key 2 - 523 20-06-01 class of service for extensions assign a class of service (1~15) to an extension. Day night/mode: 1~8 class of service of extensions (1~15) default: extension port 101 = class 15 all other extension port = class 1 81-10-07 coi initial data setup –...
Page 556
Issue 11.0 univerge sv8100 2 - 524 drop key operation to use the drop key from a multiline terminal with a co/pbx call in progress: 1. Press the function key programmed as a drop key. 2. Receive the new co/pbx dial tone. 3. Dial the desired number. To use feature plus recall from a multiline termina...
Page 557: Term
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 525 d term cordless ii terminal description the nec d term cordless ii terminal may be used with the univerge sv8100 kts. The dtr-4r-1 tel uses 900 mhz digital spread spectrum (dss) technology and must be connected in tandem to a multiline t...
Page 558
Issue 11.0 univerge sv8100 2 - 526 d term cordless ii terminal when a cordless terminal is ringing, press the flashing function key programmed for dss to answer the call. Synchronous ringing does not apply to the cordless terminals. A beep indicates when the cordless terminal receives off-hook ringi...
Page 559
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 527 system availability terminals dtr-4r-1 tel required component(s) cd-8dlca -or- cd-8dlca with pz-8dlcb daughter board -or- cd-16dlca related features none.
Page 560
Issue 11.0 univerge sv8100 2 - 528 d term cordless ii terminal guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for...
Page 561
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 529 10-03-06 etu setup (dlca pkg setup) – terminal type (b2) set up and confirm the basic configuration data for terminal type. 0 = not set 6 = pgd(2)-u10 adp (paging) 7 = pgd(2)-u10 adp (tone ringer) 8 = pgd(2)-u10 adp (door box) 9 = pgd(2)...
Page 562
Issue 11.0 univerge sv8100 2 - 530 d term cordless ii terminal 20-07-05 class of service options (administrator level) – set/ cancel automatic trunk-to-trunk transfer turn off or on an extension user ability to use the trunk-to-trunk forwarding service codes. 0 = off 1 = on (default = 0 for cos 1~15...
Page 563
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 531 20-07-20 class of service options (administrator level) – smdr printout accumulated account code data define the cos for the smdr printout of accumulated account code data. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for cos 1...
Page 564
Issue 11.0 univerge sv8100 2 - 532 d term cordless ii terminal 20-08-06 class of service options (outgoing call service) – toll restriction override turn off or on toll restricting override (service code 663). 0 = off 1 = on (default = 0 for cos 1~15) 20-08-07 class of service options (outgoing call...
Page 565
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 533 20-08-15 class of service options (outgoing call service) – block outgoing caller id turn off or on a user class of service from automatically blocking outgoing caller id information when a call is placed. If block is enabled, the system...
Page 566
Issue 11.0 univerge sv8100 2 - 534 d term cordless ii terminal 20-09-03 class of service options (incoming call service) – sub address identification define whether or not an extension displays the caller sub-address. 0 = off 1 = on (default = 0 for cos 1~15) 20-09-04 class of service options (incom...
Page 567
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 535 20-10-06 class of service options (answer service) – meet-me conference and paging turn off or on an extension user ability to use meet-me conference and paging. 0 = off 1 = on (default = 1 for cos 1~15) 20-10-07 class of service options...
Page 568
Issue 11.0 univerge sv8100 2 - 536 d term cordless ii terminal 20-11-07 class of service options (hold/ transfer service) – transfer without holding turn off or on an extension user ability to use transfer without holding. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-08 class of service options (...
Page 569
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 537 20-11-17 class of service options (hold/ transfer service) – department group trunk-to-trunk transfer (each telephone group transfer) turn off or on an extension user ability in a department group to use the trunk-to-trunk forwarding ser...
Page 570
Issue 11.0 univerge sv8100 2 - 538 d term cordless ii terminal 20-13-02 class of service options (supplementary service) – long conversation cutoff (incoming) turn off or on extension user ability to use long conversation cutoff for incoming calls. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-03 ...
Page 571
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 539 20-13-15 class of service options (supplementary service) – barge-in, initiate turn off or on an extension user ability to barge-in on other's calls. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-16 class of service options (supplement...
Page 572
Issue 11.0 univerge sv8100 2 - 540 d term cordless ii terminal 20-13-26 class of service options (supplementary service) – group listen turn off or on an extension user ability to use group listen. 0 = off 1 = on (default = 1 for cos 1~15) 20-13-27 class of service options (supplementary service) – ...
Page 573
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 541 20-13-38 class of service options (supplementary service) – headset ringing for slt turn off or on an extension user ability to use the headset ringing. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-39 class of service options (supplem...
Page 574
Issue 11.0 univerge sv8100 2 - 542 d term cordless ii terminal operation to program the d term cordless ii: 1. Press and hold down and # , then press talk. The f1 led flashes red. 2. Press r/vol repeatedly to scroll through the line key (lk) and feature options for function key f1. 3. Press mute to ...
Page 575
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 543 3. Announce the call after tone burst or wait for call to be answered. To place an outside call: 1. Press talk. X icon is displayed . 2. Dial trunk access code and number -or- select trunk appearance and dial number. Wait for call to be ...
Page 576
Issue 11.0 univerge sv8100 2 - 544 d term cordless ii terminal to place a conference call: 1. With a call in progress, press conf. 2. Place second internal or external call. 3. Announce conference. 4. Press conf again. A 3-party conference is established. When any party hangs up, the conference stil...
Page 577
Univerge sv8100 issue 11.0 d term cordless ii terminal 2 - 545 to switch from cordless to desk using base unit: 1. When cordless ii is associated with a terminal, use the base unit to switch between cordless ii and the multiline terminal. Refer to cordless ii base unit controls illustration on the n...
Page 578
Issue 11.0 univerge sv8100 2 - 546 d term cordless ii terminal 9. The handset displays digital (f8), and changes redial program to desk/cordless softkey switching mode. 10. Press talk to restore standby mode. 11. Press redial to test this feature. 12. The base unit automatically changes from desk to...
Page 579: Term
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 547 d term cordless lite ii terminal description the nec d term cordless ii lite terminal may be used with the univerge sv8100 system. The dth-4r-1 tel uses 900 mhz fm with adpcm (digital) technology and is connected in tandem to a mult...
Page 580
Issue 11.0 univerge sv8100 2 - 548 d term cordless lite ii terminal synchronous ringing does not apply to the cordless terminals. A beep indicates when the cordless terminal receives off-hook ringing. A spare battery is available as an optional available part. A second battery is not shipped with th...
Page 581
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 549 required component(s) cd-8dlca -or- cd-8dlca with pz-8dlcb daughter board -or- cd-16dlca related features cordless telephone connection guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that...
Page 582
Issue 11.0 univerge sv8100 2 - 550 d term cordless lite ii terminal 10-03-02 etu setup (dlca pkg setup) – logical port number (b1) set up and confirm the basic configuration data for logical port number (b1). 0 = not set 1 = multiline terminal (1~256) 2 = slt adapter (1~256) 6 = pgd(2)-u10 adp (pagi...
Page 583
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 551 10-03-07 etu setup (dlca pkg setup) – logical port number (b2) set up and confirm the basic configuration data for logical port number (b2). 0 = not set 6 = pgd(2)-u10 adp (ext. Speaker) 7 = pgd(2)-u10 adp (paging/tone ringer = 1~8)...
Page 584
Issue 11.0 univerge sv8100 2 - 552 d term cordless lite ii terminal 20-07-11 class of service options (administrator level) – forced trunk disconnect (analog trunk only) turn off or on an extension user ability to use forced trunk disconnect. This allows the extension to disconnect an unsupervised c...
Page 585
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 553 20-07-20 class of service options (administrator level) – smdr printout accumulated account code data define if accumulated account code data is included in the smdr printout for each class of service. 0 = off 1 = on (default = 0 fo...
Page 586
Issue 11.0 univerge sv8100 2 - 554 d term cordless lite ii terminal 20-08-06 class of service options (outgoing call service) – toll restriction override turn off or on toll restricting override (service code 663). 0 = off 1 = on (default = 0 for cos 1~15) 20-08-07 class of service options (outgoing...
Page 587
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 555 20-08-15 class of service options (outgoing call service) – block outgoing caller id turn off or on a user class of service from automatically blocking outgoing caller id information when a call is placed. If block is enabled, the s...
Page 588
Issue 11.0 univerge sv8100 2 - 556 d term cordless lite ii terminal 20-09-04 class of service options (incoming call service) – notification for incoming call list existence determine whether or not the check list message is displayed to indicate a missed call. 0 = off 1 = on (default = 0 for cos 1~...
Page 589
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 557 20-10-07 class of service options (answer service) – automatic off-hook answer turn off or on an extension user ability to use universal auto answer (no service code required). 0 = off 1 = on (default = 0 for cos 1~15) 20-10-08 clas...
Page 590
Issue 11.0 univerge sv8100 2 - 558 d term cordless lite ii terminal 20-11-08 class of service options (hold/ transfer service) – transfer information display turn off or on an extension incoming transfer pre-answer display. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-09 class of service options ...
Page 591
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 559 20-11-18 class of service options (hold/ transfer service) – no recall allow/deny answered transferred calls from recalling the originating extension. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-19 class of service options (hold...
Page 592
Issue 11.0 univerge sv8100 2 - 560 d term cordless lite ii terminal 20-13-03 class of service options (supplementary service) – long conversation cutoff (outgoing) turn off or on an extension user ability to use long conversation cutoff for outgoing calls. 0 = off 1 = on (default = 0 for cos 1~15) 2...
Page 593
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 561 20-13-16 class of service options (supplementary service) – barge-in, receive turn off or on barge-in at the receiving extension (i.E., barge-in receive). 0 = off 1 = on (default = 0 for cos 1~15) 20-13-17 class of service options (...
Page 594
Issue 11.0 univerge sv8100 2 - 562 d term cordless lite ii terminal 20-13-27 class of service options (supplementary service) – busy on seizing virtual extension if set to 1, a busy extension can be called, while someone is talking on a virtual extension key. Program 20-13-06 (call waiting) must be ...
Page 595
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 563 20-13-39 class of service options (supplementary service) – acd queue status display turn off or on the acd queue status display for an extension class of service. Any extension with this option enabled also hears the queue alarm. 0...
Page 596
Issue 11.0 univerge sv8100 2 - 564 d term cordless lite ii terminal operation to set up and program the d term cordless lite ii (dth-4r-1): 1. Press and hold down and # , then press talk. The f1 led flashes red and f1=lk01 is displayed on the lcd. 2. Press ring/vol repeatedly to scroll through the l...
Page 597
Univerge sv8100 issue 11.0 d term cordless lite ii terminal 2 - 565 a call in progress cannot be switched between the d term cordless lite ii and the associated multiline telephone. Switching held calls between the d term cordless lite ii telephone and the associated multiline telephone is not recom...
Page 598
Issue 11.0 univerge sv8100 2 - 566 d term cordless lite ii terminal this page intentionally left blank.
Page 599: Dtplusware
Univerge sv8100 issue 11.0 dtplusware 2 - 567 dtplusware description dtplusware is a server based xml application that allows nec ip display phones (dt710/730/750) access to the following features and options: view list of received, missed and outgoing calls. Send and receive instant messages to oth...
Page 600
Issue 11.0 univerge sv8100 2 - 568 dtplusware refer to table 2-20 dtplusware oai/tapi license feature matrix for a listing of supported functionality depending on whether the sv8100 is licensed for the minimum oai or includes the optional tapi license. Conditions after a dtplusware sets call forward...
Page 601
Univerge sv8100 issue 11.0 dtplusware 2 - 569 up to 12 predefined instant message templates are supported per dt750/sophisticated user. For contact database pop up to occur on incoming trunk calls caller id information must be provided. Dtplusware version 1.Xx does not provide a contact pop-up for c...
Page 602
Issue 11.0 univerge sv8100 2 - 570 dtplusware when using desktop suite and dtplusware in the same system, dtplusware mobile extension event monitoring is not supported. Windows xp iis server supports a maximum of 10 concurrent external access users. If more than 10 concurrent external access users a...
Page 603
Univerge sv8100 issue 11.0 dtplusware 2 - 571 operating system windows xp professional with sp2 (supports a maximum of 10 concurrent users). Windows 2003 server (supports over 10 concurrent users, use win 2003 server if more than 10 concurrent users are required). Iis 5.1 or higher sv8100 requiremen...
Page 604
Issue 11.0 univerge sv8100 2 - 572 dtplusware guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programm...
Page 605
Univerge sv8100 issue 11.0 dtplusware 2 - 573 20-02-09 system options for multiline telephones – disconnect supervision set to enable (1) for dtplusware. Enable/disable disconnect supervision for the system trunks. 0 = disable 1 = enable (default = 1) 20-02-12 system options for multiline telephones...
Page 606
Issue 11.0 univerge sv8100 2 - 574 dtplusware operation for operation instructions, refer to the user guide for the appropriate telephone. 20-13-24 class of service options (supplementary service) – privacy release by pressing line key set to on (1) for dtplusware. Turn off or on an extension user a...
Page 607: Ecology
Ecology 2 - 575 e ecology description environmental issues, such as global warming or ecology are one of the most important themes in today's world. The following energy saving features are implemented in this system: power cut off mode: based on day/night mode switching, the system can automaticall...
Page 608
Issue 11.0 univerge sv8100 2 - 576 ecology conditions power cut off mode version 7000 or higher main software is required for this feature. If the v7000 enhancement license (0036) expires while in power cut off mode, power does not automatically recover. If this is expected to occur, disable the eco...
Page 609
Univerge sv8100 issue 11.0 ecology 2 - 577 if the power cut off mode is manually set to on during a scheduled power off time, power cut remains in the on state until the next power cut off time, or until the power cut off mode is manually set to off. Power saving mode if the multiline terminal is id...
Page 610
Issue 11.0 univerge sv8100 2 - 578 ecology guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programming...
Page 611
Univerge sv8100 issue 11.0 ecology 2 - 579 12-03-01 weekly night service switching assign one of the 10 time patterns programmed in program 12-02-01 to each day of the week. Night mode service group numbers: 01~32 time schedule pattern number: 1~10 day of week: 01 = sunday (default = time pattern 2)...
Page 612
Issue 11.0 univerge sv8100 2 - 580 ecology operation power cut off mode to cut the power for power save group 2 during the night time (19:00-6:00): program 20-53-01: power save group 2 set 1 for night mode service group number program 20-53-01: power save group 3 set 1 for night mode service group n...
Page 613
Univerge sv8100 issue 11.0 ecology 2 - 581 tel 102: power save group 2 tel 103: power save group 3 tel 104: power save group 3 the power to tel 101 and tel 102 cuts at night. Settings using service codes program 15-27-01: tel 101: power save group 2 tel 102: power save group 2 table 2-21 program 12-...
Page 614
Issue 11.0 univerge sv8100 2 - 582 ecology power off for power save group 2 1. Press speaker and dial (service code 731). 2. Dial 02, group 2 3. Dial 1, power off 4. Enter the password (default: 0000) power supply to the system is cut when all terminals of power save group 2 are in an idle state. Pa...
Page 615
Univerge sv8100 issue 11.0 ecology 2 - 583 settings using function keys power off for power save group 2 1. Assign power save key (sc751 code # 06) with additional data 02. 2. Press the power save key. 3. Enter the password (set in program 90-02-02 user id3). 4. The key turns red. Power on for power...
Page 616
Issue 11.0 univerge sv8100 2 - 584 ecology 2. One minute later, led areas highlighted in red darken at tel200. Power failure saving mode set program 15-27-02 to 1 for extensions to have the power cut when the system losses power and runs on battery backup. Example program 15-27-02: tel 101: set to a...
Page 617: E911 Compatibility
Univerge sv8100 issue 11.0 e911 compatibility 2 - 585 e911 compatibility description e911 compatibility ensures that emergency calls always get through. If an emergency occurs, a user goes to any telephone, lifts the handset and dials 911. The system built-in e911 compatibility places the emergency ...
Page 618
Issue 11.0 univerge sv8100 2 - 586 e911 compatibility emergency routing when an extension user dials 911, the system can automatically find a trunk for the call. The system can choose a route to which the user normally does not have access. If all normal routes are busy, the system can even disconne...
Page 619
Univerge sv8100 issue 11.0 e911 compatibility 2 - 587 the 911 cut through feature does not work when dialing trunk access+911 (version 3000 and lower software). The 911 cut through feature works when dialing trunk access+911 (version 4000 and higher software). Calling party number (cpn) cpn sent whe...
Page 620
Issue 11.0 univerge sv8100 2 - 588 e911 compatibility cpn sent when making a normal trunk call from a virtual extension (ve). Table 2-23 cpn for ve standard calls prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 21-13-01 cpn: prg terminal ve off off not assigned not assigned not assigned none not assigned...
Page 621
Univerge sv8100 issue 11.0 e911 compatibility 2 - 589 cpn sent when making a 911 call from a terminal. Table 2-24 cpn for 911 calls prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 21-13-01 cpn: prg off off not assigned not assigned none assigned none assigned not assigned 21-12-01 assigned 21-12-01 o...
Page 622
Issue 11.0 univerge sv8100 2 - 590 e911 compatibility cpn sent when making a 911 call from a virtual extension (ve). Table 2-25 cpn for ve 911 calls prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 21-13-01 cpn: prg terminal ve off off not assigned not assigned not assigned none not assigned assigned none...
Page 623
Univerge sv8100 issue 11.0 e911 compatibility 2 - 591 cpn sent when making a normal trunk call across ccis trunks from a terminal. Figure 2-16 ccis standard calls table 2-26 cpn for ccis standard calls system a system b cpn: prg v3000 and lower cpn: prg v4000 and higher prg 99-01-58 prg 20-08-13 prg...
Page 624
Issue 11.0 univerge sv8100 2 - 592 e911 compatibility off on not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) o...
Page 625
Univerge sv8100 issue 11.0 e911 compatibility 2 - 593 on off not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) o...
Page 626
Issue 11.0 univerge sv8100 2 - 594 e911 compatibility on on not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on...
Page 627
Univerge sv8100 issue 11.0 e911 compatibility 2 - 595 cpn sent when making a normal trunk call across ccis trunks from a virtual extension (ve). Table 2-27 cpn for ccis ve standard calls system a system b cpn: prg v3000 and lower cpn: prg v4000 and higher prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 2...
Page 628
Issue 11.0 univerge sv8100 2 - 596 e911 compatibility off off assigned not assigned not assigned off not assigned off none 21-12-01 (sysa) on 21-12-01 (sysa) 21-12-01 (sysa) assigned off 21-12-01 (sysb) 21-12-01 (sysa) on 21-12-01 (sysa) 21-12-01 (sysa) on not assigned off none 21-12-01 (sysa) on 21...
Page 629
Univerge sv8100 issue 11.0 e911 compatibility 2 - 597 off on not assigned not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-1...
Page 630
Issue 11.0 univerge sv8100 2 - 598 e911 compatibility off on assigned not assigned not assigned off not assigned off none 21-12-01 (sysa) on 21-12-01 (sysa) 21-12-01 (sysa) assigned off 21-12-01 (sysb) 21-12-01 (sysa) on 21-12-01 (sysa) 21-12-01 (sysa) on not assigned off none 21-12-01 (sysa) on 21-...
Page 631
Univerge sv8100 issue 11.0 e911 compatibility 2 - 599 on off not assigned not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-1...
Page 632
Issue 11.0 univerge sv8100 2 - 600 e911 compatibility on off assigned not assigned not assigned off not assigned off none 21-12-01 (sysa) on 21-12-01(sysa) 21-12-01 (sysa) assigned off 21-12-01 (sysb) 21-12-01 (sysa) on 21-12-01(sysa) 21-12-01 (sysa) on not assigned off none 21-12-01 (sysa) on 21-12...
Page 633
Univerge sv8100 issue 11.0 e911 compatibility 2 - 601 on on not assigned not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12...
Page 634
Issue 11.0 univerge sv8100 2 - 602 e911 compatibility on on assigned not assigned not assigned off not assigned off none 21-12-01 (sysa) on 21-12-01(sysa) 21-12-01 (sysa) assigned off 21-12-01 (sysb) 21-12-01 (sysa) on 21-12-01(sysa) 21-12-01 (sysa) on not assigned off none 21-12-01 (sysa) on 21-12-...
Page 635
Univerge sv8100 issue 11.0 e911 compatibility 2 - 603 cpn sent when making a 911 call across ccis trunks from a terminal. Table 2-28 cpn for ccis 911 calls system a system b cpn: prg v3000 and lower cpn: prg v4000 and higher prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 21-13-01 prg 20-08-13 prg 21-12-...
Page 636
Issue 11.0 univerge sv8100 2 - 604 e911 compatibility off on not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) o...
Page 637
Univerge sv8100 issue 11.0 e911 compatibility 2 - 605 on off not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) o...
Page 638
Issue 11.0 univerge sv8100 2 - 606 e911 compatibility on on not assigned not assigned off not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on 21-12-01 (sysb) 21-12-01 (sysb) on not assigned off none none on none none assigned off 21-12-01 (sysb) 21-12-01 (sysb) on...
Page 639
Univerge sv8100 issue 11.0 e911 compatibility 2 - 607 cpn sent when making a 911 call across ccis trunks from a virtual extension (ve). Table 2-29 cpn for ccis ve 911 calls system a system b cpn: prg v3000 and lower cpn: prg v4000 and higher prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 21-13-01 prg 20...
Page 640
Issue 11.0 univerge sv8100 2 - 608 e911 compatibility off off assigned not assigned not assigned off not assigned off none 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) assigned off 21-12-01(sysb) 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) on not assigned off none 21-12-01(sysa) on 21-12-01(s...
Page 641
Univerge sv8100 issue 11.0 e911 compatibility 2 - 609 off on not assigned not assigned not assigned off not assigned off none none on none none assigned off 21-12-01(sysb) 21-12-01(sysb) on 21-12-01(sysb) 21-12-01(sysb) on not assigned off none none on none none assigned off 21-12-01(sysb) 21-12-01(...
Page 642
Issue 11.0 univerge sv8100 2 - 610 e911 compatibility off on assigned not assigned not assigned off not assigned off none 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) assigned off 21-12-01(sysb) 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) on not assigned off none 21-12-01(sysa) on 21-12-01(sy...
Page 643
Univerge sv8100 issue 11.0 e911 compatibility 2 - 611 on off not assigned not assigned not assigned off not assigned off none none on none none assigned off 21-12-01(sysb) 21-12-01(sysb) on 21-12-01(sysb) 21-12-01(sysb) assigned on not assigned off none none on none none assigned off 21-12-01(sysb) ...
Page 644
Issue 11.0 univerge sv8100 2 - 612 e911 compatibility on off assigned not assigned not assigned off not assigned off none 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) assigned off 21-12-01(sysb) 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) on not assigned off none 21-12-01(sysa) on 21-12-01(sy...
Page 645
Univerge sv8100 issue 11.0 e911 compatibility 2 - 613 on on not assigned not assigned not assigned off not assigned off none none on none none assigned off 21-12-01(sysb) 21-12-01(sysb) on 21-12-01(sysb) 21-12-01(sysb) on not assigned off none none on none none assigned off 21-12-01(sysb) 21-12-01(s...
Page 646
Issue 11.0 univerge sv8100 2 - 614 e911 compatibility on on assigned not assigned not assigned off not assigned off none 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) assigned off 21-12-01(sysb) 21-12-01(sysa) on 21-12-01(sysa) 21-12-01(sysa) on not assigned off none 21-12-01(sysa) on 21-12-01(sys...
Page 647
Univerge sv8100 issue 11.0 e911 compatibility 2 - 615 cpn sent when making a 911 call from a terminal by pressing a co line key and then dialing 911. Default setting disabled system availability terminals none table 2-30 cpn for line key+911 calls prg 99-01-58 prg 20-08-13 prg 21-12-01 prg 21-13-01 ...
Page 648
Issue 11.0 univerge sv8100 2 - 616 e911 compatibility required component(s) none related features automatic route selection central office calls, placing t1 trunking (with ani/dnis compatibility) isdn compatibility guide to feature programming the level 1, level 2 and level 3 columns indicate the pr...
Page 649
Univerge sv8100 issue 11.0 e911 compatibility 2 - 617 14-06-01 trunk group routing – priority order number set the priority order number 1~4. 0 = not specify 1~100 : (trunk group number) 1001~1100 : (1000 + route table number) default: route 1, order number 1 = 1 (trunk group 1) order numbers 2, 3, ...
Page 650
Issue 11.0 univerge sv8100 2 - 618 e911 compatibility calling party number presentation: program number program name description/comments assigned data level 1 2 3 10-03-05 etu setup (prta pkg setup) – clip information based on this setting, the system includes a presentation allowed (1) or presenta...
Page 651
Univerge sv8100 issue 11.0 e911 compatibility 2 - 619 operation to place an emergency 911 call: when dial 911 routing without trunk access is enabled 1. Go to any telephone. 2. Lift the handset or press speaker. 3. Dial 911. When dial 911 routing without trunk access is disabled 1. Go to any telepho...
Page 652
Issue 11.0 univerge sv8100 2 - 620 e911 compatibility to turn off the e911 alarm at your telephone: 1. Lift the handset or press speaker. 2. Dial 786. The alarm goes off. - or - (if you have a display telephone) 1. Press the exit key once to turn off the alarm. 2. Press the exit key again to clear t...
Page 653: Electra Elite Ipk Terminals
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 621 electra elite ipk terminals description the electra elite ipk terminals provide ergonomic form and user-friendly functions. With advanced digital circuitry, the ipk terminals consist of distinct models to meet diverse user telephone term...
Page 654
Issue 11.0 univerge sv8100 2 - 622 electra elite ipk terminals the lcd of the univerge sv8100 terminal provides a volume bar indication, while adjusting the following volume levels or controls: speaker volume handset/headset volume bgm volume ring volume/off-hook ring volume lcd contrast only englis...
Page 655
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 623 with non-ip electra elite ipk terminals, up to two adapters can be installed in a telephone. For compatibility of multiple adapter units, refer to the following table: an ac-2r unit/ac-3r unit (ac adapter) is required when any of the fol...
Page 656
Issue 11.0 univerge sv8100 2 - 624 electra elite ipk terminals required component(s) cd-8dlca blade pz-8dlcb daughter board cd-16dlca blade optional component(s) ad(a)-r unit (adapter for call recording) ap(a)-r unit (analog port adapter [without ringer]) ap(r)-r unit (analog port adapter [with ring...
Page 657
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 625 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for...
Page 658
Issue 11.0 univerge sv8100 2 - 626 electra elite ipk terminals 10-03-04 etu setup (dlca pkg setup) – optional installed unit 1 (only applies to dth/dtr telephones) set up and confirm the basic configuration data for optional installed unit 1. 0 = none 1 = apr module 2 = apa module 3 = ada module 4 =...
Page 659
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 627 20-07-01 class of service options (administrator level) – manual night service enabled turn off or on an extension for manual night service switching (service code 718). This option must be enabled for an extension to display the night i...
Page 660
Issue 11.0 univerge sv8100 2 - 628 electra elite ipk terminals 20-07-13 class of service options (administrator level) – vrs record (vrs msg operation) turn off or on an extension user ability to record, erase or listen to vrs messages. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for cos ...
Page 661
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 629 20-07-25 class of service options (administrator level) – set/ cancel caller id refuse enable/disable an extension user ability to set or cancel caller id refuse. 0 = off 1 = on (default = 0 for cos 1~15) 20-07-26 class of service option...
Page 662
Issue 11.0 univerge sv8100 2 - 630 electra elite ipk terminals 20-08-09 class of service options (outgoing call service) – hotline/extension ringdown turn off or on ringdown extension for extensions with this cos. 0 = off 1 = on (default = 0 for cos 1~15) 20-08-10 class of service options (outgoing ...
Page 663
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 631 20-08-19 class of service options (outgoing call service) – hotline for spk turn off or on an extension user ability to activate hotline or ringdown when pressing speaker. 0 = off 1 = on (default = 0 for cos 1~15) 20-08-20 class of servi...
Page 664
Issue 11.0 univerge sv8100 2 - 632 electra elite ipk terminals 20-09-05 class of service options (incoming call service) – signal/ voice call turn off or on an extension user ability to enable handsfree answerback or forced intercom ringing for their incoming intercom calls. 0 = off 1 = on (default ...
Page 665
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 633 20-10-08 class of service options (answer service) – virtual extension off-hook answer turn off or on an extension user ability to answer an incoming call on a call arrival (car)/secondary incoming extension (sie)/ virtual extension simp...
Page 666
Issue 11.0 univerge sv8100 2 - 634 electra elite ipk terminals 20-11-08 class of service options (hold/ transfer service) – transfer information display turn off or on an extension incoming transfer preanswer display. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-09 class of service options (hold/...
Page 667
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 635 20-11-18 class of service options (hold/ transfer service) – no recall no recall set to allow does not stop transferred calls from recalling from a virtual extension. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-19 class of service op...
Page 668
Issue 11.0 univerge sv8100 2 - 636 electra elite ipk terminals 20-13-01 class of service options (supplementary service) – long conversation alarm turn off or on the warning tone for long conversation (not for single line telephones). 0 = off 1 = on (default = 0 for cos 1~15) 20-13-02 class of servi...
Page 669
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 637 20-13-12 class of service options (supplementary service) – room monitor, extension being monitored turn off or on an extension ability to be monitored by other extensions. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-13 class of serv...
Page 670
Issue 11.0 univerge sv8100 2 - 638 electra elite ipk terminals 20-13-22 class of service options (supplementary service) – busy status display (called party status) turn off or on an extension ability to display the detail state of called party. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-23 cla...
Page 671
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 639 20-13-33 class of service options (supplementary service) – acd supervisor’s position enhancement set this option to on for the operator to use service codes in program 11-13-10 through program 11-13-13. 0 = off 1 = on (default = 0 for c...
Page 672
Issue 11.0 univerge sv8100 2 - 640 electra elite ipk terminals 20-13-45 class of service options (supplementary service) – mic key mode while call monitoring set per class of service, when in call monitoring mode determines if the monitored party receives the barge in alert tone when coaching mode i...
Page 673
Univerge sv8100 issue 11.0 electra elite ipk terminals 2 - 641 20-14-05 class of service options for disa/e&m – operator calling enable/disable a disa or tie trunk caller ability to dial 0 for the telephone system operator. 0 = off 1 = on (default = 1 for cos 1~15) 20-14-06 class of service options ...
Page 674
Issue 11.0 univerge sv8100 2 - 642 electra elite ipk terminals operation refer to individual features for details. Table 2-31 electra elite ipk telephone specifications dth-16ld-1 dth-32d-1 dth-16d-1 dth-8d-1 dth-8-1 dedicated function keys 11 11 11 11 11 line/feature access/ programmable feature ac...
Page 675
Facsimile co branch connection 2 - 643 f facsimile co branch connection description the univerge sv8100 system provides branch connection of locally provided facsimile machines to co/pbx lines. Additional dedicated co/pbx lines are not required for a facsimile to operate. The facsimile shares any co...
Page 676
Issue 11.0 univerge sv8100 2 - 644 facsimile co branch connection system availability terminals none required component(s) cd-4cotb related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the...
Page 677
Univerge sv8100 issue 11.0 facsimile co branch connection 2 - 645 operation none 14-05-01 trunk group assign trunks to trunk groups (1~100). Trunk group number: 0~100 priority number: 1~200 (default trunks 1~200 = priority 1~200) 22-01-04 system options for incoming calls – dil no answer recall time...
Page 678
Issue 11.0 univerge sv8100 2 - 646 facsimile co branch connection this page intentionally left blank.
Page 679: Flash
Univerge sv8100 issue 11.0 flash 2 - 647 flash description flash allows an extension user to access certain co and pbx features by interrupting the trunk loop current. Flash lets an extension user take full advantage of whatever features the connected telco or pbx offers. You must set the flash para...
Page 680
Issue 11.0 univerge sv8100 2 - 648 flash related features drop key pbx compatibility vm8000 inmail guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are us...
Page 681
Univerge sv8100 issue 11.0 flash 2 - 649 15-03-04 single line telephone basic data setup – flashing enable/disable flash for single line (500/2500 type) telephones. 0 = no 1 = yes (default = 1) 81-10-07 cot initial data setup – hookflash time selection 1 set the flash duration (16~4080ms) for analog...
Page 682
Issue 11.0 univerge sv8100 2 - 650 flash operation to flash the trunk you are on: from a multiline terminal 1. Press recall. From a single line telephone 1. Hookflash. 2. Dial # 3..
Page 683: Flexible System Numbering
Univerge sv8100 issue 11.0 flexible system numbering 2 - 651 flexible system numbering description flexible system numbering lets you reassign the system port-to-extension assignments. This allows an employee to retain their extension number if they move to a different office. In addition, factory t...
Page 684
Issue 11.0 univerge sv8100 2 - 652 flexible system numbering conditions programming follows a telephone extension number, not the port number in most cases. If you relocate a telephone, you may need to change additional programming. For example, if you change the extension assigned to a port in prog...
Page 685
Univerge sv8100 issue 11.0 flexible system numbering 2 - 653 default setting extensions and virtuals are numbered in the following order: program 11-02-01 and program 11-04-01 physical extensions: extn port 1 = 101 ~ extn port 99 = 199 extn port 100 = 3101 ~ extn port 256 = 3257 virtual extensions/c...
Page 686
Issue 11.0 univerge sv8100 2 - 654 flexible system numbering system availability terminals all terminals required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the...
Page 687
Univerge sv8100 issue 11.0 flexible system numbering 2 - 655 11-04-01 virtual extension numbering assign virtual extension numbers. Up to eight digits 1 201 2 202 3 203 ~ ~ 99 299 100 3601 ~ ~ 256 3857 11-06-01 aci extension numbering define the virtual extension number to be used for the aci extens...
Page 688
Issue 11.0 univerge sv8100 2 - 656 flexible system numbering 11-10-07 service code setup (for system administrator) – canceling the automatic transfer for each trunk line set the service code for canceling automatic transfer for each trunk line. Mlt (default = 734) 11-10-08 service code setup (for s...
Page 689
Univerge sv8100 issue 11.0 flexible system numbering 2 - 657 11-10-26 service code setup (for system administrator) – forced trunk disconnect customize the forced trunk disconnect service codes for the system administrator. Mlt, slt (default not assigned) 11-10-27 service code setup (for system admi...
Page 690
Issue 11.0 univerge sv8100 2 - 658 flexible system numbering 11-11-08 service code setup (for setup/ entry operation) – do not disturb set the service code for setting call forwarding for do not disturb. Mlt, slt (default = 747) 11-11-09 service code setup (for setup/ entry operation) – answer messa...
Page 691
Univerge sv8100 issue 11.0 flexible system numbering 2 - 659 11-11-21 service code setup (for setup/ entry operation) – check incoming ring tones check incoming ring tones used for registration and setup. Mlt (default = 711) 11-11-22 service code setup (for setup/ entry operation) – extension name p...
Page 692
Issue 11.0 univerge sv8100 2 - 660 flexible system numbering 11-11-34 service code setup (for setup/ entry operation) – temporary toll restriction override customize the temporary toll restriction override used for registration and setup. Mlt, slt (default = 775) 11-11-35 service code setup (for set...
Page 693
Univerge sv8100 issue 11.0 flexible system numbering 2 - 661 11-11-49 service code setup (for setup/ entry operation) – set/cancel call forward both ring (split) assign the call forward both ring split service code. Mlt, slt (default not assigned) 11-11-50 service code setup (for setup/ entry operat...
Page 694
Issue 11.0 univerge sv8100 2 - 662 flexible system numbering 11-12-05 service code setup (for service access) – cancel camp-on customize the service code, used for cancelling camp-on. Mlt, slt (default = 770) 11-12-06 service code setup (for service access) – switching of voice call and signal call ...
Page 695
Univerge sv8100 issue 11.0 flexible system numbering 2 - 663 11-12-21 service code setup (for service access) – meet-me answer to specified internal paging group customize the service codes used for meet-me answer to specified internal paging group service access. Mlt, slt (default = 764) 11-12-22 s...
Page 696
Issue 11.0 univerge sv8100 2 - 664 flexible system numbering 11-12-34 service code setup (for service access) – answer for group hold if required, redefine the service code used to answer a specific trunk which is either ringing or on hold. Mlt, slt (default = 762) 11-12-35 service code setup (for s...
Page 697
Univerge sv8100 issue 11.0 flexible system numbering 2 - 665 11-12-51 service code setup (for service access) – vm access (sv8100 inmail and vms) customize the service codes used for the vm access (inmail and vms). Mlt, slt (default = 8) 11-12-52 service code setup (for service access) – live monit...
Page 698
Issue 11.0 univerge sv8100 2 - 666 flexible system numbering 11-13-09 service code setup (for acd) – agent id code logout assign to allow an aic agent to log out of a group. Mlt (default not assigned) 11-13-10 service code setup (for acd) – acd agent login by supervisor assign to allow an acd superv...
Page 699
Univerge sv8100 issue 11.0 flexible system numbering 2 - 667 11-14-09 service code setup (for hotel) – set room to room call restriction customize the set room to room call extension used with the hotel/ motel feature. Mlt, slt (default = 635) 11-14-10 service code setup (for hotel) – cancel room to...
Page 700
Issue 11.0 univerge sv8100 2 - 668 flexible system numbering 11-15-03 service code setup, administrative (for special access) – backup data save this service code is used to back up the programmed data on the sram and call history to the flash rom. While saving the database, it may cause system lock...
Page 701
Univerge sv8100 issue 11.0 flexible system numbering 2 - 669 11-16-02 single digit service code setup – barge-in set up item 02 for single digit barge-in. For example, you can assign item 02 to use digit 5 for barge-in. This would allow you to program a function key with an extension number plus the...
Page 702
Issue 11.0 univerge sv8100 2 - 670 flexible system numbering operation none 11-20-02 dial extension analyze table – type of dials assign the type of dial for the extension analyze table from program 11-20-01. Type of dials: 0 = not used 1 = service code 2 = extension number 5 = operator access 6 = f...
Page 703: Flexible Timeouts
Univerge sv8100 issue 11.0 flexible timeouts 2 - 671 flexible timeouts description the flexible timeouts feature provides a variety of timers in the resident system program to allow the system to operate without initial programming. The system timers can be changed to meet customer needs according t...
Page 704
Issue 11.0 univerge sv8100 2 - 672 flexible timeouts 22-01-04 20-31-08 dil no answer recall time a dil that rings its programmed destination longer than this time diverts to the dil no answer ring group (program 22-08-01). Trunk timer class is referred by the trunk. 22-01-06 20-31-09 did ring-no-ans...
Page 705
Univerge sv8100 issue 11.0 flexible timeouts 2 - 673 conditions timer classes are also used for car/ve. When timer class is set to 0 it uses the system-wide timers. All stations and trunks are assigned to timer class 0 at default. Both system-wide timers (timer class 0) and timer class timers (timer...
Page 706
Issue 11.0 univerge sv8100 2 - 674 flexible timeouts required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are...
Page 707
Univerge sv8100 issue 11.0 flexible timeouts 2 - 675 20-31-02 timer class timer assignment – callback / trunk queuing cancel time the system cancels an extension callback or trunk queueing request after this time. 0~64800 (seconds) (default = 64800) 20-31-03 timer class timer assignment – car/sie/vi...
Page 708
Issue 11.0 univerge sv8100 2 - 676 flexible timeouts 20-31-11 timer class timer assignment – hold recall callback time (non exclusive hold) a trunk recalling from hold or park rings an extension for this time. This time works with hold recall time or park hold time. After this time, the system invok...
Page 709
Univerge sv8100 issue 11.0 flexible timeouts 2 - 677 20-31-20 timer class timer assignment – long conversation disconnect (trunk to trunk) determine the time the system waits before disconnecting a disa caller or any trunk-to-trunk (such as tandem trunking) conversation call after the long conversat...
Page 710
Issue 11.0 univerge sv8100 2 - 678 flexible timeouts 22-01-06 system options for incoming calls – did ring-no-answer time set the did ring no answer (rna) intercept time (0~64800 seconds). In systems with rna intercept, the did call rings the destination extension for this time, and then rings inter...
Page 711
Univerge sv8100 issue 11.0 flexible timeouts 2 - 679 operation please refer to the feature for the operation. 25-07-02 system timers for vrs/disa – vrs/disa no answer time a vrs/disa caller can ring an extension for this time before the system sets the call as a ring no answer. After this time expir...
Page 712
Issue 11.0 univerge sv8100 2 - 680 flexible timeouts this page intentionally left blank.
Page 713: Forced Trunk Disconnect
Univerge sv8100 issue 11.0 forced trunk disconnect 2 - 681 forced trunk disconnect description forced trunk disconnect allows an extension user to disconnect (release) another extension active outside call. The user can then place a call on the released trunk. Forced trunk disconnect lets a user acc...
Page 714
Issue 11.0 univerge sv8100 2 - 682 forced trunk disconnect related features central office calls, placing guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels...
Page 715
Univerge sv8100 issue 11.0 forced trunk disconnect 2 - 683 operation to disconnect a busy trunk: multiline terminal 1. Press line key for trunk. - or - dial trunk access code ( # 9 + trunk number). You hear busy tone. Trunk numbers are 001~200. 2. Dial the service code (not set at default). You hear...
Page 716
Issue 11.0 univerge sv8100 2 - 684 forced trunk disconnect this page intentionally left blank.
Page 717: General Purpose Relay
General purpose relay 2 - 685 g general purpose relay description the system allows up to eight general purpose relays using pgd(2)-u10 adp’s (four relays per pgd unit) and one general purpose relay built into the cd-cp00-us for a maximum of nine relays. These relays are normally opened and can be c...
Page 718
Issue 11.0 univerge sv8100 2 - 686 general purpose relay the general purpose relay cannot be activated by disa. Default setting disabled system availability terminals all multiline terminals (using access code) multiline terminal (using line key) required component(s) pgd(2)-u10 adp cd-cp00-us relat...
Page 719
Univerge sv8100 issue 11.0 general purpose relay 2 - 687 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featu...
Page 720
Issue 11.0 univerge sv8100 2 - 688 general purpose relay 10-05-01 general purpose relay setup – slot no. Physical port of dlca sensor circuit no. Define which relay circuits (5~8) on the pgd(2)-u10 adp are used for general purpose relays. A maximum of (8) general purpose relay can be assigned using ...
Page 721
Univerge sv8100 issue 11.0 general purpose relay 2 - 689 operation to activate a relay: multiline terminal 1. Press speaker. 2. Dial 780. 3. Dial relay number (0~8). 0 is for the relay on the cd-cp00-us, 1~8 are relays on the pgd(2)-u10 adp. - or - 1. Press the line key assigned as a general purpose...
Page 722
Issue 11.0 univerge sv8100 2 - 690 general purpose relay 3. Dial relay number (0~8). 0 is for the relay on the cd-cp00-us, 1~8 are relays on the pgd(2)-u10 adp. - or - 1. Press the line key assigned as a general purpose relay (the key is not lit). - or - 1. Wait for the drive timer to expire. Single...
Page 723: Group Call Pickup
Univerge sv8100 issue 11.0 group call pickup 2 - 691 group call pickup description group call pickup allows an extension user to answer a call ringing another extension in a pickup group. This permits co-workers in the same work area to easily answer each other’s calls. The user can dial a code or p...
Page 724
Issue 11.0 univerge sv8100 2 - 692 group call pickup system availability terminals all terminals required component(s) none related features central office calls, answering directed call pickup programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate ...
Page 725
Univerge sv8100 issue 11.0 group call pickup 2 - 693 11-12-27 service code setup (for service access) – call pickup customize the service codes for call pickup. Mlt, slt (default = # ) 11-12-28 service code setup (for service access) – call pickup for another group customize the service codes for ...
Page 726
Issue 11.0 univerge sv8100 2 - 694 group call pickup operation to answer a call ringing another telephone in your pickup group: 1. Pick up the handset or press speaker. 2. At multiline terminal only, press the group call pickup key (program 15-07 or sc 751: 24). - or - dial 756 or # . Service code #...
Page 727: Group Listen
Univerge sv8100 issue 11.0 group listen 2 - 695 group listen description group listen permits a multiline terminal user to talk on the handset and have their caller’s voice broadcast over the telephone speaker. This lets the multiline terminal user’s co-workers listen to the conversation. Group list...
Page 728
Issue 11.0 univerge sv8100 2 - 696 group listen guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progra...
Page 729
Univerge sv8100 issue 11.0 group listen 2 - 697 to cancel group listen (without hanging up your call): 1. Do not hang up. 2. Press the flashing speaker. You can talk to the caller over the handset. Your co-workers can no longer hear the caller’s voice..
Page 730
Issue 11.0 univerge sv8100 2 - 698 group listen this page intentionally left blank.
Page 731: Handset Mute
Handset mute 2 - 699 h handset mute description handset mute is provided to most terminals connected to the univerge sv8100 system. While talking on the multiline terminal handset, a station user can dial a feature code or press mic to mute the transmit speech path. The station user can still hear t...
Page 732
Issue 11.0 univerge sv8100 2 - 700 handset mute guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progra...
Page 733
Univerge sv8100 issue 11.0 handset mute 2 - 701 table 2-33 service tone setup defaults, program 80-01-01 service tone no. Service tone repeat count unit count basic tone no. Duration gain level (db) 1 no tone 0 basic 1 0 10 32 (0db) 2 internal dial tone 0 basic 1 9 10 32 (0db) 3 stutter dial tone 0 ...
Page 734
Issue 11.0 univerge sv8100 2 - 702 handset mute 19 door box chime 1 3 basic 6 4 4 2 2 2 0 2 2 3 4 6 5 38 (+3db) 26 (-3db) 38 (+3db) 26 (-3db) 14 (-9db) 32 (0db) 20 door box chime 2 3 basic 6 7 7 5 5 5 0 2 2 3 4 6 5 38 (+3db) 26 (-3db) 38 (+3db) 26 (-3db) 14 (-9db) 32 (0db) 21 door box chime 3 3 basi...
Page 735
Univerge sv8100 issue 11.0 handset mute 2 - 703 30 door box call tone 1 basic 2 0 6 1 1 32 (0db) 32 (0db) 31 paging tone 2 basic 2 0 6 1 1 32 (0db) 32 (0db) 32 splash tone 1 1 basic 2 0 6 1 1 32 (0db) 32 (0db) 33 splash tone 2 2 basic 2 0 6 1 1 32 (0db) 32 (0db) 34 splash tone 3 3 basic 2 0 6 1 1 32...
Page 736
Issue 11.0 univerge sv8100 2 - 704 handset mute 50 external special audible ring tone 0 3 10 12 0 10 2 30 32 (0db) 32 (0db) 32 (0db) 51 external intercept tone 0 2 12 4 3 2 32 (0db) 32 (0db) 52 external call waiting tone 1 1 12 3 32 (0db) 53 external executive override tone 1 1 12 10 32 (0db) 54 ---...
Page 737
Univerge sv8100 issue 11.0 handset mute 2 - 705 operation while talking on a terminal handset: 1. Press mic. - or - 2. Press feature + dial 1. - or - 3. Press the handset transmission cut-off key (program15-07-01; key 40 or sc 751 key code 40). Table 2-34 service tone setup, program 80-01-02 item no...
Page 738
Issue 11.0 univerge sv8100 2 - 706 handset mute this page intentionally left blank.
Page 739: Handsfree and Monitor
Univerge sv8100 issue 11.0 handsfree and monitor 2 - 707 handsfree and monitor description handsfree allows a multiline terminal user to process calls using the speaker and microphone in the telephone instead of the handset. Handsfree is a convenience for workers who do not have a free hand to pick ...
Page 740
Issue 11.0 univerge sv8100 2 - 708 handsfree and monitor system availability terminals all multiline terminals required component(s) none related features central office calls, answering central office calls, placing microphone cutoff prime line selection guide to feature programming the level 1, le...
Page 741
Univerge sv8100 issue 11.0 handsfree and monitor 2 - 709 operation to talk handsfree: 1. Press speaker, trunk line key or virtual extension key. 2. Place the call. 3. Speak toward the telephone when the called party answers. To change a handset call to a handsfree call: 1. Press speaker and hang up ...
Page 742
Issue 11.0 univerge sv8100 2 - 710 handsfree and monitor to turn on/off monitor: 1. Press mic, feature + 1, or the microphone function key (program 15-07 or sc 751 : 02) to turn on or off the microphone. Monitor is off when mic led is lit, the microphone function key is lit, or the handset is lifted...
Page 743
Univerge sv8100 issue 11.0 handsfree answerback/forced intercom ringing 2 - 711 handsfree answerback/forced intercom ringing description handsfree answerback permits an extension user to respond to a voice-announced intercom call by speaking toward the telephone, without lifting the handset. Like ha...
Page 744
Issue 11.0 univerge sv8100 2 - 712 handsfree answerback/forced intercom ringing related features handsfree and monitor microphone cutoff guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are m...
Page 745
Univerge sv8100 issue 11.0 handsfree answerback/forced intercom ringing 2 - 713 operation to enable handsfree answerback for your incoming intercom calls: 1. Press idle speaker. 2. Dial 721. 3. Press speaker to hang up. This disables forced intercom ringing. To enable forced intercom ringing for you...
Page 746
Issue 11.0 univerge sv8100 2 - 714 handsfree answerback/forced intercom ringing to change the way your intercom call signals the extension you are calling: 1. Dial 1. If ringing, your call voice-announces. If voice-announced, your call starts to ring the destination. This option is also available at...
Page 747: Headset Operation
Univerge sv8100 issue 11.0 headset operation 2 - 715 headset operation description a multiline terminal user can use a customer-provided headset in place of the handset. Like using handsfree, using the headset frees up the user’s hands for other work. However, headset operation provides privacy not ...
Page 748
Issue 11.0 univerge sv8100 2 - 716 headset operation required component(s) headset related features handsfree answerback/forced intercom ringing programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming t...
Page 749
Univerge sv8100 issue 11.0 headset operation 2 - 717 15-02-43 multiline telephone basic data setup – headset ring duration if incoming ringing is set for headset, set the duration the call rings the headset before ringing the speaker. 0 = no switch to speaker ring 1 = 10 seconds 2 = 20 seconds 3 = 3...
Page 750
Issue 11.0 univerge sv8100 2 - 718 headset operation operation to enable the headset: 1. Plug in the headset in the headset jack on the bottom of the telephone. 2. Program a headset key (program 15-07 or sc 751: 05). You hear a confirmation beep. To use the headset: the headset key lights when on a ...
Page 751: Hold
Univerge sv8100 issue 11.0 hold 2 - 719 hold description hold lets an extension user put a call in a temporary waiting state. The caller on hold hears silence or music on hold, not conversation in the extension user’s work area. While the call waits on hold, the extension user may process calls or u...
Page 752
Issue 11.0 univerge sv8100 2 - 720 hold conditions the called extension must lift the handset or press speaker before the call can be placed on hold. Callers on hold hear music on hold, if programmed. An extension can have function keys for system hold and exclusive hold. Analog single line telephon...
Page 753
Univerge sv8100 issue 11.0 hold 2 - 721 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programming. L...
Page 754
Issue 11.0 univerge sv8100 2 - 722 hold 14-07-01 trunk access map setup set up the trunk access maps. This sets the access options for trunks. 0 = no access 1 = outgoing access only 2 = incoming access only 3 = access only when trunk on hold 4 = outgoing access and access when trunk on hold 5 = inco...
Page 755
Univerge sv8100 issue 11.0 hold 2 - 723 15-07-01 programmable function keys assign a function key for exclusive hold (code 45). If an extension has its fixed hold key reassigned in program 15-02-06, assign a function key for system hold (code 44). Line key 1~48 0~99 (normal function code 751 by defa...
Page 756
Issue 11.0 univerge sv8100 2 - 724 hold operation system hold: to place an outside call on system hold: press hold. To pick up an outside call on system hold: press the flashing cap key. - or - if you know the specific line number, dial 672 + line number (001~200). Exclusive hold: to place an outsid...
Page 757
Univerge sv8100 issue 11.0 hold 2 - 725 single line telephone 1. Hookflash. 2. Dial 749. To pick up an outside call on exclusive hold: press flashing cap key. Single line telephone dial 759. Group hold: to place a call on hold so anyone in your department group can pick it up: 1. Press hold. 2. Dial...
Page 758
Issue 11.0 univerge sv8100 2 - 726 hold to pick up an intercom call on intercom hold: 1. Press speaker. 2. Press flashing icm ( 00) or conf..
Page 759: Hot Key-Pad
Univerge sv8100 issue 11.0 hot key-pad 2 - 727 hot key-pad description the hot key-pad feature allows the user to place a call without lifting the handset or pressing speaker. When the user dials another extension number on an idle telephone with hot key-pad enabled, the speaker lights and the inter...
Page 760
Issue 11.0 univerge sv8100 2 - 728 hot key-pad required software none related features central office calls, placing class of service dialing number preview hotline intercom voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that a...
Page 761
Univerge sv8100 issue 11.0 hot key-pad 2 - 729 operation to place an intercom call using hot key-pad: 1. The multiline terminal is idle. There is no need to press speaker. 2. Dial the extension. 3. Dialed extension rings. To place a trunk call using hot key-pad: 1. The multiline terminal is idle. Th...
Page 762
Issue 11.0 univerge sv8100 2 - 730 hot key-pad this page intentionally left blank.
Page 763: Hotel/motel
Univerge sv8100 issue 11.0 hotel/motel 2 - 731 hotel/motel description your univerge sv8100 telephone system provides hotel/motel services in addition to the many features available to business users. These hotel/motel services help you run your facility more efficiently, save you time and money and...
Page 764
Issue 11.0 univerge sv8100 2 - 732 hotel/motel unanswered wake up calls can automatically call the operator and print on the room status printout report. Use wake up call as a meeting reminder (e.G., for convention attendees). When used with the vrs feature, the destination is a single line room tel...
Page 765
Univerge sv8100 issue 11.0 hotel/motel 2 - 733 the supported pms-u10 protocols are neax 90-k, neax 90-k with nak, neax 60-k, ktsi and ktsi with nak. Sv8100 cpu software version 3100 (3.12 or higher) is required for pva pms. The chassis to pms-u10 and pva pms connection is via the lan and an ip port ...
Page 766
Issue 11.0 univerge sv8100 2 - 734 hotel/motel room status your phone and dss console can set and monitor the status of all your guest rooms: checked in, checked out, maid required and maid in room. Maximize room usage by coordinating your cleaning staff and reservation desk. For example, you can di...
Page 767
Univerge sv8100 issue 11.0 hotel/motel 2 - 735 the current room status in program 42-02-03 cannot be checked via pcpro. When the system is configured for the vrs feature, wake up call greetings to single line room telephones are supported. Wakeup calls to multiline room telephones do not provide a w...
Page 768
Issue 11.0 univerge sv8100 2 - 736 hotel/motel the hotel/motel feature requires the cd-cp00-us be licensed for hotel. The following dial access codes can be used only if the cd-cp00-us is licensed for the hotel/motel feature: dial access codes that require cd-cp00-us hotel license program dial acces...
Page 769
Univerge sv8100 issue 11.0 hotel/motel 2 - 737 for sv8100 systems with version 4000 or higher system software and has been migrated from a ux5000, table 2-35 migration supported blades defines the application blades supported in current system chassis. Refer to the tables below for valid status code...
Page 770
Issue 11.0 univerge sv8100 2 - 738 hotel/motel default settings not enabled system availability terminals all terminals required component(s) dss console when using the pva pms the following licenses affect this feature: sv8100 hotel/motel license: lk-sys-hm-lic (feature code 0007) this license is r...
Page 771
Univerge sv8100 issue 11.0 hotel/motel 2 - 739 um8000 hotel/motel license: lks-ums-hotel-pms-lic (feature code 1407) this license is only required when using the um8000 mail hotel features such as pms integration and hotel guest room mailboxes. When using a pms-u10 the following licenses affect this...
Page 772
Issue 11.0 univerge sv8100 2 - 740 hotel/motel guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature program...
Page 773
Univerge sv8100 issue 11.0 hotel/motel 2 - 741 11-14-03 service code setup (for hotel) – set dnd for other extension customize the set dnd for other extension used with the hotel/ motel feature (cd-cp00-us must be licensed for hotel/motel). Mlt, slt (default = 629) 11-14-04 service code setup (for h...
Page 774
Issue 11.0 univerge sv8100 2 - 742 hotel/motel 11-14-14 service code setup (for hotel) – room status change for own extension customize the room status change for own extension service codes used with the hotel/motel feature (cd-cp00-us must be licensed for hotel/motel). Mlt, slt (default = 640) 11-...
Page 775
Univerge sv8100 issue 11.0 hotel/motel 2 - 743 20-13-13 class of service options (supplementary service) – continued dialing (dtmf) signal on icm call turn off or on an extension user ability to use continued dialing, which allows dtmf signal sending while talking on extension. 0 = off 1 = on (defau...
Page 776
Issue 11.0 univerge sv8100 2 - 744 hotel/motel 42-01-01 system options for hotel/motel – answering message mode for wake up call (hotel mode) assign the answering message mode for wake up call options for hotel/motel service. 0 = moh (hold time) 1 = vrs message 2 = vrs message + time (default = 0) 4...
Page 777
Univerge sv8100 issue 11.0 hotel/motel 2 - 745 42-02-02 hotel/motel telephone setup – toll restriction class when check in assign an extension toll restriction class when it is checked in. The system has 15 toll restriction classes (1~15). The entry you make in this option affects the telephone in a...
Page 778
Issue 11.0 univerge sv8100 2 - 746 hotel/motel 42-03-05 class of service options (hotel/ motel) – wake up call setting for other extension set the hotel/motel wake up call setting for other extension cos options. 0 = off 1 = on (default = 0 for cos 1~15) 42-03-06 class of service options (hotel/ mot...
Page 779
Univerge sv8100 issue 11.0 hotel/motel 2 - 747 42-05-02 hotel room status printer – output destination number set the lan port to output the hotel data (check-out sheet, room status, etc.) and the output destination number options for the hotel/ motel feature. Up to eight digits (extension number wh...
Page 780
Issue 11.0 univerge sv8100 2 - 748 hotel/motel refer to the univerge sv8100 hotel/motel services manual for complete programming information. Operation refer to the univerge sv8100 hotel/motel services manual for complete operation information. 42-06-08 pms service setting – status for check-out aut...
Page 781: Hotline
Univerge sv8100 issue 11.0 hotline 2 - 749 hotline description hotline gives a multiline terminal user one-button calling and transfer to another extension (the hotline partner). Hotline helps co-workers that work closely together. The hotline partners can call or transfer calls to each other just b...
Page 782
Issue 11.0 univerge sv8100 2 - 750 hotline a hotline is a uniquely programmed function key. Default setting disabled related features automatic call distribution (acd) distinctive ringing, tones and flash patterns direct station selection (dss) console do not disturb handsfree answerback/forced inte...
Page 783
Univerge sv8100 issue 11.0 hotline 2 - 751 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programming...
Page 784
Issue 11.0 univerge sv8100 2 - 752 hotline 20-08-19 class of service options (outgoing call service) – hotline for spk turn off or on an extension user ability to press speaker to activate hotline or ringdown. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-06 class of service options (hold/ transfe...
Page 785
Univerge sv8100 issue 11.0 hotline 2 - 753 30-05-06 dss console lamp table – acd agent log out (acd dss) define the led patterns for acd agents that are logged out on the dss consoles. 0~7 [default = 5 (il)] 30-05-07 dss console lamp table – acd agent log in (acd dss) define the led patterns for acd...
Page 786
Issue 11.0 univerge sv8100 2 - 754 hotline operation to place a call to your hotline partner: 1. Press the hotline key (program 15-07 or sc 751: 01 + partner’s extension number). You can optionally lift the handset after this step for privacy. To transfer your outside call to your hotline partner: 1...
Page 787: Howler Tone Service
Univerge sv8100 issue 11.0 howler tone service 2 - 755 howler tone service description howler tone service provides a howler tone when a station remains off-hook after a call is completed or when a station is off-hook and digits are not dialed in a programmed time. Conditions howler tone is generate...
Page 788
Issue 11.0 univerge sv8100 2 - 756 howler tone service guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 789: Intercom
Intercom 2 - 757 i intercom description intercom gives extension users access to other extensions. This provides the system with complete internal calling ability. Handsfree answerback/forced intercom ringing handsfree answerback permits an extension user to respond to a voice-announced intercom cal...
Page 790
Issue 11.0 univerge sv8100 2 - 758 intercom for a station to retrieve a held icm call, the station must have an icm key assigned in program 15-07 (*00). With version 7000 or higher software, a special ringtone is provided when a pre-assigned extension places an intercom call. The incoming ringtone f...
Page 791
Univerge sv8100 issue 11.0 intercom 2 - 759 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmin...
Page 792
Issue 11.0 univerge sv8100 2 - 760 intercom 20-06-01 class of service for extensions assign class of service (1~15) for extensions. Day night/mode: 1~8 class of service of extensions (1~15) default: extension port 101 = class 15 all other extension port = class 1 20-08-01 class of service options (o...
Page 793
Univerge sv8100 issue 11.0 intercom 2 - 761 handsfree answerback/forced intercom ringing: 82-01-03 incoming ring tone – modulation customize the intercom ring tone modulation if desired. 0 = no modulation 1 = 8hz modulation 2 = 16hz modulation 3 = envelope (default = 2) program number program name d...
Page 794
Issue 11.0 univerge sv8100 2 - 762 intercom 80-01-02 service tone setup – basic tone number define up to 64 service tones. Each service tone is defined by the combination of 32 basic tones. 1~33 (0 = no tone) (33=default time slot) refer to table 2-34 service tone setup, program 80-01-02 on page 2-7...
Page 795
Univerge sv8100 issue 11.0 intercom 2 - 763 operation to place an intercom call: 1. At multiline terminal, press speaker. - or - at single line telephone, lift the handset. 2. Dial extension number (or 0 for your operator). Your call may voice-announce or ring the called extension. Dial 1 to change ...
Page 796
Issue 11.0 univerge sv8100 2 - 764 intercom to change how intercom calls ring the extension: 1. Press speaker or lift the handset. 2. Dial 723 to have calls ring your extension. - or - 3. Dial 721 to have calls voice announce to your extension..
Page 797: Ip Multiline Station (Sip)
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 765 ip multiline station (sip) enhancements the same user name and password can be assigned to ip multiline station, mh240 and desktop portswhen automatic or manual registration is used (version 3000 or higher software). With version 3000 or ...
Page 798
Issue 11.0 univerge sv8100 2 - 766 ip multiline station (sip) description the univerge sv8100 system supports ip extensions using a variety of multiline terminals. These telephones have the same look and functionality of typical multiline telephones, but they are connected to the ccpu via ip rather ...
Page 799
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 767 power save adapter (psa-l unit) the power save adapter is an add-on module for the ip (dt700) and digital (dt300) multiline telephones. The psa-l unit allows connection to an analog trunk if the power or system connection were to fail, or...
Page 800
Issue 11.0 univerge sv8100 2 - 768 ip multiline station (sip) power patch panel the powered patch panel has two rj-45 connectors per ip telephone. One port connects to the switch and the other port connects to the ip telephone. The patch panel contains an integral power supply, adding power to the s...
Page 801
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 769 although the peer to peer feature is supported for ip station-to-ip station calls, the univerge sv8100 chassis must still have a registered pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb installed in the system. With barge-in, a short ...
Page 802
Issue 11.0 univerge sv8100 2 - 770 ip multiline station (sip) multiple logon with version 3000 or higher software, the same user name and password can be assigned to multiple extensions when using automatic or manual registration. This makes it easier on the user by only having to remember one passw...
Page 803
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 771 ip multiline stations must register with the ip address of the ipla/iplb. The ip multiline stations registering via a url is not supported. If an internal paging group has only ip multiline stations, mutlicast is used for the page. Ip mul...
Page 804
Issue 11.0 univerge sv8100 2 - 772 ip multiline station (sip) restrictions when using dt700 ip phones, assigning the following features to a large number of phones (30 or more) is not recommended: the same trunk line assignment (squared key system) the same virtual extension assignment paging key wi...
Page 805
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 773 system availability terminals all ip multiline terminals required software none required component(s) cpu with pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb daughter board installed napt traversal description napt (network address por...
Page 806
Issue 11.0 univerge sv8100 2 - 774 ip multiline station (sip) with version 6000 or higher software installed, the new napt feature is only effective when program15-05-45 is set “1” (on). Refer to figure 2-20 example – nat traversal or an examples of the nat traversal network. Table 2-40 example – re...
Page 807
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 775 conditions the router the sv8100 resides behind requires port forwarding statements. With version 6000 or higher software, when program 15-05-45 is set to “1” the manual table setting for port forwarding may not be required on the remote ...
Page 808
Issue 11.0 univerge sv8100 2 - 776 ip multiline station (sip) after starting sip negotiation for the call, if any rtp packet can’t be received from the terminal within 10 seconds, the call is dropped and the ip terminal displays the following: default setting none system availability terminals dt700...
Page 809
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 777 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for ...
Page 810
Issue 11.0 univerge sv8100 2 - 778 ip multiline station (sip) 10-12-10 cd-cp00-us network setup – subnet mask set the subnet mask of the ipla. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 255.2...
Page 811
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 779 10-46-01 dt700 server information setup – register mode normal mode: when the phone boots up, it reports the ext. Assigned in the phone or chooses the next available extension in the system. No password is required. Auto mode: if set to a...
Page 812
Issue 11.0 univerge sv8100 2 - 780 ip multiline station (sip) 84-10-01 tos setup – tos mode when input data is set to 1, protocol 7 is invalid. When data is set to 2, protocols 2~6 are invalid. 0 = disable (invalid) 1 = ip precedence 2 = diffserv (default = 0) 84-10-07 tos setup – priority (d.S.C.P....
Page 813
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 781 84-22-04 dt700 multiline logon information setup – log off when the registration mode (10-46-01) is set to manual, and the phone prompts for a login, the previous user id appears so the user only has to enter the password. When enabled, t...
Page 814
Issue 11.0 univerge sv8100 2 - 782 ip multiline station (sip) ip multiline station (sip) with napt: program number program name description/comments assigned data level 1 2 3 10-12-03 cd-cp00-us network setup – default gateway assign the default gateway ip address for the cd-cp00-us. 0.0.0.0~ 126.25...
Page 815
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 783 10-12-10 cd-cp00-us network setup – subnet mask set the subnet mask of the ipla/ iplb. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0...
Page 816
Issue 11.0 univerge sv8100 2 - 784 ip multiline station (sip) 10-58-01 network address – network address this program sets the local area network of the dt700 terminal when the system has a nat router and a local router. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 191.254.255.254 192.0.0.1~ 223.255.255.254 ...
Page 817
Univerge sv8100 issue 11.0 ip multiline station (sip) 2 - 785 nat traversal: 84-26-02 ipl basic setup – rtp port number assign the rtp port number to be used for each dsp on the ipla/ iplb. Only even numbered ports are supported. 0~65534 defaults: voip gw1 = 10020 voip gw2 = 10052 voip gw3 = 10084 v...
Page 818
Issue 11.0 univerge sv8100 2 - 786 ip multiline station (sip) in addition to the above programming, define the programming options as required for the system features. Refer to the univerge sv8100 programming manual and the univerge sv8100 networking manual for programming details. Operation refer t...
Page 819
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 787 ip multiline station (sip) – ml440 cordless description many smb businesses, understanding the impact of a mobile workforce, are rapidly defining their requirements for enabling effective communications and information ac...
Page 820
Issue 11.0 univerge sv8100 2 - 788 ip multiline station (sip) – ml440 cordless the ml440 has two sets of keys: three soft keys that are dedicated depending on the state of the call and four programmable keys. The three dedicated soft keys are predefined depending on the state of the call. For exampl...
Page 821
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 789 supported system feature list headset yes backlit for keys yes volume key up/down yes mute key yes soft keys based on status call yes hold conference transfer centralized directory yes feature name ml440 comment account c...
Page 822
Issue 11.0 univerge sv8100 2 - 790 ip multiline station (sip) – ml440 cordless call forwarding – centrex yes call forwarding with follow me yes call forwarding with park and page yes no recording beep is provided to handset user when setting up greetings. Call forwarding, all, bna, busy and both rin...
Page 823
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 791 desktop suite no dial pad confirmation tone no dial tone detection no dialing number preview no this is a function of the ml-440 handset. Dialing inward dialing (did) yes direct inward line (dil) yes direct inward system ...
Page 824
Issue 11.0 univerge sv8100 2 - 792 ip multiline station (sip) – ml440 cordless intercom yes ip multiline station (sip) yes ip trunk – (sip) session initiation protocol n/a ip trunk – h.323 yes isdn compatibility yes k-ccis – ip yes k-ccis – t1 yes last number redial no call redial function is a func...
Page 825
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 793 paging, internal yes a ml-440 can only initiate an internal, external or all call page. It cannot receive either internal or all call pages or display page information. Park yes pbx compatibility yes pc programming yes pe...
Page 826
Issue 11.0 univerge sv8100 2 - 794 ip multiline station (sip) – ml440 cordless softkeys no ml-440 handset softkeys are fixed and do not follow sv8100 softkey settings. Speed dial – group yes group speed dial bins are only available using function line key (28). Speed dial – system no speed dial – st...
Page 827
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 795 conditions the maximum number of ml440 handsets that can register to one ap20 access point is 30. The maximum number of ml440 handsets supported in one sv8100 system is 200. The maximum number of ap20 access points suppor...
Page 828
Issue 11.0 univerge sv8100 2 - 796 ip multiline station (sip) – ml440 cordless the sv8100 requires one ip terminal license (5101) per ml440 handset. The ml440 and ap20 system software is upgraded over-the-air direct to handsets and access points. The ap20 can only be powered using power over etherne...
Page 829
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 797 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and we...
Page 830
Issue 11.0 univerge sv8100 2 - 798 ip multiline station (sip) – ml440 cordless 10-12-10 cd-cp00-us network setup – subnet mask set the subnet mask of the ipla/ iplb. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.24...
Page 831
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 799 15-07-01 programmable function keys assign functions to multiline terminal line keys. Nec recommends the following for the first three programmable keys: line keys 1 and 2 = cap keys line key 3 = intercom key line key 1~4...
Page 832
Issue 11.0 univerge sv8100 2 - 800 ip multiline station (sip) – ml440 cordless 24-09-03 call forward split settings - intercom call forwarding destination for both ring, all call, no answer assign intercom call forwarding destination for ring, all call and no answer. 1~9, 0, #, , r, @ (up to 24 dig...
Page 833
Univerge sv8100 issue 11.0 ip multiline station (sip) – ml440 cordless 2 - 801 operation refer to the ml440 user guide for detailed operation information. 84-26-03 ipl basic setup – rtcp port number (rtp port number + 1) define the udp port number for rtcp to use for each dsp. 0~65534 defaults: voip...
Page 834
Issue 11.0 univerge sv8100 2 - 802 ip multiline station (sip) – ml440 cordless this page intentionally left blank.
Page 835
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 803 ip single line telephone (sip) description sip (session initiation protocol) is used for voice over internet protocol. It is defined by the ietf (internet engineering task force) rfc3261. Other rfc designations, such as rfc3842, refer...
Page 836
Issue 11.0 univerge sv8100 2 - 804 ip single line telephone (sip) the ipla/iplb supports only those codecs that are considered to provide toll-quality equivalent speech path. The following voice compression methods are supported for the ip station sip feature: g.711 -law – highest bandwidth g.722 – ...
Page 837
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 805 duplex mode (auto, full, or half) and speed (10 or 100 mbps) are configured via sv8100 chassis programming. The iplb does not support half duplex, it only supports full duplex. Univerge sv8100 supports a 100 rel option and session tim...
Page 838
Issue 11.0 univerge sv8100 2 - 806 ip single line telephone (sip) standard sip video codecs are not supported across netlink. Standard sip terminal can not negotiate video codec with sp310. Sip protocol (rfc3261) is used. Sip station uses the pz-( )ipla/iplb as a media gateway. Default udp listen po...
Page 839
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 807 nat or napt is only supported on the dt700 series phones. Nat or napt is not supported on the ml440, mh240, the wireless dect (sip), sp310 or third party sip phones. Table 2-44 feature support table for standard sip device feature nam...
Page 840
Issue 11.0 univerge sv8100 2 - 808 ip single line telephone (sip) data line security yes barge-in is not supported. Dialing number preview yes directed call pickup yes direct inward dialing (did) yes direct inward line (dil) yes door box yes door box will not ring a sip device. A sip device can call...
Page 841
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 809 microphone cutoff yes microphone cutoff is a function of the sip device. Multiple trunk types yes music on hold yes netlink yes operator yes paging, external yes a sip device can only initiate an internal, external or all call page. I...
Page 842
Issue 11.0 univerge sv8100 2 - 810 ip single line telephone (sip) transfer yes transferred calls cannot be pulled back once transfer is initiated. Trunk groups yes trunk group routing yes uniform numbering network yes um8000 yes vm8000 inmail yes voice mail integration (analog) yes voice over intern...
Page 843
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 811 call forwarding with follow me no call forwarding – park and page no call forwarding/do not disturb override no call forwarding, off-premise no call monitoring no call redirect no call waiting/camp-on no clock/calendar display no code...
Page 844
Issue 11.0 univerge sv8100 2 - 812 ip single line telephone (sip) d term cordless ii terminal no d term cordless lite ii terminal no d term handset cordless no d term ip gateway system no e911 compatibility no electra elite terminal migration no facsimile co branch connection no flash no forced trun...
Page 845
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 813 programmable function keys no programming from a multiline terminal no pulse to tone conversion no redial function no call redial function is a function of the client device and not the system. Repeat redial no reverse voice over no r...
Page 846
Issue 11.0 univerge sv8100 2 - 814 ip single line telephone (sip) default setting none system availability terminals sip terminals compliant with rfc 3261, rfc 3262, rfc 3264 (session description protocol), rfc 1889 (real time protocol). Required components cd-cp00-us pz-32ipla/iplb, pz-64ipla/iplb ...
Page 847
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 815 related features none std sip transfer–unattended description with version 6000 or higher software, any standard sip terminal can perform an unattended (blind/ unsupervised) transfer. Refer to section 2.4 (transfer-unattended) of draf...
Page 848
Issue 11.0 univerge sv8100 2 - 816 ip single line telephone (sip) system availability terminals standard sip terminal required components cd-cp00-us pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb related features ip single line telephone (sip) transfer guide to feature programming the level 1, le...
Page 849
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 817 10-12-09 cd-cp00-us network setup – ip address set ip address for ipla/iplb. The ip address assigned in program 10-12-01 cannot start with the same leading digits as the ip address assigned here. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 19...
Page 850
Issue 11.0 univerge sv8100 2 - 818 ip single line telephone (sip) 10-19-01 voip dsp resource selection select type of ipla/iplb dsp resource. This program setting has no affect on the terminal/trunk port assignment or usage. 0 = common use for both ip extensions and trunks 1 = ip extension 2 = sip t...
Page 851
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 819 voip tos setup: the univerge sv8100 supports quality of service (qos) marking for the session initiation protocol (sip). Ip extension numbering: sip extension codec information: 84-06-09 pva data setting – delay lsr threshold define t...
Page 852
Issue 11.0 univerge sv8100 2 - 820 ip single line telephone (sip) 84-19-02 sip extension codec information basic setup – g.711 voice activity detection mode enable/ disable voice activity detection for g.711. 0 = disable 1 = enable (default = 0) 84-19-03 sip extension codec information basic setup –...
Page 853
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 821 84-19-18 sip extension codec information basic setup – vad threshold define the vad threshold – values set in db. Consult the univerge sv8100 programming manual for threshold scale to set acceptable values. 0~30 (default = 20) 84-19-2...
Page 854
Issue 11.0 univerge sv8100 2 - 822 ip single line telephone (sip) 84-19-34 sip extension ip codec information basic setup – g.722 voice activity detection mode enable/disable g.722 voice activity detection mode. 0 = disable 1 = enable (default = 0) 84-19-35 sip extension ip codec information basic s...
Page 855
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 823 84-19-52 sip extension ip codec information basic setup – fax maximum rate sets the maximum fax rate. 0 = v.27ter, 2400bps 1 = v.27ter, 4800bps 2 = v.29, 7200bps 3 = v.29, 9600bps 4 = v.17, 12000bps 5 = v.17, 14400bps (default = 5) 84...
Page 856
Issue 11.0 univerge sv8100 2 - 824 ip single line telephone (sip) sip extension basic information setup: program number program name description/comments assigned data level 1 2 3 84-20-01 sip extension basic information setup – registrar/proxy port define sip station proxy port. 1~65535 (default = ...
Page 857
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 825 ip phone configuration: program number program name description/comments assigned data level 1 2 3 15-01-01 basic extension data setup – extension name define the extension/virtual extension name. Up to 12 characters default: sta 101 ...
Page 858
Issue 11.0 univerge sv8100 2 - 826 ip single line telephone (sip) std sip transfer – unattended: sip phone example: 15-05-43 ip telephone terminal basic data setup – video mode enable or disable video mode for standard sip terminals. 0 = disable 1 = enable (default = 0) program number program name d...
Page 859
Univerge sv8100 issue 11.0 ip single line telephone (sip) 2 - 827 the following menu items require programming in your sip ip phone (consult sip phone vendor specific documentation): operation none program/ item no. Description/selection default assigned data comments 1 ip address 0.0.0.0 enter a st...
Page 860
Issue 11.0 univerge sv8100 2 - 828 ip single line telephone (sip) this page intentionally left blank.
Page 861
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 829 ip trunk – (sip) session initiation protocol description the univerge sv8100 ip trunk sip package sends the real time voice over the corporate lan or wan. The voice from the telephone is digitized and then put into frame...
Page 862
Issue 11.0 univerge sv8100 2 - 830 ip trunk – (sip) session initiation protocol depending on the requirements and resource allocation in the lan/wan/internet, the pz-( )ipla/ iplb - sip can be configured to use any of the following voice compressions: g.711 -law – highest bandwidth g.729 (a) – most...
Page 863
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 831 system availability terminals all multiline terminals required component(s) none sip trunk e.164 support description with sip trunk e.164 support enabled, the pbx is able to support sip configurations where the number pr...
Page 864
Issue 11.0 univerge sv8100 2 - 832 ip trunk – (sip) session initiation protocol conditions minimum of sv8100 main system software version 7000 or higher is required. E.164 support is applied on the sip trunk interface. E.164 is supported for all carrier choices (program 10-29-14). Netlink multi-carr...
Page 865
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 833 sip trunk e.164 clip enhancement description with the sip trunk e.164 clip enhancement enabled, when an incoming sip call from an external itsp is presented at the system with a + in the from header field as the internat...
Page 866
Issue 11.0 univerge sv8100 2 - 834 ip trunk – (sip) session initiation protocol required component(s) cd-cp00-us ipla/ iplb ip trunk license related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this featu...
Page 867
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 835 10-12-05 cd-cp00-us network setup – nic interface set up the nic interface. 0 = auto detect 1 = 100mbps, full duplex 2 = 100mbps, half duplex 3 = 10mbps, full duplex 4 = 10mbps, half duplex (default = 0) 10-12-06 cd-cp00...
Page 868
Issue 11.0 univerge sv8100 2 - 836 ip trunk – (sip) session initiation protocol 10-12-10 cd-cp00-us network setup – subnet mask define the media gateway subnet mask address. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0....
Page 869
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 837 10-19-01 voip dsp resource selection select type of ipla/iplb dsp resource. This program setting has no affect on the terminal/trunk port assignment or usage. 0 = common use for both ip extensions and trunks 1 = ip exten...
Page 870
Issue 11.0 univerge sv8100 2 - 838 ip trunk – (sip) session initiation protocol 10-28-05 sip system information setup – domain assignment define the domain assignment. This entry is determined by what information the sip carrier provides. If the sip carrier provides a server name: sipconnect-sca@l0....
Page 871
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 839 10-29-06 sip server information setup – registrar ip address define the registrar ip address. The carrier may provide an ip address. In most cases, a domain name is used so this entry is left at the default. 0.0.0.0~ 126...
Page 872
Issue 11.0 univerge sv8100 2 - 840 ip trunk – (sip) session initiation protocol 10-30-03 sip authentication information – password enter the authentication password provided by the sip carrier. When the univerge sv8100 registers its own id with the carrier sip server or makes an outgoing call via th...
Page 873
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 841 11-01-01 system numbering – service code set the system internal (intercom) numbering plan. The numbering plan assigns the first and second digits dialed and affects the digits an extension user must dial to access other...
Page 874
Issue 11.0 univerge sv8100 2 - 842 ip trunk – (sip) session initiation protocol 22-02-01 incoming call trunk setup assign the incoming trunk type for each trunk. Trunks 1~200 0 = normal 1 = vrs (second dial tone if no vrs installed) 2 = disa 3 = did 4 = dil 5 = e&m tie line 6 = delayed vrs 7 = ani/d...
Page 875
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 843 84-06-02 pva data setting – rtcp port number define the media gateway starting rtcp port number . The rtcp port number must be the (rtp port number + 1). Rtp port number + 1 (default = 10021) 84-06-04 pva data setting – ...
Page 876
Issue 11.0 univerge sv8100 2 - 844 ip trunk – (sip) session initiation protocol 84-10-05 tos setup – high reliability 1 = optimize for reliability routing. 0~1 0 = normal reliability 1 = low reliability (default = 0) 84-10-07 tos setup – priority (d.S.C.P. - differentiated services code point) dscp ...
Page 877
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 845 84-13-11 sip trunk codec information basic setup – g.729 jitter buffer (max) set the maximum g.729 jitter buffer. 0~270ms (default = 80) 84-13-17 sip trunk codec information basic setup – jitter buffer mode set the jitte...
Page 878
Issue 11.0 univerge sv8100 2 - 846 ip trunk – (sip) session initiation protocol 84-13-31 sip trunk codec information basic setup – dtmf payload number define the dtmf payload number. 96~127 (default = 110) 84-13-32 sip trunk codec information basic setup – dtmf relay mode determine the dtmf setup. 0...
Page 879
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 847 84-13-49 sip trunk codec information basic setup – rtp filter to avoid incorrect voice pass connection, this program checks the sending side address from received rtp packet at voipdb. 0 = disable 1 = enable (default = 0...
Page 880
Issue 11.0 univerge sv8100 2 - 848 ip trunk – (sip) session initiation protocol 84-13-61 sip trunk codec information basic setup – t.38 rtp format payload number sets the payload number for t.38 rtp format. 96~127 (default = 100) 84-14-06 sip trunk basic information setup – sip trunk port number set...
Page 881
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 849 sip trunk e.164 support 84-26-03 ipl basic setup – rtcp port number (rtp port number + 1) define the tcp port number for rtcp to use for each dsp. 0~65534 defaults: voip gw1 = 10021 voip gw2 = 10053 voip gw3 = 10085 voip...
Page 882
Issue 11.0 univerge sv8100 2 - 850 ip trunk – (sip) session initiation protocol sip trunk e.164 clip enhancement 84-14-13 sip trunk basic information setup – incoming/ outgoing sip trunk for e.164 when this data is set to 1, then for any outbound sip calls a + is added as a prefix to the request- ur...
Page 883
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 851 operation sip trunk e.164 support: to make a call using e.164 number format: 1. Lift the handset or press speaker. 2. Dial 00441202223344 # . The system automatically modifies the required header fields of the sip invite...
Page 884
Issue 11.0 univerge sv8100 2 - 852 ip trunk – (sip) session initiation protocol sip trunk e.164 clip enhancement delete the + only from an incoming sip invite using e.164 numbering scheme: incoming call from: +4902131795770 displayed in terminal incoming caller history as: table 2-45 sip invite head...
Page 885
Univerge sv8100 issue 11.0 ip trunk – (sip) session initiation protocol 2 - 853 delete and replace the + and matched country code from an incoming sip invite using e.164 numbering scheme: incoming call from: +4902131795770 program 10-02-02 = 00 displayed in terminal incoming caller history as: delet...
Page 886
Issue 11.0 univerge sv8100 2 - 854 ip trunk – (sip) session initiation protocol incoming call from: +4902131795770 program 10-02-02 = 00 program 10-02-03 = 9 displayed in terminal incoming caller history as: making an outgoing call from history of incoming calls: 1. From an idle multiline terminal. ...
Page 887: Ip Trunk – H.323
Univerge sv8100 issue 11.0 ip trunk – h.323 2 - 855 ip trunk – h.323 description h.323 is an international telecommunication union (itu) standard for packet based multimedia communication systems. The univerge sv8100 can use h.323 to connect to another univerge sv8100 system or a third-party product...
Page 888
Issue 11.0 univerge sv8100 2 - 856 ip trunk – h.323 g 722 this codec is useful in fixed network, voice over ip applications, where the required bandwidth is typically not prohibitive. G.723 this codec is a itu-t standard wide band speech codec. This is an extension of recommendation g.721 adaptive d...
Page 889
Univerge sv8100 issue 11.0 ip trunk – h.323 2 - 857 guide to feature programming the level 1, level 2 and level 2 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pr...
Page 890
Issue 11.0 univerge sv8100 2 - 858 ip trunk – h.323 10-12-10 cd-cp00-us network setup – subnet mask define the media gateway subnet mask address. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 25...
Page 891
Univerge sv8100 issue 11.0 ip trunk – h.323 2 - 859 10-23-01 sip system interconnection setup – system interconnection determine if the system is interconnected to another system. 0 = no (disable) 1 = yes (enable) (default = 0) 10-23-02 sip system interconnection setup – ip address define the ip add...
Page 892
Issue 11.0 univerge sv8100 2 - 860 ip trunk – h.323 20-09-02 class of service options (incoming call service) – caller id display turn off or on the caller id display at an extension. 0 = off 1 = on (default = 0 for cos 1~15) 21-17-01 ip trunk (sip) calling party number setup for trunk assign the ca...
Page 893
Univerge sv8100 issue 11.0 ip trunk – h.323 2 - 861 44-02-03 dial analysis table for ars/ f-route access – additional data if a service type is selected in program 44-02-02, set the additional data, if required, for the pre-transaction table for selecting ars/f-route (24 digits max: 1~9, 0 # , @)....
Page 894
Issue 11.0 univerge sv8100 2 - 862 ip trunk – h.323 84-01-11 h.323 trunk basic information setup – number of g.723 audio frames define the number of g.723 audio frames for h.323. 1~2 (default = 1) 84-01-12 h.323 trunk basic information setup – g.723 vad mode define the g.723 vad mode for h.323. 0 = ...
Page 895
Univerge sv8100 issue 11.0 ip trunk – h.323 2 - 863 84-01-25 h.323 trunk basic information setup – echo canceller tail size define the echo canceller tail size for h.323. 1 = 4ms 2 = 8ms 3 = 16ms 4 = 32ms 5 = 64ms 6 = 128ms (default = 6) 84-01-26 h.323 trunk basic information setup – echo canceller ...
Page 896
Issue 11.0 univerge sv8100 2 - 864 ip trunk – h.323 84-01-41 h.323 trunk basic information setup – fax communication no communication time-out define the fax communication no communication time-out for h.323. 10~32000 seconds (default = 30) 84-01-43 h.323 trunk basic information setup – high-speed s...
Page 897
Univerge sv8100 issue 11.0 ip trunk – h.323 2 - 865 84-01-54 h.323 trunk basic information setup – nsf superscription define the nsf superscription for h.323. 0 = disable 1 = enable (default = 0) 84-01-55 h.323 trunk basic information setup – ecm (error correction mode) define the ecm (error correct...
Page 898
Issue 11.0 univerge sv8100 2 - 866 ip trunk – h.323 operation none 84-01-66 h.323 trunk basic information setup – g.722 jitter buffer (average) define the g.722 jitter buffer (average) for h.323. 0~160ms (default = 60) 84-01-67 h.323 trunk basic information setup – g.722 jitter buffer (max) define t...
Page 899: Ipk/ipk II Migration
Univerge sv8100 issue 11.0 ipk/ipk ii migration 2 - 867 ipk/ipk ii migration description the ipk/ipk ii migration package allows the user of an existing nec ipk/ipk ii platform to utilize the enhanced capabilities of the sv8100. Conditions in a netlink environment, ipk/ipk ii migration can only be u...
Page 900
Issue 11.0 univerge sv8100 2 - 868 ipk/ipk ii migration when adding or removing padding for trunks, use program 14-01 for all trunks except the pri trunks in a migration cabinet. Use program 81-12 to add or remove padding for pri trunks in a migration cabinet. Sv8100 uc desktop suite applications an...
Page 901
Univerge sv8100 issue 11.0 ipk/ipk ii migration 2 - 869 multiple sv8100 to ipk/ipk ii chassis connectivity in addition to the cabinet/chassis layout shown above, with version 4000 (4.01) or higher software the following configurations are also supported: layout 1: refer to figure 2-24 multiple sv810...
Page 902
Issue 11.0 univerge sv8100 2 - 870 ipk/ipk ii migration layout 2: refer to figure 2-25 multiple sv8100 to ipk/ipk ii connection (layout 2) . Two cables are connected to the mgn-u10 etu and one cable connected to the (pz-bs11). Slot layout: slot 1 ~ 6: 1st sv8100 chassis slots 1 ~ 6 slot 7 ~ 17: 1st ...
Page 903
Univerge sv8100 issue 11.0 ipk/ipk ii migration 2 - 871 layout 3: refer to figure 2-26 multiple sv8100 to ipk/ipk ii connection (layout 3) . Two cables are connected to the mgn-u10 etu and one cable connected to the (pz-bs11). Slot layout: slot 1 ~ 6: 1st sv8100 chassis slots 1 ~ 6 slot 7 ~ 11: 1st ...
Page 904
Issue 11.0 univerge sv8100 2 - 872 ipk/ipk ii migration table 2-49 ipk ii supported hardware package name description supported exp exp-u10 expansion unit y esi esi(8)-u10 8-port electronic station interface y esib(8)/esie(8)-u10 8-port electronic station interface y esib(8)/esie(8)-u20 8-port elect...
Page 905
Univerge sv8100 issue 11.0 ipk/ipk ii migration 2 - 873 table 2-50 supported optional equipment (via mgn-u10 etu) provides a listing of the dtu/dtp and dth/dtr optional equipment supported for terminals connected to the ipk/ipk ii ksu’s. Isdn brt-u20 (f/w ver. 4.0 or later) isdn interface y dti-u40 ...
Page 906
Issue 11.0 univerge sv8100 2 - 874 ipk/ipk ii migration table 2-51 supported optional equipment provides a listing of the dt300 optional equipment supported for terminals connected to the sv8100 chassis. Default setting disabled system availability terminals dtu/dtp series e (version 2.51 or higher)...
Page 907
Univerge sv8100 issue 11.0 ipk/ipk ii migration 2 - 875 required component(s) the mgn-u10 etu board requires the cd-cp00-us, pz-me50-us and pz-bs10 blades to be installed in the chs2u-us (19”) or chs2u b-us (9.5”) controlling chassis . Related features none guide to feature programming none operatio...
Page 908
Issue 11.0 univerge sv8100 2 - 876 ipk/ipk ii migration this page intentionally left blank.
Page 909: Ip/digital Call Logging
Univerge sv8100 issue 11.0 ip/digital call logging 2 - 877 ip/digital call logging description when using nec dt300 and dt700 desktop terminals, telephone calls can be monitored, recorded and stored. For single phone applications, the nec 1-port digital call logging unit can be used. This will only ...
Page 910
Issue 11.0 univerge sv8100 2 - 878 ip/digital call logging the nec ip/digital reporter is necs most feature rich product for listening to recorded phone calls. It has functionality much the same as the manager but offers additional features. These additional features make management easier by provid...
Page 911
Univerge sv8100 issue 11.0 ip/digital call logging 2 - 879 default setting none system availability terminals nec dt300/dt700 series desktop terminals – nec ip/digital call logging required component(s) 4-port digital call logging unit pc hardware and software: pentium 4 processor 512 mb ram microso...
Page 912
Issue 11.0 univerge sv8100 2 - 880 ip/digital call logging guide to feature programming none operation none.
Page 913: Isdn Compatibility
Univerge sv8100 issue 11.0 isdn compatibility 2 - 881 isdn compatibility description isdn-bri integrated service digital network – basic rate interface (isdn-bri) is a public switched telephone network (pstn) service that provides two b channels and a d channel (2b + d) for voice call trunking. The ...
Page 914
Issue 11.0 univerge sv8100 2 - 882 isdn compatibility isdn – bri/pri features did line service when configured for did line service, the trunks emulate loop start or ground start trunks for outgoing calls and did trunks for incoming calls. Calling line identification presentation (clip) program 10-0...
Page 915
Univerge sv8100 issue 11.0 isdn compatibility 2 - 883 speech and 3.1 khz audio pri ability requires the installation of cd-prta. Each pri circuit provides 24 pri channels (23b + d) 4 with 64k clear channel response. The t1/pri interface uses a single slot. When installed, the t1/pri interface uses t...
Page 916
Issue 11.0 univerge sv8100 2 - 884 isdn compatibility the univerge sv8100 supports receiving the name from the network in supported formats only. Refer to table 2-52 restrictions for calling party names . Co line service is not supported isdn – pri cannot be configured for co emulation b-channel to ...
Page 917
Univerge sv8100 issue 11.0 isdn compatibility 2 - 885 refer to the charts below for examples: incoming call trunk number b-channel number station user 9 1 talking on tk009 10 2 11 3 12 4 13 5 14 6 15 7 16 8 17 9 18 10 19 11 20 12 21 13 22 14 …31 …23 incoming call from the network on channel 23. In m...
Page 918
Issue 11.0 univerge sv8100 2 - 886 isdn compatibility basic rate interface (bri) caller id name to single line telephone is not supported for isdn (brt) trunks. The system is compatible with isdn basic rate interface (bri) services. Bri services currently supported include: basic bri call control (b...
Page 919
Univerge sv8100 issue 11.0 isdn compatibility 2 - 887 automatic data link failure recovery if a data link error is detected by the bri etu, the system tries to recover the data link and send the spid to the central office. To provide this enhancement, the bri etu must be able to indicate to the syst...
Page 920
Issue 11.0 univerge sv8100 2 - 888 isdn compatibility isdn 2 b-channel transfer description this isdn pri 2 b-channel transfer feature allows the univerge sv8100 to receive a call on one b-channel and transfer it back out on a second b-channel (trunk-to-trunk transfer on the telco side). When the tr...
Page 921
Univerge sv8100 issue 11.0 isdn compatibility 2 - 889 system availability terminals all terminals required component(s) to provide isdn-pri trunk connection: cd-prta to provide isdn-bri trunk connection: cd-2bria or cd-2bria with pz-2bria nt-1 for each bri (locally provided) related features central...
Page 922
Issue 11.0 univerge sv8100 2 - 890 isdn compatibility guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature ...
Page 923
Univerge sv8100 issue 11.0 isdn compatibility 2 - 891 10-03-13 etu setup (prta pkg setup) – loss of signal detection limit if the transmit/receive voltage is less than the setting in program 10-03-13, the system considers this as loss-of-signal and the pri does not come up. Note that there are diffe...
Page 924
Issue 11.0 univerge sv8100 2 - 892 isdn compatibility isdn – pri installation: program number program name description/comments assigned data level 1 2 3 10-03-04 etu setup (prta pkg setup) – layer 3 timer type set up and confirm the basic configuration data for each cd-prta this program selects the...
Page 925
Univerge sv8100 issue 11.0 isdn compatibility 2 - 893 10-03-20 etu setup (prta pkg setup) – network exchange selection select the isdn protocol for the isdn circuit. 0 = standard (same as ni-2) 1 = reserved 2 = reserved 3 = dms (a211) 4 = 5ess 5 = dms (a233) 6 = 4ess 7 = ni-2 (default = 0) 10-03-21 ...
Page 926
Issue 11.0 univerge sv8100 2 - 894 isdn compatibility did services for either isdn – bri or pri: calling party number presentation for either isdn – bri or pri: program number program name description/comments assigned data level 1 2 3 22-02-01 incoming call trunk setup assign the incoming trunk typ...
Page 927
Univerge sv8100 issue 11.0 isdn compatibility 2 - 895 15-01-04 basic extension data setup – isdn caller id if program 15-01-04 and program 10-03-05 are enabled, the system includes caller id in the setup message as presentation allowed. If these options are disabled, it is presentation restricted. 0...
Page 928
Issue 11.0 univerge sv8100 2 - 896 isdn compatibility isdn – pri network specific assignment: smdr dialed digits for either isdn – bri or pri: program number program name description/comments assigned data level 1 2 3 26-02-07 dial analysis table for ars/lcr – network specified parameter table defin...
Page 929
Univerge sv8100 issue 11.0 isdn compatibility 2 - 897 general isdn programs: 35-02-16 smdr output options – trunk name or received dialed number determine how the smdr should print incoming calls on ani/dnis or did trunks. If set to 1, ani/dnis trunks can print dnis digits, if set to 0 trunk names a...
Page 930
Issue 11.0 univerge sv8100 2 - 898 isdn compatibility isdn 2 b-channel transfer: 20-09-03 class of service options (incoming call service) – sub address identification define whether or not an extension displays the caller sub- address. 0 = deny 1 = allow (default = 0 for cos 1~15) 20-11-11 class of...
Page 931
Univerge sv8100 issue 11.0 isdn compatibility 2 - 899 operation to perform an isdn 2 b-channel transfer: 1. Receive or make an isdn trunk call. 2. Go off-hook using the handset, or press speaker (the call appearance key or direct trunk appearance lights). Talk with the outside party. 3. Press the tr...
Page 932
Issue 11.0 univerge sv8100 2 - 900 isdn compatibility 5. Dial the outside number and wait for the outside party to answer. 6. Hang up. 7. Lcd returns to idle after the lcd display hold timeout (program 20-02-08)..
Page 933
Univerge sv8100 issue 11.0 isdn compatibility 2 - 901 programming flowchart for isdn-pri – answering calls start in 10-03-01, determine the mode of the dti( )-u40 etu (0=not set, 1=t-bus) in 10-03-03, enter '0'. In 10-03-03, enter '1'. In 10-03-04, select the layer 3 timer type (1-5). The timer valu...
Page 934
Issue 11.0 univerge sv8100 2 - 902 isdn compatibility should the sub-address id be displayed for incoming calls? Is smdr used? In 20-09-03, set the extension's cos to '1'. In 20-09-03, set the extension's cos to '0'. In 35-02-16, enter '0' to print the trunk port name assigned in 14-01-01 or enter '...
Page 935
Univerge sv8100 issue 11.0 isdn compatibility 2 - 903 b do you want unanswered pri calls to reroute if unanswered? In 22-01-04, enter 0. In 22-01-04, enter 0. Reroute do not reroute in 22-08-01, enter the no-answer ring group for unanswered pri calls. In 22-04-01, assign extension to pri trunk's rin...
Page 936
Issue 11.0 univerge sv8100 2 - 904 isdn compatibility programming flowchart of isdn-pri – placing calls start in 10-03-01, determine the mode of the cd-prta (0=not set, 1=t-bus). In 10-03-03, enter '0'. In 10-03-03, enter '1'. In 10-03-04, select the layer 3 timer type (1-5). The timer value is set ...
Page 937
Univerge sv8100 issue 11.0 isdn compatibility 2 - 905 a should caller id be included in the call's setup message? In 15-01-04, enter 1 in 10-03-05 enter 1. In 15-01-04, enter 0 in 10-03-05 enter 0 no yes in 21-12-01, program the calling party number data (15 digits max.) for each trunk. In 20-06-01,...
Page 938
Issue 11.0 univerge sv8100 2 - 906 isdn compatibility b is the amount of time the system waits before placing the call in a talk state sufficient? In 21-01-03, enter the interval for the trunk interdigit timer. Should extension users have one-button placing of outside calls? Should extension users h...
Page 939
Univerge sv8100 issue 11.0 ivr – appointment reminder server 2 - 907 ivr – appointment reminder server description the ivr – appointment reminder server solution is designed to provide a knowledge-based, intelligent distributed application to optimize the scheduling and reminder of appointments. The...
Page 940
Issue 11.0 univerge sv8100 2 - 908 ivr – appointment reminder server appointment reminder call flow out bound call - new call if the call is answered: play main greeting hello this is an appointment reminder from (name of customer). (text to speech name) your appointment is scheduled for (time and d...
Page 941
Univerge sv8100 issue 11.0 ivr – appointment reminder server 2 - 909 if the sv8100 is configured for forced account codes, the account code must be entered before the dialed number in the ivr – appointment reminder server. For example: if the system account code is "123456" and the appointment remin...
Page 942
Issue 11.0 univerge sv8100 2 - 910 ivr – appointment reminder server guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizar...
Page 943
Univerge sv8100 issue 11.0 ivr – appointment reminder server 2 - 911 10-12-10 cd-cp00-us network setup – subnet mask set the subnet mask of the ipla/iplb. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.2...
Page 944
Issue 11.0 univerge sv8100 2 - 912 ivr – appointment reminder server 11-02-01 extension numbering set the extension number for the appointment reminder ports. The extension numbers must be assigned to unused hardware ports to allow the appointment reminder sip stations to register. Up to eight digit...
Page 945
Univerge sv8100 issue 11.0 ivr – appointment reminder server 2 - 913 16-01-04 department group basic data setup – hunting mode this program sets what happens when an unanswered call to a department group pilot number reaches the last member of the group. If set to (0), once the last extension is cal...
Page 946
Issue 11.0 univerge sv8100 2 - 914 ivr – appointment reminder server operation for operating procedures refer to the ivr – appointment reminder server configuration guide. 84-26-01 ipl basic setup – ip address assign the ip address for each dsp on the ipla/iplb. Xxx.Xxx.Xxx.Xxx defaults: slot 1 = 17...
Page 947: Ivr – Broadcast Server
Univerge sv8100 issue 11.0 ivr – broadcast server 2 - 915 ivr – broadcast server description the ivr – broadcast server solution is designed to provide a knowledge based, intelligent distributed application which provides the most cost effective form of contacting your customers, employees, and pros...
Page 948
Issue 11.0 univerge sv8100 2 - 916 ivr – broadcast server hello this is a broadcast message from (name of customer). Customers personal message played here. To replay this message press 1. If the customer presses 1 the message will repeat. If the customer presses anything other than the digit 1, the...
Page 949
Univerge sv8100 issue 11.0 ivr – broadcast server 2 - 917 system availability terminals all terminals required component(s) cd-cp00-us pz-32ipla/iplb, pz-64ipla/iplb, pz-128ipla/iplb lk-sys-ip-terminal-sip1-lic (one license required per broadcast port. For 16 ports of broadcast (16) lk-sys-ip-termin...
Page 950
Issue 11.0 univerge sv8100 2 - 918 ivr – broadcast server guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feat...
Page 951
Univerge sv8100 issue 11.0 ivr – broadcast server 2 - 919 10-12-10 cd-cp00-us network setup – subnet mask set the subnet mask of the ipla/iplb. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 255....
Page 952
Issue 11.0 univerge sv8100 2 - 920 ivr – broadcast server 11-02-01 extension numbering set the extension number for the ivr – broadcast ports. The extension numbers must be assigned to unused hardware ports to allow the ivr – broadcast sip stations to register. Up to eight digits 1 101 2 102 3 103 ~...
Page 953
Univerge sv8100 issue 11.0 ivr – broadcast server 2 - 921 16-01-04 department group basic data setup – hunting mode this program sets what happens when an unanswered call to a department group pilot number reaches the last member of the group. If set to (0), once the last extension is called the hun...
Page 954
Issue 11.0 univerge sv8100 2 - 922 ivr – broadcast server operation for operating procedures refer to the sv8100 ivr – broadcast server configuration guide. 84-26-01 ipl basic setup – ip address assign the ip address for each dsp on the ipla/iplb. Xxx.Xxx.Xxx.Xxx defaults: slot 1 = 172.16.0.20 : slo...
Page 955: K-Ccis – Ip
K-ccis – ip 2 - 923 k k-ccis – ip description the system uses the pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb daughter board to connect multiple systems together over a data communication ip network (intranet). Key-common channel interoffice signaling (kccis) is used to provide telephony servi...
Page 956
Issue 11.0 univerge sv8100 2 - 924 k-ccis – ip the univerge sv8100 uses the nec proprietary ccis peer to peer protocol over ip to communicate between system to system. The pz-(x)ipla/iplb is required for connections between ip terminals and ip trunks. Only one pz-(x)ipla/iplb daughter board can be a...
Page 957
Univerge sv8100 issue 11.0 k-ccis – ip 2 - 925 only one pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb daughter board can be installed on the cd-cp00-us. The pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb daughter board has layer2 switch ability, along with a gigabit ethernet lan interface and...
Page 958
Issue 11.0 univerge sv8100 2 - 926 k-ccis – ip ccis call back can only be set when the destination party is busy, and the calling party hears a busy tone. The calling party must hang up after setting ccis call back. Ccis call back can only be set by pressing a programmed feature key. Softkeys or dia...
Page 959
Univerge sv8100 issue 11.0 k-ccis – ip 2 - 927 in a ccis network, the memo display function only supports did calls directed across ccis to a remote system. Calls forwarded or transferred across ccis do not support the memo display function. With sv8100 version 5000 (5.00 or higher) software and pz-...
Page 960
Issue 11.0 univerge sv8100 2 - 928 k-ccis – ip conditions main software version 4000 (4.01 or higher) and the version 4000 main version license is required for the sv8100 to support peer to peer in a ccisoip network. Dt700 terminals are supported for peer to peer connections via a p2p ccis call. Sta...
Page 961
Univerge sv8100 issue 11.0 k-ccis – ip 2 - 929 default setting enabled system availability terminals none required component(s) cd-cp00-us with pz-32/64/128ipla or pz-32/64/128iplb daughter board related features k-ccis – ip guide to feature programming the level 1, level 2 and level 3 columns indic...
Page 962
Issue 11.0 univerge sv8100 2 - 930 k-ccis – ip k-ccisoip fax: 50-15-04 ccis over ip basic information setting – connection method for terminal choose the connection method for the dt700. 0 = peer to peer disable 1 = peer to peer enable (default = 1) 84-21-21 ccis over ip codec information basic setu...
Page 963
Univerge sv8100 issue 11.0 k-ccis – ip 2 - 931 ccis call back: 84-32-05 fax over ip codec setup – average jitter buffer setup fax over ip codec settings when using ccis over ip. 0~300 (default = 40) 84-32-06 fax over ip codec setup – maximum jitter buffer setup fax over ip codec settings when using ...
Page 964
Issue 11.0 univerge sv8100 2 - 932 k-ccis – ip operation refer to the univerge sv8100 networking manual for detailed feature information. 20-13-06 class of service options (supplementary service) – automatic off-hook signaling (automatic override) allow a busy extension to automatically (1) or manua...
Page 965: K-Ccis – Ip With Pva
Univerge sv8100 issue 11.0 k-ccis – ip with pva 2 - 933 k-ccis – ip with pva description the k-ccis – ip with pva feature provides the benefits and additional feature compatibility of key-common channel interoffice signaling (k-ccis) between multiple systems including neax pbx systems connected toge...
Page 966
Issue 11.0 univerge sv8100 2 - 934 k-ccis – ip with pva centralized e911 dial access to attendant direct inward dialing dual hold elapsed time display flexible numbering of stations hands-free answerback hot line link reconnect multiple call forwarding – all calls multiple call forwarding – busy/no ...
Page 967
Univerge sv8100 issue 11.0 k-ccis – ip with pva 2 - 935 one cd-pvaa is required to support up to 24 channels of k-ccis – ip with pva. Up to eight cd-pvaa blades can be installed in the univerge sv8100. Port assignment of the cd-pvaa package depends on the k-ccis – ip with pva license. You must input...
Page 968
Issue 11.0 univerge sv8100 2 - 936 k-ccis – ip with pva this features requires version 3000 (3.01 or higher) cpu software and version 3000 enhancement license (0031). The k-ccis – ip with pva shares the co/pbx/tie/did trunks available for the system. The cd-pvaa blade supports only those codecs that...
Page 969
Univerge sv8100 issue 11.0 k-ccis – ip with pva 2 - 937 if any network where the cd-pvaa blade is connected uses nat for connecting the voice calls (including firewall), consulting your network provider/administrator and specifically requesting service for voip or real-time media support on your net...
Page 970
Issue 11.0 univerge sv8100 2 - 938 k-ccis – ip with pva packet loss must not exceed 1%. Data switches must be manageable. Routers must provide qos. Adequate bandwidth for estimated voip traffic. Centralized voice mail is supported from the univerge sv8100 or electra elite ipk ii when using 5-, 6-, 7...
Page 971
Univerge sv8100 issue 11.0 k-ccis – ip with pva 2 - 939 when the k-ccis – ip with pva application is installed in the univerge sv8100, the system assigns the first available logical port numbers for ccisoip trunks. When using k-ccis – t1 or k-ccis – ip with pva in a netlink system, the ccta or pva-c...
Page 972
Issue 11.0 univerge sv8100 2 - 940 k-ccis – ip with pva direct access of k-ccis – ip with pva voice or data channels using line keys or specified line seizure access codes is prohibited. The recall key or drop key does not function on k-ccis – ip with pva calls. When either key is pressed, operation...
Page 973
Univerge sv8100 issue 11.0 k-ccis – ip with pva 2 - 941 the ccisoip fax enhancement feature is not supported when using k-ccis – ip with pva. The ccis call back feature is not supported when using k-ccis – ip with pva. Default setting none system availability terminals all terminals required compone...
Page 974
Issue 11.0 univerge sv8100 2 - 942 k-ccis – ip with pva related features k-ccis – ip guide to feature programming none operation normal call handling procedures apply. Refer to the univerge sv8100 networking manual for detailed feature information..
Page 975: K-Ccis – T1
Univerge sv8100 issue 11.0 k-ccis – t1 2 - 943 k-ccis – t1 description key-common channel interoffice signaling (k-ccis) allows multiple systems to be connected to provide additional feature compatibility, above what normal tie lines provide. The system is configured with a 24 channel t1 connection ...
Page 976
Issue 11.0 univerge sv8100 2 - 944 k-ccis – t1 direct inward dialing – k-ccis dual hold – k-ccis elapsed time display – k-ccis flexible numbering of stations – k-ccis hands-free answerback – k-ccis hot line – k-ccis ip (k-ccis) ip (k-ccis) to neax (point-to-multipoint) link reconnect – k-ccis multip...
Page 977
Univerge sv8100 issue 11.0 k-ccis – t1 2 - 945 outgoing co calls in a k-ccis network can be routed over the k-ccis link and use the distant system co lines. Distant system extension numbers in the k-ccis network can be assigned to feature access or one touch keys and speed dial buffers. When a k-cci...
Page 978
Issue 11.0 univerge sv8100 2 - 946 k-ccis – t1 centralized e911 – k-ccis is supported. When centralized e911 – k-ccis is not used, each univerge sv8100 system in a k-ccis network must have at least one trunk for emergency 911 calls. Using a neax-to-univerge sv8100 network, the pbx must supply centra...
Page 979
Univerge sv8100 issue 11.0 k-ccis – t1 2 - 947 when connecting a sv8100 to a neax pbx, link reconnect needs to be turned off in the pbx to the sv8100. The ccis call back feature requires version 5000 or higher software and the version 5000 enhancement license. Call forward busy no answer must be dis...
Page 980
Issue 11.0 univerge sv8100 2 - 948 k-ccis – t1 the called extension has ability to receive callback settings from multiple extensions. If this occurs the callback requests are returned in the order received. The ccis callback feature does not apply to trunk calls as it does not include trunk queuing...
Page 981
Univerge sv8100 issue 11.0 k-ccis – t1 2 - 949 related features t1 trunking (with ani/dnis compatibility) universal slots guide to feature programming refer to the univerge sv8100 key-common channel interoffice signaling (k-ccis) manual. Operation refer to the univerge sv8100 key-common channel inte...
Page 982
Issue 11.0 univerge sv8100 2 - 950 k-ccis – t1 this page intentionally left blank.
Page 983: Last Number Redial
Last number redial 2 - 951 l last number redial description last number redial allows an extension user to quickly redial the last number dialed. For example, a user may quickly recall a busy or unanswered number without manually dialing the digits. Last number redial saves in system memory the last...
Page 984
Issue 11.0 univerge sv8100 2 - 952 last number redial conditions redial list requires the use of a display telephone. Non-display and single line telephones cannot use this feature. When using automatic route selection, ars selects the trunk for the call unless the user preselects. Default setting e...
Page 985
Univerge sv8100 issue 11.0 last number redial 2 - 953 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature ...
Page 986
Issue 11.0 univerge sv8100 2 - 954 last number redial 2. To redial the last number, press # . - or - search for the desired number from the redial list by pressing redial or volume or volume keys. - or - press the left cursor key once and the volume or volume keys to find number. 3. Lift the h...
Page 987: Licensing
Univerge sv8100 issue 11.0 licensing 2 - 955 licensing enhancements the napt feature requires a version 3000 or higher system license in order to be activated. A cd-cp00-us (cpu) can be upgrade to a version 3000 or higher system software however, the napt feature will not function unless a version 3...
Page 988
Issue 11.0 univerge sv8100 2 - 956 licensing description licenses are used to activate certain features and applications for the univerge sv8100. The univerge sv8100 system provides the following licenses: system licenses: system capacity max port – this licenses the system for up to 712 ports. (req...
Page 989
Univerge sv8100 issue 11.0 licensing 2 - 957 ip trunks – this licenses the number of sip trunks that can be installed in the system. Ip terminal basic – this licenses the number of dt700 phones that can be connected to the system. Ip terminal basic – this licenses the number of third party sip phone...
Page 990
Issue 11.0 univerge sv8100 2 - 958 licensing ums amis/plus net – this licenses the ums for amis/plus net. Ums tts channel – this licenses the number of tts channels that can be used in the ums. Ums tts language – this licenses the number of languages that can be used simultaneously for tts. Ums lite...
Page 991
Univerge sv8100 issue 11.0 licensing 2 - 959 acd mis acd mis basic – this licenses the sv8100 acd mis. Acd mis add monitor – this licenses the sv8100 acd mis for monitor/report. Acd mis agent – this licenses the sv8100 acd mis for agent client. Pva pva-conference channel – this licenses the number o...
Page 992
Issue 11.0 univerge sv8100 2 - 960 licensing recovery license the recovery license turns on all licenses for up to 30 days. To request a recovery license, go to http://eip.Necunified.Com/default.Aspx and then go to the license portal and select the customer and the location of the cd-cp00-us. This c...
Page 993
Univerge sv8100 issue 11.0 licensing 2 - 961 when the number of days for the temporary license is assigned, system reset is required for the license to take affect. When the number of the date is 0 (disable), the number can be set (1~10). When the number of the date is 1~10, the date can be set to 0...
Page 994
Issue 11.0 univerge sv8100 2 - 962 licensing related features programming from multiline terminal guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are use...
Page 995
Univerge sv8100 issue 11.0 licensing 2 - 963 90-37-01 set temporary license – set number of days for temporary license use to set the effective days of the temporary license requires system reset to take affect). 00~10 days 0 = temporary license is invalid (default = 0) 90-55-01 free license select ...
Page 996
Issue 11.0 univerge sv8100 2 - 964 licensing 0044 sphericall – on/off – 0045 microsoft ocs 2007/cs2010 – on/off – 0111 1stpartycti ether – 1 128 – 0112 3rdpartycti clien yes on/off – 0123 soai interface – on/off – 0141 dtplusware user – 1 64 – 1001 vrs – 1 16 – 1002 inmail – 1 8 – 1011 inmail multi ...
Page 997
Univerge sv8100 issue 11.0 licensing 2 - 965 1425 ums lite ch – 1 8 ums port license. The lite license does not support text- to-speech, networking and will support up to two ports for fax. 1426 ums lite 2up – on/off 2-port lite upgrade kit. 1427 ums lite full – on/off upgrade from ums lite to full ...
Page 998
Issue 11.0 univerge sv8100 2 - 966 licensing 3010 ca-ipkii cesmigra – on/off – 3013 ca-add stations – 1 256 – 3014 ca-e911 reporting – 1 999 – 3200 ip recorder basic – on/off – 3201 rec basic supv – 1 256 – 3202 rec basic port – 1 256 – 3300 esn registry – on/off – 3301 esn site monitor – 1 999 – 33...
Page 999
Univerge sv8100 issue 11.0 licensing 2 - 967 operation there are four different ways to activate the licenses in the system: manual enter software key code: 1. In program 10-48-01 enter the software key code. 2. In program 10-48-02 enter the activation code. 3. In program 10-48-03 enter the feature ...
Page 1000
Issue 11.0 univerge sv8100 2 - 968 licensing auto register the license for the system: 1. Connect to the system. 2. Go to the feature activation screen. 3. Enter email address and password. 4. Add software key code(s). If left blank, it registers all attached licenses for the hardware key code. 5. C...
Page 1001: Line Preference
Univerge sv8100 issue 11.0 line preference 2 - 969 line preference description line preference determines how a multiline terminal user places and answers calls. Line preference has two types: incoming line preference or outgoing line preference. Incoming line preference incoming line preference est...
Page 1002
Issue 11.0 univerge sv8100 2 - 970 line preference default setting enabled system availability terminals all multiline terminals required component(s) none related features direct inward line (dil) ring groups trunk groups.
Page 1003
Univerge sv8100 issue 11.0 line preference 2 - 971 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pro...
Page 1004
Issue 11.0 univerge sv8100 2 - 972 line preference 14-07-01 trunk access map setup for outgoing line preference and auto-answer of non-ringing lines, set up the trunk access maps. 0 = no access 1 = outgoing access only 2 = incoming access only 3 = access only when trunk on hold 4 = outgoing access a...
Page 1005
Univerge sv8100 issue 11.0 line preference 2 - 973 operation ringing trunk or intercom (icm) call: lift the handset or press speaker. The setting assigned for program 15-02-10 and program 22-01-01 determines which call is answered first. 22-04-01 incoming extension ring group assignment assign exten...
Page 1006
Issue 11.0 univerge sv8100 2 - 974 line preference this page intentionally left blank.
Page 1007: Long Conversation Cutoff
Univerge sv8100 issue 11.0 long conversation cutoff 2 - 975 long conversation cutoff description for incoming and outgoing central office calls, each trunk can be programmed to disconnect after a defined time. The timer begins when the trunk is seized and disconnects the call after the time expires....
Page 1008
Issue 11.0 univerge sv8100 2 - 976 long conversation cutoff related features central office calls, answering central office calls, placing direct inward system access (disa) multiple trunk types warning tone for long conversation guide to feature programming the level 1, level 2 and level 3 columns ...
Page 1009
Univerge sv8100 issue 11.0 long conversation cutoff 2 - 977 operation this feature is automatic once it is programmed. 20-13-02 class of service options (supplementary service) – long conversation cutoff (incoming) turn off or on an extension user ability to use long conversation cutoff for incoming...
Page 1010
Issue 11.0 univerge sv8100 2 - 978 long conversation cutoff this page intentionally left blank.
Page 1011: Loop Keys
Univerge sv8100 issue 11.0 loop keys 2 - 979 loop keys description loop keys are uniquely programmed function keys that simplify placing and answering trunk calls. There are three types of loop keys: incoming only, outgoing only and both ways. Incoming only loop keys incoming only loop keys are for ...
Page 1012
Issue 11.0 univerge sv8100 2 - 980 loop keys conditions with version 4000 or higher software, loop keys can only be assigned or used when program 20-02-03 is set to ux5000 (1). A system can use either cap keys or loops keys. When sv telephones are installed, cap key mode must be used. When ux teleph...
Page 1013
Univerge sv8100 issue 11.0 loop keys 2 - 981 ring groups tie lines guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards...
Page 1014
Issue 11.0 univerge sv8100 2 - 982 loop keys 14-07-01 trunk access map setup for outgoing line preference and auto-answer of non-ringing lines, set up the trunk access maps. 0 = no access 1 = outgoing access only 2 = incoming access only 3 = access only when trunk on hold 4 = outgoing access and acc...
Page 1015
Univerge sv8100 issue 11.0 loop keys 2 - 983 20-02-23 system options for multiline telephones – ux5000 phone operation mode selects the loop key operation like the ux5000 terminal, or the cap key operation like the sv8100 terminal. 0 = original operation mode (cap key) 1 = ux5000 special operation m...
Page 1016
Issue 11.0 univerge sv8100 2 - 984 loop keys operation to place a call on a loop key: 1. Press outgoing or both ways loop key. You hear dial tone and the key lights green. 2. Dial number. To answer a call on a loop key: listen for ringing or look for a flashing loop key. 1. Press loop key. The key l...
Page 1017: Maintenance
Maintenance 2 - 985 m maintenance description the univerge sv8100 system has several utilities to assist in troubleshooting and diagnosing problems both during and after installation. Pcpro can remotely access the univerge sv8100 for maintenance and diagnostics. Within pcpro, the debug terminal can ...
Page 1018
Issue 11.0 univerge sv8100 2 - 986 maintenance after successful measurement, the option to copy the same settings to all analog trunks is shown. Side tone auto setup available when the system is in an idle condition. Conditions none default setting enabled system availability terminals none required...
Page 1019: Meet Me Conference
Univerge sv8100 issue 11.0 meet me conference 2 - 987 meet me conference description with meet me conference, an extension user can set up a conference with their current call and up to 31 other internal or external parties. Each party joins the conference by dialing a meet me conference code. Meet ...
Page 1020
Issue 11.0 univerge sv8100 2 - 988 meet me conference guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature ...
Page 1021
Univerge sv8100 issue 11.0 meet me conference 2 - 989 operation meet me external conference: to make a meet me external conference: multiline terminal 1. While on a call, press conf softkey. 2. Dial 1 and the combined paging zone code 1~8 (for internal/external zones 1~8) or 0 (for internal/external...
Page 1022
Issue 11.0 univerge sv8100 2 - 990 meet me conference meet me internal conference: to make a meet me internal conference: multiline terminal 1. While on a call, press conf softkey. 2. Dial 1 and the combined paging zone code 1~8 (for internal/external zones 1~8) or 0 (for internal/external all call)...
Page 1023: Meet Me Paging
Univerge sv8100 issue 11.0 meet me paging 2 - 991 meet me paging description meet me paging allows an extension user to page a co-worker and privately meet with them on a page zone. The paging zone is busy to other users while the meeting takes place. While the co-workers meet on the zone, no one el...
Page 1024
Issue 11.0 univerge sv8100 2 - 992 meet me paging meet me paging transfer paging, external paging, internal programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are mos...
Page 1025
Univerge sv8100 issue 11.0 meet me paging 2 - 993 for additional programming information on paging, refer to the paging, external and paging, internal features. Operation meet me external page: to make a meet me external page: 1. At multiline terminal, press speaker or pick up the handset. - or - at...
Page 1026
Issue 11.0 univerge sv8100 2 - 994 meet me paging 2. Dial 703 and the external paging zone code (1~8 or 0 for all call). - or - dial 1 and the combined paging zone code 1~8 (for internal/external zones 1~8) or 0 (for internal/external all call). 3. Announce the zone. - or - 1. At the multiline termi...
Page 1027
Univerge sv8100 issue 11.0 meet me paging 2 - 995 to join a meet me internal page: 1. At the multiline terminal, press speaker or pick up the handset. - or - at the single line telephone, lift the handset. 2. Dial 763 (if your extension is in the zone called). - or - dial 764 and the zone number (if...
Page 1028
Issue 11.0 univerge sv8100 2 - 996 meet me paging this page intentionally left blank.
Page 1029: Meet Me Paging Transfer
Univerge sv8100 issue 11.0 meet me paging transfer 2 - 997 meet me paging transfer description if a user wants to transfer a call to a co-worker but they do not know where the co-worker is, they can use meet me paging transfer. With meet me paging transfer, the user can page the co-worker and have t...
Page 1030
Issue 11.0 univerge sv8100 2 - 998 meet me paging transfer related features meet me conference meet me paging paging, external paging, internal programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming th...
Page 1031
Univerge sv8100 issue 11.0 meet me paging transfer 2 - 999 11-12-21 service code setup (for service access) – meet-me answer to specified internal paging group customize the service codes used for meet-me answer to specified internal paging group service access. Mlt, slt (default = 764) 11-12-22 ser...
Page 1032
Issue 11.0 univerge sv8100 2 - 1000 meet me paging transfer for additional programming information on paging, refer to the paging, external and paging, internal features. Operation meet me external paging transfer: to make a meet me external paging transfer: 1. At the multiline terminal, while on a ...
Page 1033
Univerge sv8100 issue 11.0 meet me paging transfer 2 - 1001 3. Dial the announced external paging zone (0~8). The paging party is connected. 4. Stay on the line. From a multiline terminal, press transfer or the transfer softkey. - or - from a single line telephone, hang up. The party is transferred....
Page 1034
Issue 11.0 univerge sv8100 2 - 1002 meet me paging transfer 2. Dial 763 (if your extension is in the zone called). - or - dial 764 and the zone number (if your extension is not in the zone called). - or - press the meet me conference/paging pickup key (program 15-07 or sc 751: 23) if your extension ...
Page 1035: Memo Dial
Univerge sv8100 issue 11.0 memo dial 2 - 1003 memo dial description on an outside call, memo dial lets a multiline terminal user store an important number for easy redialing later on. The telephone can be like a notepad. For example, a user could dial directory assistance and ask for a client’s tele...
Page 1036
Issue 11.0 univerge sv8100 2 - 1004 memo dial related features central office calls, placing last number redial save number dialed guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most co...
Page 1037
Univerge sv8100 issue 11.0 memo dial 2 - 1005 to call a stored memo dial number: 1. Do not lift the handset. 2. Press the memo dial key (program 15-07 or sc 751: 31). 3. Press speaker. The stored number dials out only if you store a trunk access code before the number. - or - press the line key. The...
Page 1038
Issue 11.0 univerge sv8100 2 - 1006 memo dial this page intentionally left blank.
Page 1039: Message Waiting
Univerge sv8100 issue 11.0 message waiting 2 - 1007 message waiting description an extension user can leave a message waiting indication at a busy or unanswered extension requesting a return call. The indication is a flashing mw lamp at the called extension and a steadily lit mw lamp on the calling ...
Page 1040
Issue 11.0 univerge sv8100 2 - 1008 message waiting conditions reminder messages require a dsp daughter board for vrs messages. Analog ports from apa or apr adapters do not provide message waiting lamping. When a user responds to a message waiting, the system does not cancel the message waiting indi...
Page 1041
Univerge sv8100 issue 11.0 message waiting 2 - 1009 required component(s) none related features handsfree answerback/forced intercom ringing hotel/motel programmable function keys um8000 mail vm8000 inmail voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 colu...
Page 1042
Issue 11.0 univerge sv8100 2 - 1010 message waiting 11-11-11 service code setup (for setup/ entry operation) – cancel message waiting cancel message waiting used for registration and setup. Mlt, slt (default = 771) 11-16-07 single digit service code setup – message waiting customize the message wait...
Page 1043
Univerge sv8100 issue 11.0 message waiting 2 - 1011 operation to leave a message waiting: 1. Call busy or unanswered extension. 2. Dial 0 or press the message waiting key (program 15-07 or sc 751: 38). 3. Hang up. With multiline terminal telephones, the message waiting led lights. 20-06-01 class of ...
Page 1044
Issue 11.0 univerge sv8100 2 - 1012 message waiting to answer a message waiting: when you have a message, your message waiting led flashes fast for multiline terminals. 1. At the multiline terminal, press speaker and dial 0. - or - press the message waiting key (program 15-07 or sc 751: 38). - or - ...
Page 1045
Univerge sv8100 issue 11.0 message waiting 2 - 1013 to check your messages: 1. Press message key or the mw (message waiting) softkey. 2. Dial 0. You can have any combination of the message types in the table below on your telephone. 3. Press vol or vol to scroll through your display. 4. When you...
Page 1046
Issue 11.0 univerge sv8100 2 - 1014 message waiting this page intentionally left blank.
Page 1047: Mh240 Wireless Ip Telephone
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1015 mh240 wireless ip telephone description the mh240 wireless ip telephone is a wireless ip multiline terminal. The wl1700 controller is the equipment that controls additional wl1500 access points (aps) and has it’s own internal ap. The wl...
Page 1048
Issue 11.0 univerge sv8100 2 - 1016 mh240 wireless ip telephone call admission control (cac) the combination of wl1700 and mh240 provides call admission control, which regulates addition of new voip sessions on ap radios. Cac can be used to ensure voip sessions by limiting the number of active voice...
Page 1049
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1017 coverage the required number and placement of aps in a given environment is driven by several factors, including the intended coverage area, system capacity, power output, physical environment, and radio mode. Many enterprise wi-fi netw...
Page 1050
Issue 11.0 univerge sv8100 2 - 1018 mh240 wireless ip telephone key confirmation tone is provided by the mh240 and not by the sv8100 system programming. The backlight led duration is provided by the mh240 and not by the sv8100 system programming. Call history is stored on the mh240, not in the sv810...
Page 1051
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1019 program 10-46-01 must be set to 1 (auto) or 2 (manual) for multiple logon to work. When three ports are assigned the same personal id index in program 15-05-27, if program 15-05-26 is not set for those ports, the terminal types will be ...
Page 1052
Issue 11.0 univerge sv8100 2 - 1020 mh240 wireless ip telephone battery backup – system memory n/a battery backup – system power n/a call appearance (cap) keys x call arrival (car) keys x call duration timer x call forwarding x call forwarding – centrex x call forwarding with follow me x call forwar...
Page 1053
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1021 code restriction, dial block x conference x conference, voice call/privacy release x continued dialing x cordless dect terminals n/a cordless telephone connection n/a data line security x delayed ringing x department calling x departmen...
Page 1054
Issue 11.0 univerge sv8100 2 - 1022 mh240 wireless ip telephone distinctive ringing, tones and flash patterns x mh240 has a local ring pattern setting. Mh240 cannot change the ring pattern by service code 11-11-20~11-11-21 and 15-02-02~15-02-03. Do not disturb x mh240 does not have soft keys so it h...
Page 1055
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1023 headset operation x headset key is not supported on first release. Also, command 15-02-41does not affect mh240 there is a local setting for this. Also, when the headset is plugged in you have to use the headset you can not use the hands...
Page 1056
Issue 11.0 univerge sv8100 2 - 1024 mh240 wireless ip telephone last number redial x to get lnr to work properly set the following commands accordingly: 15-02-13:0 15-05-28:1 licensing x line preference x long conversation cutoff x maintenance x meet me conference x meet me paging x meet me paging t...
Page 1057
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1025 park x pbx compatibility x pc programming x power failure transfer n/a prime line selection x private line x programmable function keys x programming from a multiline terminal x pulse to tone conversion x redial function x remote (syste...
Page 1058
Issue 11.0 univerge sv8100 2 - 1026 mh240 wireless ip telephone single line telephones, analog 500/2500 sets n/a slt adapter x smb8000 communications analyst x smb8000 interactive voice response x smb8000 conference bridge x softkeys x speed dial – system/group/station x station hunt x station messa...
Page 1059
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1027 traffic reports x transfer x on a transferred call ring tone may skip once. Internal ring tone and transfer ring tone are the same on the mh240. So when it changes from the internal to transfer there can be what sounds like a skip in th...
Page 1060
Issue 11.0 univerge sv8100 2 - 1028 mh240 wireless ip telephone refer to the following tables for a listing of the function codes supported by the mh240. Table 2-60 program 15-07 function codes (service code 751) function number function name supported not supported 00 not defined x 01 dss/one-touch...
Page 1061
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1029 29 repeat redial x 30 saved number redial x 31 memo dial x 32 meet – me conference x 33 override (off-hook signaling) x 34 break – in x 35 camp on x 36 step call x 37 dnd/fwd override call x 38 message waiting x 39 room monitoring x 40 ...
Page 1062
Issue 11.0 univerge sv8100 2 - 1030 mh240 wireless ip telephone 57 general purpose led indication x 58 automatic transfer at department group call x 59 delayed transfer at department group call x 60 dnd at department group call x 61 --- not used --- 63 outgoing call without caller id (isdn) x 64 ---...
Page 1063
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1031 88 dial-in mode switching x 89 do-not-call setup x 90 do-not-call data registration x 91 live recording key inmail x 94 call attendant x 97 door box access key x 98 --- not used --- 99 --- not used --- table 2-61 program 15-07 function ...
Page 1064
Issue 11.0 univerge sv8100 2 - 1032 mh240 wireless ip telephone refer to the following tables for the service code setup listing supported by the mh240. 18 acd overflow control x 19 acd queue status display check x table 2-62 program 11-10 service code setup (setup/entry operation) function number f...
Page 1065
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1033 21 vrs - general message playback x 22 vrs - record or erase general message x 23 smdr - extension accumulated printout code x 24 smdr - group accumulated printout code x 25 account code accumulated printout code x 26 forced trunk disco...
Page 1066
Issue 11.0 univerge sv8100 2 - 1034 mh240 wireless ip telephone 07 call forwarding – follow-me x 08 do not disturb x 09 answer message waiting x 10 cancel all messages waiting x 11 cancel message waiting x 12 alarm clock x 13 display language selection for multiline terminal x 14 text message settin...
Page 1067
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1035 32 --- not used --- 33 dial block x 34 temporary toll restriction override x 35 pilot group withdrawing x 36 toll restriction override x 37 ring volume set x 38 programmable function key programming (3-digit service codes) x 39 station ...
Page 1068
Issue 11.0 univerge sv8100 2 - 1036 mh240 wireless ip telephone 57 set do not call table x 58 call forward with personal greeting x 59 call forward to attendant except busy x 60 call forward to attendant/no answer x 62 headset ring volume adjustment x 63 double height character indication x 64 rever...
Page 1069
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1037 17 clear last number dialing data x 18 clear saved number dialing data x 19 internal group paging x 20 external paging x 21 meet-me answer to specified internal paging group x 22 meet-me answer to external paging x 23 meet-me answer in ...
Page 1070
Issue 11.0 univerge sv8100 2 - 1038 mh240 wireless ip telephone 45 enabled on hook when holding (slt) x 46 answer on hook when holding (slt) x 47 call waiting answer/split answer x 48 account code x 49 --- not used --- 50 general purpose relay x 51 vms access (inmail and vms) x 52 live monitoring (i...
Page 1071
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1039 10 acd agent login by supervisor x 11 acd agent logout by supervisor x 12 change agent acd group by supervisor x 13 acd agent changing own acd group x table 2-66 program 11-14 service code setup (hotel) function number function name sup...
Page 1072
Issue 11.0 univerge sv8100 2 - 1040 mh240 wireless ip telephone ring tones the mh240 has three different ring tone settings; internal, external, and non-notification. Different types of incoming calls can ring differently depending on the setting in program 15-05-28. Table 2-67 program 11-15 service...
Page 1073
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1041 ring tones with program 15-05-28 enabled call type program 22-02-01 caller id ring pattern when call forward busy to the mh240 when call forward no answer to the mh240 analog trunk call 0: normal with caller id non-notification normal c...
Page 1074
Issue 11.0 univerge sv8100 2 - 1042 mh240 wireless ip telephone isdn trunk call 0: normal with caller id external ring normal call does not support busy transfer external ring without caller id non-notification normal call does not support busy transfer non-notification 1: vrs with caller id externa...
Page 1075
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1043 ring tones with program 15-05-28 disabled call type program 22-02-01 caller id ring pattern when call forward busy to the mh240 when call forward no answer to the mh240 analog trunk call 0: normal with caller id internal ring normal cal...
Page 1076
Issue 11.0 univerge sv8100 2 - 1044 mh240 wireless ip telephone default setting none isdn trunk call 0: normal with caller id internal ring normal call does not support busy transfer internal ring without caller id internal ring normal call does not support busy transfer internal ring 1: vrs with ca...
Page 1077
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1045 system availability terminals mh240 wireless ip terminals required component(s) cpu with pz-32ipla/iplb, pz-64ipla/iplb or pz-128ipla/iplb daughter board installed. Wl1700-ms wl1500-ms (optional) mh240 wireless ip handset related featur...
Page 1078
Issue 11.0 univerge sv8100 2 - 1046 mh240 wireless ip telephone guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards fo...
Page 1079
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1047 10-12-03 cd-cp00-us network setup – default gateway assign the default gateway ip address for the cd-cp00-us. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 191.254.255.254 192.0.0.1~ 223.255.255.254 (default = 0.0.0.0) 10-12-09 cd-cp00-us network...
Page 1080
Issue 11.0 univerge sv8100 2 - 1048 mh240 wireless ip telephone 84-10-01 tos setup – tos mode when input data is set to 1, protocol 7 is invalid. When data is set to 2, protocols 2~6 are invalid. 0 = disable (invalid) 1 = ip precedence 2 = diffserv (default = 0) 84-10-07 tos setup – priority (d.S.C....
Page 1081
Univerge sv8100 issue 11.0 mh240 wireless ip telephone 2 - 1049 in addition to the above programming, define the programming options as required for the system features. Refer to the univerge sv8100 programming manual and the univerge sv8100 networking manual for programming details. 84-22-04 dt700 ...
Page 1082
Issue 11.0 univerge sv8100 2 - 1050 mh240 wireless ip telephone operation to make a call: 1. Enter the telephone number and press the key -or- 2. Press the key and then enter the telephone number. To answer a call: 1. Press the key. 2. To stop the ring without answering the call, press the key. To p...
Page 1083: Microphone Cutoff
Univerge sv8100 issue 11.0 microphone cutoff 2 - 1051 microphone cutoff description microphone cutoff lets a multiline terminal user turn off their telephone handsfree or handset microphone anytime. When activated, microphone mute prevents the caller from hearing conversations in the user’s work are...
Page 1084
Issue 11.0 univerge sv8100 2 - 1052 microphone cutoff related features handsfree answerback/forced intercom ringing handset mute programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in t...
Page 1085
Univerge sv8100 issue 11.0 microphone cutoff 2 - 1053 operation to mute your telephone handset or handsfree microphone while on a call: 1. Press mic. This only turns off the handsfree microphone. - or - press the microphone cutoff key (program 15-07 or sc 751: 40). This turns off both the handset an...
Page 1086
Issue 11.0 univerge sv8100 2 - 1054 microphone cutoff this page intentionally left blank.
Page 1087: Mobile Extension
Univerge sv8100 issue 11.0 mobile extension 2 - 1055 mobile extension description a mobile extension is an external telephone (preferably a mobile phone) linked to the univerge sv8100 via a proxy port to operate as an internal single line telephone extension. The extension sends dtmf signals to the ...
Page 1088
Issue 11.0 univerge sv8100 2 - 1056 mobile extension this feature can currently be used with isdn pri trunks or sip trunks. It is recommended to use this feature with an isdn pcb (pri or bri), however, analog trunks can be used as well. To provide a proper disconnect, disconnect supervision is requi...
Page 1089
Univerge sv8100 issue 11.0 mobile extension 2 - 1057 department group member did toll restriction class of service dss keys though dss keys are available for the mobile extension, they cannot provide an exact indication of busy status if, for example, the mobile extension is active on a call not lin...
Page 1090
Issue 11.0 univerge sv8100 2 - 1058 mobile extension station speed dial number entry 11-11-39 755 yes auto attendant 11-11-44 no setting yes bypass call 11-12-01 707 yes yes conference 11-12-02 #1 yes override (off-hook signalling) 11-12-03 709 yes set camp-on 11-12-04 750 yes yes cancel camp-on 11-...
Page 1091
Univerge sv8100 issue 11.0 mobile extension 2 - 1059 park hold 11-12-31 #6 yes answer for park hold 11-12-32 *6 yes group hold 11-12-33 732 yes answer for group hold 11-12-34 762 yes personal (extension) park 11-12-35 757 yes door box access (door box can also ring the mobile extension, *# operates ...
Page 1092
Issue 11.0 univerge sv8100 2 - 1060 mobile extension although some features may be available to the mobile extension, it may be advisable to disable them in class of service. There are also features that should be disabled in any case. The features to be disabled/not used for mobile extension includ...
Page 1093
Univerge sv8100 issue 11.0 mobile extension 2 - 1061 caller id presented to the mobile extension for type of call direct internal call – cpn of the calling phone is presented to the mobile extension (version 3000 or higher software required). Direct trunk call with cid – caller id of incoming call i...
Page 1094
Issue 11.0 univerge sv8100 2 - 1062 mobile extension conditions it is recommended that this feature use isdn platform (as these trunks provide answer supervision). If an extension has call forward-both ring set to a mobile extension (twinning), it will not forward to vm or anywhere else (version 250...
Page 1095
Univerge sv8100 issue 11.0 mobile extension 2 - 1063 calls on mobile extension can be easily picked up from a telephone in the sv8100 system. This is done via a barge-in key (34+mobile ext# or 34+*) * will barge in to the extension that call forward both ring is set to. If no forward both ring is se...
Page 1096
Issue 11.0 univerge sv8100 2 - 1064 mobile extension in the callback to cell phone feature set program 15-22-04 to 1. If the cell phone user continues to ring over the time set in program 22-01-12, the system answers the call as a normal mobile extension call. Callback to cell phone will not proceed...
Page 1097
Univerge sv8100 issue 11.0 mobile extension 2 - 1065 required component(s) none related features speed dial – system/group/station caller id call forwarding direct inward dialing (did) direct inward line (dil) station message detail recording.
Page 1098
Issue 11.0 univerge sv8100 2 - 1066 mobile extension guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature p...
Page 1099
Univerge sv8100 issue 11.0 mobile extension 2 - 1067 13-04-01 speed dialing number and name – speed dialing data for the bin number defined in program 15-22-01 for the mobile extension, enter the external number of the mobile extension. This must exactly match the caller id number of the mobile exte...
Page 1100
Issue 11.0 univerge sv8100 2 - 1068 mobile extension 15-22-04 mobile extension setup – call back select whether or not the system will try to call back a mobile extension user. 0 = don’t call back 1 = call back (default = 0) 20-01-16 system options – mobile extension callback duration time determine...
Page 1101
Univerge sv8100 issue 11.0 mobile extension 2 - 1069 22-01-12 system options for incoming calls – mobile extension answer time determines the amount of time before the mobile extension will answer with internal dial tone. Extend this timer long enough for 1 ring cycle to complete, giving the mobile ...
Page 1102
Issue 11.0 univerge sv8100 2 - 1070 mobile extension 80-03-03 dtmf tone receiver setup – min. Detect level for the extension dtmf, the minimum detect level (0-15) for the dtmf tone must be set to allow a minimum detection level of -25dbm. This entry is dependent on the detect level selected in progr...
Page 1103
Univerge sv8100 issue 11.0 mobile extension 2 - 1071 callback to cell phone: program number program name description/comments assigned data level 1 2 3 13-04-01 speed dialing number and name – speed dialing data enter the common and group speed dialing numbers and names which are to be used for trun...
Page 1104
Issue 11.0 univerge sv8100 2 - 1072 mobile extension operation with any feature, if the mobile extension user presses *, an existing call is placed in hold. Pressing * a second time or the timeout of the inter-digit timer returns the call to conversation mode. Using analog lines with the mobile exte...
Page 1105
Univerge sv8100 issue 11.0 mobile extension 2 - 1073 program 15-22-02 set to 0 or 1 (dtmf confirmation required): the caller is retrieved by the univerge sv8100 and follows the no-answer programming (ring another extensions, forward to univerge sv8100 voice mail, etc.) program 15-22-02 set to 2 (no ...
Page 1106
Issue 11.0 univerge sv8100 2 - 1074 mobile extension swapping between two held calls from the mobile extension 1. While on a call, press * #. The first call is placed on hold. 2. Place second call, then place on hold by pressing * #. The second call is placed on hold and the first call is picked up....
Page 1107
Univerge sv8100 issue 11.0 mobile extension 2 - 1075 to activate call forward follow me: 1. When activating call forwarding from the mobile extension: dial the did or dil telephone number for the mobile extension. If the caller id of the mobile extension matches the speed dial bin entry (program 13-...
Page 1108
Issue 11.0 univerge sv8100 2 - 1076 mobile extension receive callback: receive call from mobile extension and callback: cell phone number: 09012345678 incoming trunk set up: 22-02: trk1, dil mobile extension set up: ext150 program 15-22-01: speed dial bin no, 50 program 15-22-03: trunk access code, ...
Page 1109
Univerge sv8100 issue 11.0 mobile extension 2 - 1077 after callback answered, but does not send any dtmf: 1. Call the system trk1 from the cell phone setting as a mobile extension (ex 150). 2. The cell phone user hangs up within 3 seconds, before system answers. 3. System makes the callback to the c...
Page 1110
Issue 11.0 univerge sv8100 2 - 1078 mobile extension this page intentionally left blank.
Page 1111: Multiple Trunk Types
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1079 multiple trunk types description the univerge sv8100 supports many different trunks in the system (did, e&m tie lines, loop start, ground start, isdn bri, isdn pri, and t-1 trunks). The system supports up to 200 trunks in the expanded port pac...
Page 1112
Issue 11.0 univerge sv8100 2 - 1080 multiple trunk types when adding or removing padding for trunks, use program 14-01 for all trunks except the pri trunks in a migration cabinet. Use program 81-12 to add or remove padding for pri trunks in a migration cabinet. Default setting none system availabili...
Page 1113
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1081 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featu...
Page 1114
Issue 11.0 univerge sv8100 2 - 1082 multiple trunk types 14-05-01 trunk group – trunk group number assign trunks to trunk groups. You can also assign the outbound priority for trunks in the group. When users dial the trunk group, they seize the trunks in the order you specify in the outbound priorit...
Page 1115
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1083 tie lines: 81-10-05 cot initial data setup – auto release signal detection time specify the signal detection time for release of a co/pbx line after a disconnect signal is received from the distant central office or pbx. 1~14 (50~700ms) 15 = (...
Page 1116
Issue 11.0 univerge sv8100 2 - 1084 multiple trunk types 14-05-01 trunk group – trunk group number program tie lines of similar type into the same trunk group. The system uses trunk groups for outgoing access to tie lines (i.E., service code 704 + group). Also see program 34-05-01. Trunk group numbe...
Page 1117
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1085 20-14-01 class of service options for disa/e&m – first digit absorption (delete first digit dialed) for tie lines, turn off or on the ability to absorb (ignore) the first incoming digit. Use this to make the tie trunk compatible with 3- and 4-...
Page 1118
Issue 11.0 univerge sv8100 2 - 1086 multiple trunk types 20-14-11 class of service options for disa/e&m – disa/tie trunk barge-in turn off or on a disa or tie trunk caller ability to use barge-in. 0 = off 1 = on (default = 0 for cos 1~15) 20-14-12 class of service options for disa/e&m – retrieve par...
Page 1119
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1087 21-05-08 toll restriction class – restriction table set the tables 1~4 when referring to the table set up by program 21-06-07. 1~4 =table 0 = disable (none) default: 1, 2, 6~15 = 0 3 = 1 4 = 2 5 = 3 21-05-09 toll restriction class – restrictio...
Page 1120
Issue 11.0 univerge sv8100 2 - 1088 multiple trunk types 22-02-01 incoming call trunk setup set the feature type for the trunk you are programming. For each night service mode, enter 5 when the trunk should be an e&m tie line. 0 = normal 1 = vrs (second dial tone if no vrs installed) 2 = disa 3 = di...
Page 1121
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1089 34-04-01 e&m tie line toll restriction class if the system uses toll restriction, enter a toll restriction class (1~15) for each tie line. The system uses the class you enter in program 21-05 and 21-06. Make a separate toll restriction class e...
Page 1122
Issue 11.0 univerge sv8100 2 - 1090 multiple trunk types 80-03-01 dtmf tone receiver setup – detect level use items 11~32 to set the criteria for dial tone detection for outgoing ars calls. 0 = 0dbm ~ -25dbm 1 = -5dbm ~ -30dbm 2 = -10dbm ~ -35dbm 3 = -15dbm ~ -40dbm 4 = -20dbm ~ -45dbm 5 = -25dbm ~ ...
Page 1123
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1091 80-03-03 dtmf tone receiver setup – min. Detect level define the minimum detection level for dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20dbm(0) to – 35dbm(15) det...
Page 1124
Issue 11.0 univerge sv8100 2 - 1092 multiple trunk types 80-03-04 dtmf tone receiver setup – max. Detect level define the maximum detection level for dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(0) to – 25dbm(15) detect...
Page 1125
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1093 80-03-05 dtmf tone receiver setup – forward twist level define the forward twist level for dtmf tone receiver. 0~9 (1db~10db) default: type 1~5 = 5 (6dbm) 80-03-06 dtmf tone receiver setup – backwards twist level define the backwards twist lev...
Page 1126
Issue 11.0 univerge sv8100 2 - 1094 multiple trunk types 80-04-02 call progress tone detector setup – min. Detection level define the minimum detection levels for the call progress tone detector. 0~15 detect level 0: –15dbm(0) to –30dbm(15) detect level 1: –30dbm(0) to –45dbm(15) detect level 2: –40...
Page 1127
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1095 80-04-05 call progress tone detector setup – pulse count define the pulse count for the call progress tone detector. 1~255 default: type 1 (dt) – 1 type 2 (bt) – 1 type 3 (rbt) – 1 type 4, type 5 – 0 80-04-06 call progress tone detector setup ...
Page 1128
Issue 11.0 univerge sv8100 2 - 1096 multiple trunk types 81-11-01 tie line initial setup – dp interdigit time selection select the dp interdigit time (minimum pause time between dial pulses). 0 = pattern a (pattern a: 10pps – 650ms, 20pps - 500ms) 1 = pattern b (pattern b: 10pps – 800ms, 20pps - 800...
Page 1129
Univerge sv8100 issue 11.0 multiple trunk types 2 - 1097 operation none 81-11-08 tie line initial setup – length of delay signal selection specify the time a delay pulse is sent to another system. 1~15 (300 ms~4.5 seconds) (0 = no setting) [default = 1 (300ms)] 81-11-09 tie line initial setup – inco...
Page 1130
Issue 11.0 univerge sv8100 2 - 1098 multiple trunk types this page intentionally left blank.
Page 1131: Music On Hold
Univerge sv8100 issue 11.0 music on hold 2 - 1099 music on hold description music on hold (moh) sends music to calls on hold and parked calls. The music lets the caller know that the call is waiting, not forgotten. Without music on hold, the system provides silence to these types of calls. The music...
Page 1132
Issue 11.0 univerge sv8100 2 - 1100 music on hold system availability terminals none required component(s) optional – pgd(2)-u10 adp optional – locally provided background music source (i.E., cd player, radio, nec audio emcee). Related features none guide to feature programming the level 1, level 2 ...
Page 1133
Univerge sv8100 issue 11.0 music on hold 2 - 1101 10-04-02 music on hold setup – music on hold tone selection when program 10-04-01 is set to internal moh, define the music that is played for music on hold. [when item 1 is 0] 1 = download file1 2 = download file2 3 = download file3 [when item 1 is 1...
Page 1134
Issue 11.0 univerge sv8100 2 - 1102 music on hold 20-07-02 class of service options (administrator level) – changing the music on hold tone turn off or on an extension user ability to change the music on hold tone. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for cos 15) 22-11-09 did trans...
Page 1135
Univerge sv8100 issue 11.0 music on hold 2 - 1103 when using a pgd(2)-u10 adp: program number program name description/comments assigned data level 1 2 3 10-03-01 etu setup (dlca pkg setup) – terminal type (b1) if a pgd(2)-u10 adp is used for the external music source, the module is automatically as...
Page 1136
Issue 11.0 univerge sv8100 2 - 1104 music on hold 33-02-01 aci department calling group assign aci software ports to an aci department group. This lets aci callers connect to aci software ports by dialing the group pilot number (set in program 11-08). Aci ports: 1~96 aci groups: 1~16 default: aci po...
Page 1137
Univerge sv8100 issue 11.0 music on hold 2 - 1105 communications interface feature for more.
Page 1138
Issue 11.0 univerge sv8100 2 - 1106 music on hold.
Page 1139
Univerge sv8100 issue 11.0 music on hold 2 - 1107 operation none.
Page 1140
Issue 11.0 univerge sv8100 2 - 1108 music on hold this page intentionally left blank.
Page 1141: Name Storing
Name storing 2 - 1109 n name storing description extensions and trunks can have names instead of just circuit numbers. These names show on a multiline terminal display when the user places or answers calls. Extension and trunk names make it easier to identify callers. The user does not have to refer...
Page 1142
Issue 11.0 univerge sv8100 2 - 1110 name storing required component(s) none related features directory dialing single line telephones, analog 500/2500 sets speed dial – system/group/station guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned ...
Page 1143
Univerge sv8100 issue 11.0 name storing 2 - 1111 20-09-02 class of service options (incoming call service) – caller id display turn off or on the caller id display at an extension. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-21 class of service options (supplementary service) – extension name tu...
Page 1145: Night Service
Univerge sv8100 issue 11.0 night service 2 - 1113 night service description night service lets system users activate one of the night service modes. Night service redirects calls to their night mode destination, as determined by assigned and universal night answer programming. A user typically activ...
Page 1146
Issue 11.0 univerge sv8100 2 - 1114 night service you may also use transfer to una. An extension user can transfer their call to una (i.E., external paging at night). Once transferred, the call rings the external paging speakers like any other una call and can be picked up at any extension. You can ...
Page 1147
Univerge sv8100 issue 11.0 night service 2 - 1115 when programming night service function keys, multiple keys must be used for switching between each night service mode. Virtual extension ring assignment (command 15-09) follows the ring assignment for the night mode group the virtual extension is as...
Page 1148
Issue 11.0 univerge sv8100 2 - 1116 night service guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature prog...
Page 1149
Univerge sv8100 issue 11.0 night service 2 - 1117 12-02-02 automatic night service – end time for each night service group (01~32), enter up to 20 end times (0000~2359) for each time pattern (1~10). 0000~2359 please refer to the sv8100 programming manual for default settings. 12-02-03 automatic nigh...
Page 1150
Issue 11.0 univerge sv8100 2 - 1118 night service 12-05-01 night mode group assignment for extensions assign a day/night mode group (01~32), for each extension. Night mode service group number: 01~32 (default = 1) 12-06-01 night mode group assignment for trunks assign a day/night mode group (01~32),...
Page 1151
Univerge sv8100 issue 11.0 night service 2 - 1119 14-07-01 trunk access map setup to allow for universal night answer (una) answering, set up the trunk access maps (1~200). For una, extension must have incoming access to trunk ringing the external paging speakers. 0 = no access 1 = outgoing access o...
Page 1152
Issue 11.0 univerge sv8100 2 - 1120 night service 20-06-01 class of service for extensions assign a class of service (1~15) to an extension. Day night/mode: 1~8 class of service of extensions (1~15) default: extension port 101 = class 15 all other extension port = class 1 20-07-01 class of service o...
Page 1153
Univerge sv8100 issue 11.0 night service 2 - 1121 operation to activate night service by dialing codes: 1. At a multiline terminal, press speaker. - or - at the single line telephone, lift the handset. 2. Dial 718. To change a different group’s mode, dial 718 + the group number (01~32). 3. Dial the ...
Page 1154
Issue 11.0 univerge sv8100 2 - 1122 night service to activate night service by using programmable keys: 1. Press night service key (program 15-07-01 or sc 751:09 + mode code number below). 1 = day 1 mode 2 = night 1 mode 3 = midnight 1 mode 4 = rest 1 mode 5 = day 2 mode 6 = night 2 mode 7 = midnigh...
Page 1155: Off-Hook Signaling
Off-hook signaling 2 - 1123 o off-hook signaling description off-hook ringing alerts a multiline terminal user that an incoming outside call is ringing to that station during another call. Off-hook signaling helps important callers get through, without waiting in line for the called extension to bec...
Page 1156
Issue 11.0 univerge sv8100 2 - 1124 off-hook signaling block manual off-hook signals this class of service option enables/disables a busy extension ability to block off-hook signals manually sent from a co-worker. If disabled (not blocked), callers can dial at busy or busy/ring to signal the extensi...
Page 1157
Univerge sv8100 issue 11.0 off-hook signaling 2 - 1125 system availability terminals all multiline terminals and single line telephones required component(s) none related features callback call waiting/camp-on direct inward dialing (did) handsfree and monitor hotline intercom one-touch calling progr...
Page 1158
Issue 11.0 univerge sv8100 2 - 1126 off-hook signaling guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 1159
Univerge sv8100 issue 11.0 off-hook signaling 2 - 1127 20-09-07 class of service options (incoming call service) – call queuing turn off or on an extension ability to have calls queued if a call rings the extension when it is busy. Must be set to 1 to enable automatic off-hook signaling. 0 = off 1 =...
Page 1160
Issue 11.0 univerge sv8100 2 - 1128 off-hook signaling operation to send off-hook signals to an extension busy on a call: your extension may send off-hook signals automatically. 1. Dial 7. - or - press off-hook signaling key (program 15-07 or sc 751: 33). You hear ringback. To have your call voice-a...
Page 1161: One-Touch Calling
Univerge sv8100 issue 11.0 one-touch calling 2 - 1129 one-touch calling description one-touch calling gives a multiline terminal user one-button access to extensions, trunks, speed dial bins and selected system features. This saves users time when accessing co-workers, clients and features they use ...
Page 1162
Issue 11.0 univerge sv8100 2 - 1130 one-touch calling the @ can be entered in the dial string of a dss/one touch button. The @ only applies to isdn and intercom calls. When using the @, the system waits for the destination to answer (answer supervision), and then sends the rest of the digits. Enteri...
Page 1163
Univerge sv8100 issue 11.0 one-touch calling 2 - 1131 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature ...
Page 1164
Issue 11.0 univerge sv8100 2 - 1132 one-touch calling operation programmable function keys: to define a programmable function key as a one-touch key: 1. Dial the service code for function key programming (program 11-11-17, 751 by default). 2. Press the key to be defined. 3. Dial 01 (dss/one-touch ke...
Page 1165
Univerge sv8100 issue 11.0 one-touch calling 2 - 1133 for central office calls, placing (trunk calling): a. A. Dial the general trunk access code (9). - or - dial the specific trunk service code (#9) plus the trunk number (e.G., 005). - or - dial the trunk group service code (704) plus the trunk gro...
Page 1166
Issue 11.0 univerge sv8100 2 - 1134 one-touch calling this page intentionally left blank.
Page 1167: Operator
Univerge sv8100 issue 11.0 operator 2 - 1135 operator description when an extension user dials 0, calls are routed to a main system operator. The operator can answer and route outside calls or locate employees using the page feature. A maximum of eight operators is available. Conditions attendant ex...
Page 1168
Issue 11.0 univerge sv8100 2 - 1136 operator related features attendant call queuing guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro ...
Page 1169
Univerge sv8100 issue 11.0 operator 2 - 1137 operation refer to the individual features for operation..
Page 1170
Issue 11.0 univerge sv8100 2 - 1138 operator this page intentionally left blank.
Page 1171: (Opx) Off-Premise Extension
Univerge sv8100 issue 11.0 (opx) off-premise extension 2 - 1139 (opx) off-premise extension description off-premise extension allows a single line telephone, located remotely from the main installation site, to access the system features with the same abilities as an on-premise single line telephone...
Page 1172
Issue 11.0 univerge sv8100 2 - 1140 (opx) off-premise extension guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards fo...
Page 1173
Univerge sv8100 issue 11.0 (opx) off-premise extension 2 - 1141 15-03-03 single line telephone basic data setup – terminal type enter 1 for this option to allow a single line port to receive dtmf tones after the initial call setup. Enter 0 to have the port ignore dtmf tones after the initial call se...
Page 1174
Issue 11.0 univerge sv8100 2 - 1142 (opx) off-premise extension 20-03-01 system options for single line telephones – slt call waiting answer mode for a busy single line (500/2500 type) telephone, set the mode used to answer a camped-on trunk call. For esl sets, enabling this option (1) allows the us...
Page 1175
Univerge sv8100 issue 11.0 (opx) off-premise extension 2 - 1143 20-03-06 system options for single line telephones – headset ringing start time (for slt) define the headset ringing start time. After this time expires after a single line telephone is off-hook, the system sets the single line telephon...
Page 1176
Issue 11.0 univerge sv8100 2 - 1144 (opx) off-premise extension 80-03-03 dtmf tone receiver setup – min. Detect level define the minimum detection level for dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20dbm(0) to – 35dbm(...
Page 1177
Univerge sv8100 issue 11.0 (opx) off-premise extension 2 - 1145 80-03-04 dtmf tone receiver setup – max. Detect level define the maximum detection level for dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(0) to – 25dbm(15)...
Page 1178
Issue 11.0 univerge sv8100 2 - 1146 (opx) off-premise extension 80-03-05 dtmf tone receiver setup – forward twist level define the forward twist level for dtmf tone receiver. 0~9 (1db~10db) default: type 1 = 5 (6dbm) type 2 = 5 (6dbm) type 3 = 5 (6dbm) type 4 = 5 (6dbm) type 5 = 5 (6dbm) 80-03-06 dt...
Page 1179
Univerge sv8100 issue 11.0 (opx) off-premise extension 2 - 1147 refer to single line telephones, analog 500/2500 sets on page 2-1321 for related programming. Operation normal call handling procedures for single line telephones apply. 80-04-04 call progress tone detector setup – no tone time define t...
Page 1180
Issue 11.0 univerge sv8100 2 - 1148 (opx) off-premise extension this page intentionally left blank.
Page 1181: Paging, External
Paging, external 2 - 1149 p paging, external description with external paging, a user can broadcast announcements over paging equipment connected to external paging zones. When a user pages one of these external zones, the system broadcasts the announcement over the speakers. Like internal paging, e...
Page 1182
Issue 11.0 univerge sv8100 2 - 1150 paging, external did and dil trunks do not ring external page speakers. Only trunks defined as normal in program 22-02-01 ring external page speakers. Paging keys can be assigned on programmable function keys and direct station selection (dss) consoles to simplify...
Page 1183
Univerge sv8100 issue 11.0 paging, external 2 - 1151 related features central office calls, placing direct inward dialing (did) direct inward line (dil) direct station selection (dss) console door box night service paging, internal programmable function keys transfer guide to feature programming the...
Page 1184
Issue 11.0 univerge sv8100 2 - 1152 paging, external 10-21-04 cd-cp00-us hardware setup – external source i/o selection on cd-cp00-us define how the i/o ports on the cd-cp00-us are used. 0 = external moh (cn8)/ external speaker(cn9) 1 = bgm source (cn8)/ external speaker(cn9) 2 = external moh (cn8)/...
Page 1185
Univerge sv8100 issue 11.0 paging, external 2 - 1153 31-04-01 external paging zone group assign each external paging speaker to an external paging group (1~8) used for accessing the zone. If zones 1~8 are not connected to pgd(2)-u10 adp, set these unused zones to external paging group 0. External pa...
Page 1186
Issue 11.0 univerge sv8100 2 - 1154 paging, external operation to page into an external zone: 1. Press external paging key (program 15-07 or sc 751: 19 for external paging zones or 20 for external all call paging). 2. Make announcement. - or - 1. At the multiline terminal, press speaker or pick up t...
Page 1187
Univerge sv8100 issue 11.0 paging, external 2 - 1155 4. Dial 703 and the external paging zone code (1~8 or 0 for all call). - or - dial 1 and the combined paging group code (1~8 or 0 for internal/external all call). Display indicates the combined paging as an external page. If the internal page zone...
Page 1188
Issue 11.0 univerge sv8100 2 - 1156 paging, external this page intentionally left blank.
Page 1189: Paging, External (Vrs)
Univerge sv8100 issue 11.0 paging, external (vrs) 2 - 1157 paging, external (vrs) description paging, external (vrs) enables the use of prerecorded vrs messages for external paging. The advantage of this feature is saving time for the users who regularly use external paging with the same announcemen...
Page 1190
Issue 11.0 univerge sv8100 2 - 1158 paging, external (vrs) system availability terminals all multiline terminals single line telephones cordless terminals isdn terminals h.323 terminals standard sip terminals required component(s) pz-vm21 vm8000 inmail compact flash cpu license for vrs cd-8dlca, cd-...
Page 1191
Univerge sv8100 issue 11.0 paging, external (vrs) 2 - 1159 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for fea...
Page 1192
Issue 11.0 univerge sv8100 2 - 1160 paging, external (vrs) 3. Dial vrs message number (001-100). 4. Make announcement. 5. Press speaker at multiline terminal or on-hook. - or - 1. Press dss/one touch key programmed for external paging. To program one touch key: the following example shows how to pro...
Page 1193: Paging, Internal
Univerge sv8100 issue 11.0 paging, internal 2 - 1161 paging, internal description internal paging lets extension users broadcast announcements to other multiline terminal users. When a user makes a zone paging announcement, the announcement broadcasts to all idle extensions in the zone dialed. With ...
Page 1194
Issue 11.0 univerge sv8100 2 - 1162 paging, internal if auto hold in program 15-02-07 is set to cut (1), when a user presses the page key while on a trunk call, the trunk call is put on hold. A single line telephone can initiate an internal zone page, but cannot receive an internal zone page. If an ...
Page 1195
Univerge sv8100 issue 11.0 paging, internal 2 - 1163 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature p...
Page 1196
Issue 11.0 univerge sv8100 2 - 1164 paging, internal operation to make an internal page announcement: multiline terminal 1. Press the zone internal paging key (program 15-07 or sc 751: 21 + 0 or 1~9 or 01~64 for zones (0 or 00 for all call). - or - press speaker or lift the handset. 31-02-01 interna...
Page 1197
Univerge sv8100 issue 11.0 paging, internal 2 - 1165 2. Dial 701 and the paging zone number (0~9 or 00~64). Dialing 0 or 00 calls all call internal paging. - or - dial 1 and the combined paging group code 1~8 or 0 (for internal/external all call). Display indicates the combined paging as an external...
Page 1198
Issue 11.0 univerge sv8100 2 - 1166 paging, internal this page intentionally left blank.
Page 1199: Park
Univerge sv8100 issue 11.0 park 2 - 1167 park description park places a call in a wait state (called a park orbit) so an extension user may pick it up. Park has two types: system and personal. System park allows a user to have a call wait in system orbit. Personal park allows a user to park a call a...
Page 1200
Issue 11.0 univerge sv8100 2 - 1168 park when the terminal that has a call in personal park is unplugged, the personal park is released and the held caller is placed on non-exclusive hold. The following table indicates what condition the service codes and programmable function key can be used. A use...
Page 1201
Univerge sv8100 issue 11.0 park 2 - 1169 personal park at a co-worker’s extension description the personal park feature allows an extension user to place an outside call, which is on hold, on personal park at a co-worker’s extension after placing an intercom call. This feature is available for keyse...
Page 1202
Issue 11.0 univerge sv8100 2 - 1170 park required component(s) none related features caller id call arrival (car) keys direct station selection (dss) console hold programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned ...
Page 1203
Univerge sv8100 issue 11.0 park 2 - 1171 15-02-08 multiline telephone basic data setup – automatic handsfree set whether pressing a one-touch key preselects the key or goes off-hook to access the key. 0 = preselect 1 = one-touch (automatic handsfree) (default = 1) 15-07-01 programmable function keys...
Page 1204
Issue 11.0 univerge sv8100 2 - 1172 park 20-11-25 class of service options (hold/ transfer service) – transfer park call turn off or on an extension user ability to transfer a parked call. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-26 class of service options (hold/ transfer service) – station ...
Page 1205
Univerge sv8100 issue 11.0 park 2 - 1173 operation to park a call in a system orbit: you can park intercom or trunk calls. 1. Press the park key (program 15-07 or sc 752: 04 + orbit). The park key led lights. If you hear busy tone, the orbit is busy. Try another orbit. 2. Use paging to announce call...
Page 1206
Issue 11.0 univerge sv8100 2 - 1174 park to park a call at your extension: 1. Press hold and dial 757. - or - press hold and the personal park key (program 15-07 or sc 752: 07). At a 500/2500 single line telephone, hookflash instead of pressing hold. A confirmation tone is heard and the call is park...
Page 1207
Univerge sv8100 issue 11.0 park 2 - 1175 3. Press the personal park key (program 15-07 or sc 752: 07). - or - press the stap soft key h. - or - dial the personal park single digit code (program 11-16-11). The intercom call to the co-worker is dropped. A confirmation tone is heard and the call is par...
Page 1208
Issue 11.0 univerge sv8100 2 - 1176 park 4. Press speaker to hang up. If not picked up, the call will recall to you. - or - 1. Press hold or transfer. 2. Press the dss/blf key programmed as # 6 (the park location will be displayed in the lcd). 3. Press speaker to hang up..
Page 1209: Pbx Compatibility
Univerge sv8100 issue 11.0 pbx compatibility 2 - 1177 pbx compatibility description you can connect your telephone system trunks to centrex/pbx lines, rather than to telco trunk circuits. This makes the trunk inputs to the system 500/2500 type compatible centrex/pbx extensions, rather than telco cir...
Page 1210
Issue 11.0 univerge sv8100 2 - 1178 pbx compatibility except for dialing the pbx access code, users place calls on pbx trunks just like other trunks. All relevant access programming applies. Refer to the central office calls, placing on page 2-273 feature for more details. You can have dils route fr...
Page 1211
Univerge sv8100 issue 11.0 pbx compatibility 2 - 1179 central office calls, answering central office calls, placing code restriction direct inward line (dil) direct inward system access (disa) flash pulse to tone conversion ring groups speed dial – system/group/station trunk group routing trunk grou...
Page 1212
Issue 11.0 univerge sv8100 2 - 1180 pbx compatibility 14-01-02 basic trunk data setup – transmit level set these options for compatibility with the connected pbx. Trunks 1~200 1~63 (-15.5 ~ +15.5db in 0.5db intervals) [default = 32 (0db)] 14-01-08 basic trunk data setup – toll restriction for each p...
Page 1213
Univerge sv8100 issue 11.0 pbx compatibility 2 - 1181 operation to place a call over a pbx trunk: 1. At multiline terminal, press speaker and dial 704. - or - at single line telephone, lift the handset and dial 704. 2. Dial pbx trunk group number (1~9 or 001~100). 3. Dial pbx access code and number....
Page 1214
Issue 11.0 univerge sv8100 2 - 1182 pbx compatibility this page intentionally left blank.
Page 1215: Pc Programming
Univerge sv8100 issue 11.0 pc programming 2 - 1183 pc programming description the univerge sv8100 has three different methods for programming. The first is via the handset, the second is by pcpro and third by webpro. Pcpro is a microsoft windows based application. It allows the technician/system adm...
Page 1216
Issue 11.0 univerge sv8100 2 - 1184 pc programming an overview of the three programming applications is shown below. Connecting as can be seen in figure 2-30 pc programming overview , three connection types are available to pcpro/webpro. If using pcpro, a user can connect directly, remotely using a ...
Page 1217
Univerge sv8100 issue 11.0 pc programming 2 - 1185 figure 2-31 pcpro connection dialog 3) (optional) load a defined connection account (can skip steps 1~3 by using this option. 1) select connection type. If connecting to an ipk ii system, select either direct or modem connection type. 2) to login, s...
Page 1218
Issue 11.0 univerge sv8100 2 - 1186 pc programming if using webpro, a user can connect only via ip. To connect, launch internet explorer and enter the ip address of the switch (refer to figure 2-32 webpro login screen ). Webpro system programming webpro can be used to edit system programming from a ...
Page 1219
Univerge sv8100 issue 11.0 pc programming 2 - 1187 with version 4000 or higher, the maintenance debug section is added to allow the webpro user to turn on debug traces for engineering troubleshooting (refer to figure 2-34 maintenance debug screen ). Figure 2-33 webpro home page figure 2-34 maintenan...
Page 1220
Issue 11.0 univerge sv8100 2 - 1188 pc programming webpro end user programming webpro has an end user login for which extensions can program functions for their own extension. They can program function keys, virtual extension ringing assignment, station speed dial, inmail features, station name, cal...
Page 1221
Univerge sv8100 issue 11.0 pc programming 2 - 1189 when connecting via a dial up connection, a dial up connection (ppp) must be configured in windows network connections. When uploading via a dial up connection, uploading card configuration (hardware upload) is not supported. The hardware/software r...
Page 1222
Issue 11.0 univerge sv8100 2 - 1190 pc programming you can have four webpro users and two phone programming users logged in at the same time for a total of six users in programming mode simultaneously. However, the two phone programming users do not show up in session management in webpro. Pcpro can...
Page 1223
Univerge sv8100 issue 11.0 pc programming 2 - 1191 pcpro converts an electra elite ipk ii pcpro database file into a sv8100 pcpro database file. Pcpro software version 3.00 or higher is required. The system data to be converted is limited to the system data listed below. Prg no. Name 10-23 ip system...
Page 1224
Issue 11.0 univerge sv8100 2 - 1192 pc programming pcpro can open and convert a ux5000 database to an sv8100 database (version 4.00 pcpro or higher is required). Refer to the pcpro manual for programs converted. Databases that have a pz-me50-us installed can not be uploaded into a system without a p...
Page 1225
Univerge sv8100 issue 11.0 pc programming 2 - 1193 outbound ip connection description outbound ip connection for pc programming allows the system to make a pc pro connection via an outgoing call over ip, to a pre-programmed ip address, upon receipt of an incoming co call matching a pre-programmed cl...
Page 1226
Issue 11.0 univerge sv8100 2 - 1194 pc programming system availability terminals all terminals required software none required component(s) cpu pc programming r6000 enhancement (0035) license (for outbound ip connection) maintenance (0043) license (for outbound ip connection) related features alarm ...
Page 1227
Univerge sv8100 issue 11.0 pc programming 2 - 1195 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pro...
Page 1228
Issue 11.0 univerge sv8100 2 - 1196 pc programming 10-12-02 cd-cp00-us network setup – subnet mask the setting of subnet mask is invalid when all host addresses are 0. If the network section is: 0, 127, 128.0, 191.255, 192.0.0, 223.255.255 the setting of subnet mask is invalid. 128.0.0.0 192.0.0.0 2...
Page 1229
Univerge sv8100 issue 11.0 pc programming 2 - 1197 22-02-01 incoming call trunk setup define the service type for the trunk intended to access the internal modem as 4:dil. 0 = normal 1 = vrs (second dial tone if no vrs installed) 2 = disa 3 = did 4 = dil 5 = e&m tie line 6 = delayed vrs 7 = ani/dnis...
Page 1230
Issue 11.0 univerge sv8100 2 - 1198 pc programming outbound ip connection: 90-02-03 programming password setup – user level set the system password user levels. 0 = prohibited user 1 = mf (manufacturer level) 2 = in (installer level) 3 = sa (system administrator level 1) 4 = sb (system administrator...
Page 1231
Univerge sv8100 issue 11.0 pc programming 2 - 1199 operation outbound ip connection 1. Open pc pro (v6000 or higher) on pc that has same ip address as assigned in program 90-69-02. 2. Go to communications/connect. 11-15-16 service code setup, administrative (for special access) – outbound ip connect...
Page 1232
Issue 11.0 univerge sv8100 2 - 1200 pc programming 3. Select outbound ip. 4. Input connection port (same as program 90-69-01). 5. Select connect. When pcpro does not receive a tcp established request within three minutes (fixed time), it ends the state of "attempting to connect". 6. Dial outbound ip...
Page 1233
Univerge sv8100 issue 11.0 pc programming 2 - 1201 remote connection upload y – pcpro can download the database from the univerge sv8100 to allow backups. Download y – connection accounts y – pcpro supports direct, modem and ip connections. Webpro supports only ip. Accounts y y webpro: refer to prog...
Page 1234
Issue 11.0 univerge sv8100 2 - 1202 pc programming configuration screens blade configuration y – pcpro provides special screens that shorten the programming time to setup core univerge sv8100 features. Class of service y – night mode switching y – trunk access maps y – trunk groups y – department gr...
Page 1235
Univerge sv8100 issue 11.0 pc programming 2 - 1203 debug/capture cd-cp00-us debug capture y – pcpro provides a tool for capturing debug information from the univerge sv8100 cd-cp00-us. Smdr capture y – pcpro provides a tool for capturing smdr reports from the univerge sv8100. Modification history y ...
Page 1236
Issue 11.0 univerge sv8100 2 - 1204 pc programming this page intentionally left blank.
Page 1237: Power Failure Transfer
Univerge sv8100 issue 11.0 power failure transfer 2 - 1205 power failure transfer description power failure transfer ensures that a customer has access to the central office network during a power outage. The co/pbx tip and ring are automatically transferred to a dth or ith terminal multiline termin...
Page 1238
Issue 11.0 univerge sv8100 2 - 1206 power failure transfer a power fail circuit is required. The cd-4cotb has power failure circuits on the first two ports. The pz-4cotf daughter board does not have power fail or fax branch exchange circuits. Default setting none system availability terminals all mu...
Page 1239
Univerge sv8100 issue 11.0 power failure transfer 2 - 1207 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for fea...
Page 1240
Issue 11.0 univerge sv8100 2 - 1208 power failure transfer this page intentionally left blank.
Page 1241: Prime Line Selection
Univerge sv8100 issue 11.0 prime line selection 2 - 1209 prime line selection description prime line selection allows a multiline terminal user to place or answer a call over a specific trunk by lifting the handset. The user does not have to press keys or dial codes. This simplifies handling calls o...
Page 1242
Issue 11.0 univerge sv8100 2 - 1210 prime line selection required component(s) none related features central office calls, placing direct inward dialing (did) direct inward line (dil) direct inward system access (disa) line preference guide to feature programming the level 1, level 2 and level 3 col...
Page 1243
Univerge sv8100 issue 11.0 prime line selection 2 - 1211 14-06-01 trunk group routing – priority order number set the priority order number 1~4. 0 = not specify 1~100 : (trunk group number) 1001~1100 : (1000 + route table number) default: route 1, order number 1 = 1 (trunk group 1) order numbers 2, ...
Page 1244
Issue 11.0 univerge sv8100 2 - 1212 prime line selection 15-02-10 multiline telephone basic data setup – ringing line preference for trunk calls enter 1 if lifting the handset should answer ringing prime line; enter 0 to seize idle line appearance. 0 = idle (off) 1 = ringing (on) (default = 1) 15-06...
Page 1245
Univerge sv8100 issue 11.0 prime line selection 2 - 1213 operation to place a call on your prime line: 1. Lift the handset. You hear dial tone on your prime line. To answer a call on your prime line: 1. Lift the handset. Depending on your line preference programming, you either answer the prime line...
Page 1246
Issue 11.0 univerge sv8100 2 - 1214 prime line selection this page intentionally left blank.
Page 1247: Private Line
Univerge sv8100 issue 11.0 private line 2 - 1215 private line description a private line is a trunk reserved for a multiline terminal for placing and answering calls. Users with a private line always know when important calls are for them. Additionally, the user has their own trunk for placing calls...
Page 1248
Issue 11.0 univerge sv8100 2 - 1216 private line system availability terminals all terminals required component(s) none related features call forwarding central office calls, placing do not disturb line preference prime line selection programmable function keys single line telephones, analog 500/250...
Page 1249
Univerge sv8100 issue 11.0 private line 2 - 1217 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progr...
Page 1250
Issue 11.0 univerge sv8100 2 - 1218 private line 14-07-01 trunk access map setup – trunk port number assign private line to the private line access map (refer to program 15-06 in this section). Use option 5 for incoming, option 7 for both ways and option 4 for outgoing. In all other access maps, ass...
Page 1251
Univerge sv8100 issue 11.0 private line 2 - 1219 operation to place a call on your private line: 1. Press private line key and then press speaker or lift the handset. 2. Dial the number. 22-02-01 incoming call trunk setup set the trunk service to type 4 if routing unanswered private lines to voice m...
Page 1252
Issue 11.0 univerge sv8100 2 - 1220 private line to answer a call on your private line: 1. Press private line key, and then press speaker or lift handset. To place a call from your multiline terminal on you private line: 1. Press the private line key, then press speaker or lift the handset. 2. Dial ...
Page 1253: Programmable Function Keys
Univerge sv8100 issue 11.0 programmable function keys 2 - 1221 programmable function keys description each multiline terminal has programmable function keys. Programmable function keys simplify placing calls, answering calls and using certain features. You can customize the function of a multiline t...
Page 1254
Issue 11.0 univerge sv8100 2 - 1222 programmable function keys if the feature key is not listed below, the lcd shows all-blank. (program 15-07-01 line key assign). One-touch keys programmed for park hold service code cannot be used to park calls without using hold or transfer. Pauses can be entered ...
Page 1255
Univerge sv8100 issue 11.0 programmable function keys 2 - 1223 if you change the extension assigned to a port in program 11-02, the line key programming does not follow. However, if you move the extension using the station relocation feature, the line key programming does follow. In order for a stat...
Page 1256
Issue 11.0 univerge sv8100 2 - 1224 programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for...
Page 1257
Univerge sv8100 issue 11.0 programmable function keys 2 - 1225 operation to change a 2-digit programmable key: 1. Press speaker. 2. Dial 751 for 2-digit codes. 3. Press the key you want to program. 4. Enter the 2-digit key function, any additional information needed for the key and press hold. For a...
Page 1258
Issue 11.0 univerge sv8100 2 - 1226 programmable function keys 4. Enter the 3-digit key function and any additional information needed for the key. For available functions codes, refer to program 15-07 in the univerge sv8100 programing manual. To undefine a key, enter 000. When a key is programmed u...
Page 1259
Univerge sv8100 issue 11.0 programming from a multiline terminal 2 - 1227 programming from a multiline terminal description system programming can be performed from any display multiline terminal. Most programming changes become effective immediately. Other programming changes become effective after...
Page 1260
Issue 11.0 univerge sv8100 2 - 1228 programming from a multiline terminal system availability terminals all multiline terminals with display required component(s) any dlc blade required software none related features pc programming guide to feature programming the level 1, level 2 and level 3 column...
Page 1261
Univerge sv8100 issue 11.0 programming from a multiline terminal 2 - 1229 operation refer to the univerge sv8100 programming manual for additional information. 90-02-02 programming password setup – password configure the administrator accounts that are used when connecting to the kts via pcpro/ webp...
Page 1262
Issue 11.0 univerge sv8100 2 - 1230 programming from a multiline terminal this page intentionally left blank.
Page 1263: Pulse to Tone Conversion
Univerge sv8100 issue 11.0 pulse to tone conversion 2 - 1231 pulse to tone conversion description an extension can use pulse to tone conversion on trunk calls. Pulse to tone conversion lets a user change their extension dialing mode while placing a call. For systems in a dial pulse area, this permit...
Page 1264
Issue 11.0 univerge sv8100 2 - 1232 pulse to tone conversion required component(s) cd-4cotb, pz-4cotf - or - cd-4odta - or - cd-ccta related features central office calls, placing multiple trunk types guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that ar...
Page 1265
Univerge sv8100 issue 11.0 pulse to tone conversion 2 - 1233 operation to convert your telephone dialing to tone after placing your call on a pulse line: 1. Place a call over pulse line. 2. Dial # to switch the dp trunk to dtmf dialing..
Page 1266
Issue 11.0 univerge sv8100 2 - 1234 pulse to tone conversion this page intentionally left blank.
Page 1267: Redial Function
Redial function 2 - 1235 r redial function description users can press redial to cycle through the last 10 outside numbers dialed. Pressing # redials the number displayed. Users can also press redial and dial a system speed dial bin number to access system speed dial. Conditions redial list requires...
Page 1268
Issue 11.0 univerge sv8100 2 - 1236 redial function required component(s) none related features last number redial speed dial – system/group/station guide to feature programming none operation to redial the last number dialed: for elite ipk telephones only: 1. Press redial. Redial [#] / sys is displ...
Page 1269
Univerge sv8100 issue 11.0 redial function 2 - 1237 3. Press the up and down arrow to view the number to dial. 4. Press the # key or press speaker or lift the handset or press and idle trunk key. To scroll through the last 10 outside numbers dialed: 1. Press redial. Each time the redial key is press...
Page 1270
Issue 11.0 univerge sv8100 2 - 1238 redial function 2. Tap the cursor key up or down to refresh the list, if the redialed number has a matching common or group speed dial bin associated with it, the name information from program13-04-02 is displayed. 3. Press speaker or lift the handset to dial the ...
Page 1271: Remote (System) Upgrade
Univerge sv8100 issue 11.0 remote (system) upgrade 2 - 1239 remote (system) upgrade description with pc programming, the univerge sv8100 can be remotely upgraded to a newer version of main system software. When a new version of main system software is released, a firmware package file is provided. U...
Page 1272
Issue 11.0 univerge sv8100 2 - 1240 remote (system) upgrade up to two versions of firmware are kept on the usb drive. One version is the current version that the cd-cp00-us used to boot up from. The other version is the new version that is used on the next boot up. If the boot up fails when switchin...
Page 1273
Univerge sv8100 issue 11.0 remote (system) upgrade 2 - 1241 operation pcpro: 1. Obtain the firmware package file from nec. 2. Open and login to pcpro. 3. Connect to the system. 4. Under the communications menu, choose the firmware update option. Until connected to the system the firmware update opti...
Page 1274
Issue 11.0 univerge sv8100 2 - 1242 remote (system) upgrade this page intentionally left blank.
Page 1275: Repeat Redial
Univerge sv8100 issue 11.0 repeat redial 2 - 1243 repeat redial description if a multiline terminal user places a trunk call that is busy or unanswered, they can have repeat redial try it again later on. The user does not continually have to try the number again – hoping it goes through. Repeat redi...
Page 1276
Issue 11.0 univerge sv8100 2 - 1244 repeat redial related features automatic route selection central office calls, placing last number redial save number dialed single line telephones, analog 500/2500 sets guide to feature programming the level 1, level 2 and level 3 columns indicate the programs th...
Page 1277
Univerge sv8100 issue 11.0 repeat redial 2 - 1245 operation to use repeat redial (if the outside party you call is unavailable or busy): 1. Place a trunk call. Listen for busy tone or ring no answer. 2. Press feature + redial. - or - press the repeat redial key (program 15-07 or sc 751: 29). Repeat ...
Page 1278
Issue 11.0 univerge sv8100 2 - 1246 repeat redial to cancel repeat redial: 1. Press feature. 2. Press redial. - or - 1. Press repeat redial key (program 15-07 or sc 751: 29). (also refer to last number redial on page 2-951 .).
Page 1279: Resident System Program
Univerge sv8100 issue 11.0 resident system program 2 - 1247 resident system program description when power is supplied to the system, the hardware configuration is scanned and resident system program default values are assigned including terminal types (e.G. Pgd(2)-u10 adp, dss console). This enable...
Page 1280
Issue 11.0 univerge sv8100 2 - 1248 resident system program related features none guide to feature programming none operation none.
Page 1281: Reverse Voice Over
Univerge sv8100 issue 11.0 reverse voice over 2 - 1249 reverse voice over description during a call, reverse voice over lets a busy multiline terminal user make a private intercom call to an idle co-worker. The idle co-worker can be at a multiline terminal or single line telephone. The busy user jus...
Page 1282
Issue 11.0 univerge sv8100 2 - 1250 reverse voice over reverse voice over requires a uniquely programmed function key. If an extension user places a reverse voice over to a busy destination extension, the system sets up a voice over. The voice over continues until the reverse voice over key is press...
Page 1283
Univerge sv8100 issue 11.0 reverse voice over 2 - 1251 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 1284
Issue 11.0 univerge sv8100 2 - 1252 reverse voice over to receive a reverse voice over call while busy: 1. Press the voice over key (program 15-07 or sc 751: 48). The voice over key allows you to switch back and forth between the initial call and the reverse voice over call. To return to your initia...
Page 1285: Ring Groups
Univerge sv8100 issue 11.0 ring groups 2 - 1253 ring groups description ring groups determine how trunks ring extensions. Generally, trunks ring extensions only if ring group programming allows. For example, to make a trunk ring an extension: assign the trunk and the extension to the same ring group...
Page 1286
Issue 11.0 univerge sv8100 2 - 1254 ring groups related features automatic call distribution (acd) automatic route selection direct inward line (dil) direct inward dialing (did) direct inward system access (disa) isdn compatibility night service programmable function keys guide to feature programmin...
Page 1287
Univerge sv8100 issue 11.0 ring groups 2 - 1255 22-01-04 system options for incoming calls – dil no answer recall time a dil that rings its programmed destination longer than this time diverts to the dil no answer ring group (set in program 22-08). 0~64800 (seconds) (default = 0) 22-02-01 incoming c...
Page 1288
Issue 11.0 univerge sv8100 2 - 1256 ring groups use the charts below to program the following example: 22-08-01 dil/irg no answer destination for dil delayed ringing, assign the dil no answer ring group. An unanswered dil rings this group after the dil no answer time (program 22-01-04) expires. Dil ...
Page 1289
Univerge sv8100 issue 11.0 ring groups 2 - 1257 operation refer to central office calls, answering on page 2-261 . Program 22-04 : incoming extension ring group assignment ring group 1 > 1 2 3 trunk 1 x - - trunk 2 - x - trunk 3 - - x x = trunk assigned to indicated ring group 1 make the same progra...
Page 1290
Issue 11.0 univerge sv8100 2 - 1258 ring groups this page intentionally left blank.
Page 1291
Univerge sv8100 issue 11.0 ringdown extension, internal/external 2 - 1259 ringdown extension, internal/external description with a ringdown extension, a user can call another extension, outside number, or speed dialing number by lifting the handset. The call automatically goes through – there is no ...
Page 1292
Issue 11.0 univerge sv8100 2 - 1260 ringdown extension, internal/external use the @ code to make an outbound call automatically forward to a disa trunk or to vm auto attendant. This code can be used only on isdn outbound calls. Internal calls and analog outbound calls are not supported. Default sett...
Page 1293
Univerge sv8100 issue 11.0 ringdown extension, internal/external 2 - 1261 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro ...
Page 1294
Issue 11.0 univerge sv8100 2 - 1262 ringdown extension, internal/external operation to place a call if your extension has ringdown programmed: 1. Lift the handset. If you want to place a trunk call, press a line key before lifting the handset. Depending on the setting of your ringdown timer, you may...
Page 1295: Room Monitor
Univerge sv8100 issue 11.0 room monitor 2 - 1263 room monitor description room monitor lets an extension user listen to the sounds in a co-workers area. For example, the receptionist could listen for sounds in the warehouse when it is left unattended. To use room monitor, the initiating extension an...
Page 1296
Issue 11.0 univerge sv8100 2 - 1264 room monitor call arrival (car) key (virtual extension) keys do not support room monitor programmable function keys (code 39). Room monitor for single line telephones can be used with the hotel/motel feature. For a multiline terminal, room monitor requires uniquel...
Page 1297
Univerge sv8100 issue 11.0 room monitor 2 - 1265 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progr...
Page 1298
Issue 11.0 univerge sv8100 2 - 1266 room monitor multiline room monitoring.
Page 1299
Univerge sv8100 issue 11.0 room monitor 2 - 1267 operation you must activate room monitor at the extension initiating the monitor and at the extension you want to monitor. You can only listen to one extension at a time. Multiline terminals: to activate room monitor from an idle multiline terminal (i...
Page 1300
Issue 11.0 univerge sv8100 2 - 1268 room monitor 2. Dial the number of extension you want to monitor. You can place and answer other calls while room monitor is active. To activate room monitor from an idle multiline terminal (extension to be monitored): 1. Press room monitor key (program 15-07 or s...
Page 1301: Save Number Dialed
Save number dialed 2 - 1269 s save number dialed description save number dialed allows an extension user to save their last outside number dialed and easily redial it later on. For example, an extension user can recall a busy or unanswered number without manually dialing the digits. The system retai...
Page 1302
Issue 11.0 univerge sv8100 2 - 1270 save number dialed related features automatic route selection central office calls, placing dial tone detection last number redial programmable function keys repeat redial guide to feature programming the level 1, level 2 and level 3 columns indicate the programs ...
Page 1303
Univerge sv8100 issue 11.0 save number dialed 2 - 1271 operation to save the outside number you just dialed (up to 24 digits): use this feature before hanging up. Multiline terminal 1. Press the save number dialed key (program 15-07 or sc 751: 30). Single line telephone 1. Hookflash. 2. Dial 715. To...
Page 1304
Issue 11.0 univerge sv8100 2 - 1272 save number dialed to view the number you have saved from a multiline terminal with a display: 1. Press the save number dialed key (program 15-07 or sc 751: 30). The stored number displays for 10 seconds. The stored number dials out if you: lift the handset, press...
Page 1305: Secondary Incoming Extension
Univerge sv8100 issue 11.0 secondary incoming extension 2 - 1273 secondary incoming extension description secondary incoming extensions (sies) are incoming appearance keys of actual stations assigned in the system. Sie keys are assigned to programmable function keys and can appear on an individual s...
Page 1306
Issue 11.0 univerge sv8100 2 - 1274 secondary incoming extension in version 3000 or higher software, the system can be programmed to blink the page number of a dt300/dt700 desi-less terminal when it receives an incoming call, or switch to the page of the incoming call. Also, a default page can be de...
Page 1307
Univerge sv8100 issue 11.0 secondary incoming extension 2 - 1275 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards f...
Page 1308
Issue 11.0 univerge sv8100 2 - 1276 secondary incoming extension 15-02-30 multiline telephone basic data setup – toll restriction class select the toll restriction class used when placing a call from a virtual extension. 0 = vir. Ext. (virtual extension class) 1 = real ext. (real extension class) (d...
Page 1309
Univerge sv8100 issue 11.0 secondary incoming extension 2 - 1277 15-18-02 virtual extension key enhanced options – display mode when placing a call on virtual extension key define whether calls to or from a virtual extension key display the virtual extension key name or the name of the extension on ...
Page 1310
Issue 11.0 univerge sv8100 2 - 1278 secondary incoming extension operation to answer a call ringing a sie key: 1. Press the flashing sie key. To program a sie key on a phone: 1. Press speaker. 2. Dial 752. 3. Press the key you want to program. 4. Dial 03. 5. Dial the number of the extension you want...
Page 1311: Secretary Call (Buzzer)
Univerge sv8100 issue 11.0 secretary call (buzzer) 2 - 1279 secretary call (buzzer) description secretary call lets two co-workers alert each other without disturbing their work. To have secretary call, both co-workers must have multiline terminals with secretary call buzzer keys. When a user presse...
Page 1312
Issue 11.0 univerge sv8100 2 - 1280 secretary call (buzzer) related features programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels a...
Page 1313
Univerge sv8100 issue 11.0 secretary call (buzzer) 2 - 1281 to check to see who left you a secretary call: 1. Do not lift the handset. 2. Press the help key. 3. Press the secretary call key that flashed. 4. Press the exit key. To answer your secretary call indication: 1. Place an intercom call to th...
Page 1314
Issue 11.0 univerge sv8100 2 - 1282 secretary call (buzzer) this page intentionally left blank.
Page 1315: Secretary Call Pickup
Univerge sv8100 issue 11.0 secretary call pickup 2 - 1283 secretary call pickup description secretary call pickup lets a multiline terminal user easily reroute calls intended for a co-worker to themselves. By pressing a secretary call pickup key, the user can have all calls to a co-worker’s telephon...
Page 1316
Issue 11.0 univerge sv8100 2 - 1284 secretary call pickup related features call forwarding with follow me programmable function keys secretary call (buzzer) single line telephones, analog 500/2500 sets guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that a...
Page 1317
Univerge sv8100 issue 11.0 secretary call pickup 2 - 1285 to cancel secretary call pickup: 1. Press your lit secretary call pickup key (program 15-07 or sc 751: 42 + boss extension). To check a key secretary call pickup assignment: 1. Press the help key. 2. Press your secretary call arrival (car) ke...
Page 1318
Issue 11.0 univerge sv8100 2 - 1286 secretary call pickup this page intentionally left blank.
Page 1319: Security
Univerge sv8100 issue 11.0 security 2 - 1287 security description this system supports the following built-in simple security features: warning message (watch mode) automatically and periodically send the watching (vrs) message from built-in speaker on multiline terminal or external paging adapter d...
Page 1320
Issue 11.0 univerge sv8100 2 - 1288 security watch mode can be started and stopped manually using service code (program 11-12-63) or function key (sc752: 32) assignment. After 10 seconds a warning message is provided, press again to stop the message. Security sensor can be started and stopped automa...
Page 1321
Univerge sv8100 issue 11.0 security 2 - 1289 when an emergency call is answered: provide a vrs message to the destination. After finishing the vrs message, start monitor operation which pre-programmed in program 20-46-10. Also by pressing key from outside, it is possible to enable a two-way path. If...
Page 1322
Issue 11.0 univerge sv8100 2 - 1290 security if multiple sensors are detected at the same time, the latest detected sensor’s warning message is provided. The warning message continues to play the same vrs message. To cancel the warning message use security sensor reset service code program 11-12-62....
Page 1323
Univerge sv8100 issue 11.0 security 2 - 1291 press exit, terminal returns to idle display. Remote inspection to use the remote inspection feature target destination setting is necessary. When remote inspection is set to the terminal, confirm and ring time are displayed on multiline terminal lcd. If ...
Page 1324
Issue 11.0 univerge sv8100 2 - 1292 security when the target destination answered: provide a vrs message to the destination. After finishing vrs message, destination person can start monitoring of inspection terminal. Also by dialing from outside it is possible to make both way talk. Dialing during ...
Page 1325
Univerge sv8100 issue 11.0 security 2 - 1293 if the vrs message is not recorded, a tone is provided. Emergency call destination must be set considering this feature’s purpose. The emergency number dialed does not follow ars settings: if program 13-01-01 is set to trunk the system uses command progra...
Page 1326
Issue 11.0 univerge sv8100 2 - 1294 security default setting none system availability terminals all multiline terminals required component(s) cd-8dlca/ cd-16dlca pz-vm21 with cf pgdad version 7000 enhancement license (0036) related features paging, external speed dial – system/group/station voice re...
Page 1327
Univerge sv8100 issue 11.0 security 2 - 1295 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmi...
Page 1328
Issue 11.0 univerge sv8100 2 - 1296 security 13-04-01 speed dialing number and name – speed dialing data enter the system and group speed dialing numbers and names. 1~9, 0, , # pause (press line key 1) recall/flash (press line key 2) @ = code to wait for answer supervision in isdn (press line key 3...
Page 1329
Univerge sv8100 issue 11.0 security 2 - 1297 20-44-02 watch mode setup – external paging group for watch message define external paging group number for watching message. 0 = no external paging 1-8 = external paging group number (default = 0) 20-44-03 watch mode setup – vrs message for watch mode de...
Page 1330
Issue 11.0 univerge sv8100 2 - 1298 security 20-45-09 remote watch setup – interval of auto dial assign interval between auto dial when making emergency call. Terminal no. 1-6: 0 = no call 1-3600 (seconds) (default = 0) 20-46-01 security sensor setup – sensor mode define to use security sensor. Secu...
Page 1331
Univerge sv8100 issue 11.0 security 2 - 1299 20-46-08 security sensor setup – repeat dial times define repeat numbers for making emergency call. Security sensor no. 1-8 0 = no redial 1-255 (times) (default = 0) 20-46-09 security sensor setup – auto dial calling time define calling continue time when...
Page 1332
Issue 11.0 univerge sv8100 2 - 1300 security operation warning message (watch mode): program 11-10-20: (616) record, erase vrs message sc616 program 11-10-46: (614) watch message setting program 11-12-63: (717+1/0) watch mode start/stop program 15-07-01: set 32 to function key program 20-44-01: (1) ...
Page 1333
Univerge sv8100 issue 11.0 security 2 - 1301 set up watch mode 1. Press speaker and dial 614. 2. Dial the internal paging group number 01. 3. Dial the external paging group number 1. 4. Dial the interval time of watch message 05. 5. Dial the vrs message number being watched 001. 6. After the beep, r...
Page 1334
Issue 11.0 univerge sv8100 2 - 1302 security program 20-46-01: (1) sensor mode, on program 20-46-02: (1) internal paging group, 1 program 20-46-03: (1) external paging group, 1 program 20-46-04: (1) vrs message number for warning, 1 program 20-46-05: (1999) speed dial bin number, 1999 program 20-46-...
Page 1335
Univerge sv8100 issue 11.0 security 2 - 1303 start security operation 1. Press speaker and dial 719 + 1. The sensor is enabled using the timer in program 20-55-01. -or- 2. Press function key ( 33), the function keys turn red. The key lights after the timer in program 20-55-01 expires. The sensor is ...
Page 1336
Issue 11.0 univerge sv8100 2 - 1304 security remote inspection program 11-10-49: (619) auto dial setting for remote program 20-45-01: (200) remote inspection terminal, 200 program 20-45-02: (12:00) ringing start time, 12 o’clock noon program 20-45-03: (3) ringing continue time, 3 minutes program 20-...
Page 1337
Univerge sv8100 issue 11.0 security 2 - 1305 answering the remote inspection ring 1. At 12:00 o’clock (noon) extension 200 will start ringing. 2. The first vrs message is played when answered. 3. When message finishes, the call disconnects. Not answering the remote inspection ring 1. At 12:00 o’cloc...
Page 1338
Issue 11.0 univerge sv8100 2 - 1306 security security report program 10-20-01 (index 12): 20000 program 90-20-11: 1 in the above settings, use the sensor mode or remote inspection emergency call, to record a traffic report..
Page 1339: Selectable Display Messaging
Univerge sv8100 issue 11.0 selectable display messaging 2 - 1307 selectable display messaging description an extension user can select a programmed selectable display message for their extension. Display multiline terminal callers see the selected message when they call the user’s extension. Selecta...
Page 1340
Issue 11.0 univerge sv8100 2 - 1308 selectable display messaging conditions the # cannot be used in a message. When selectable display messaging is set as dnd all, all other dnd modes are canceled when selectable display messaging is canceled. The selectable display message will not display to the c...
Page 1341
Univerge sv8100 issue 11.0 selectable display messaging 2 - 1309 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards f...
Page 1342
Issue 11.0 univerge sv8100 2 - 1310 selectable display messaging 20-02-07 system options for multiline telephones – time and date display mode set the system time and date display mode. The time that displays in selectable display messages follows this setting. 1~8 type 1 = (12 hour) 10 mar tue 3:15...
Page 1343
Univerge sv8100 issue 11.0 selectable display messaging 2 - 1311 operation to select a message: 1. Press speaker + press the text message key (program 15-07 or sc 751: 18) + enter digits to append (if needed) + speaker to hang up. Skip the remaining steps. 2. (optional for messages 1~8 and 10.) dial...
Page 1344
Issue 11.0 univerge sv8100 2 - 1312 selectable display messaging 3. Press speaker to hang up. Intercom calls to extensions with selectable display messaging set receive a dnd signal and receive the display message on their telephone display instead of ringing the extension based on the setting in pr...
Page 1345: Selectable Ring Tones
Univerge sv8100 issue 11.0 selectable ring tones 2 - 1313 selectable ring tones description an extension user can change the way trunks or internal calls ring their telephone. Selectable ring tones allow an extension user to set up unique ringing for their calls. This is important in a crowded work ...
Page 1346
Issue 11.0 univerge sv8100 2 - 1314 selectable ring tones related features distinctive ringing, tones and flash patterns guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly use...
Page 1347
Univerge sv8100 issue 11.0 selectable ring tones 2 - 1315 operation to change your extension incoming ring tones: 1. Press speaker. 15-08-01 incoming virtual extension ring tone setup when an extension or a virtual extension is assigned to the function key on the key telephone, select the ring tone ...
Page 1348
Issue 11.0 univerge sv8100 2 - 1316 selectable ring tones 2. Dial 720. 3. Dial 1 to set intercom ring; 2 to set trunk ring. 4. Dial code for the desired ring pattern (1~8). 5. Press speaker to hang up. To listen to the incoming ring choices: 1. Press idle speaker. 2. Dial 711. 3. Dial 1 to listen to...
Page 1349: Serial Call
Univerge sv8100 issue 11.0 serial call 2 - 1317 serial call description serial call transfers a call so it automatically returns to the transferring extension. Serial calling saves transferring steps between users. For example, a customer service representative (csr) has a client on the telephone wh...
Page 1350
Issue 11.0 univerge sv8100 2 - 1318 serial call related features programmable function keys transfer guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are ...
Page 1351
Univerge sv8100 issue 11.0 serial call 2 - 1319 operation to place a serial call to a co-worker: 1. Place or answer a call. 2. Press hold or transfer. 3. Dial co-worker’s extension number. Co-worker must lift the handset to respond to your announcement. 4. Press the serial call key (program 15-07 or...
Page 1352
Issue 11.0 univerge sv8100 2 - 1320 serial call this page intentionally left blank.
Page 1353
Univerge sv8100 issue 11.0 single line telephones, analog 500/2500 sets 2 - 1321 single line telephones, analog 500/2500 sets description the system is compatible with 500 type (dial pulse) and 2500 type (dtmf) analog single line telephones (slts). You can install single line telephones as on-premis...
Page 1354
Issue 11.0 univerge sv8100 2 - 1322 single line telephones, analog 500/2500 sets the cd-cp00-us has 32 resources for dtmf receiving and dial tone detection. When a pz-bs10 is installed there are 64 resources available. When program 10-09-01 is set to 0 (common) and program 14-02-10 (caller id) is se...
Page 1355
Univerge sv8100 issue 11.0 single line telephones, analog 500/2500 sets 2 - 1323 related features single line telephone users have access to the following features: data communications apa and apr modules can be used with multiline terminals to provide an analog port. Refer to the individual feature...
Page 1356
Issue 11.0 univerge sv8100 2 - 1324 single line telephones, analog 500/2500 sets guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and ...
Page 1357
Univerge sv8100 issue 11.0 single line telephones, analog 500/2500 sets 2 - 1325 10-09-01 dtmf and dial tone circuit setup if the system has 2500 type (dtmf) single line extensions, allocate at least one circuit for analog extension dtmf reception (0 or 1). Use the following as a guide when allocati...
Page 1358
Issue 11.0 univerge sv8100 2 - 1326 single line telephones, analog 500/2500 sets 15-03-06 single line telephone basic data setup – extension polarity reverse -- not used in u.S. -- do not change default entry as dtmf issues may arise with voice mail. 0 = disable (off) 1 = enable (on) (default = 0) 1...
Page 1359
Univerge sv8100 issue 11.0 single line telephones, analog 500/2500 sets 2 - 1327 20-03-03 system options for single line telephones – slt dtmf dial to trunk lines set the slt phones to (0). Collect all digits before sending or (1), send out immediately after receiving. When using a third-party exter...
Page 1360
Issue 11.0 univerge sv8100 2 - 1328 single line telephones, analog 500/2500 sets 80-03-01 dtmf tone receiver setup – detect level use items 11~32 to set the criteria for dial tone detection for outgoing ars calls. 0 = 0dbm ~ -25dbm 1 = -5dbm ~ -30dbm 2 = -10dbm ~ -35dbm 3 = -15dbm ~ -40dbm 4 = -20db...
Page 1361
Univerge sv8100 issue 11.0 single line telephones, analog 500/2500 sets 2 - 1329 80-03-03 dtmf tone receiver setup – min. Detect level define the minimum detection level for dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20d...
Page 1362
Issue 11.0 univerge sv8100 2 - 1330 single line telephones, analog 500/2500 sets 80-03-04 dtmf tone receiver setup – max. Detect level define the maximum detection level for dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(...
Page 1363
Univerge sv8100 issue 11.0 single line telephones, analog 500/2500 sets 2 - 1331 80-03-05 dtmf tone receiver setup – forward twist level define the forward twist level for dtmf tone receiver. 0~9 (1db~10db) default: type 1 = 5 (6dbm) type 2 = 5 (6dbm) type 3 = 5 (6dbm) type 4 = 5 (6dbm) type 5 = 5 (...
Page 1364
Issue 11.0 univerge sv8100 2 - 1332 single line telephones, analog 500/2500 sets operation refer to the individual features listed in the related features section above in this feature. 80-04-04 call progress tone detector setup – no tone time set no tone time. 0~255 (30+30-7680ms) the formula is 30...
Page 1365: Slt Adapter
Univerge sv8100 issue 11.0 slt adapter 2 - 1333 slt adapter description the slt (single line telephone) adapter allows a port of a cd-8dlca, pz-8dlcb, cd-16dlca or cd-lta to support a single line telephone. A single line telephone can be connected to the dlc port using the slt adapter and 2-wire cab...
Page 1366
Issue 11.0 univerge sv8100 2 - 1334 slt adapter cordless telephone connection single line telephones, analog 500/2500 sets guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly u...
Page 1367
Univerge sv8100 issue 11.0 slt adapter 2 - 1335 11-02-01 extension numbering assign extension numbers to extension ports. Up to eight digits 1 101 2 102 3 103 ~ ~ 99 199 100 3101 ~ ~ 512 3513 20-07-01 class of service options (administrator level) – manual night service enabled turn off or on an ext...
Page 1368
Issue 11.0 univerge sv8100 2 - 1336 slt adapter 20-07-12 class of service options (administrator level) – trunk port disable turn off or on an extension user ability to use the trunk port disable feature. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for cos 15) 20-07-13 class of service op...
Page 1369
Univerge sv8100 issue 11.0 slt adapter 2 - 1337 20-07-24 class of service options (administrator level) – set/ cancel private call refuse enable/disable an extension user ability to set or cancel private call refuse. 0 = disable 1 = enable (default = 0 for cos 1~15) 20-07-25 class of service options...
Page 1370
Issue 11.0 univerge sv8100 2 - 1338 slt adapter 20-08-08 class of service options (outgoing call service) – toll restriction dial block turn off or on an extension user ability to use dial block. 0 = off 1 = on (default = 0 for cos 1~15) 20-08-09 class of service options (outgoing call service) – ho...
Page 1371
Univerge sv8100 issue 11.0 slt adapter 2 - 1339 20-08-17 class of service options (outgoing call service) – ars override of trunk access map turn off or on an extension user ability to override the trunk access map programming for outgoing calls. 0 = off 1 = on (default = 0 for cos 1~15) 20-08-19 cl...
Page 1372
Issue 11.0 univerge sv8100 2 - 1340 slt adapter 20-09-05 class of service options (incoming call service) – signal/ voice call turn off or on an extension user ability to enable handsfree answerback or forced intercom ringing for their incoming intercom calls. 0 = off 1 = on (default = 1 for cos 1~1...
Page 1373
Univerge sv8100 issue 11.0 slt adapter 2 - 1341 20-10-08 class of service options (answer service) – virtual extension off-hook answer turn off or on an extension user ability to answer an incoming call on a call arrival (car)/secondary incoming extension (sie)/ virtual extension simply by lifting t...
Page 1374
Issue 11.0 univerge sv8100 2 - 1342 slt adapter 20-11-08 class of service options (hold/ transfer service) – transfer information display turn off or on an extension incoming transfer pre-answer display. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-09 class of service options (hold/ transfer serv...
Page 1375
Univerge sv8100 issue 11.0 slt adapter 2 - 1343 20-11-18 class of service options (hold/ transfer service) – no recall no recall set to 1 does not stop transferred calls from recalling from a virtual extension. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-19 class of service options (hold/ transf...
Page 1376
Issue 11.0 univerge sv8100 2 - 1344 slt adapter 20-13-01 class of service options (supplementary service) – long conversation alarm turn off or on the warning tone for long conversation (not for single line telephones). 0 = off 1 = on (default = 0 for cos 1~15) 20-13-02 class of service options (sup...
Page 1377
Univerge sv8100 issue 11.0 slt adapter 2 - 1345 20-13-12 class of service options (supplementary service) – room monitor, extension being monitored turn off or on an extension user ability to be monitored by other extensions. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-13 class of service option...
Page 1378
Issue 11.0 univerge sv8100 2 - 1346 slt adapter 20-13-22 class of service options (supplementary service) – busy status display (called party status) turn off or on the ability to display the detailed state of the called party. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-23 class of service opti...
Page 1379
Univerge sv8100 issue 11.0 slt adapter 2 - 1347 20-13-33 class of service options (supplementary service) – acd supervisor’s position enhancement set this option to on for the operator to use service codes in program 11-13-10 through program 11-13-13. 0 = off 1 = on (default = 0 for cos 1~15) 20-13-...
Page 1380
Issue 11.0 univerge sv8100 2 - 1348 slt adapter 20-13-45 class of service options (supplementary service) – mic key mode while call monitoring set per class of service, when in call monitoring mode determines if the monitored parties receives the barge in alert tone when coaching mode is enabled. 0 ...
Page 1381
Univerge sv8100 issue 11.0 slt adapter 2 - 1349 operation to originate internal calls: 1. Lift the handset, and wait for internal dial tone. 2. Dial the applicable internal number. 20-14-05 class of service options for disa/e&m – operator calling enable/disable a disa or tie trunk caller ability to ...
Page 1382
Issue 11.0 univerge sv8100 2 - 1350 slt adapter 3. Talk when called party answers. To originate outside calls: 1. Lift the handset, and wait for dial tone. 2. Dial trunk access code (default: 9). 3. Dial the number of outside party. 4. Talk when the called party answers. To answer outside or interna...
Page 1383
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1351 smb8000 communications analyst description smb8000 communications analyst is an easy to use, graphically oriented software package that allows you to monitor and analyze telephone calls, understand telephone usage, and cut costs. Inc...
Page 1384
Issue 11.0 univerge sv8100 2 - 1352 smb8000 communications analyst highlights of smb8000 communications analyst: network based. Callalert! This module can generate alarms by email, pager screen, screen pop-up, or .Wav file. When it detects user defined patterns in the call records. Automatic report ...
Page 1385
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1353 the following software items are installed on the pc: multi-site process manager (mspm) to collect call records from the system. Smb8000 communications analyst to allow reports and other communications analyst features. Sql express 2...
Page 1386
Issue 11.0 univerge sv8100 2 - 1354 smb8000 communications analyst if the collate option is enabled in the communications analyst multi-site configuration, all legs of a call are combined into one call record. Also, the communications analyst will not release the call from the database until the tru...
Page 1387
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1355 operating systems supported: windows xp professional with sp 2, windows 2003 server with sp 2, windows vista business edition or windows 7 (32-bit). Software supported: database server: ms sql server 2005\ms sql server express 2005\m...
Page 1388
Issue 11.0 univerge sv8100 2 - 1356 smb8000 communications analyst e911 compatibility isdn compatibility multiple trunk types station message detail recording t1 trunking (with ani/dnis compatibility) traffic reports trunk groups guide to feature programming the level 1, level 2 and level 3 columns ...
Page 1389
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1357 35-01-02 smdr options – output destination number specify the smdr printer output extension (cta extension number). Up to eight digits (default not assigned) 35-01-03 smdr options – header language specify the language used to print ...
Page 1390
Issue 11.0 univerge sv8100 2 - 1358 smb8000 communications analyst 35-02-05 smdr output options – summary (weekly) set this option to 1 to have the smdr report provide a weekly summary (every saturday at midnight). 0 = not displayed 1 = displayed (default = 1) 35-02-06 smdr output options – summary ...
Page 1391
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1359 35-02-16 smdr output options – trunk name or received dialed number determine how the smdr should print incoming calls on ani/dnis or did trunks. If set to 1, ani/dnis trunks can print dnis digits. For did trunks, if the received num...
Page 1392
Issue 11.0 univerge sv8100 2 - 1360 smb8000 communications analyst lan connection: for additional smdr programming options, see station message detail recording on page 2-1413 . Programming notes: if the system is programmed to display the date (program 35-02-14=1), the date is displayed regardless ...
Page 1393
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1361 for proper handling of dnis calls, the name field (program 22-11-03) must be the same as the received dnis digits (program 22-11-01 and program 35-02-12 did table name must be turned on). If this is not set, smb8000 communications an...
Page 1394
Issue 11.0 univerge sv8100 2 - 1362 smb8000 communications analyst smb8000 e911 security notification description the smb8000 e911 security notification (esn) application suite, an easy-to- use yet powerful e911 notification solution. The e911 security notification solution offers robust features de...
Page 1395
Univerge sv8100 issue 11.0 smb8000 communications analyst 2 - 1363 propagating the changes made using the administration console to the esn alert clients will require the admin.Ini file to be shared for the clients to access them over a network. The licence.Lic file from the smb8000 communications a...
Page 1396
Issue 11.0 univerge sv8100 2 - 1364 smb8000 communications analyst guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards...
Page 1397: Smb8000 Conference Bridge
Univerge sv8100 issue 11.0 smb8000 conference bridge 2 - 1365 smb8000 conference bridge description the cd-pvaa is a conference bridge that is used in the univerge sv8100. This etu can be licensed to support a 8- or 16-port conference bridge. The smb8000 conference bridge is configured using an inte...
Page 1398
Issue 11.0 univerge sv8100 2 - 1366 smb8000 conference bridge one customized greeting can be recorded for the smb8000 conference bridge application. Http interface for conference schedule management and conference blade administration. Remote conference programming with conference scheduler (via a w...
Page 1399
Univerge sv8100 issue 11.0 smb8000 conference bridge 2 - 1367 telephone dial pad help utilizing dtmf digits conference organizer can make a call out and invite a participant by pressing 01# on the telephone dial pad. Lock and unlock the conference by pressing 02#on the telephone dial pad. Mute and u...
Page 1400
Issue 11.0 univerge sv8100 2 - 1368 smb8000 conference bridge the cd-pvaa blade with smb8000 conference bridge application can be used with version 1.11 or higher software on the univerge sv8100 system. The support pc must be connected directly to the cd-pvaa smb8000 conference bridge and not connec...
Page 1401
Univerge sv8100 issue 11.0 smb8000 conference bridge 2 - 1369 a comparison between preset and scheduled mode is shown below: for sv8100 systems with version 4000 or higher system software and has been migrated from a ux5000, table 2-76 migration supported blades defines the application blades suppor...
Page 1402
Issue 11.0 univerge sv8100 2 - 1370 smb8000 conference bridge system availability terminals all multiline terminals required component(s) cd-pvaa aks conference bridge application (compact flash media) related features none.
Page 1403
Univerge sv8100 issue 11.0 smb8000 conference bridge 2 - 1371 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for ...
Page 1404
Issue 11.0 univerge sv8100 2 - 1372 smb8000 conference bridge 10-54-02 license configuration for each package – license quantity assign the number of licenses to the conference application per slot. For the slot the cd-pvaa blade is installed in, assign the number of licensed conference bridge ports...
Page 1405
Univerge sv8100 issue 11.0 smb8000 conference bridge 2 - 1373 10-55-04 package network setup – sub net mask define the subnet mask for the cd-etia. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 ...
Page 1406
Issue 11.0 univerge sv8100 2 - 1374 smb8000 conference bridge 11-07-01 department group pilot numbers – dial assign a department group pilot number for the cd-pvaa (eight digits max). The extensions are assigned to the group in program 16-02-01. Up to eight digits (default not assigned) 15-03-01 sin...
Page 1407
Univerge sv8100 issue 11.0 smb8000 conference bridge 2 - 1375 16-01-05 department group basic data setup – extension group all ring mode operation set whether all members of the group should ring automatically or manually using the service code defined in program 11-12-09. When set to 1, only icm an...
Page 1408
Issue 11.0 univerge sv8100 2 - 1376 smb8000 conference bridge operation refer to the smb8000 conference bridge installation manual. 22-02-01 incoming call trunk setup assign service type 4 to each trunk you want to ring into the multimedia conference bridge as a direct inward line (dil). Trunks 1~20...
Page 1409: Softkeys
Univerge sv8100 issue 11.0 softkeys 2 - 1377 softkeys description each display telephone provides interactive softkeys for intuitive feature access. It is not necessary to remember feature codes to access the telephone advanced features because the function of the softkeys change as the user process...
Page 1410
Issue 11.0 univerge sv8100 2 - 1378 softkeys system availability terminals all multiline terminals required component(s) none related features directory dialing volume controls guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programm...
Page 1411
Univerge sv8100 issue 11.0 softkeys 2 - 1379 operation none 15-02-01 multiline telephone basic data setup – display language selection (to select options 8~10, press either 8 or recall, then press line keys 1~3. Key 1 is option 8, key 2 is option 9, and key 3 is option 10.) set the display language ...
Page 1412
Issue 11.0 univerge sv8100 2 - 1380 softkeys this page intentionally left blank.
Page 1413
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1381 speed dial – system/group/station description speed dialing gives an extension user quick access to frequently called numbers. This saves time, for example, when calling a client with whom they deal often. Instead of dialing a lon...
Page 1414
Issue 11.0 univerge sv8100 2 - 1382 speed dial – system/group/station dss console chaining dss console chaining allows an extension user with a dss console to chain to a speed dialing number stored under a dss console key. The stored number dials out (chains) to the initial call. This can, for examp...
Page 1415
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1383 conditions speed dial bins can contain stored account codes. To prevent them from being displayed use program 20-07-04. Ars selects the trunk for the call unless the user preselects. A user can implement speed dial only if their e...
Page 1416
Issue 11.0 univerge sv8100 2 - 1384 speed dial – system/group/station if program 13-01-01 is set to 1 (intercom access mode), system speed dial bins require inserting a trunk access code. When operating the right cursor key, if the menu is not enabled by programming or there are no numbers in a tele...
Page 1417
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1385 single line telephones, analog 500/2500 sets trunk group routing guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are mos...
Page 1418
Issue 11.0 univerge sv8100 2 - 1386 speed dial – system/group/station 11-12-11 service code setup (for service access) – group speed dialing customize the service code used for group speed dialing. Mlt, slt (default = # 4) 13-01-01 speed dialing option setup – speed dialing auto outgoing call mode d...
Page 1419
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1387 13-04-04 speed dialing number and name – transfer destination number when the incoming caller id matches the number programmed in the speed dial bin, this setting determines the destination of the call. If transfer mode is (refer ...
Page 1420
Issue 11.0 univerge sv8100 2 - 1388 speed dial – system/group/station 15-07-01 programmable function keys assign a function key for system speed dialing (27) or group speed dialing (28). You can program the key as either a general speed dialing key or you can choose to store a bin number with the fu...
Page 1421
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1389 30-03-01 dss console key assignment for dss console chaining, assign an speed dialing service code (or) plus a 2-digit bin number to a dss console key. Key number 001~500 0~99 (general functional level) 97 = door box access key (a...
Page 1422
Issue 11.0 univerge sv8100 2 - 1390 speed dial – system/group/station 80-03-03 dtmf tone receiver setup – min. Detect level define the minimum detect levels for the dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20dbm(0) to ...
Page 1423
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1391 80-03-04 dtmf tone receiver setup – max. Detect level define the maximum detect levels for the dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(0) to – 2...
Page 1424
Issue 11.0 univerge sv8100 2 - 1392 speed dial – system/group/station 80-03-05 dtmf tone receiver setup – forward twist level define the forward twist levels for the dtmf tone receiver. 0~9 (1db~10db) [default: type 1~5 = 5 (6dbm)] 80-03-06 dtmf tone receiver setup – backward twist level define the ...
Page 1425
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1393 80-04-03 call progress tone detector setup – s/n ratio define the s/n ratio for the call progress tone detector. 0~4 (0db ~ -20db) default: type 1 (dt) – 4 (-20db) type 2 (bt) – 4 (-20db) type 3 (rbt) – 4 (-20db) type 4, type 5 – ...
Page 1426
Issue 11.0 univerge sv8100 2 - 1394 speed dial – system/group/station operation to store an speed dialing number (display telephones only): 1. Press speaker. 2. Dial 753 (for system) or 754 (for group). 3. Dial system or group storage code. Initially, there are 1000 system speed dialing codes. There...
Page 1427
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1395 5. Press hold. 6. Enter the name associated with the speed dialing number. 7. Press hold. 8. Press speaker to hang up or repeat steps 3~7 to program another system or group speed dial bin. Table 2-77 keys for entering names use th...
Page 1428
Issue 11.0 univerge sv8100 2 - 1396 speed dial – system/group/station to dial a system speed dialing number: 1. Go off-hook. 2. Press redial. - or - press the right cursor key until the group speed dial menu appears. 3. Dial the system speed dialing storage code. Unless you preselect, trunk group ro...
Page 1429
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1397 3. Dial the group speed dialing code. The stored number dials out. Unless you preselect, trunk group routing selects the trunk for the call. If you have a dss console, you may be able to press a dss console key to chain to a store...
Page 1430
Issue 11.0 univerge sv8100 2 - 1398 speed dial – system/group/station 6. Enter the name associated with the speed dialing number (display telephones only). 7. Press hold. 8. Press speaker to hang up. To store a station speed dialing number (single line telephones only): 1. Lift the handset. 2. Dial ...
Page 1431
Univerge sv8100 issue 11.0 speed dial – system/group/station 2 - 1399 3. Dial the station speed dial buffer number to be programmed (0~9). 1 = station speed dial buffer 1 2 = station speed dial buffer 2 3 = station speed dial buffer 3 4 = station speed dial buffer 4 5 = station speed dial buffer 5 6...
Page 1432
Issue 11.0 univerge sv8100 2 - 1400 speed dial – system/group/station 3. Dial the speed dial memory location. Station speed dial 0~9 group speed dial xxx (none at default) system speed dial 000~999 4. Converse..
Page 1433
Univerge sv8100 issue 11.0 speed dial – telephone book 2 - 1401 speed dial – telephone book description speed dial – telephone book is a part of the speed dialing system. A maximum of 100 telephone books are supported per system. Individual extensions can be assigned up to two telephone books. Each ...
Page 1434
Issue 11.0 univerge sv8100 2 - 1402 speed dial – telephone book required component(s) none related features speed dial – system/group/station guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they ...
Page 1435
Univerge sv8100 issue 11.0 speed dial – telephone book 2 - 1403 13-07-01 telephone book dial number and name – speed dialing data assign telephone numbers to entries in each book. There are 100 books with 300 hundred entries (0-299) in each book. Maximum 24 digits 1~9, 0, , # , pause (press line ke...
Page 1436
Issue 11.0 univerge sv8100 2 - 1404 speed dial – telephone book operation to search for an entry in the telephone book: 1. Press the dir softkey. 2. Press the telbk softkey. 3. Press the softkey associated with the first or second book. - or - press the right cursor key. 13-10-01 telephone book rout...
Page 1437
Univerge sv8100 issue 11.0 speed dial – telephone book 2 - 1405 4. After selecting the book, choose one of the following search types. To scroll the entries in the book, press up or down on the cursor pad. Once you reach the last entry on the page, the display advances to the next page. To select on...
Page 1438
Issue 11.0 univerge sv8100 2 - 1406 speed dial – telephone book 7. If you want to change the telephone book entry name, type the new name using the telephone dial pad keys and press the center button on the cursor pad. To accept the name change, press the center button on the cursor pad again. If yo...
Page 1439
Univerge sv8100 issue 11.0 speed dial – telephone book 2 - 1407 3. Press the softkey associated with the first or second book. - or - press the right cursor key. 4. Search to select the telephone name, telephone number or registry entry (0~299) to change. 5. Press the dial softkey to dial the select...
Page 1440
Issue 11.0 univerge sv8100 2 - 1408 speed dial – telephone book this page intentionally left blank.
Page 1441: Station Hunt
Univerge sv8100 issue 11.0 station hunt 2 - 1409 station hunt description after calling a busy extension, a call immediately hunts to the next available member of the hunt group (department group). The caller does not have to hang up and place another intercom call if the first extension called is u...
Page 1442
Issue 11.0 univerge sv8100 2 - 1410 station hunt guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progr...
Page 1443
Univerge sv8100 issue 11.0 station hunt 2 - 1411 operation to make a step call: 1. Place a call to a busy extension..
Page 1444
Issue 11.0 univerge sv8100 2 - 1412 station hunt this page intentionally left blank.
Page 1445
Univerge sv8100 issue 11.0 station message detail recording 2 - 1413 station message detail recording description station message detail recording (smdr) provides a record of both system trunk calls and internal calls. Typically, the record outputs to a customer-provided printer, terminal or smdr da...
Page 1446
Issue 11.0 univerge sv8100 2 - 1414 station message detail recording data call tracking data call tracking can log the system internal data calls. Since smdr normally logs external (trunk) data calls, data call tracking lets you get a complete picture of data terminal activity. Digit counting with d...
Page 1447
Univerge sv8100 issue 11.0 station message detail recording 2 - 1415 (the lan port only provides information through lan-capable programs, such as hyperterminal. Printing of the smdr information must be done from that program.) internal smdr provides: answered calls smdr records the calling extensio...
Page 1448
Issue 11.0 univerge sv8100 2 - 1416 station message detail recording answering paging smdr records the extension that originated the page and the extension that answers using meet me paging. Group call smdr records the extension that answered the department call. Ccis smdr does not support internal ...
Page 1449
Univerge sv8100 issue 11.0 station message detail recording 2 - 1417 if program 35-02-18 = 1 (caller id name output method) is set to line feed, the smdr displays as follows: sample smdr report (internal) class time date line duration station dialled no./cli account pot 10:52 12/09 002 00:00:10 2001...
Page 1450
Issue 11.0 univerge sv8100 2 - 1418 station message detail recording table 2-78 smdr report definitions report headings definitions call record number smdr record number (consecutive) class type of call (see class definitions below) time time call placed or answered. (for transferred calls, shows ti...
Page 1451
Univerge sv8100 issue 11.0 station message detail recording 2 - 1419 table 2-79 smdr report format with program 35-02-14 set to ‘0’ character position field definition header line 1 1~60 spaces 61~70 mm/dd/yyyy 71 space 72~75 page 76 space 77~79 report page number (e.G., 001) cr & lf carriage return...
Page 1452
Issue 11.0 univerge sv8100 2 - 1420 station message detail recording 5 space 6~10 time in 24 hour clock (hh:mm) 11 space 12~21 line 22 space 23~30 call duration (hh:mm:ss) 31 space 32~41 station number or name 42 space 43~62 number dialed (20 digits maximum) 63 space 64~79 account number or no answe...
Page 1453
Univerge sv8100 issue 11.0 station message detail recording 2 - 1421 12~15 date 16~17 spaces 18~21 line 22 space 23~30 duration 31~32 spaces 33~39 station 40~44 spaces 45~51 dialled 52 space 53~59 no./cli 60~63 spaces 64~70 account cr & lf carriage return and line feed lf line feed smdr record 1~4 c...
Page 1454
Issue 11.0 univerge sv8100 2 - 1422 station message detail recording conditions smdr data does not include internal calls version 6000 (v6.02 or lower). With version 7000 or higher software, smdr can record/print both system trunk and internal calls. Version 7000 enhancement license (0036) and smdr ...
Page 1455
Univerge sv8100 issue 11.0 station message detail recording 2 - 1423 with version 8000 or higher software and the pz-me50-us installed, the sv8100 can buffer up to 4000 calls. The version 8000 enhancement license (0037) and smdr feature license (0008) is required. When smdr reports are enabled using...
Page 1456
Issue 11.0 univerge sv8100 2 - 1424 station message detail recording when the connection is active, the smdr information will be immediately output and it will not be buffered. When the system is powered off, all current records in the buffer are deleted. When the buffer fills, the oldest record rem...
Page 1457
Univerge sv8100 issue 11.0 station message detail recording 2 - 1425 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizar...
Page 1458
Issue 11.0 univerge sv8100 2 - 1426 station message detail recording 14-01-06 basic trunk data setup – smdr printout have the system print or not print the trunk you are programming in the smdr printout. Refer to programs 35-01 and 35-02 for smdr printout options. 0 = no print out 1 = prints out (de...
Page 1459
Univerge sv8100 issue 11.0 station message detail recording 2 - 1427 20-07-19 class of service options (administrator level) – smdr printout department group (stg) data determine if department group (stg) data is included in the smdr report for each cos. 0 = off 1 = on (default = 0 for cos 1~14) (de...
Page 1460
Issue 11.0 univerge sv8100 2 - 1428 station message detail recording 35-01-07 smdr options – minimum ring time (for incoming calls) a call must ring for at least this time to be included on the smdr report. Enter 0 to allow all calls to print. 0~65535 (seconds) (0 = all) (default = 0) 35-01-08 smdr ...
Page 1461
Univerge sv8100 issue 11.0 station message detail recording 2 - 1429 35-02-08 smdr output options – incoming call enable this option (1) to have the smdr report include incoming calls. If you disable this option (0), incoming calls do not print. 0 = not displayed 1 = displayed (default = 1) 35-02-09...
Page 1462
Issue 11.0 univerge sv8100 2 - 1430 station message detail recording 35-02-17 smdr output options – print account code or caller name of incoming call determine whether the account code or caller id name should print in the smdr record. Program 35-01-08 must be set to 0 for this entry to be followed...
Page 1463
Univerge sv8100 issue 11.0 station message detail recording 2 - 1431 35-04-01 smdr port assignment for department groups assign the smdr port for each department group. For each department group, select the smdr port to which the outgoing smdr information should be sent. Department groups: 1~64 smdr...
Page 1464
Issue 11.0 univerge sv8100 2 - 1432 station message detail recording smdr flowcharts are located on the following pages. Smdr with a cd-cp00-us ethernet or serial connection via ct(a)-r adapter on a dth/dtr terminal.
Page 1465
Univerge sv8100 issue 11.0 station message detail recording 2 - 1433 smdr flowchart.
Page 1466
Issue 11.0 univerge sv8100 2 - 1434 station message detail recording smdr flowchart (continued).
Page 1467
Univerge sv8100 issue 11.0 station message detail recording 2 - 1435 smdr flowchart (continued).
Page 1468
Issue 11.0 univerge sv8100 2 - 1436 station message detail recording operation once installed and programmed, smdr operation is automatic. Smdr flowchart (continued).
Page 1469
Univerge sv8100 issue 11.0 station name assignment – user programmable 2 - 1437 station name assignment – user programmable description this feature allows a user to program the station name for their telephone extension or any extension in the system. The name is displayed on the multiline terminal...
Page 1470
Issue 11.0 univerge sv8100 2 - 1438 station name assignment – user programmable guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and w...
Page 1471
Univerge sv8100 issue 11.0 station name assignment – user programmable 2 - 1439 operation to program your extension name: 1. Press speaker. 2. Dial 700. - or - press the extension name change key (program 15-07 or sc 751: 55). 3. Press hold. 4. Enter the name. (refer to table 2-72 selectable display...
Page 1472
Issue 11.0 univerge sv8100 2 - 1440 station name assignment – user programmable 6 enter characters: m-o, m-o, 6. 7 enter characters: p-s, p-s, 7. 8 enter characters: t-v, t-v, 8. 9 enter characters: w-z, w-z, 9. 0 enter characters: 0 ! “ # $ % & ’ ( ) ô Õ ú å ä ö ü enter characters: + , - . / : ; ? ...
Page 1473: Station Relocation
Univerge sv8100 issue 11.0 station relocation 2 - 1441 station relocation description station relocation allows a station to be moved from one location to another, without having to reprogram the station data. The station features and extension number are the same after it is moved to the new locati...
Page 1474
Issue 11.0 univerge sv8100 2 - 1442 station relocation default setting none system availability terminals all multiline terminals and single line telephones required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs th...
Page 1475
Univerge sv8100 issue 11.0 station relocation 2 - 1443 the following programs are swapped when station relocation is used: program 11-02 extension numbering program 12-05 night mode group assignment for extensions program 13-03 speed dialing group assignment for extensions program 15-01 basic extens...
Page 1476
Issue 11.0 univerge sv8100 2 - 1444 station relocation program 21-15 individual trunk group routing for extensions program 21-19 ip trunk (sip) calling party number setup for extension program 23-02 call pickup groups program 23-03 universal answer/auto answer program 23-04 ringing line preference f...
Page 1477: Sv8100 Internal Router
Univerge sv8100 issue 11.0 sv8100 internal router 2 - 1445 sv8100 internal router description the sv8100 internal router converged network appliance is an intelligent, all-in-one networking solution for enterprises and service providers. It reduces costs by simplifying the deployment, management, an...
Page 1478
Issue 11.0 univerge sv8100 2 - 1446 sv8100 internal router voip resolves nat/fw traversal problems for sip, mgcp and h.323 traffic, and allows a single public ip address to be used for multiple voip clients. Voip survivability is also provided so that local sip pstn gateways are available for inboun...
Page 1479
Univerge sv8100 issue 11.0 sv8100 internal router 2 - 1447 default setting none system availability terminals ip multiline station (sip) ip single line station (sip) required component(s) sv8100 internal router blade cd-rtb related features none guide to feature programming system programming is not...
Page 1480
Issue 11.0 univerge sv8100 2 - 1448 sv8100 internal router operation reference edgemar internal router board manual. Operating procedures depend on the application..
Page 1481: Sv8100 Netlink
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1449 sv8100 netlink description the netlink feature allows up to 16 sites to be linked together over a data communication ip netlink that allows remote sites to have the same service features as the main site, acting as one system. Systems can be install...
Page 1482
Issue 11.0 univerge sv8100 2 - 1450 sv8100 netlink conditions with version 4000 or higher software, systems using netlink no longer refer to programs 10-46-06 sip registrar port and 10-46-13 subscribe session port. New programs 51-17-01 and 51-17-02 are used to change the ports on a per system basis...
Page 1483
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1451 when fail-over occurs, the primary system is changed to another communication server. The ip applications do not know the new primary ip address, so the following features are disabled after fail-over: smdr acd-mis sip terminal soft phone ip k-ccis ...
Page 1484
Issue 11.0 univerge sv8100 2 - 1452 sv8100 netlink for a network to be suitable for voip it must pass specific requirements. To ensure the site meets these requirements, an ip ready check and a site survey must be completed at each site before voip implementation. One-way delay must not exceed 100ms...
Page 1485
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1453 the following programs require a reset after making a change using pcpro, webpro or handset programming: with version 4000 software, the failover process in a netlink environment is improved. When network communication is down, an alarm is sent to t...
Page 1486
Issue 11.0 univerge sv8100 2 - 1454 sv8100 netlink restrictions all ip trunks must be connected to the primary system, version 4000 (v4.01 or lower). The number of total ports depends on the primary system. System id (program 51-01-02) must be unique for each system in a netlink network. Acd/mis can...
Page 1487
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1455 when the secondary netlink system calls out using its own sip trunk, no dsps are used from the primary system. The netlink nodes which have their own sip trunks can use register ids independently of each other. A secondary netlink system is able to ...
Page 1488
Issue 11.0 univerge sv8100 2 - 1456 sv8100 netlink conditions main software version 5000 or higher and the version 5.00 main version license (0034) are required to support the netlink multi-sip carrier feature. It is possible to set register id for trunks that belong to that specific system. For exa...
Page 1489
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1457 required component(s) cd-cp00-us blade with pz-32/64/128ipla or pz-32/64/128iplb and pz-me50-us daughter boards lk-sys-netlinkx-lic related features automatic route selection guide to feature programming the level 1, level 2 and level 3 columns indi...
Page 1490
Issue 11.0 univerge sv8100 2 - 1458 sv8100 netlink 10-12-10 cd-cp00-us network setup – subnet mask define the media gateway subnet mask address. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 255...
Page 1491
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1459 51-01-03 netlink system property setting – secondary system flag if set to 0, netlink is dynamically established based on node list in program 51-03-01. Primary system is selected in the order the system wakes up. If set to 1, the system connects wi...
Page 1492
Issue 11.0 univerge sv8100 2 - 1460 sv8100 netlink 51-03-01 netlink internet protocol address list setting – internet protocol address list the system seeks the primary system based on this list. When there is no primary system yet, or fail over occurs, node list is referred to establish new link. T...
Page 1493
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1461 51-05-07 netlink timer settings – socket refresh time if the ip connection becomes unstable, the keep-alive function does not work. To avoid this, if there is no data traffic for this time, the socket is refreshed. 20~3600 (seconds) (default = 40) 5...
Page 1494
Issue 11.0 univerge sv8100 2 - 1462 sv8100 netlink 51-09-02 netlink communication port settings – communication waiting port set the port used to communicate between nodes. It is always opened by all nodes. 0~65535 (default = 58001) 51-09-03 netlink communication port settings – secondary communicat...
Page 1495
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1463 51-12-01 primary system information – system id for reference only. (default = 0) 51-12-02 primary system information – system name for reference only. (default not assigned) 51-12-03 primary system information – ip address for reference only. (defa...
Page 1496
Issue 11.0 univerge sv8100 2 - 1464 sv8100 netlink 51-16-01 netlink system data replication mode setting – system data replication mode set the synchronous mode of the system data. When set to 1 , the systems are synchronized at the time set in item 02 below. When set to 2, the systems are synchroni...
Page 1497
Univerge sv8100 issue 11.0 sv8100 netlink 2 - 1465 operation none 84-26-01 ipl basic setup – ip address assign the ip address for each dsp on the ipla. Xxx.Xxx.Xxx.Xxx defaults: slot 1 = 172.16.0.20 : slot 4 = 172.16.0.44 voip gw number 1~8 172.16.0.20~ 172.16.16.0.27 84-26-02 ipl basic setup – rtp ...
Page 1498
Issue 11.0 univerge sv8100 2 - 1466 sv8100 netlink this page intentionally left blank.
Page 1499: Sv8100 Poe Gigabit Switch
Univerge sv8100 issue 11.0 sv8100 poe gigabit switch 2 - 1467 sv8100 poe gigabit switch description the nec poe gigabit switch (gswu) is a fully managed switch which brings gigabit speeds to users while adding a whole new level of intelligence and security to networks. The eight 10/100/1000 mbps por...
Page 1500
Issue 11.0 univerge sv8100 2 - 1468 sv8100 poe gigabit switch vlan port based and 802.1q tag-based vlans management vlan automatic configuration of vlans across multiple switches through gvrp/ garp auto mdi/mdix port mirroring traffic on a port can be mirrored to another port for analysis with a net...
Page 1501
Univerge sv8100 issue 11.0 sv8100 poe gigabit switch 2 - 1469 the ip address for the gswu will be assigned in program program 10-55 on the sv8100. It contains settings for ip address, subnet mask and a gateway ip address. Stacking formation when a gswu determines that it is an “add-on” by the config...
Page 1502
Issue 11.0 univerge sv8100 2 - 1470 sv8100 poe gigabit switch default setting none system availability terminals none required components cd-etia related features none table 2-86 migration supported blades blade color chs1u-us blue 19” chassis chs2u b-us blue 9.5” base chassis chs2u e blue 9.5” exp ...
Page 1503
Univerge sv8100 issue 11.0 sv8100 poe gigabit switch 2 - 1471 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for ...
Page 1504
Issue 11.0 univerge sv8100 2 - 1472 sv8100 poe gigabit switch 10-55-04 package network setup – sub net mask define the subnet mask for the cd-etia. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 ...
Page 1505
Univerge sv8100 issue 11.0 sv8100 poe gigabit switch 2 - 1473 operation none.
Page 1506
Issue 11.0 univerge sv8100 2 - 1474 sv8100 poe gigabit switch this page intentionally left blank.
Page 1507
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1475 sv8100 uc desktop suite applications enhancements uc desktop applications version 2.0.0.0 or higher with main cpu software version 2000 or higher provides the following enhancements: support for the callto hyperlink within micr...
Page 1508
Issue 11.0 univerge sv8100 2 - 1476 sv8100 uc desktop suite applications uc desktop applications version 3.6.0.0 or higher supports: microsoft windows 7 (32- and 64-bit platforms). Parked calls can be monitored in the active call list. With version 4000 or higher software, soai and 3rd party cti can...
Page 1509
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1477 description the sv8100 uc desktop suite applications allows users to control their sv8100 terminal from their pc (deskset mode) or the pc can become their sv8100 terminal (sp310 - ip soft phone mode). Through licensing control ...
Page 1510
Issue 11.0 univerge sv8100 2 - 1478 sv8100 uc desktop suite applications with uc desktop applications version 3.5.0.0 or higher, the outlook integration is enhanced to include the ability to associate a presence state with an outlook calendar appointment, and to add telephone numbers from an outlook...
Page 1511
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1479 desktop client the desktop client enhances the operation of the nec digital telephone set by providing easy access to common, and not so common, univerge sv8100 voice control features. This software application provides a very ...
Page 1512
Issue 11.0 univerge sv8100 2 - 1480 sv8100 uc desktop suite applications softphone the sp310 softphone is a software phone that functions as an ip multiline station (sip). The sp310 provides access to all features of a physical ip multiline station with a few exceptions. Through the voip connection ...
Page 1513
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1481 inmail integration can be set to on in the desktop configuration wizard on the voicemail tab in preferences. Desktop shared services the sv8100 desktop application includes the option to install desktop shared services that are...
Page 1514
Issue 11.0 univerge sv8100 2 - 1482 sv8100 uc desktop suite applications centralized blf monitoring – the desktop shared services monitors the status of all stations on the system and provides updates to the individual clients. With uc desktop application version 4.0 or higher, the blf status area c...
Page 1515
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1483 active call list screen pop shortcuts dialing rules telephony settings voice mail notification settings quick message phone message trunk settings phone image only selected settings in the following preferences tabs are saved i...
Page 1516
Issue 11.0 univerge sv8100 2 - 1484 sv8100 uc desktop suite applications instant messenger – with desktop version 5.0.0.0 or higher, when using shared services desktop users can instant message each other. A maximum of eight im sessions can be established with different users. Uc desktop suite has t...
Page 1517
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1485 multiple logon with version 3000 or higher software, the same user name and password can be assigned to multiple extensions when using automatic or manual registration. This makes it easier on the user by only having to remembe...
Page 1518
Issue 11.0 univerge sv8100 2 - 1486 sv8100 uc desktop suite applications conditions uc desktop suite does not support the cordless dtl-8r-1 terminal. The uc desktop application must be running in order to run the answering center. The uc desktop application does not support centrex trunks for transf...
Page 1519
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1487 uc desktop application users cannot dial digits while a call is in progress. If the desktop user presses the disconnect button to abort a transfer, the call shows up in desktop as a held call. The desktop user is not automatica...
Page 1520
Issue 11.0 univerge sv8100 2 - 1488 sv8100 uc desktop suite applications blf indication for another station is solid green or flashing green if the blf is for the station the application is running. There is no difference between busy or ringing for a blf of another station. If dnd and cfa are set f...
Page 1521
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1489 the enhancement bundle features require a non-deskset only license level even when controlling a deskset phone. When a non-deskset only license level is selected, the desktop registers as an ip station consuming an additional s...
Page 1522
Issue 11.0 univerge sv8100 2 - 1490 sv8100 uc desktop suite applications in systems that have migrated from the ux5000 to the sv8100 and utilize ux5000 phones, program 20-02-23 must be set to 1 (ux5000 special operation mode), and program 20-23-05 must be set to 1 (on). The synchronization button wi...
Page 1523
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1491 50mb available disk space cd rom drive network adapter sound card ada-l for recording/personal greeting in deskset mode windows server 2003 sp2, windows xp sp2, windows vista business 32-bit and windows 7 professional 32-bit an...
Page 1524
Issue 11.0 univerge sv8100 2 - 1492 sv8100 uc desktop suite applications guide to feature programming the level 1, level 2 and level 2 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro w...
Page 1525
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1493 10-12-10 cd-cp00-us network setup – subnet mask define the media gateway subnet mask address. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.2...
Page 1526
Issue 11.0 univerge sv8100 2 - 1494 sv8100 uc desktop suite applications 10-20-01 lan setup for external equipment – tcp port define the tcp port number for the lan cti and o&m communication between the cd-cp00-us and the uc desktop applications. 0~65535 default: external device 1 (cti server) = 0 e...
Page 1527
Univerge sv8100 issue 11.0 sv8100 uc desktop suite applications 2 - 1495 15-07-01 programmable function keys assign a function key to terminals. Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 20-02-23 system options for multi...
Page 1528
Issue 11.0 univerge sv8100 2 - 1496 sv8100 uc desktop suite applications in addition to the above programming, define the programming options as required for the system features. Refer to the univerge sv8100 programming manual for programming details.Callback, callback request, and auto redial are n...
Page 1529: Sv8100/sv8300 Terminals
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1497 sv8100/sv8300 terminals description the sv8100/sv8300 is a full-featured ip based communications system providing a rich feature set with pure voice over ip (voip) communications, across corporate local and wide area networks (lan and wan)....
Page 1530
Issue 11.0 univerge sv8100 2 - 1498 sv8100/sv8300 terminals sv8100 supports aes 128 bit encryption. Program 10-46-08 mode1 (read only) represents aes 128 bit. Conditions in version 3000 or higher software the system can be programmed to blink the page number of a dt300/dt700 desi-less terminal when ...
Page 1531
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1499 dt300/dt700 terminals installed in a sv8100 with the ipk/ipk ii migration system do not support the desi-less page switching and blinking. Desi-less screen page switching only applies to idle terminals. If a terminal is not idle, the screen...
Page 1532
Issue 11.0 univerge sv8100 2 - 1500 sv8100/sv8300 terminals dt 700 series ip terminals dt 710 (economy) itl-2-( ) itl-6d-( ) itl-8lde-( ) economical terminal providing access to basic telephony and messaging service fully functional keypad providing standard business functions such as hold, transfer...
Page 1533
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1501 table 2-92 terminal category reference chart (d term series i terminals) provides a quick reference of the series i terminals. Table 2-92 terminal category reference chart (d term series i terminals) series name equipment id system compatib...
Page 1534
Issue 11.0 univerge sv8100 2 - 1502 sv8100/sv8300 terminals table 2-93 connectivity of options provides a quick overview of the options available with the dt300/dt700 series telephones. Table 2-93 connectivity of options terminal options ip terminals digital terminals sophisticated itl-320c-1 tel va...
Page 1535
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1503 table 2-94 terminal and adapter compatibility shows the compatibility between the terminals and adapter used in the system. Table 2-94 terminal and adapter compatibility terminal adapter unit ada-l apr-l ilpa psa-l bch-l bha-l gba-l ipv6-l ...
Page 1536
Issue 11.0 univerge sv8100 2 - 1504 sv8100/sv8300 terminals table 2-95 dt330 compatibility settings ada-l unit switch settings terminal lot number dt-330 xxx i lx or lower (version 1.E0 or lower) xxx i mx (version 8.10) xxxjsx or higher (version 2.20 or higher) ada connection for recording only. Dip...
Page 1537
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1505 table 2-97 terminal and line key/lcd compatibility shows the compatibility between the terminals and line key or lcd used in the system. Table 2-97 terminal and line key/lcd compatibility terminal line key/lcd 8 lk-l 8lkd(ld)-l 8lki(ld)-l 1...
Page 1538
Issue 11.0 univerge sv8100 2 - 1506 sv8100/sv8300 terminals table 2-98 terminal and ten key kit compatibility shows the compatibility between the terminals and ten key kits used in the system. Table 2-98 terminal and ten key kit compatibility terminal ten key kit bs(f)-l bs(s)-l bs (braille)-l (bk) ...
Page 1539
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1507 table 2-99 adapter compatibility shows the compatibility between the adapters used in the system. Encryption encryption must be turned on in the dt700 as well as the sv8100 for encryption to take place. Encryption is supported between the d...
Page 1540
Issue 11.0 univerge sv8100 2 - 1508 sv8100/sv8300 terminals table 2-100 ipla dsp usage codec baseline with srtp 32voip db g.711 32 32 g.722 32 24 g.726 32 24 g.729ab 32 24 g.723.1 24 16 ilbc 24 16 t38 32 28 64voip db g.711 64 64 g.722 64 48 g.726 64 48 g.729ab 64 48 g.723.1 48 32 ilbc 48 32 g3 fax 6...
Page 1541
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1509 table 2-101 iplb dsp usage codec baseline with srtp 32voip db g.711 32 32 g.722 32 32 g.726 32 32 g.729ab 32 32 g.723.1 32 32 ilbc 32 32 t.38 udpl 32 32 t.38 rtp 32 32 64voip db g.711 64 64 g.722 64 64 g.726 64 64 g.729ab 64 64 g.723.1 64 6...
Page 1542
Issue 11.0 univerge sv8100 2 - 1510 sv8100/sv8300 terminals default setting none system availability terminals none required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this fea...
Page 1543
Univerge sv8100 issue 11.0 sv8100/sv8300 terminals 2 - 1511 10-46-08 dt700 server information setup – encryption type read only 10-46-09 dt700 server information setup – one time password set the one-time password for encryption authentication to the dt700. Up to 10 characters (0~9, , # ) (default =...
Page 1544
Issue 11.0 univerge sv8100 2 - 1512 sv8100/sv8300 terminals operation refer to individual features..
Page 1545: Synchronous Ringing
Univerge sv8100 issue 11.0 synchronous ringing 2 - 1513 synchronous ringing description synchronous ringing synchronizes co/pbx incoming ringing with the incoming ringing pattern from a central office. Conditions when the multiline terminal is ringing at secondary extension (se)/virtual extension (v...
Page 1546
Issue 11.0 univerge sv8100 2 - 1514 synchronous ringing guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featur...
Page 1547
Univerge sv8100 issue 11.0 synchronous ringing 2 - 1515 operation none 22-03-01 trunk ring tone range – ring tone pattern assign ring tone ranges to trunks. Trunks ring extensions according to the ring tone range selected in program 22-03-0 and the settings made with either service code 720 or progr...
Page 1548
Issue 11.0 univerge sv8100 2 - 1516 synchronous ringing this page intentionally left blank.
Page 1549
T1 trunking (with ani/dnis compatibility) 2 - 1517 t t1 trunking (with ani/dnis compatibility) description the t1/pri interface gives the system t1 trunking ability. This blade uses a single universal slot and provides up to 24 trunk circuits. In additional to providing digital-quality trunking, the...
Page 1550
Issue 11.0 univerge sv8100 2 - 1518 t1 trunking (with ani/dnis compatibility) flexible routing based on the data received, the system can route the incoming ani/dnis call to: an extension an acd or voice mail master extension number a vrs and play a vrs message to the caller a department group pilot...
Page 1551
Univerge sv8100 issue 11.0 t1 trunking (with ani/dnis compatibility) 2 - 1519 smdr can print trunk port names or received dialed number for ani/dnis or did trunks. If enabled in programming, dnis digits can be printed on the smdr reports instead of the trunk name. T1 trunks follow tie line toll rest...
Page 1552
Issue 11.0 univerge sv8100 2 - 1520 t1 trunking (with ani/dnis compatibility) required software none related features caller id central office calls, answering central office calls, placing code restriction dial tone detection direct inward dialing (did) isdn compatibility station message detail rec...
Page 1553
Univerge sv8100 issue 11.0 t1 trunking (with ani/dnis compatibility) 2 - 1521 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and web...
Page 1554
Issue 11.0 univerge sv8100 2 - 1522 t1 trunking (with ani/dnis compatibility) 10-03-06 etu setup (dti (t1) pkg setup) – number of ports set up and confirm the basic configuration data for the number of ports required. 0 = auto 1 = 4 ports 2 = 8 ports 3 = 12 ports 4 = 16 ports 5 = 20 ports (default =...
Page 1555
Univerge sv8100 issue 11.0 t1 trunking (with ani/dnis compatibility) 2 - 1523 14-02-01 analog trunk data setup – signaling type (dp/dtmf) for ani/dnis, the following additional settings in program 14-02 are recommended: item 1: signaling type (dp/ dtmf) = 2 (dtmf) item 2: ring detect type = 1 (immed...
Page 1556
Issue 11.0 univerge sv8100 2 - 1524 t1 trunking (with ani/dnis compatibility) 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m override turn off or on an extension ability to receive a second call from a did, disa, dil, or tie line caller. With this optio...
Page 1557
Univerge sv8100 issue 11.0 t1 trunking (with ani/dnis compatibility) 2 - 1525 20-14-07 class of service options for disa/e&m – external paging enable/disable a disa or tie trunk caller ability to use telephone system external paging. 0 = off 1 = on (default = 1 for cos 1~15) 20-14-08 class of servic...
Page 1558
Issue 11.0 univerge sv8100 2 - 1526 t1 trunking (with ani/dnis compatibility) 22-11-03 did translation number conversion – did name for each did translation table entry (1~2000), specify the name that should show on the dialed extension display when it rings. Maximum 12 digits (default not assigned)...
Page 1559
Univerge sv8100 issue 11.0 t1 trunking (with ani/dnis compatibility) 2 - 1527 34-09-02 ani/dnis service options – delimiter dial code define the character telco uses as a delimiter (see entries 1~5 in program 34-09-01). Valid entries are: 0~9, # , and . 1~9, 0, , # (default = for cos 1~15) 34-09...
Page 1560
Issue 11.0 univerge sv8100 2 - 1528 t1 trunking (with ani/dnis compatibility) 34-09-06 ani/dnis service options – routing spd table setup define which part of the spd dial table set up in program 13-04 the system uses for ani/dnis caller id look-ups and ani/dnis routing (start = 0, 100~1900, end = 0...
Page 1561
Univerge sv8100 issue 11.0 t1 trunking (with ani/dnis compatibility) 2 - 1529 operation refer to the operation for the following features: central office calls, answering central office calls, placing direct inward dialing (did) tie lines.
Page 1562
Issue 11.0 univerge sv8100 2 - 1530 t1 trunking (with ani/dnis compatibility) this page intentionally left blank.
Page 1563: Tandem Ringing
Univerge sv8100 issue 11.0 tandem ringing 2 - 1531 tandem ringing description tandem ringing allows an extension user to have two telephones with one telephone number. For example, extension 105 (the master telephone) sets tandem ringing with extension 106. When extension 105 receives an incoming ca...
Page 1564
Issue 11.0 univerge sv8100 2 - 1532 tandem ringing tandem ringing is not supported with extensions defined as operator extensions in program 20-17-01. Default setting disabled system availability terminals master telephone: tdm multiline terminals or single line telephones slave telephone: single li...
Page 1565
Univerge sv8100 issue 11.0 tandem ringing 2 - 1533 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pro...
Page 1566
Issue 11.0 univerge sv8100 2 - 1534 tandem ringing 4. Enter the extension number to be considered the slave telephone (the telephone that rings when the master extension rings). A confirmation tone is heard (if speaker was used). 5. Press speaker to hang up (if the key is lit). While the feature is ...
Page 1567
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1535 tandem trunking (unsupervised conference) description tandem trunking allows an extension user to join two outside callers in a trunk-to-trunk conference. The extension user can then drop out of the call, leaving the trunk...
Page 1568
Issue 11.0 univerge sv8100 2 - 1536 tandem trunking (unsupervised conference) method d - automatic tandem trunking setup to speed dial number this method allows an extension user to easily set up an unsupervised conference with a call they have placed on hold. A class of service option is available,...
Page 1569
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1537 with an analog trunk, the continue/disconnect code may work using dtmf sounds from the opposite side trunk. With an isdn trunk, program 14-01-25 must be enabled to detect the continue/disconnect code. The continue/disconne...
Page 1570
Issue 11.0 univerge sv8100 2 - 1538 tandem trunking (unsupervised conference) required component(s) none related features call forwarding, off-premise central office calls, answering central office calls, placing direct inward system access (disa) guide to feature programming the level 1, level 2 an...
Page 1571
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1539 14-01-13 basic trunk data setup – trunk- to-trunk transfer for each trunk that should be able to participate in a tandem call, enter 1. 0 = disable 1 = enable (default = 1) 15-07-01 programmable function keys (optional) as...
Page 1572
Issue 11.0 univerge sv8100 2 - 1540 tandem trunking (unsupervised conference) method b – tandem trunking with transfer key: 24-02-07 system options for transfer – trunk-to-trunk transfer release warning tone this timer starts when a trunk begins talking with another trunk (for example: trunk-to-trun...
Page 1573
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1541 15-07-01 programmable function keys assign a function key for transfer (code 06). Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 20-06-01 class of ...
Page 1574
Issue 11.0 univerge sv8100 2 - 1542 tandem trunking (unsupervised conference) method c – tandem trunking on hang up: 24-02-10 system options for transfer – disconnect trunk-to-trunk this timer starts after the trunk-to-trunk warning tone is heard. 0~64800 (seconds) (default = 0) 25-07-07 system time...
Page 1575
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1543 20-11-11 class of service options (hold/ transfer service) – automatic on-hook transfer turn off or on the trunk-to-trunk transfer restriction. If enabled, trunk-to-trunk transfer is not possible. 0 = off 1 = on (default =...
Page 1576
Issue 11.0 univerge sv8100 2 - 1544 tandem trunking (unsupervised conference) method d – tandem trunking to speed dial number: program number program name description/comments assigned data level 1 2 3 11-10-06 service code setup (for system administrator) – setting the automatic transfer for each t...
Page 1577
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1545 13-04-04 speed dialing number and name – transfer destination number store transfer destination number data in the speed dialing areas. If transfer mode is (refer to 13-04-03): 1 = internal dial mode 1~9, 0, , # , p, r, @...
Page 1578
Issue 11.0 univerge sv8100 2 - 1546 tandem trunking (unsupervised conference) 20-07-11 class of service options (administrator level) – forced trunk disconnect (analog trunk only) turn off or on an extension user ability to use forced trunk disconnect. This allows the extension user to disconnect an...
Page 1579
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1547 trunk disconnect continue/disconnect codes: program number program name description/comments assigned data level 1 2 3 14-01-25 basic trunk data setup – continued/discontinued trunk-to-trunk conversation enable/disable the...
Page 1580
Issue 11.0 univerge sv8100 2 - 1548 tandem trunking (unsupervised conference) operation method a – tandem trunking from conference: to set up a tandem call: 1. Place or answer first trunk call. 2. Press conf softkey. 3. Place or answer second trunk call. 4. To set up the tandem call, press conf twic...
Page 1581
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1549 2. Press speaker or hang up. If program 20-13-10 is set to 0, the conference ends and the line keys go out. If program 20-13-10 is set to 1, to manually disconnect the conference, forced trunk disconnect (i.E., press the l...
Page 1582
Issue 11.0 univerge sv8100 2 - 1550 tandem trunking (unsupervised conference) 2. Press hold to place the first trunk call on hold. 3. Place a second trunk call. 4. Hang up. This sets up an unsupervised conference with both outside parties. The line keys for the trunks light solid red. To disconnect ...
Page 1583
Univerge sv8100 issue 11.0 tandem trunking (unsupervised conference) 2 - 1551 to set and change the destination of the automatic tandem trunk call: 1. Dial service code 735 (or the service code set for set destination for automatic trunk-to-trunk transfer). 2. Dial the desired trunk number (trunk nu...
Page 1584
Issue 11.0 univerge sv8100 2 - 1552 tandem trunking (unsupervised conference) this page intentionally left blank.
Page 1585: Tapi Compatibility
Univerge sv8100 issue 11.0 tapi compatibility 2 - 1553 tapi compatibility description the system has telephony applications programming interface (tapi) compatibility that provides: reduced tapi feature set (see the supported tapi commands chart below) caller id data to the pc for data base lookups ...
Page 1586
Issue 11.0 univerge sv8100 2 - 1554 tapi compatibility refer to table 2-102 tapi commands for a list of supported tapi commands. The tapi compatibility feature does not support cap keys 1000~9999. Only 0001~0999 can be supported. With version 4000 or higher software, soai and 3rd party cti can be us...
Page 1587
Univerge sv8100 issue 11.0 tapi compatibility 2 - 1555 soai controlled extensions cannot be used with the mobile extension feature. Aspirenet is not supported when soai and 3rd party tapi are used in the same system. Ccis link reconnect is not supported when soai and 3rd party tapi are used in the s...
Page 1588
Issue 11.0 univerge sv8100 2 - 1556 tapi compatibility guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 1589
Univerge sv8100 issue 11.0 tapi compatibility 2 - 1557 10-12-02 cd-cp00-us network setup – subnet mask the setting of subnet mask is invalid when all host addresses are 0. If the network section is: 0, 127, 128.0, 191.255, 192.0.0, 223.255.255 the setting of subnet mask is invalid. 128.0.0.0 192.0.0...
Page 1590
Issue 11.0 univerge sv8100 2 - 1558 tapi compatibility operation tapi operation is automatic once programmed in the telephone system and enabled in the pc tapi application, unless a headset is used. Using the headset with automatic answer: 1. With the multiline terminal in an idle state, press the h...
Page 1591: Tone Override
Univerge sv8100 issue 11.0 tone override 2 - 1559 tone override description the multiline terminal user that calls a busy station and receives a call waiting tone can generate a tone override that is heard by the originator and busy station. The busy station user can place the existing call on hold ...
Page 1592
Issue 11.0 univerge sv8100 2 - 1560 tone override guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature prog...
Page 1593
Univerge sv8100 issue 11.0 tone override 2 - 1561 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m override turn off or on an extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, the destination ...
Page 1594
Issue 11.0 univerge sv8100 2 - 1562 tone override operation to send off-hook signals to an extension busy on a call: your extension may send off-hook signals automatically. 1. Dial (program11-16-04). - or - dial 709 (program 11-12-02). - or - press the off-hook signaling key (program 15-07-01 code 3...
Page 1595: Traffic Reports
Univerge sv8100 issue 11.0 traffic reports 2 - 1563 traffic reports description the system can send data to a pc connected to the univerge sv8100. The telephone call traffic data for each extension is captured for use with the station message detail recording (smdr) feature. Call traffic the total o...
Page 1596
Issue 11.0 univerge sv8100 2 - 1564 traffic reports system availability terminals all terminals required component(s) software licenses for smdr traffic total report – sample report terminal otg duration cost icm answer duration ringing abandon 301 54 01:45:14 720 326 115 02:11:52 00:09:36 301 92 02...
Page 1597
Univerge sv8100 issue 11.0 traffic reports 2 - 1565 related features station message detail recording guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are...
Page 1598
Issue 11.0 univerge sv8100 2 - 1566 traffic reports this page intentionally left blank.
Page 1599: Transfer
Univerge sv8100 issue 11.0 transfer 2 - 1567 transfer description transfer permits an extension user to send an active intercom or outside call to any other extension in the system. With transfer, any extension user can quickly send a call to the desired co-worker. A call a user transfers, automatic...
Page 1600
Issue 11.0 univerge sv8100 2 - 1568 transfer transfer call into conference/existing call this feature allows either a multiline terminal or single line telephone user with barge-in ability to transfer a call into an existing call. This call can be a 2-party call, a conference call, or a barge-in con...
Page 1601
Univerge sv8100 issue 11.0 transfer 2 - 1569 with transfer to busy extensions enabled (program 24-02-01 = 1), call forwarding with both ringing offers a unique option. A transferred call waits for either the forwarding or destination extension to become free. The call goes through to the extension t...
Page 1602
Issue 11.0 univerge sv8100 2 - 1570 transfer default setting enabled system availability terminals all multiline terminals required component(s) none related features barge-in call waiting/camp-on caller id call forwarding conference meet me paging transfer one-touch calling quick transfer to voice ...
Page 1603
Univerge sv8100 issue 11.0 transfer 2 - 1571 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programmi...
Page 1604
Issue 11.0 univerge sv8100 2 - 1572 transfer 15-07-01 programmable function keys extension users may want a function keys programmed for transfer (code 06). Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 20-02-04 system optio...
Page 1605
Univerge sv8100 issue 11.0 transfer 2 - 1573 20-11-18 class of service options (hold/ transfer service) – no recall no recall set to 1 does not stop transferred calls from recalling from a virtual extension. 0 = off 1 = on (default = 0 for cos 1~15) 20-11-20 class of service options (hold/ transfer ...
Page 1606
Issue 11.0 univerge sv8100 2 - 1574 transfer 21-01-03 system options for outgoing calls – trunk interdigit time (external) the system waits for this time to expire before placing the call in a talk state (call timer starts after time expires, voice over and barge-in are not allowed until after time ...
Page 1607
Univerge sv8100 issue 11.0 transfer 2 - 1575 24-02-02 system options for transfer – moh or ringback on transferred calls enable (0)/disable (1) moh on transfer. If enabled, a transferred caller hears music on hold while their call rings the destination extension. If disabled, a transferred caller he...
Page 1608
Issue 11.0 univerge sv8100 2 - 1576 transfer 25-06-01 vrs/disa one-digit code attendant setup – next attendant message number set up single digit dialing through the vrs. This gives vrs callers single-key access to extensions, the company operator, department calling groups and voice mail. For each ...
Page 1609
Univerge sv8100 issue 11.0 transfer 2 - 1577 operation transferring trunk calls: to transfer a trunk call to a co-worker’s extension: 1. At the multiline terminal, press transfer. - or - at 500/2500 single line telephone, hookflash. You hear transfer dial tone. 2. Dial the co-worker’s extension numb...
Page 1610
Issue 11.0 univerge sv8100 2 - 1578 transfer transferring intercom calls: to transfer your intercom call: 1. At the multiline terminal, press hold. - or - at single line telephone, hookflash. 2. Dial extension to receive your call. If the extension is busy, does not answer or does not want the call,...
Page 1611
Univerge sv8100 issue 11.0 transfer 2 - 1579 3. Hang up. The call is transferred to the trunk ring group defined in program 22-05-01 and all assigned extensions in the group (program 22-04-01) ring or it rings the external paging, enabling anyone to answer the call. Transferring an intercom or trunk...
Page 1612
Issue 11.0 univerge sv8100 2 - 1580 transfer this page intentionally left blank.
Page 1613: Trunk Group Routing
Univerge sv8100 issue 11.0 trunk group routing 2 - 1581 trunk group routing description trunk group routing sets outbound call routing options for users that dial the trunk group routing code (9) for trunk calls. Trunk group routing routes calls in the order specified by system programming. If a use...
Page 1614
Issue 11.0 univerge sv8100 2 - 1582 trunk group routing system availability terminals all terminals required component(s) none related features automatic route selection central office calls, placing direct inward dialing (did) dial tone detection multiple trunk types programmable function keys prim...
Page 1615
Univerge sv8100 issue 11.0 trunk group routing 2 - 1583 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featur...
Page 1616
Issue 11.0 univerge sv8100 2 - 1584 trunk group routing 14-06-01 trunk group routing – priority order number set the priority order number (1~4). 0 = not specify 1~100 : (trunk group number) 1001~1100 : (1000 + route table number) default: route 1, order number 1 = 1 (trunk group 1) order numbers 2,...
Page 1617
Univerge sv8100 issue 11.0 trunk group routing 2 - 1585 15-07-01 programmable function keys assign a function key for trunk group routing access (code 02 + trunk group # ). Line key 1~48 0~99 (normal function code 751 by default) 00 ~ 99 (appearance function code) (service code 752 by default) 21-0...
Page 1618
Issue 11.0 univerge sv8100 2 - 1586 trunk group routing operation to place a call using trunk group routing: 1. At the multiline terminal, press speaker. - or - at single line telephone, lift the handset. 2. Dial 9. 3. Dial number. - or - 1. At the multiline terminal, press trunk group routing key (...
Page 1619: Trunk Groups
Univerge sv8100 issue 11.0 trunk groups 2 - 1587 trunk groups description trunk groups let you optimize trunk usage for incoming and outgoing calls. Each group can be accessed by an access code plus the group number. There are 100 available trunk groups and you set the access order in trunk group pr...
Page 1620
Issue 11.0 univerge sv8100 2 - 1588 trunk groups system availability terminals all terminals required component(s) none related features automatic route selection call appearance (cap) keys central office calls, placing dial tone detection direct inward dialing (did) programmable function keys ring ...
Page 1621
Univerge sv8100 issue 11.0 trunk groups 2 - 1589 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature progr...
Page 1622
Issue 11.0 univerge sv8100 2 - 1590 trunk groups 14-06-01 trunk group routing – priority order number set the priority order number 1~4. 0 = not specify 1~100 : (trunk group number) 1001~1100 : (1000 + route table number) default: route 1, order number 1 = 1 (trunk group 1) order numbers 2, 3, 4 = 0...
Page 1623
Univerge sv8100 issue 11.0 trunk groups 2 - 1591 15-07-01 programmable function keys assign function keys for trunk group access (code 02 + group) or call appearance (cap) keys (code 08 + cap key orbit 0001~9999 (or 0000 for auto assign). Trunk groups: 1~100 line key 1~48 0~99 (normal function cod...
Page 1624
Issue 11.0 univerge sv8100 2 - 1592 trunk groups operation to place a call over a trunk group: 1. At the multiline telephone, press speaker. - or - at the single line telephone, lift the handset. 2. Dial 704. 3. Dial trunk group number (1~9 or 001~100). 4. Dial number. - or - 1. Press the trunk grou...
Page 1625: Trunk Queuing/camp-On
Univerge sv8100 issue 11.0 trunk queuing/camp-on 2 - 1593 trunk queuing/camp-on description trunk queuing permits an extension user to queue (wait in line) on-hook for a busy trunk or trunk group to become free. The system recalls the queued extension as soon as the trunk is available. The user does...
Page 1626
Issue 11.0 univerge sv8100 2 - 1594 trunk queuing/camp-on central office calls, placing programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. The...
Page 1627
Univerge sv8100 issue 11.0 trunk queuing/camp-on 2 - 1595 operation to queue for a busy trunk: 1. Try to access the busy trunk. 2. Dial # or press trunk queuing/camp-on key (program 15-07 or sc 751: 35). 3. Hang up to leave a trunk queuing request. - or - wait off-hook to camp-on to the trunk. To an...
Page 1628
Issue 11.0 univerge sv8100 2 - 1596 trunk queuing/camp-on to cancel a trunk queuing/camp-on request: 1. At the multiline terminal, press idle speaker. - or - at the single line telephone, lift the handset. 2. Dial 770. 3. At the multiline terminal, press speaker to hang up. - or - at the single line...
Page 1629
Ucb (unified communications for business) 2 - 1597 u ucb (unified communications for business) description ucb is a modular multimedia contact center solution providing skills-based routing (sbr) and blending customer contacts using telephone, email, web callback, web chat, voicemail and fax. Ucb pr...
Page 1630
Issue 11.0 univerge sv8100 2 - 1598 ucb (unified communications for business) telephone calls (incoming dit, ana, did, co, or ring transfer) terminate to a programmed queue. Each queue is programmed as a virtual extension so the number of queues depends on the total number of virtual extensions in t...
Page 1631
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1599 the desktop application this application interfaces the agent with the multimedia contact center and provides a real-time indication of contact center activity. Details include the number of calls in queue (including indiv...
Page 1632
Issue 11.0 univerge sv8100 2 - 1600 ucb (unified communications for business) the q-outdial application this application allows significant improvement to agent productivity by blending outbound customer calls with incoming customer contact activity, reducing agent reluctance between calls, and mana...
Page 1633
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1601 between queue progress announcements, the caller is parked and hears the music on hold (moh). When a k-ccis trunk is on hold, the specified line seizure access code is used by the system to retrieve the call from a held st...
Page 1634
Issue 11.0 univerge sv8100 2 - 1602 ucb (unified communications for business) restrictions uc desktop suite does not support the cordless dtl-8r-1 terminal. Ucb is not supported for centralized voice mail. Prior to resetting (powering off and on), the system for any reason, stop the ucb. Restart ucb...
Page 1635
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1603 only one codec can be assigned for sip extensions. Different sip extensions cannot use different codecs. Virtual extensions are supported for queues (agent and operator) and pilot numbers (voice mail, hold, & executive con...
Page 1636
Issue 11.0 univerge sv8100 2 - 1604 ucb (unified communications for business) call transfer to acd queue trunk calls that terminate to a normal station, acd agent, or supervisor can be transferred to an acd queue. Calls must be blind transferred to the queue (the transferring party cannot wait with ...
Page 1637
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1605 the ucb schedule can be programmed per queue to automatically change mode for individual holidays or entire date ranges such as new year holiday, state holidays, and yom kippur. These holidays can be programmed years in ad...
Page 1638
Issue 11.0 univerge sv8100 2 - 1606 ucb (unified communications for business) logon/logoff an agent can log on or off using the q-desktop application. Operating statistics are collected until the agent logs off. Agent hot seating is supported because ucb tracks agent skill profile and statistics aga...
Page 1639
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1607 restrictions: incoming acd queue calls cannot be received when the agent is on break; a queue depth parameter allows calls to deliver through worktime when callers have been waiting longer than the prescribed threshold. Wh...
Page 1640
Issue 11.0 univerge sv8100 2 - 1608 ucb (unified communications for business) voicemail function description user mailboxes are assigned to a mailbox class that defines a maximum number of new, saved, and deleted messages that the mailbox can contain and the number of days before purging each type o...
Page 1641
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1609 4. When nothing is defined there, the system does what is defined in the company mailbox default one-touch keys. Conditions general: to access the ucb voicemail, the caller dials the voice messaging pilot number. Unheard a...
Page 1642
Issue 11.0 univerge sv8100 2 - 1610 ucb (unified communications for business) locally provided keyboard, monitor and mouse will be required for initial setup of the inucb ip address. Locally provided keyboard, monitor and mouse can be used for setup and administration of inucb (os and ucb applicatio...
Page 1643
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1611 phone function name description supported (yes/no) message waiting light yes keys profile yes call voicemail yes voicemail transfer yes redirect to voicemail yes voicemail transfer yes record conversation yes login/logout ...
Page 1644
Issue 11.0 univerge sv8100 2 - 1612 ucb (unified communications for business) presence buttons lcd display cli yes caller name no agent first name yes display mailboxes sharing the phone status no display number of new messages yes 2 display number of urgent messages yes display login state yes disp...
Page 1645
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1613 queues wav editor multimedia queuing modules function name description supported (yes/no) limits system wide maximum (256) display view status of selected monitored extensions yes enter resolution codes through phone yes 1...
Page 1646
Issue 11.0 univerge sv8100 2 - 1614 ucb (unified communications for business) all other modules and applications outdial queuing outbound campaigns no web callback queuing no web chat queuing no function name description supported (yes/no) core client applications user clients: executive desktop, ex...
Page 1647
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1615 default setting none system availability terminals all terminals (except dtu/dtp style terminals) slt, sip dect and third party sip phones can not be agents. Required component(s) local pc for each agent (for desktop appli...
Page 1648
Issue 11.0 univerge sv8100 2 - 1616 ucb (unified communications for business) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and web...
Page 1649
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1617 10-12-02 cd-cp00-us network setup – subnet mask the setting of subnet mask is invalid when all host addresses are 0. If the network section is: 0, 127, 128.0, 191.255, 192.0.0, 223.255.255 the setting of subnet mask is inv...
Page 1650
Issue 11.0 univerge sv8100 2 - 1618 ucb (unified communications for business) 10-12-10 cd-cp00-us network setup – subnet mask define the media gateway subnet mask address. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 ...
Page 1651
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1619 10-20-01 lan setup for external equipment – tcp port define the tcp port (0~65535) when communicating to the cti server (type 1). 0~65535 default: external device 1 (cti server) = 0 external device 2 (acd mis) = 4000 exter...
Page 1652
Issue 11.0 univerge sv8100 2 - 1620 ucb (unified communications for business) 11-07-01 department group pilot numbers – dial assign a department group pilot number for the voice mail (eight digits maximum). The extensions are assigned to the group in program 16-02-01. Up to eight digits (default not...
Page 1653
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1621 16-01-03 department group basic data setup – department routing when busy (auto step call) set how the system routes an intercom call to a busy department group member. The caller can hear busy tone (0) or overflow to the ...
Page 1654
Issue 11.0 univerge sv8100 2 - 1622 ucb (unified communications for business) 20-02-12 system options for multiline telephones – forced intercom ring (icm call type) enable/disable forced intercom ringing. If enabled, incoming intercom calls normally ring. If disabled, intercom calls voice-announce....
Page 1655
Univerge sv8100 issue 11.0 ucb (unified communications for business) 2 - 1623 20-23-06 system options for cti – 3rd party cti ip address read only program that displays the ip address of the currently connected 3rd party cti server. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 191.255.255.254 192.0.0.1~ 223....
Page 1656
Issue 11.0 univerge sv8100 2 - 1624 ucb (unified communications for business) operation ucb provides a comprehensive suite of online help for end users, customer administrators, and call center supervisors. Refer to the product manuals for the core applications: q-control, q-reports, q-desktop and t...
Page 1657: Um8000 Mail
Univerge sv8100 issue 11.0 um8000 mail 2 - 1625 um8000 mail description the um8000 mail voice mail system, using the univerge sv8100 system and a local area network, provide unified messaging services for voice, fax and email messages with access at either the desktop pc or the telephone. Unified me...
Page 1658
Issue 11.0 univerge sv8100 2 - 1626 um8000 mail call forwarding to voice mail an extension user can forward their calls to voice mail. Once forwarded, calls to the extension connect to that extension mailbox. The caller can leave a message in the mailbox instead of calling back later. Forwarding can...
Page 1659
Univerge sv8100 issue 11.0 um8000 mail 2 - 1627 voice mail caller id the voice mail can use ani/dnis information to identify the outside caller that left a message in a user’s mailbox. When the message recipient dials 0 or presses the cid softkey while listening to a message, they hear the outside t...
Page 1660
Issue 11.0 univerge sv8100 2 - 1628 um8000 mail 2. The directory dialing mailbox plays the directory dialing message which asks the caller to dial letters for the name of the person they wish to reach. 3. The caller dials the first three letters for the person’s name. They can dial by first name or ...
Page 1661
Univerge sv8100 issue 11.0 um8000 mail 2 - 1629 viewcall ® plus all inbound and outbound calls can be controlled from your pc. Outbound call control requires a tapi adaptor on the user telephone. By managing calls on the pc instead of the telephone, viewcall plus lets you communicate more easily wit...
Page 1662
Issue 11.0 univerge sv8100 2 - 1630 um8000 mail email integration with email integration, subscribers can forward all voice messages to their email inbox automatically and forward all incoming faxes to their email inbox as well. Email integration provides users with 24-hour access to email from any ...
Page 1663
Univerge sv8100 issue 11.0 um8000 mail 2 - 1631 conditions the expanded schedule feature has the following conditions: requires version 11.5.0.Xx or higher um8000 mailsoftware. A maximum of 99 custom schedules are supported. A maximum of nine time intervals per custom schedule are supported to set m...
Page 1664
Issue 11.0 univerge sv8100 2 - 1632 um8000 mail updating the system time also updates the um8000 mail time. When setting up hunt group priorities in 16-02-01 the vm ports must be assigned as port 1 = priority 1, port 2 = priority 2 and so on. Failure to do this causes the vm to answer but no audio i...
Page 1665
Univerge sv8100 issue 11.0 um8000 mail 2 - 1633 if the message waiting led is also used for message waiting indication, and there are both voice mail messages and message wait indications, the color set for message wait overrides the color used for voice mail indications (red). During a conversation...
Page 1666
Issue 11.0 univerge sv8100 2 - 1634 um8000 mail required software when using viewmail for microsoft messaging (vmm) with office xp/2002 or office 2000 you must have at least service pack 3 for office installed prior to installing vmm. Failure to do so requires removing and installing the entire offi...
Page 1667
Univerge sv8100 issue 11.0 um8000 mail 2 - 1635 central office calls, answering central office calls, placing direct inward line (dil) hold message waiting one-touch calling programmable function keys transfer guide to feature programming the level 1, level 2 and level 3 columns indicate the program...
Page 1668
Issue 11.0 univerge sv8100 2 - 1636 um8000 mail 10-55-01 package network setup – ip address define the ip address for the cd-etia. When the blade is deleted from the system using program 90-05, the programming for the slot in 10-55 is set back to default. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 191.2552...
Page 1669
Univerge sv8100 issue 11.0 um8000 mail 2 - 1637 10-55-05 package network setup – default gateway define the default gateway for the cd-etia. 0.0.0.0~ 126.255.255.254 128.0.0.1~ 191.255255.254 192.0.0.1~ 223.255.255.254 (default = 0.0.0.0) 11-07-01 department group pilot numbers – dial assign a depar...
Page 1670
Issue 11.0 univerge sv8100 2 - 1638 um8000 mail 15-03-01 single line telephone basic data setup – slt signaling type for each univerge sv8100 voice mail extension, set this option to 1. 0 = dp 1 = dtmf (default = 1) 15-03-03 single line telephone basic data setup – terminal type enter 1 for this opt...
Page 1671
Univerge sv8100 issue 11.0 um8000 mail 2 - 1639 16-02-01 department group assignment for extensions set the department group called by the pilot number and the extension priority when a group is called. Call pickup groups are set up in 23-02. When setting up hunt group priorities the vm ports must b...
Page 1672
Issue 11.0 univerge sv8100 2 - 1640 um8000 mail 20-11-05 class of service options (hold/ transfer service) – call forwarding with follow me turn off or on an extension user ability to set call forwarding with follow me. 0 = off 1 = on (default = 1 for cos 1~15) 20-11-12 class of service options (hol...
Page 1673
Univerge sv8100 issue 11.0 um8000 mail 2 - 1641 assign trunks as automated attendant trunks – method 1: 22-01-04 system options for incoming calls – dil no answer recall time a dil that rings its programmed destination longer than this time diverts to the dil no answer ring group (set in program 22-...
Page 1674
Issue 11.0 univerge sv8100 2 - 1642 um8000 mail assign trunks as automated attendant trunks – method 2: for either method: program number program name description/comments assigned data level 1 2 3 22-02-01 incoming call trunk setup assign 0 to each trunk you want to ring into voice mail as a normal...
Page 1675
Univerge sv8100 issue 11.0 um8000 mail 2 - 1643 22-08-01 dil/irg no answer destination for voice mail overflow, enter the ring group that unanswered dils to voice mail ring after the dil call waiting time expires (program 22-01-04). 0 (no setting) 001~100 (incoming ring group) 102 (in-skin/ external...
Page 1676
Issue 11.0 univerge sv8100 2 - 1644 um8000 mail 45-01-06 voice mail integration options – record alert tone interval time set the time between voice mail conversation record alerts. 0~64800 (seconds) (default = 30) 45-01-18 voice mail integration options – trunk number mapping assign the digits of t...
Page 1677
Univerge sv8100 issue 11.0 um8000 mail 2 - 1645 80-03-03 dtmf tone receiver setup – min. Detect level define the minimum detection level for dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20dbm(0) to – 35dbm(15) detect level...
Page 1678
Issue 11.0 univerge sv8100 2 - 1646 um8000 mail 80-03-04 dtmf tone receiver setup – max. Detect level define the maximum detection level for dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(0) to – 25dbm(15) detect level 3:...
Page 1679
Univerge sv8100 issue 11.0 um8000 mail 2 - 1647 80-03-05 dtmf tone receiver setup – forward twist level define the forward twist level for dtmf tone receiver. 0~9 (1db~10db) default: type 1~5 = 5 (6dbm) 80-03-06 dtmf tone receiver setup – backward twist level define the backwards twist level for dtm...
Page 1680
Issue 11.0 univerge sv8100 2 - 1648 um8000 mail 80-04-02 call progress tone detector setup – min. Detection level define the various levels and timers for the call progress tone detector. Use this option to set the minimum detection level. 0~15 detect level 0: –15dbm(0) to –30dbm(15) detect level 1:...
Page 1681
Univerge sv8100 issue 11.0 um8000 mail 2 - 1649 80-04-05 call progress tone detector setup – pulse count define the various levels and timers for the call progress tone detector. Use this option to set the pulse count. 1~255 default: type 1 (dt) = 1 type 2 (bt) = 1 type 3 (rbt) = 1 type 4, type 5 = ...
Page 1682
Issue 11.0 univerge sv8100 2 - 1650 um8000 mail operation refer to vm8000 inmail on page 2-1723 for complete telephone operation procedures..
Page 1683: Umobility
Univerge sv8100 issue 11.0 umobility 2 - 1651 umobility description the umobility system is designed to enhance the mobile user’s experience by bringing features and functionality from office or residential services right to the smart phone. The umobility system allows the user to: answer the office...
Page 1684
Issue 11.0 univerge sv8100 2 - 1652 umobility the setting in prg 99-01-60 affects sip messages when using the call forward with both ring feature (twinning). For the umobility and desk phone to work together properly, this must be set to 1 (on). The default is 0 (off). The following conditions apply...
Page 1685
Univerge sv8100 issue 11.0 umobility 2 - 1653 when a umobility device is on a call, a second call to that device does not follow forwarding. Call forward with both ring is not supported across k-ccis networks. Therefore, the desk phone, the umc server and the umobility mobile device must be in the s...
Page 1686
Issue 11.0 univerge sv8100 2 - 1654 umobility there should be three reserve pool users for every 10 umobility users that are connected to your ip-pbx system. For example, if you have 25 umobility users then you should create eight reserve pool users in both ip-pbx and umobility. Caller id informatio...
Page 1687
Univerge sv8100 issue 11.0 umobility 2 - 1655 system availability terminals refer to the necworx website for application note ansv8100-09-007 containing the current list of supported mobile devices. Required component(s) version 3000 or higher software and appropriate licenses third party sip licens...
Page 1688
Issue 11.0 univerge sv8100 2 - 1656 umobility feature support tables for each supported mobile device: table 2-104 windows mobile devices feature/service description umobility sv8100 dual mode operations (umobility features and services in both wifi and cellular domain) yes handoff operations (ho) y...
Page 1689
Univerge sv8100 issue 11.0 umobility 2 - 1657 bluetooth no presentation (pbx/cm dependent) blind call transfer no consultative call transfer yes (only in wifi domain) mid-call dtmf numeric keys, excluding * and #. Yes voicemail message waiting indicator (mwi) yes (cellular data network dependent. En...
Page 1690
Issue 11.0 univerge sv8100 2 - 1658 umobility abbreviated extension dialing yes mid-call dtmf numeric keys, excluding * and #. Yes basic telephony (device dependent) speed dial no missed call indication yes (both wifi and cellular) call logs yes contact dialing yes mute/unmute yes speakerphone yes v...
Page 1691
Univerge sv8100 issue 11.0 umobility 2 - 1659 basic telephony (pbx/cm dependent) enterprise dialing (ed) call forward all (cfa) yes call forward busy (cfb) yes call forward no answer (cfna) yes call hold and resume yes call waiting no conference call yes (participant only) calling line identificatio...
Page 1692
Issue 11.0 univerge sv8100 2 - 1660 umobility guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature programm...
Page 1693
Univerge sv8100 issue 11.0 umobility 2 - 1661 10-12-10 cd-cp00-us network setup – subnet mask set the subnet mask of the ipla. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 255.254.0.0 255.255.0...
Page 1694
Issue 11.0 univerge sv8100 2 - 1662 umobility 14-02-23 analog trunk data setup – caller id receiving method rings extension before receiving caller id (1) or after receiving caller id (0). If caller id is received on a trunk that is in the same ring group as a umobility client device this should be ...
Page 1695
Univerge sv8100 issue 11.0 umobility 2 - 1663 16-01-03 department group basic data setup – department routing when busy (auto step call) set how the system routes an intercom call to a busy department group member. Intercom callers to the extension can either hear busy or route to the first availabl...
Page 1696
Issue 11.0 univerge sv8100 2 - 1664 umobility 24-02-04 system options for transfer – transfer recall time set the transfer recall time. An unanswered transferred call recalls to the extension that initially transferred it after this time. This also sets the time a transferred call camps-on to a busy...
Page 1697
Univerge sv8100 issue 11.0 umobility 2 - 1665 umc server configuration for sv8100: 84-26-01 ipl basic setup – ip address assign the ip address for each dsp on the ipla. Xxx.Xxx.Xxx.Xxx defaults: slot 1 = 172.16.0.20 : slot 4 = 172.16.0.44 voip gw 1~8: 172.16.0.20~ 172.16.0.27 99-01-60 options 60 thi...
Page 1698
Issue 11.0 univerge sv8100 2 - 1666 umobility operation none ho_cell_autoanswer_clid this filed should have all possible outgoing trunk caller id for the umc server port. This information is provided to the umobility client device so it knows when an incoming call is from the umc server. Refer to th...
Page 1699
Univerge sv8100 issue 11.0 unicast/multicast paging mode 2 - 1667 unicast/multicast paging mode description with version 3000 or higher software the ip terminals (dt7xx) can now receive an internal page via a unicast or multicast packet based upon system programming. This feature allows ip terminals...
Page 1700
Issue 11.0 univerge sv8100 2 - 1668 unicast/multicast paging mode figure 2-45 multicast mode example figure 2-46 unicast mode example.
Page 1701
Univerge sv8100 issue 11.0 unicast/multicast paging mode 2 - 1669 by default routers do not pass multicast packets between subnets. If you have ip phones in different subnets than the ipla, and you are trying to utilize multicast paging, you have to program the router to pass the multicast packet. R...
Page 1702
Issue 11.0 univerge sv8100 2 - 1670 unicast/multicast paging mode you can assign up to 16 ip phones in an internal or all call paging group. When using unicast mode, there must be an available dsp recourse for each ip phone in the page group at the time of the internal page. If the resources are les...
Page 1703
Univerge sv8100 issue 11.0 unicast/multicast paging mode 2 - 1671 router that supports multicast packets if utilizing multicast mode related features ip multiline station (sip) meet me paging meet me paging transfer paging, external paging, internal guide to feature programming the level 1, level 2 ...
Page 1704
Issue 11.0 univerge sv8100 2 - 1672 unicast/multicast paging mode 10-46-12 dt700 server information setup – multicast port sets the starting port number used by multicast. 0~65535 (default = 30000) 11-12-19 service code setup (for service access) – internal group paging service code setup. Mlt, slt ...
Page 1705
Univerge sv8100 issue 11.0 unicast/multicast paging mode 2 - 1673 operation to make an internal page announcement: multiline terminal/ip terminal/mh240 1. Press the zone internal paging key (program 15-07 or sc 751: 21 + 0 or 1~9 or 01~64 for zones (0 or 00 for all call). - or - press speaker or lif...
Page 1706
Issue 11.0 univerge sv8100 2 - 1674 unicast/multicast paging mode single line telephone/sip dect wireless 1. Lift the handset. 2. Dial 701 and the paging zone number (0~9 or 00~64). Dialing 0 or 00 calls all call internal paging. Dial 1 and the combined paging group code 1~8 or 0 (for internal/exter...
Page 1707
Univerge sv8100 issue 11.0 uniform call distribution (ucd) 2 - 1675 uniform call distribution (ucd) description with uniform call distribution (ucd), an extension user can call an idle extension in a preprogrammed ucd group (department group – 64 department groups available) by dialing the group pil...
Page 1708
Issue 11.0 univerge sv8100 2 - 1676 uniform call distribution (ucd) the vrs can also transfer calls to ucd (department) groups. Refer to the voice response system (vrs) on page 2-1911 feature for more information on setting up the vrs. The system prevents hunting to a ucd (department) group extensio...
Page 1709
Univerge sv8100 issue 11.0 uniform call distribution (ucd) 2 - 1677 priority routing figure 2-48 uniform call distribution (ucd) priority call routing priority 1 priority 2 priority 3 priority 2 priority 3 priority 2 priority 3 call telephone on a call telephone on a call priority 1 priority 1 call ...
Page 1710
Issue 11.0 univerge sv8100 2 - 1678 uniform call distribution (ucd) circular routing figure 2-49 uniform call distribution (ucd) circular routing call 1 call 2 call 3 call 4.
Page 1711
Univerge sv8100 issue 11.0 uniform call distribution (ucd) 2 - 1679 system availability terminals all terminals required component(s) pz-vm21 and vrs compact flash (for delay announcements) related features automatic call distribution (acd) call forwarding call arrival (car) keys transfer vm8000 inm...
Page 1712
Issue 11.0 univerge sv8100 2 - 1680 uniform call distribution (ucd) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizard...
Page 1713
Univerge sv8100 issue 11.0 uniform call distribution (ucd) 2 - 1681 16-01-04 department group basic data setup – hunting mode set the action taken when a call reaches the last extension of the department group. 0 = last extension is called and hunting is stopped 1 = circular (default = 0) 16-01-05 d...
Page 1714
Issue 11.0 univerge sv8100 2 - 1682 uniform call distribution (ucd) 16-03-01 secondary department group assign extensions to multiple department groups and set the priority assignment. Each secondary department group can have up to 16 extensions assigned. Extension number maximum eight digits priori...
Page 1715
Univerge sv8100 issue 11.0 uniform call distribution (ucd) 2 - 1683 operation to call a ucd group: 1. At the multiline terminal, press speaker. - or - at single line telephone, lift the handset. 2. Dial the ucd group (department) extension or pilot number. The system routes the call to the first fre...
Page 1716
Issue 11.0 univerge sv8100 2 - 1684 uniform call distribution (ucd) to log back in to your ucd (department calling) group: while you log back in, uniform call distribution routes calls to your extension. 1. Press speaker. 2. Dial 650 and 0. - or - press ucd (department calling) log in key (program 1...
Page 1717: Uniform Numbering Network
Univerge sv8100 issue 11.0 uniform numbering network 2 - 1685 uniform numbering network description uniform numbering network allows multiple or compatible systems to be connected in a network using tie lines. A station user can dial a system number and a station number (open numbering) or dial the ...
Page 1718
Issue 11.0 univerge sv8100 2 - 1686 uniform numbering network default setting none system availability terminals all terminals required component(s) cd-4odta -or- cd-prta related features automatic route selection flexible system numbering k-ccis – ip k-ccis – t1 multiple trunk types.
Page 1719
Univerge sv8100 issue 11.0 uniform numbering network 2 - 1687 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for ...
Page 1720
Issue 11.0 univerge sv8100 2 - 1688 uniform numbering network 14-02-14 analog trunk data setup – loop start/ground start define an analog trunk as loop start or ground start. 0 = loop start 1 = ground start (default = 0) 14-05-01 trunk group – trunk group number assign trunks to trunk groups (1~100)...
Page 1721
Univerge sv8100 issue 11.0 uniform numbering network 2 - 1689 44-03-01 dial analysis extension table – dial set the dial digits (24 digits maximum) 1~9, 0 # , @) to be used for the dial extension analysis table. When program 44-02-02 is set to 3, this program sets the dial extension analysis table...
Page 1722
Issue 11.0 univerge sv8100 2 - 1690 uniform numbering network 44-05-02 ars/f-route table – delete digits enter the number of digits to be deleted from the dialed number [0~255 (255 = delete all)]. 0~255 (255 = delete all) (default = 0) 44-05-03 ars/f-route table – additional dial number table enter ...
Page 1723
Univerge sv8100 issue 11.0 uniform numbering network 2 - 1691 44-06-01 additional dial table set the additional dial table to add prior to the dialed ars/f-route number. The additional dial table used is determined in program 44-05-03. Define the additional dial table (1~1000) to add digits in front...
Page 1724
Issue 11.0 univerge sv8100 2 - 1692 uniform numbering network operation none 44-09-01 weekly schedule for ars/ f-route define a weekly schedule for using ars/f-route day numbers 1~7, pattern numbers (1~10). The pattern number is defined in program 44-08-01. 1 = sunday (pattern 1~10) (default pattern...
Page 1725: Universal Slots
Univerge sv8100 issue 11.0 universal slots 2 - 1693 universal slots description the univerge sv8100 has six universal slots, and up to four cabinets can be installed. The system uses the same chassis for the 64, 256 and unlimited systems to support up to 24 universal slots. Up to four combined chs2u...
Page 1726
Issue 11.0 univerge sv8100 2 - 1694 universal slots table 2-107 sv8100 maximum system capacities – trunks/ports/channels number of: 9.5” chassis 19” chassis system maximum x 1 (cpu + 2 slots) x 1 (6 slots) x 2 (12 slots) x 3 (18 slots) x4 (24 slots) number of timeslots 1 pcm 48 104 208 312 416 444 d...
Page 1727
Univerge sv8100 issue 11.0 universal slots 2 - 1695 table 2-108 sv8100 9.5” (base and expansion) maximum system capacities – trunks/ports/channels number of: 9.5” base 9.5” base + expansion system maximum x 1 (cpu + 2 slots) x 1 (6 slots) x 2 (12 slots) x 3 (18 slots) x4 (24 slots) number of timeslo...
Page 1728
Issue 11.0 univerge sv8100 2 - 1696 universal slots each universal slot is capable of 24 ports. The basic port package is limited to one chassis. The prta blades can be programmed as a 4/8/12/16/20/24 port fractional t1/pri. Program 10-39-01 must be enabled). If trying to assign an blade which would...
Page 1729
Univerge sv8100 issue 11.0 universal slots 2 - 1697 cd-16dlca these blades are 16-port. Each circuit can support any attendant console, multiline terminal, or single line telephone adapter. This blade is installed in slots 2~6 of a chassis with cpu and slots 1~6 of expansion chassis. The maximum num...
Page 1730
Issue 11.0 univerge sv8100 2 - 1698 universal slots cd-4lca this 4-port single line interface blade supports four single line telephones and/or analog voice mail ports. Each blade provides a built-in ringer signal generator (rsg) and message waiting (mw) led voltage to single line telephones. This b...
Page 1731
Univerge sv8100 issue 11.0 universal slots 2 - 1699 pz-4lca this daughter board is a 4-port single line interface. The pz-4lca is installed on the cd-4lca, and supports four single line telephones with built-in ringer signal generator (rsg) and message waiting (mw) led voltage to single line telepho...
Page 1732
Issue 11.0 univerge sv8100 2 - 1700 universal slots table 2-110 maximum system capacities for trunk interface blades trunk interface blades description maximum capacities notes basic port package expanded port package cd-2bria/ pz-2bria this 2/4-port basic rate interface for up to eight trunks provi...
Page 1733
Univerge sv8100 issue 11.0 universal slots 2 - 1701 cd-prta this t1/ft1 trunk interface or isdn-primary rate digital trunk terminates fractional t1 trunks (up to 24 ds-0 channels). This blade supports ani/dnis trunks, and csu less function on t1. A combination of ground start and loop start signalin...
Page 1734
Issue 11.0 univerge sv8100 2 - 1702 universal slots cd-4odta the cd-4odta tie line blade is an out band dial type analog tie line interface blade. This blade supports system connections to either 2-wire (four lead, tip/ring) or 4-wire (eight lead, tip/ring/tip 1/ ring 1) e&m signalling tie lines (de...
Page 1735
Univerge sv8100 issue 11.0 universal slots 2 - 1703 refer to the sv8100 general description manual or system hardware manual for more information. The following blade calculator allows you to determine the maximum power consumption for each cabinet. Cd-etia the cd-etia is an 8-port gigabit switch th...
Page 1736
Issue 11.0 univerge sv8100 2 - 1704 universal slots table 2-113 terminal power factor terminal power factor 19 inch metal chassis with fan = 9.5 inch plastic chassis without fan = item power factor dtl-24d-1 tel 0.8 dtl-8ld-1 tel 0.8 bha-l unit 2 ada-l unit 2 apr-l unit dt300 series : 2 d term serie...
Page 1737
Univerge sv8100 issue 11.0 universal slots 2 - 1705 for sv8100 systems with version 4000 or higher system software and has been migrated from a ux5000, table 2-115 migration supported application blades defines the application blades supported in current system chassis. Default setting none table 2-...
Page 1738
Issue 11.0 univerge sv8100 2 - 1706 universal slots system availability terminals none required component(s) any blade related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they a...
Page 1739
Univerge sv8100 issue 11.0 universal slots 2 - 1707 operation none 90-34-01 firmware information – pkg name list the package type and firmware for the packages installed. The data varies depending on the card in the slot. 90-34-02 firmware information – firmware version number view the package name ...
Page 1740
Issue 11.0 univerge sv8100 2 - 1708 universal slots this page intentionally left blank.
Page 1741: User Programming Ability
Univerge sv8100 issue 11.0 user programming ability 2 - 1709 user programming ability description a station user can perform programming functions. Speed group dialing and function keys are just two features programmable from a station. Conditions multiline terminals must be idle and off-hook and ha...
Page 1742
Issue 11.0 univerge sv8100 2 - 1710 user programming ability guide to feature programming none operation none.
Page 1743: Virtual Extensions
Virtual extensions 2 - 1711 v virtual extensions description virtual extensions are available software extensions on the basic and expanded port packages. A virtual extension assigned to a line key can appear and ring on an individual station or multiple stations and be used for outbound access. Vir...
Page 1744
Issue 11.0 univerge sv8100 2 - 1712 virtual extensions up to 32 incoming calls can be queued to busy virtual extension key. You cannot have a car key and virtual extension on the same telephone. Virtual extensions do not support the following features: barge-in conference conference, voice call/priv...
Page 1745
Univerge sv8100 issue 11.0 virtual extensions 2 - 1713 when an internal station-to-station call is made to a virtual extension, the name and number of the calling party does not appear in the display of the station the virtual extension resides on until the call is answered. A door box cannot ring a...
Page 1746
Issue 11.0 univerge sv8100 2 - 1714 virtual extensions with version 8000 or higher software, the number of tone patterns increased from four to eight. After setting new system data (tone patterns 5 - 8), downgrading to version 7000 or lower may cause incoming rings to not function properly. Default ...
Page 1747
Univerge sv8100 issue 11.0 virtual extensions 2 - 1715 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature...
Page 1748
Issue 11.0 univerge sv8100 2 - 1716 virtual extensions 15-02-21 multiline telephone basic data setup – virtual extension access mode (when idle virtual extension key pressed) determine whether an extension virtual extension key should be used as a dss key to the extension and for receiving calls (0)...
Page 1749
Univerge sv8100 issue 11.0 virtual extensions 2 - 1717 15-10-01 virtual incoming extension ring tone order setup when two or more virtual extensions are set on a function key on the telephone, and the tone pattern by which the sound of each extension differs, the priority of ring sound is set up. 0 ...
Page 1750
Issue 11.0 univerge sv8100 2 - 1718 virtual extensions 15-18-04 virtual extension key enhanced options – show internal caller information when set to a 0, internal calls to the virtual extension will not show the name or number of the extension that is calling. When set to 1, internal calls to the v...
Page 1751
Univerge sv8100 issue 11.0 virtual extensions 2 - 1719 20-06-01 class of service for extensions assign the extension to a class of service. Day night/mode: 1~8 class of service of extensions (1~15) default: extension port 101 = class 15 all other extension port = class 1 20-07-10 class of service op...
Page 1752
Issue 11.0 univerge sv8100 2 - 1720 virtual extensions operation to answer a call ringing a virtual extension: 1. Press the flashing virtual extension key. - or - go off-hook. Program 20-10-08 needs to be set to on (1) for extension class of service. To place a call to a virtual extension: 1. Go off...
Page 1753
Univerge sv8100 issue 11.0 virtual extensions 2 - 1721 8. Press hold for a second time for delayed ring, or skip to step 10. 9. Dial the mode number in which the key delay rings. 1 = day 1 2 = night 1 3 = midnight 1 4 = rest 1 5 = day 2 6 = night 2 7 = midnight 2 8 = rest 2 10. Press speaker..
Page 1754
Issue 11.0 univerge sv8100 2 - 1722 virtual extensions this page intentionally left blank.
Page 1755: Vm8000 Inmail
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1723 vm8000 inmail enhancements version 4000 or higher software provides the following: security code enhancement. After a subscriber sets their security code, they can choose to make it required for all logons or just remote logons. When enabled for all ...
Page 1756
Issue 11.0 univerge sv8100 2 - 1724 vm8000 inmail description the vm8000 inmail is a low cost voice mail solution that mounts on the cd-cp00-us. Its programming is fully integrated with chassis programming. This system offers most voice mail system features customers expect. Automated attendant auto...
Page 1757
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1725 live monitor a multiline terminal user can have their idle extension emulate a personal answering machine. This lets inmail screen their calls, just like their answering machine at home. If activated, the extension incoming calls route to the user’s ...
Page 1758
Issue 11.0 univerge sv8100 2 - 1726 vm8000 inmail as the voice mail queue follows department hunting programming, the queue can hold a maximum of 10 calls. If the queue is full or if the voice mail ports are not assigned to a department group, the calls are handled as though no voice mail queuing fe...
Page 1759
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1727 vm8000 inmail: external transfer available the software allows the vm8000 inmail to perform an external transfer. This allows the vm8000 inmail to route an incoming automated attendant call out of the univerge sv8100 system on a new trunk based on an...
Page 1760
Issue 11.0 univerge sv8100 2 - 1728 vm8000 inmail 5. Voice prompts announce the first three matches, and allow the caller to dial a digit (1~3) to reach one of the announced matches. Additionally, the caller can dial 4 to hear additional matches (if any). 6. The caller dials the digit for the extens...
Page 1761
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1729 conditions remote ccis extensions are not supported in a centralized directory. When set for unscreened transfer, calls from the inmail ring at the extension like other transferred calls and display the incoming caller id data (if provided by telco a...
Page 1762
Issue 11.0 univerge sv8100 2 - 1730 vm8000 inmail the quick transfer to voice mail is not allowed when caller is: listening to the busy tone (bt). Talking on an internal line. Talking on an outside line. Making a conference call. The following features require version 6000 or higher software and ver...
Page 1763
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1731 off-premise notification and external extensions require access to outside lines. When the voice mail places a call on hold, it uses group hold. Any line appearances for the trunk shows the hold flash rate, however, a user cannot pick up this call (a...
Page 1764
Issue 11.0 univerge sv8100 2 - 1732 vm8000 inmail the number of speech path channels on the cd-cp00-us (cpu) for the vm8000 (in mail) and the vrs feature are shared and depends if the pz-me50 daughter board is installed. Without a pz-me50 daughter board installed the systems supports a maximum of ei...
Page 1765
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1733 caller id call forwarding central office calls, placing clock/calendar display direct inward line (dil) hold message waiting one-touch calling programmable function keys transfer.
Page 1766
Issue 11.0 univerge sv8100 2 - 1734 vm8000 inmail guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature prog...
Page 1767
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1735 15-02-26 multiline telephone basic data setup – msg key operation mode determine whether an extension msg key should function as a message key or voice mail key. If set as a message key, the user can press it to call the voice mail only when they hav...
Page 1768
Issue 11.0 univerge sv8100 2 - 1736 vm8000 inmail 15-07-01 programmable function keys assign a voice mail key to an extension. You must enter the voice mail key code (code 77) followed by: your own extension number if you are setting up your own voice mail key. A virtual extension number if you are ...
Page 1769
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1737 20-09-01 class of service options (incoming call service) – second call for did/disa/dil/ e&m turn off or on the extension ability to receive a second call from a did, disa, dil, or tie line caller. With this option set to 1, the destination extensio...
Page 1770
Issue 11.0 univerge sv8100 2 - 1738 vm8000 inmail 20-13-05 class of service options (supplementary service) – intercom off-hook signaling turn on or off an extension ability to receive off-hook signals. 0 = off 1 = on (default = 1 for cos 01~15) 20-13-06 class of service options (supplementary servi...
Page 1771
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1739 assign trunks as automated attendant trunks – method 1: 24-02-02 system options for transfer – moh or ringback on transferred calls enable/disable moh on transfer. If set to 0, a transferred caller hears music on hold while their call rings the desti...
Page 1772
Issue 11.0 univerge sv8100 2 - 1740 vm8000 inmail assign trunks as automated attendant trunks – method 2: for either method: program number program name description/comments assigned data level 1 2 3 22-02-01 incoming call trunk setup assign service type 0 to each trunk you want to ring into voice m...
Page 1773
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1741 24-02-03 system options for transfer – delayed call forwarding time set the time a transferred call waits at a forwarded extension before routing to the called extension mailbox. 0~64800 (seconds) (default = 10) 45-01-01 voice mail integration option...
Page 1774
Issue 11.0 univerge sv8100 2 - 1742 vm8000 inmail 47-01-02 sv8100 inmail system options – sv8100 inmail master name the chs2u gw-us must be reset for a change to this program to take effect. Use this option to modify the name for all vm8000 inmail ports. The system briefly displays this name when a ...
Page 1775
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1743 47-01-04 sv8100 inmail system options – non-subscriber message length set the maximum time for recorded messages for: automated attendant callers leaving a message or quick message in a subscriber mailbox. Outside callers transferred by an extension ...
Page 1776
Issue 11.0 univerge sv8100 2 - 1744 vm8000 inmail 47-01-08 sv8100 inmail system options – delay in dialing digital pager callback number set the time delay (0~99 seconds) that occurs just before vm8000 inmail dials the digital pager callback number portion of the message notification callout number ...
Page 1777
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1745 47-01-10 sv8100 inmail system options – wait between non-pager callout attempts set the minimum time between non-pager message notification callouts in which the destination answers, says hello, dials 1 to acknowledge and then enters the wrong securi...
Page 1778
Issue 11.0 univerge sv8100 2 - 1746 vm8000 inmail 47-01-14 sv8100 inmail system options – number of cascading attempts set how many times vm8000 inmail retries an incomplete message notification callout. This total includes unacknowledged callouts, callouts to a busy destination, and callouts to an ...
Page 1779
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1747 47-01-17 sv8100 inmail system options – inmail port specify the port number of the first inmail port. Setting this program requires a cd-cp00-us reset for the changes to take effect. With software version 1.11 or higher the following rules apply when...
Page 1780
Issue 11.0 univerge sv8100 2 - 1748 vm8000 inmail 47-02-02 sv8100 inmail station mailbox options – mailbox number select the extension number associated with the mailbox you are programming. Normally, mailbox 1 should use mailbox number 101, mailbox 2 should use mailbox number 102, etc. To make prog...
Page 1781
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1749 47-02-07 sv8100 inmail station mailbox options – recording conversation beep enable/disable the conversation record beep. If enabled, all parties on a call hear the voice prompt recording followed by a single beep when the extension user initiates co...
Page 1782
Issue 11.0 univerge sv8100 2 - 1750 vm8000 inmail 47-02-10 sv8100 inmail station mailbox options – forced unscreened transfer enable/disable automated attendant forced unscreened transfer for the subscriber mailbox. If enabled, each screened transfer (trf) to the extension is converted to an unscree...
Page 1783
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1751 47-02-15 sv8100 inmail station mailbox options – directory list number set up a station/extension mailbox directory list. 0 = none 1~8 = list number = all (default = 0) 47-02-26 sv8100 inmail station mailbox options – auto play use this option to set...
Page 1784
Issue 11.0 univerge sv8100 2 - 1752 vm8000 inmail 47-06-03 group mailbox subscriber options – auto erase/save of messages determine what happens when a subscriber mailbox user completely listens to a new message and then exits the mailbox without either saving (sa) or erasing (e) the message. Depend...
Page 1785
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1753 47-06-06 group mailbox subscriber options – message waiting lamp enable/disable message waiting lamp at the extension associated with the subscriber mailbox. For subscriber mailboxes, you should enable this option. For guest mailboxes, you should dis...
Page 1786
Issue 11.0 univerge sv8100 2 - 1754 vm8000 inmail 47-06-11 group mailbox subscriber options – dialing option dialing option provides additional dialing options for next call routing mailbox calls (see next call routing mailbox below). If enabled, a caller who accesses the subscriber mailbox to leave...
Page 1787
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1755 47-08-02 call routing mailbox options – screened transfer timeout set the time a screened transfer (trf) from the automated attendant rings an unanswered extension before recalling. This option has a similar function as customize: mailbox options: ca...
Page 1788
Issue 11.0 univerge sv8100 2 - 1756 vm8000 inmail 47-09-01 announcement mailbox options – next call routing mailbox if you set up an announcement mailbox to answer automated attendant calls, use this option to provide additional routing options to the automated attendant callers. This option interac...
Page 1789
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1757 47-11-01 vm8000 inmail answer table options – answer schedule override enable/disable answer schedule override for the selected answer table. If enabled (and you make an entry for override mailbox below), the active answer table routes calls to the o...
Page 1790
Issue 11.0 univerge sv8100 2 - 1758 vm8000 inmail 47-11-02 vm8000 inmail answer table options – override mailbox category specify the category of the mailbox where automated attendant calls should route when you enable answer schedule override. Vm8000 inmail mailbox categories are subscriber mailbox...
Page 1791
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1759 47-11-03 vm8000 inmail answer table options – default mailbox category specify the category of mailbox used as the default mailbox. Vm8000 inmail mailbox categories are subscriber mailbox, master mailbox, and routing mailbox. Vm8000 inmail uses the d...
Page 1792
Issue 11.0 univerge sv8100 2 - 1760 vm8000 inmail 47-12-01 vm8000 inmail answer schedules – schedule type assign a schedule type to the selected answer schedule. The schedule type determines how the answer schedule answers calls. The schedule can be one of the following types: 1. Day of the week a t...
Page 1793
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1761 47-12-02 vm8000 inmail answer schedules – answering mailbox category specify the category of mailbox to which automated attendant calls should route when the schedule is in effect. Vm8000 inmail mailbox categories are subscriber mailbox, master mailb...
Page 1794
Issue 11.0 univerge sv8100 2 - 1762 vm8000 inmail 47-12-04 vm8000 inmail answer schedules – start day for range of days (type 2) answer schedules, select the day of the week the answer schedule should start. 1 = sunday 2 = monday 3 = tuesday 4 = wednesday 5 = thursday 6 = friday 7 = saturday default...
Page 1795
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1763 47-12-08 vm8000 inmail answer schedules – schedule end time specify the time the answer schedule should start. It applies to day of the week (type 1), range of days (type 2), and date (type 3) schedules. (to make a schedule run continuously, make the...
Page 1796
Issue 11.0 univerge sv8100 2 - 1764 vm8000 inmail acd delay announcement: only use if master mailboxes are used for acd delay announcements. Program number program name description/comments assigned data level 1 2 3 41-19-01 acd voice mail delay announcement – delay message start timer determine the...
Page 1797
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1765 operation calling your mailbox: to call your mailbox: with a multiline terminal, your voice mail key flashes green and your message center keys flash red when they have messages waiting. If you do not have a voice mail key, your message waiting led f...
Page 1798
Issue 11.0 univerge sv8100 2 - 1766 vm8000 inmail checking messages: if program 15-02-26 = 0 (message key): 1. Press the message key once. The user can use the vol up and vol down keys to view the new messages. If there are both voice mail messages and message waiting calls, the display indicates th...
Page 1799
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1767 forwarding calls to your mailbox: to activate or cancel call forwarding: 1. Press speaker (or lift the handset at the single line telephone) and choose from the following dial access codes: 741 = call forward – immediate (program 15-07 or sc 751: cod...
Page 1800
Issue 11.0 univerge sv8100 2 - 1768 vm8000 inmail 3. Hang up. Voice mail prompts your caller to leave a message in the mailbox you selected. Single line telephone 1. Hookflash. Dial voice mail master number followed by destination mailbox. If the transfer destination is an extension forwarded to voi...
Page 1801
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1769 personal answering machine emulation (multiline terminal only): to enable or cancel personal answering machine emulation: 1. Press speaker (or lift the handset at the single line telephone) and choose from the following dial access codes: 741 = call ...
Page 1802
Issue 11.0 univerge sv8100 2 - 1770 vm8000 inmail 2. Dial 0. You can have any combination of the message types in the table below on your telephone. 3. Press vol or vol to scroll through your display. 4. When you find the message you want to answer, press speaker. You can either: go to your voic...
Page 1803
Univerge sv8100 issue 11.0 vm8000 inmail 2 - 1771 using directory dialing: 1. After the automated attendant answers, wait for the directory dialing message. The automated attendant may ask you to dial a digit for directory dialing. 2. Dial the letters that correspond to the name of the person you wi...
Page 1804
Issue 11.0 univerge sv8100 2 - 1772 vm8000 inmail this page intentionally left blank.
Page 1805: Vm8000 Inmail Park and Page
Univerge sv8100 issue 11.0 vm8000 inmail park and page 2 - 1773 vm8000 inmail park and page description vm8000 inmail park and page can automatically park a call at an extension and page the user with a recorded paging message announcing the parked call. The called extension user can then go to any ...
Page 1806
Issue 11.0 univerge sv8100 2 - 1774 vm8000 inmail park and page automated attendant direct to voice mail (dvm) when an extension has automated attendant direct to voice mail (dvm) enabled, all calls from the automated attendant go directly to the subscriber’s mailbox. The extension does not ring for...
Page 1807
Univerge sv8100 issue 11.0 vm8000 inmail park and page 2 - 1775 for automated attendant unscreened (utrf) and screened (strf) transfers refer to table 2-118 park and page call handling . Undefined 1 (yes) 1 (yes) if unanswered, caller can dial 1 to leave a message or 2 to park and page. Defined 0 (n...
Page 1808
Issue 11.0 univerge sv8100 2 - 1776 vm8000 inmail park and page system availability terminals all terminals required component(s) cd-cp00-us with pz-vm21 daughter board vm8000 inmail compactflash cpu license for vrs related features park paging, internal 1 (yes) 1 (imm) 0 (no) park and page occurs i...
Page 1809
Univerge sv8100 issue 11.0 vm8000 inmail park and page 2 - 1777 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards fo...
Page 1810
Issue 11.0 univerge sv8100 2 - 1778 vm8000 inmail park and page setting up park and page for a group mailbox: program number program name description/comments assigned data level 1 2 3 47-06-07 group mailbox subscriber options – auto attendant do not disturb enable/disable auto attendant direct to v...
Page 1811
Univerge sv8100 issue 11.0 vm8000 inmail park and page 2 - 1779 operation to record your paging message refer to table 2-119 recording your paging message . Table 2-119 recording your paging message recording your paging message in these instructions: [telephone softkey] to record your paging messag...
Page 1812
Issue 11.0 univerge sv8100 2 - 1780 vm8000 inmail park and page to set your call handling options refer to table 2-120 setting the call handling options . To retrieve a call parked in a personal parked orbit refer to table 2-121 picking up a parked call . Table 2-120 setting the call handling option...
Page 1813
Univerge sv8100 issue 11.0 vm8000 inmail upload download audio 2 - 1781 vm8000 inmail upload download audio description the vm8000 inmail upload download audio feature allows the upload of mailbox greetings up to 1mb in size, recorded on a pc or professionally, to any valid subscriber mailbox in the...
Page 1814
Issue 11.0 univerge sv8100 2 - 1782 vm8000 inmail upload download audio the following details the page layout diagram of the two different user pro login ids: message name format downloaded messages are automatically assigned a name by the sv8100. This name includes the mailbox number the message wa...
Page 1815
Univerge sv8100 issue 11.0 vm8000 inmail upload download audio 2 - 1783 conditions with version 3000 or lower software, uploading audio files to any type of call routing box and group mailboxes are not supported. Auto attendant and group mailbox greetings cannot be uploaded or deleted in the end use...
Page 1816
Issue 11.0 univerge sv8100 2 - 1784 vm8000 inmail upload download audio when a mailbox has a new message and the message is downloaded using the user pro interface, the mwi of the mailbox will not be cancelled. If the message is deleted from user pro the mwi is turned off. The largest allowed upload...
Page 1817
Univerge sv8100 issue 11.0 vm8000 inmail upload download audio 2 - 1785 required component(s) pz-vm21 vm8000 inmail cf cpu license related features vm8000 inmail voice response system (vrs) upload download audio guide to feature programming the level 1, level 2 and level 3 columns indicate the progr...
Page 1818
Issue 11.0 univerge sv8100 2 - 1786 vm8000 inmail upload download audio troubleshooting the table below shows possible error messages and causes: 90-02-02 programming password setup – password configure the administrator accounts that are used when connecting to the kts via pcpro/ webpro. If using p...
Page 1819
Univerge sv8100 issue 11.0 vm8000 inmail upload download audio 2 - 1787 operation listening to voice mail messages using user admin mode (ua): all messages stored on the inmail can be accessed via the mailbox user mode for playback or deletion. 1. To login, open an internet browser and enter the ip ...
Page 1820
Issue 11.0 univerge sv8100 2 - 1788 vm8000 inmail upload download audio 3. You will then see the main menu, click on the inmail audio up/download icon. The message numbers correspond to the same message number when accessed via the telephone. Message 1 is the first message, message 2 is the second m...
Page 1821
Univerge sv8100 issue 11.0 vm8000 inmail upload download audio 2 - 1789 changing mailbox greetings using mailbox user mode (ub): audio files up to 1mb may be uploaded to the inmail for any mailbox greeting. In order for uploaded greetings to play on the vm8000 they must be in the proper format. Audi...
Page 1822
Issue 11.0 univerge sv8100 2 - 1790 vm8000 inmail upload download audio this page intentionally left blank.
Page 1823: Caller Id
Univerge sv8100 issue 11.0 vm8000 inmail – automatic access to vm by caller id 2 - 1791 vm8000 inmail – automatic access to vm by caller id description before, when a user outside the system accessed their inmail mailbox, they dialed voice mail, then entered an access code followed by their mailbox ...
Page 1824
Issue 11.0 univerge sv8100 2 - 1792 vm8000 inmail – automatic access to vm by caller id conditions the vm8000 inmail – automatic access to vm by caller id (cid) feature requires version 5000 or higher software and the version 5000 enhancement license. When using this feature the inmail does not prom...
Page 1825
Univerge sv8100 issue 11.0 vm8000 inmail – automatic access to vm by caller id 2 - 1793 trunks the following trunks support sending caller id: analog line isdn line (bri) isdn line (pri) sip line h.323 line required component(s) pz-vm21 vm8000 inmail compact flash cpu license for vm related features...
Page 1826
Issue 11.0 univerge sv8100 2 - 1794 vm8000 inmail – automatic access to vm by caller id guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcp...
Page 1827
Univerge sv8100 issue 11.0 vm8000 inmail – automatic access to vm by caller id 2 - 1795 15-22-01 mobile extension setup – mobile extension target setup for each mobile extension number, select the abbreviated dial bin number to be associated with it. When using this feature with mobile extension, se...
Page 1828
Issue 11.0 univerge sv8100 2 - 1796 vm8000 inmail – automatic access to vm by caller id 22-11-05 did translation table number conversion – transfer destination number 1 for each did translation table entry (1-2000), specify the first and second transfer destinations if the callers receives a busy or...
Page 1829
Univerge sv8100 issue 11.0 vm8000 inmail – automatic access to vm by caller id 2 - 1797 operation retrieve vm messages: to retrieve vm messages from outside of office: if incoming analog trunks are used in the system main number: 214-555-5678 outside party number: 214-555-1212 program 22-02-01: trun...
Page 1830
Issue 11.0 univerge sv8100 2 - 1798 vm8000 inmail – automatic access to vm by caller id if incoming did trunks are used in the system main number: 214-555-5678 outside party number: 214-555-1212 program 22-02-01: trunk 1 did program 22-11-05: set transfer destination, 102 inmail program 13-04-01: sp...
Page 1831
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1799 vm8000 inmail – cascade message notification description if an extension user receives a new message in their mailbox, cascading message notification will call them at up to five preset destinations to let them know a n...
Page 1832
Issue 11.0 univerge sv8100 2 - 1800 vm8000 inmail – cascade message notification security: enables or disables the security code requirement for the notification destinations. For example, you may want to disable the security code when the destinations is your cell phone and it may be inconvenient t...
Page 1833
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1801 depending on the system ars routing maybe needed to properly route external calls. If no trunks are available when an outside destination is attempted it is counted as a busy no answer attempt. Cascade message notificat...
Page 1834
Issue 11.0 univerge sv8100 2 - 1802 vm8000 inmail – cascade message notification figure 2-52 cascade message notification flow chart-1.
Page 1835
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1803 figure 2-53 cascade message notification flow chart-2.
Page 1836
Issue 11.0 univerge sv8100 2 - 1804 vm8000 inmail – cascade message notification figure 2-54 cascade message notification flow chart-3.
Page 1837
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1805 message notification to normal telephone numbers this is a basic overview of how message notification works to phone numbers assuming the retry attempts are at default. The system determines which numbers are internal e...
Page 1838
Issue 11.0 univerge sv8100 2 - 1806 vm8000 inmail – cascade message notification 3. After the pager service answers, inmail waits for the timer 47-01-08 then sends the dial string in 47-01-07 which causes the pager display to show the subscriber’s mailbox number as well as the number of new messages...
Page 1839
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1807 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and ...
Page 1840
Issue 11.0 univerge sv8100 2 - 1808 vm8000 inmail – cascade message notification 47-01-09 sv8100 inmail system options – wait between digital pager callout attempts use this option to set the minimum time (1-255 minutes) between unacknowledged or unanswered digital pager message notification callout...
Page 1841
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1809 47-01-14 sv8100 inmail system options – number of cascading attempts notify call attempt with cascade pager notification: set how many times a mailboxes enabled pager notification destinations are tried. For example if ...
Page 1842
Issue 11.0 univerge sv8100 2 - 1810 vm8000 inmail – cascade message notification 47-20-01 station mailbox message notification – notification for the selected entry (1-5), use this option to enable or disable message notification. If enabled, notification will occur when the mailbox receives a new m...
Page 1843
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1811 47-20-04 station mailbox message notification – notification type for the selected entry (1-5), use this option to set the message notification type. The choices are voice and pager. Choose voice when the phone number e...
Page 1844
Issue 11.0 univerge sv8100 2 - 1812 vm8000 inmail – cascade message notification 47-20-07 station mailbox message notification – notification rna attempts for the selected entry (1-5), use this option to set how many times inmail will retry an incomplete message notification callout when the destina...
Page 1845
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1813 47-20-12 station mailbox message notification – day of week wednesday for the selected entry (1-5), use this option to enable or disable message notification on wednesday. There are five separately- programmed message n...
Page 1846
Issue 11.0 univerge sv8100 2 - 1814 vm8000 inmail – cascade message notification 47-22-02 group mailbox notification options – notification begin hour for the selected entry (1-5), use this option to set the hour when message notification will start. Notification will occur only for new messages rec...
Page 1847
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1815 47-22-05 group mailbox notification options – notification number for the selected entry (1-5), use this option to set the telephone number (16 digits maximum) message notification will dial to notify the subscriber of ...
Page 1848
Issue 11.0 univerge sv8100 2 - 1816 vm8000 inmail – cascade message notification 47-22-08 group mailbox notification options – notification security for the selected entry (1-5), use this option to enable or disable security code protection for the callout. If enabled, the user is required to enter ...
Page 1849
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1817 operation to set up cascade notification: 1. Access the all message notification setting menu. Log onto subscriber mailbox. ↓ dial op(67) / press "more >" → "setup" mailbox options menu. 47-22-13 group mailbox notificat...
Page 1850
Issue 11.0 univerge sv8100 2 - 1818 vm8000 inmail – cascade message notification ↓ dial n(6) / press "notfy" notification type selection menu. ↓ dial p(7) / press "phone" all message notifications setting menu. 2. All message notifications setting menu. ↓ dial o(6) / press "on" ↑dial o(6) / press "o...
Page 1851
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1819 3. Notification destination selection menu. ↓ press "more>" ↑press "more>" soft key operation (3-line phone/super display phone) dest1/destination1 proceed to phone notification destination 1 menu dest2/destination2 pro...
Page 1852
Issue 11.0 univerge sv8100 2 - 1820 vm8000 inmail – cascade message notification ↓ dial e(3) / press "enbl" ↑dial d(3) / press "disbl" soft key operation (3-line phone/super display phone) enbl/enable turn destination[x] notifications on disbl/disable turn destination[x] notifications off chnge/chan...
Page 1853
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1821 9. Message notification programming (security code required) soft key operation (3-line phone/super display phone) req/required turn “security code required” flag on noreq/not required turn “security code required” flag...
Page 1854
Issue 11.0 univerge sv8100 2 - 1822 vm8000 inmail – cascade message notification figure 2-55 cascade message flow chart 1.
Page 1855
Univerge sv8100 issue 11.0 vm8000 inmail – cascade message notification 2 - 1823 figure 2-56 cascade message flow chart 2.
Page 1856
Issue 11.0 univerge sv8100 2 - 1824 vm8000 inmail – cascade message notification this page intentionally left blank.
Page 1857
Univerge sv8100 issue 11.0 vm8000 inmail – email notification 2 - 1825 vm8000 inmail – email notification description email notification automatically sends an email notification when a subscriber mailbox receives a new message. The email can optionally include the recorded message as a .Wav file at...
Page 1858
Issue 11.0 univerge sv8100 2 - 1826 vm8000 inmail – email notification explanation of the message sender (from) field like any other email client, email notification uses the from field to identify the person that left the message being delivered. In the email message, the data in the from field is ...
Page 1859
Univerge sv8100 issue 11.0 vm8000 inmail – email notification 2 - 1827 reply to 4 is: the email address of the person that left the message (if programmed). - or - the reply to email address data from program 47-18-09. - or - the send from email address data from program 47-18-09. For messages left ...
Page 1860
Issue 11.0 univerge sv8100 2 - 1828 vm8000 inmail – email notification pop3 login vm8000 inmail email notification supports pop3 login. The logic of this method is that it allows a user to send e-mail from any location, as long as they can demonstrably also fetch their mail from the same place. Chec...
Page 1861
Univerge sv8100 issue 11.0 vm8000 inmail – email notification 2 - 1829 some common sms portals conditions sv8100 software version 3000 or higher is required to support this feature. A pz-me50-us must be mounted on the cd-cp00-us to support this feature. The email notification feature (1014) is licen...
Page 1862
Issue 11.0 univerge sv8100 2 - 1830 vm8000 inmail – email notification email notification options can only be changed from webpro, pcpro or system programming for group subscriber mailboxes. Email notification options can only be changed from userpro, webpro, pcpro or system programming for station ...
Page 1863
Univerge sv8100 issue 11.0 vm8000 inmail – email notification 2 - 1831 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wiz...
Page 1864
Issue 11.0 univerge sv8100 2 - 1832 vm8000 inmail – email notification 47-06-25 group mailbox subscriber options – email message save/ delete option when email notification is enabled, use this option to set how notification handles new voice mail message content. If no change is selected, the messa...
Page 1865
Univerge sv8100 issue 11.0 vm8000 inmail – email notification 2 - 1833 operation refer to the vm8000 inmail system guide for more information about this feature. 47-19-02 vm8000 inmail pop3 setup – pop3 port set the pop3 server port. 0~65535 (default = 110) 47-19-03 vm8000 inmail pop3 setup – ssl en...
Page 1866
Issue 11.0 univerge sv8100 2 - 1834 vm8000 inmail – email notification this page intentionally left blank.
Page 1867
Univerge sv8100 issue 11.0 vm8000 inmail – find-me follow-me 2 - 1835 vm8000 inmail – find-me follow-me description find-me follow-me helps an outside caller locate an extension user who is not at their desk. If their call is unanswered and is picked up by voice mail, the caller has the option of di...
Page 1868
Issue 11.0 univerge sv8100 2 - 1836 vm8000 inmail – find-me follow-me you can set up find-me follow-me for an extension in system programming. In addition, an extension user can set up find-me follow-me from their mailbox options. Conditions main software version 4000 or higher is required to suppor...
Page 1869
Univerge sv8100 issue 11.0 vm8000 inmail – find-me follow-me 2 - 1837 required component(s) none related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used....
Page 1870
Issue 11.0 univerge sv8100 2 - 1838 vm8000 inmail – find-me follow-me 47-21-01 station mailbox find-me follow- me options – find-me follow-me use this option to enable or disable a find-me follow-me destination. If enabled, find-me follow-me will occur according to the settings for start hour, end h...
Page 1871
Univerge sv8100 issue 11.0 vm8000 inmail – find-me follow-me 2 - 1839 47-21-07 station mailbox find-me follow-me options – day of week tuesday for the selected entry (1-5), use this option to enable or disable find-me follow-me on tuesday. There are three separately- programmed find-me follow-me ent...
Page 1872
Issue 11.0 univerge sv8100 2 - 1840 vm8000 inmail – find-me follow-me 47-23-02 group mailbox find-me follow-me options – find-me follow-me begin hour use this option to set the hour when find-me follow-me will start. Find-me follow-me will occur only between this setting and the end hour setting. 0-...
Page 1873
Univerge sv8100 issue 11.0 vm8000 inmail – find-me follow-me 2 - 1841 47-23-08 group mailbox find-me follow-me options – day of week wednesday for the selected entry (1-5), use this option to enable or disable find-me follow-me on wednesday. There are three separately- programmed find-me follow-me e...
Page 1874
Issue 11.0 univerge sv8100 2 - 1842 vm8000 inmail – find-me follow-me operation setting up message notification log on to subscriber mailbox. Op (67) access the mailbox options menu. [not applicable] n (6) access the message notification options menu. [notif] vm8000 inmail plays a summary of your me...
Page 1875
Univerge sv8100 issue 11.0 vm8000 inmail – find-me follow-me 2 - 1843 * skip this option without changing your entry. [next] # back up to the previous level without changing your entry. [exit] when you see: notify via n (6) the notification destination is a telephone number. [num] d (3) the notifica...
Page 1876
Issue 11.0 univerge sv8100 2 - 1844 vm8000 inmail – find-me follow-me this page intentionally left blank.
Page 1877
Univerge sv8100 issue 11.0 vm8000 inmail – language setting 2 - 1845 vm8000 inmail – language setting description the language setting feature allows the telephone display language and the inmail mailbox language to be changed from the telephone. This can be used to change either the user’s phone or...
Page 1878
Issue 11.0 univerge sv8100 2 - 1846 vm8000 inmail – language setting 08 (italian) 09 (german) 10 (madrid spanish) 11 (norwegian) 12 (parisian french) 13 (brazilian portuguese) 14 (japanese) 15 (mandarin chinese) 16 (korean) 17 (iberian portuguese) 18 (greek) 19 (danish) 20 (swedish) 21 (thai) 22 (ta...
Page 1879
Univerge sv8100 issue 11.0 vm8000 inmail – language setting 2 - 1847 related features none guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with ...
Page 1880
Issue 11.0 univerge sv8100 2 - 1848 vm8000 inmail – language setting operation 40-07-01 voice prompt language assignment for vrs specify the language to be used for the inmail prompts. 1 = us english 2 = uk english 3 = au english 4 = ca french 5 = dutch 6 = mex spanish 7 = la spanish 8 = italian 9 =...
Page 1881
Univerge sv8100 issue 11.0 vm8000 inmail – language setting 2 - 1849 table 2-129 language setting operation from an idle display phone press down arrow prog press program softkey press down arrow press down arrow lang press language softkey disp to change telephone display language press display sof...
Page 1882
Issue 11.0 univerge sv8100 2 - 1850 vm8000 inmail – language setting this page intentionally left blank.
Page 1883: Voice Call Recording
Univerge sv8100 issue 11.0 voice call recording 2 - 1851 voice call recording description when using nec dt 300 and dt 700 desktop terminals, telephone calls can be monitored, recorded and stored. For dt 300 (tdm) terminals, the nec 4-port digital call logging unit – vsr (voice security recorder) is...
Page 1884
Issue 11.0 univerge sv8100 2 - 1852 voice call recording the second player option is the vsr manager. Take your call recording environment to the next level with nec vsr application software. Vsr manager provides advanced visibility, access, retrieval, and playback tools for the vsr recorder adminis...
Page 1885
Univerge sv8100 issue 11.0 voice call recording 2 - 1853 system availability terminals nec dt300/dt700 series desktop terminals – d term ® voice security recorder (vsr) required component(s) 4-port digital call logging unit pc hardware and software: 4-port digital call logging unit pentium 4 process...
Page 1886
Issue 11.0 univerge sv8100 2 - 1854 voice call recording guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featu...
Page 1887
Univerge sv8100 issue 11.0 voice call recording 2 - 1855 operation refer to the univerge sv8100 system hardware manual, chapter 11, section 11 d term ® voice security recorder (vsr) for detailed information. Nec sonicview ™ ip recorder (1.0) description the nec sonicview ™ ip recorder application is...
Page 1888
Issue 11.0 univerge sv8100 2 - 1856 voice call recording refer to the nec ip recorder sonicview user guide and installation manual located on the ak system pc apps cd (p/n 670830) for additional information. Recording engine the sonicview application uses the recording engine component to sniff and ...
Page 1889
Univerge sv8100 issue 11.0 voice call recording 2 - 1857 nec ip recorder sonic view - a vista “master administrator” account (“administrator”) is required to install the application. The user must enable the vista master administrator account and log into this account to perform the installation. Th...
Page 1890
Issue 11.0 univerge sv8100 2 - 1858 voice call recording recording server requirements hardware: pentium 1.6 ghz core 2 duo a minimum of 2 gb ram 250 gb of free hard disk space (30000 hours of continuous recording) svga monitor 1024 x 768 resolution network interface card (nic) supported operating s...
Page 1891
Univerge sv8100 issue 11.0 voice call recording 2 - 1859 supported internet browsers: microsoft internet explorer 7 and above mozilla ® firefox ® version 2.0 or above google ™ chrome sv8100 cpu license (nec ip recorder sonicview) related features none table 2-130 ip recorder basic licenses 670863 lk...
Page 1892
Issue 11.0 univerge sv8100 2 - 1860 voice call recording guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featu...
Page 1893
Univerge sv8100 issue 11.0 voice call recording 2 - 1861 operation refer to the sonicview user guide for operational details. Refer to the following manuals for detailed information regarding the nec sonicview ip recorder: nec sonicview ip recorder installation and setup guide nec sonicview ip recor...
Page 1894
Issue 11.0 univerge sv8100 2 - 1862 voice call recording database server the sonicview application uses postgresql server as the database server for storing all the call information captured from the network. The postgresql database server can be implemented in a straightforward manner as a separate...
Page 1895
Univerge sv8100 issue 11.0 voice call recording 2 - 1863 conditions if nec sonic view ip recorder 1.0 has been installed previously, then the sonicview ip recorder 1.0 must be uninstalled prior to installing nec sonicview recorder 2.0. The pc hosting the recording engine component should be on the s...
Page 1896
Issue 11.0 univerge sv8100 2 - 1864 voice call recording required component(s) only application hardware: pentium 1.8 ghz core 2 duo or above a minimum of 4 gb ram 250 gb of free hard disk space (30000 hours of continuous recording) svga monitor 1024 x 768 resolution network interface card (nic) sup...
Page 1897
Univerge sv8100 issue 11.0 voice call recording 2 - 1865 a minimum of 1 gb ram svga monitor 1024 x 768 resolution adobe flash player plug-in version 10 or above adobe acrobat reader 7 or above (if client needs to view\edit reports) microsoft excel 2000 (if client needs to view\edit reports) supporte...
Page 1898
Issue 11.0 univerge sv8100 2 - 1866 voice call recording guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featu...
Page 1899
Univerge sv8100 issue 11.0 voice call recording 2 - 1867 operation refer to the sonicview user guide for operational details. Refer to the following manuals for detailed information regarding the nec sonicview recorder: nec sonicview recorder installation and setup manual nec sonicview recorder appl...
Page 1900
Issue 11.0 univerge sv8100 2 - 1868 voice call recording 3 known limitations of the solution 3.1 outbound and internal calls are recorded even if the called party does not answer the call. Such recordings include the dtmf tones as well as the phone ringing activities. For example, if a call is estab...
Page 1901
Univerge sv8100 issue 11.0 voice call recording 2 - 1869 3.7 configure license server tool to modify pbx ip address, port, mac address, web server ip address & port will not support modifying the web server ip address & port. Known issues with modifying the web server ip address & port from configur...
Page 1902
Issue 11.0 univerge sv8100 2 - 1870 voice call recording 3.18 advanced ‘player controls’: the transport controls in media player in the application do not work as intended for short duration call recordings. The rewind, forward, pause controls and dragging the slider may cause the stream to stop pla...
Page 1903
Univerge sv8100 issue 11.0 voice call recording 2 - 1871 3.29 digital recorder: recordings details for tdm/digital extensions will not show the call direction. For example, if a you have a tdm/digital extension 101 that was part of an outbound/inbound/internal call then the call details are shown as...
Page 1904
Issue 11.0 univerge sv8100 2 - 1872 voice call recording default settings not installed system availability terminals nec dt700 series (ip) terminals – nec sonicview hybrid recorder nec dt300 series (digital) terminals- nec sonicview hybrid recorder required component(s) ensure the following hardwar...
Page 1905
Univerge sv8100 issue 11.0 voice call recording 2 - 1873 minimum system requirements hardware server: table 2-133 system minimum requirements recording capacity server hardware specifications (see note 1) recommended operating systems (see note 2) up to 40 stations 1 1, 2, 3, 4, 5 up to 100 stations...
Page 1906
Issue 11.0 univerge sv8100 2 - 1874 voice call recording common: nics (2 required): one (1) network interface card (nic) is sufficient provided the managed switch performing port mirroring supports both ingress and egress traffic on the mirrored port. Two (2) network interface cards (nic) are requir...
Page 1907
Univerge sv8100 issue 11.0 voice call recording 2 - 1875 operating system: database: monitor display svga monitor 1024 x 768 resolution software requirements adobe flash player plug-in version 10 or above adobe acrobat reader 7 or above (to view pdf reports) microsoft© excel 2000 (to view\edit repor...
Page 1908
Issue 11.0 univerge sv8100 2 - 1876 voice call recording related features none table 2-139 sv8100 cpu license (nec sonicview recorder) 670863 lks-recorder basic pkg-lic feature code quantity included comments 3200 4 stations 1 supervisor 4 odrs (on-demand recording) provides the ability to have four...
Page 1909
Univerge sv8100 issue 11.0 voice call recording 2 - 1877 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featu...
Page 1910
Issue 11.0 univerge sv8100 2 - 1878 voice call recording operation refer to the sonicview user guide for operational details. Refer to the following manuals for detailed information regarding the nec sonicview recorder: nec sonicview recorder installation and setup manual nec sonicview recorder appl...
Page 1911
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1879 voice mail integration (analog) description the system provides telephone users with comprehensive voice mail features. Voice mail ends the frustration and cost of missed calls, inaccurate written messages and telephone tag. This fr...
Page 1912
Issue 11.0 univerge sv8100 2 - 1880 voice mail integration (analog) msg key will operate as voice mail key the system enhances a telephone msg key function when connected to a system which has voice mail installed. When an extension receives a voice mail, the msg key can be used to check the number ...
Page 1913
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1881 conditions the periodic reminder message requires a dsp daughter board for voice response system (vrs). Ring group calls do not follow extension call forwarding to voice mail. Only one voice mail system can be installed in an sv8100...
Page 1914
Issue 11.0 univerge sv8100 2 - 1882 voice mail integration (analog) default setting disabled system availability terminals all terminals required component(s) cd-4lca (4-port main blade) pz-4lca (4-port daughter board) cd-8lca (8-port main blade) pz-8lce (8-port daughter board) related features barg...
Page 1915
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1883 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizard...
Page 1916
Issue 11.0 univerge sv8100 2 - 1884 voice mail integration (analog) 15-02-35 multiline telephone basic data setup – message waiting lamp cycle for calling extension select the message waiting flash pattern for the station that set the message waiting reminder. 1 = cycle 1 2 = cycle 2 3 = cycle 3 4 =...
Page 1917
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1885 15-07-01 programmable function keys assign a voice mail key to an extension. You must enter the voice mail key code (code 77) followed by: your own extension number if you are setting up your own voice mail key. A virtual extension ...
Page 1918
Issue 11.0 univerge sv8100 2 - 1886 voice mail integration (analog) 16-01-04 department group basic data setup – hunting mode set the action taken when a call reaches the last extension in the department group. Hunting is stopped or circular search continues. 0 = last extension is called and hunting...
Page 1919
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1887 20-03-01 system options for single line telephones – slt call waiting answer mode for a busy single line (500/2500) telephone, set the mode used to answer a camped-on trunk call. The default setting should be used. 0 = hookflash (ho...
Page 1920
Issue 11.0 univerge sv8100 2 - 1888 voice mail integration (analog) 20-13-03 class of service options (supplementary service) – long conversation cutoff (outgoing) turn off or on an extension user ability to use long conversation cutoff for outgoing calls. 0 = off 1 = on (default = 0 for cos 1~15) 2...
Page 1921
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1889 22-02-01 incoming call trunk setup – incoming type assign the incoming trunk type for each trunk. There is one item for each mode. When using trunk-to-trunk forwarding the trunk must be set to 0. 0 = normal 1 = vrs (second dial tone...
Page 1922
Issue 11.0 univerge sv8100 2 - 1890 voice mail integration (analog) 40-07-01 voice prompt language assignment for vrs specify the language to be used for the vrs prompts. 1 = us english 2 = uk english 3 = au english 4 = ca french 5 = dutch 6 = mex spanish 7 = la spanish 8 = italian 9 = german 10 = e...
Page 1923
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1891 45-01-05 voice mail integration options – message wait turn off or on the system ability to process the voice mail message wait ( # ) commands. You should normally enable this option. If enabled, be sure that the programmed message ...
Page 1924
Issue 11.0 univerge sv8100 2 - 1892 voice mail integration (analog) 45-04-09 voice mail digit add assignment – clear down string define the digits for clear down string. Up to four digits (default = none) 45-05-01 voice mail send protocol signal without additional digits – remote log-on internal sen...
Page 1925
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1893 80-03-01 dtmf tone receiver setup – detect level define the detect level for dtmf tone receiver. 0 = 0dbm ~ -25dbm 1 = -5dbm ~ -30dbm 2 = -10dbm ~ -35dbm 3 = -15dbm ~ -40dbm 4 = -20dbm ~ -45dbm 5 = -25dbm ~ -50dbm 6 = -30dbm ~ -55db...
Page 1926
Issue 11.0 univerge sv8100 2 - 1894 voice mail integration (analog) 80-03-03 dtmf tone receiver setup – min. Detect level define the various minimum detect levels for the dtmf tone receiver. 0~15 detect level 0: –10dbm(0) to –25dbm(15) detect level 1: –15dbm(0) to – 30dbm(15) detect level 2: –20dbm(...
Page 1927
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1895 80-03-04 dtmf tone receiver setup – max. Detect level define the various maximum detect levels for the dtmf tone receiver. 0~15 detect level 0: 0dbm(0) to –15dbm(15) detect level 1: –5dbm(0) to – 20dbm(15) detect level 2: –10dbm(0) ...
Page 1928
Issue 11.0 univerge sv8100 2 - 1896 voice mail integration (analog) 80-03-05 dtmf tone receiver setup – forward twist level define the various forward twist levels for the dtmf tone receiver. 0~9 (1db~10db) [default: type 1~5 = 5 (6dbm)] 80-03-06 dtmf tone receiver setup – backward twist level defin...
Page 1929
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1897 80-04-03 call progress tone detector setup – s/n ratio define the s/n ratio for the call progress tone detector. 0~4 (0db ~ -20db) default: type 1 (dt) – 4 (-20db) type 2 (bt) – 4 (-20db) type 3 (rbt) – 4 (-20db) type 4, type 5 – 0 ...
Page 1930
Issue 11.0 univerge sv8100 2 - 1898 voice mail integration (analog) 80-04-07 call progress tone detector setup – on maximum time define the on maximum time for the call progress tone detector. 0~255 (30+30-7680ms) default: type 1 (dt) – 0 type 2 (bt) – 20 (450ms) type 3 (rbt) – 40 1230ms) type 4, ty...
Page 1931
Univerge sv8100 issue 11.0 voice mail integration (analog) 2 - 1899 operation calling your mailbox: to call your mailbox: multiline terminal 1. Press your voice mail key (program 15-07 or sc 751: 77) or the message key. - or - press speaker and dial the voice mail master number. After voice mail ans...
Page 1932
Issue 11.0 univerge sv8100 2 - 1900 voice mail integration (analog) recording your call: to record your active call in your mailbox: multiline terminal 1. Press voice mail record key (program 15-07 or sc 751: code 78). You hear two beeps and your record key flashes. The beeps periodically repeat to ...
Page 1933
Univerge sv8100 issue 11.0 voice mail message indication on line keys 2 - 1901 voice mail message indication on line keys description voice mail message indication on line keys indicates a new voice mail message on line keys or dss/ blf keys. Conditions when a dss key of an installed extension is pr...
Page 1934
Issue 11.0 univerge sv8100 2 - 1902 voice mail message indication on line keys related features class of service direct station selection (dss) console programmable function keys um8000 mail vm8000 inmail voice mail integration (analog) guide to feature programming the level 1, level 2 and level 3 c...
Page 1935
Univerge sv8100 issue 11.0 voice mail message indication on line keys 2 - 1903 30-02-01 dss console extension assignment – extension number enter the extension number for the multiline terminal connected with the dss console (up to eight digits). Up to eight digits. (default not assigned) 30-03-01 d...
Page 1936
Issue 11.0 univerge sv8100 2 - 1904 voice mail message indication on line keys operation to program a dss/blf key on a telephone: 1. Press speaker. 2. Dial 751. 3. Press the key you want to program. 4. Dial 01. 5. Dial the number of the extension you want to appear on the key. 30-05-12 dss console l...
Page 1937
Univerge sv8100 issue 11.0 voice mail message indication on line keys 2 - 1905 6. Press hold. 7. Press speaker. To program a vm message key on a telephone: 1. Press speaker. 2. Dial 751. 3. Press the key you want to program. 4. Dial 77. 5. Dial the number of the extension you want to appear on the k...
Page 1938
Issue 11.0 univerge sv8100 2 - 1906 voice mail message indication on line keys this page intentionally left blank.
Page 1939: Voice Over
Univerge sv8100 issue 11.0 voice over 2 - 1907 voice over description voice over lets a user interrupt a busy station user that is on another call. With voice over, the busy extension user hears an alert tone followed by the voice of the interrupting party. The extension user receiving the voice ove...
Page 1940
Issue 11.0 univerge sv8100 2 - 1908 voice over when a programmable function key (programmed with the voice over access code) is pressed, the led lights while responding to the page. When a multiline terminal has a handsfree unit programmed, the voice over call can be received and answered handsfree....
Page 1941
Univerge sv8100 issue 11.0 voice over 2 - 1909 related features conference off-hook signaling programmable function keys guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly use...
Page 1942
Issue 11.0 univerge sv8100 2 - 1910 voice over operation to initiate a voice over to a busy extension: 1. Press voice over key (program 15-07 or sc 751: 48) - or - dial 6. - or - dial 690. You hear an alert tone and the voice over key flashes. You can talk to the called party after the alert tone en...
Page 1943: Voice Response System (Vrs)
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1911 voice response system (vrs) description the pz-vm21 daughter board provides the option for the voice response system (vrs) which gives the system voice recording and playback ability. The vrs compactflash card provides up to 100 system ...
Page 1944
Issue 11.0 univerge sv8100 2 - 1912 voice response system (vrs) general message a general message is a recorded message available to all callers. A general message typically contains important company information that all employees should hear. To hear the general message, an employee can go to any ...
Page 1945
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1913 automatic overflow automatic overflow can automatically redirect a call if it cannot go through. This can happen if all vrs ports are busy, if the called extension does not answer, or if the caller misdials or waits too long to dial. (t...
Page 1946
Issue 11.0 univerge sv8100 2 - 1914 voice response system (vrs) the following programs are used to define the vrs waiting message feature and the trunk overflow: 11-10-20: service code setup (for system administrator) – vrs - record/erase message 15-07: programmable function keys automatic answer wi...
Page 1947
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1915 the following table shows the available voice prompting messages. Table 2-140 voice prompting messages message no. Message this message will play when . . . 1-00 this is station a user dials 6 for the extension number. 1-01 station a us...
Page 1948
Issue 11.0 univerge sv8100 2 - 1916 voice response system (vrs) 1-19 enter your area code and telephone number an outside caller dials an extension through the automated attendant and the extension is busy. 1-20 please enter your password 1-21 please enter an account code a user tries to place a tru...
Page 1949
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1917 2-05 one a user dials 6 for the extension number, 8 for the time and date or as part of a spoken code (e.G., 714). 2-06 two 2-07 three 2-08 four 2-09 five 2-10 six 2-11 seven 2-12 eight 2-13 nine 2-14 ten 2-15 eleven 2-16 twelve 2-17 th...
Page 1950
Issue 11.0 univerge sv8100 2 - 1918 voice response system (vrs) 2-33 thousand 2-43 message 2-44 messages 2-64 january 2-65 february 2-66 march 2-67 april 2-68 may 2-69 june 2-70 july 2-71 august 2-72 september 2-73 october 2-74 november 2-75 december 2-76 sunday a user dials 8 for the date. 2-77 mon...
Page 1951
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1919 900 preamble if the system has trunks that are part of a 900 (caller paid) service, the vrs can automatically play a recorded message when a user answers the call. This recorded message should describe the 900 service features and cost....
Page 1952
Issue 11.0 univerge sv8100 2 - 1920 voice response system (vrs) the number of speech path channels on the cd-cp00-us (cpu) for the vm8000 (in mail) and the vrs feature are shared and depends if the pz-me50 daughter board is installed. Without a pz-me50 daughter board installed the systems supports a...
Page 1953
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1921 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards fo...
Page 1954
Issue 11.0 univerge sv8100 2 - 1922 voice response system (vrs) 20-07-13 class of service options (administrator level) – vrs record (vrs msg operation) turn off or on an extension user ability to record, listen to, or erase vrs messages. 0 = off 1 = on (default = 0 for cos 1~14) (default = 1 for co...
Page 1955
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1923 22-02-01 incoming call trunk setup for each night service mode, enter 1 if trunk should be automatically answered by vrs automated attendant. Trunks 1~200 0 = normal 1 = vrs (second dial tone if no vrs installed) 2 = disa 3 = did 4 = di...
Page 1956
Issue 11.0 univerge sv8100 2 - 1924 voice response system (vrs) 22-14-06 vrs delayed message for irg – tone kind at message interval for each ring group, determine what the caller hears between messages. This program is also used for vrs waiting message. 0 = ring back tone 1 = moh tone 2 = bgm sourc...
Page 1957
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1925 22-15-07 vrs delayed message for department group – disconnect time after the end of vrs delayed message for each department group, set the time the system waits after playing the vrs message before disconnecting the call. To prevent th...
Page 1958
Issue 11.0 univerge sv8100 2 - 1926 voice response system (vrs) 25-04-01 vrs/disa transfer ring group with no answer/busy set the destination that automated attendant (opa) calls ring if the opa caller dials an extension that does not answer or is busy. This also sets the options for disa calls. The...
Page 1959
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1927 25-07-02 system timers for vrs/disa – vrs/disa no answer time if an automated attendant caller dials an extension that does not answer, the call waits this time before rerouting to the ring group specified in program 25-03 and program 2...
Page 1960
Issue 11.0 univerge sv8100 2 - 1928 voice response system (vrs) 31-04-01 external paging zone group – paging group number assign each external paging zone to an external paging group. 0~8 (0 = no setting) default: speaker 1 [pgd(2)- u10] = 1 (group 1) speaker 2 [pgd(2)- u10] = 2 (group 2) speaker 3 ...
Page 1961
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1929 40-07-01 voice prompt language assignment for vrs select the language to be used for the vrs. Although the system allows this option to be changed in programming, the language changes only if the pz-vm21 has the firmware which provides ...
Page 1962
Issue 11.0 univerge sv8100 2 - 1930 voice response system (vrs) operation vrs messages: to record a vrs message: 1. Press speaker or lift the handset. - or - at a single line telephone, lift the handset. 2. Dial 616. 3. Dial 7 ( r ecord). 4. Dial the vrs message number you want to record (01~100). 5...
Page 1963
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1931 6. Press # to end recording. - or - hang up to save the message. To listen to a previously recorded vrs message: 1. Press speaker or lift the handset. - or - at a single line telephone, lift the handset. 2. Dial 616. 3. Dial 5 ( l isten...
Page 1964
Issue 11.0 univerge sv8100 2 - 1932 voice response system (vrs) to record, listen to or erase a vrs message if you call in using disa: 1. Place call to the system. You hear dial tone. 2. After the system answers, dial the disa password (normally 000000). You hear dial tone. 3. Dial 616 and the vrs p...
Page 1965
Univerge sv8100 issue 11.0 voice response system (vrs) 2 - 1933 3. Dial the function you want. 7 = r ecord 5 = l isten 3 = e rase if you dialed 7 to record, press # to end the recording. If you dialed 5 to listen, you can dial 5 to listen to the message again. To record the general message again, go...
Page 1966
Issue 11.0 univerge sv8100 2 - 1934 voice response system (vrs) this page intentionally left blank.
Page 1967
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1935 voice response system (vrs) embedded vrs description embedded vrs provides one channel of vrs without having the pz-vm21 (vmdb) and compactflash installed on the cpu, therefore allowing the voice prompt to be saved on flash...
Page 1968
Issue 11.0 univerge sv8100 2 - 1936 voice response system (vrs) embedded vrs when all 10 messages have been recorded or if all eight minutes of the recording time has been used, auto attendant callers will be dropped without notification when trying to leave a message. The following full vrs feature...
Page 1969
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1937 installing language prompt sets the procedure to load a language prompt set is similar to upgrading the system software. The same usb memory used for system software upgrades should be used. Before extracting the language p...
Page 1970
Issue 11.0 univerge sv8100 2 - 1938 voice response system (vrs) embedded vrs the following dial options will be used: message 1: day main greeting and has the following dial options: 3 = routes callers to message 3 which is used for office hours and direction information in the day mode. 4 = allows ...
Page 1971
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1939 1. Set program 22-02-01 to 1 (vrs) for trunks 1-8 in mode 1 and 2. 2. Set program 40-10-01 (vrs fixed messaging) to 1 (enable). Figure 2-57 program 22-02: incoming call trunk setup figure 2-58 program 40-10: voice announcem...
Page 1972
Issue 11.0 univerge sv8100 2 - 1940 voice response system (vrs) embedded vrs 3. For trunks 1~8 set program 25-02-01 mode 1 to message 1 (day) and mode 2 to message 2 (night). Make sure this is set this for all trunks that were set to ‘vrs” in program 22-02-01. 4. Set the dial options for message 1 (...
Page 1973
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1941 5. Set the dial options for message 2 (night main greeting) as shown below. 6. Set the dial options for message 3 (day informational greeting) as shown below. Figure 2-61 program 25-06: vrs/disa 1-digit code attendant setup...
Page 1974
Issue 11.0 univerge sv8100 2 - 1942 voice response system (vrs) embedded vrs 7. Set the dial options for message 4 (night informational greeting) as shown below. 8. Record greetings 1-4 making sure to record the dialing options as listed for each greeting. See operation section below for message rec...
Page 1975
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1943 automatic call distribution (acd) call forwarding voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in th...
Page 1976
Issue 11.0 univerge sv8100 2 - 1944 voice response system (vrs) embedded vrs 22-02-01 incoming call trunk setup for each night service mode and each trunk, enter 1 if trunk should be automatically answered by vrs automated attendant. Trunks 1~200 0 = normal 1 = vrs (second dial tone if no vrs instal...
Page 1977
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1945 operation vrs messages: to record a vrs message: 1. Press speaker or lift the handset. -or- at a single line telephone, lift the handset. 2. Dial 616. 3. Dial 7 (record). 4. Dial the vrs message number you want to record (0...
Page 1978
Issue 11.0 univerge sv8100 2 - 1946 voice response system (vrs) embedded vrs 5. When you hear, “start recording at the tone and press the pound key when you are done” followed by a beep, record your message. 6. Press # to end recording. -or- hang up to save the message. To listen to a previously rec...
Page 1979
Univerge sv8100 issue 11.0 voice response system (vrs) embedded vrs 2 - 1947 to listen to a message left by an outside caller: 1. Press speaker or lift the handset. -or- at a single line telephone, lift the handset. 2. Dial 616. 3. Dial 5 (listen). 4. Dial the vrs message number to which you want to...
Page 1980
Issue 11.0 univerge sv8100 2 - 1948 voice response system (vrs) embedded vrs this page intentionally left blank.
Page 1981: Audio
Univerge sv8100 issue 11.0 voice response system (vrs) upload download audio 2 - 1949 voice response system (vrs) upload download audio description the voice response system (vrs) upload download audio feature allows the upload of vrs greetings up to 1mb in size, recorded on a pc or professionally, ...
Page 1982
Issue 11.0 univerge sv8100 2 - 1950 voice response system (vrs) upload download audio user mode (ub mode): this mode allows a user to access only their own telephone and mailbox when logged in. They will not be able to change any other telephone, mailbox, vrs or routing mailbox. At default the login...
Page 1983
Univerge sv8100 issue 11.0 voice response system (vrs) upload download audio 2 - 1951 conditions with version 3000 or lower software, uploading audio files to any type of call routing box and group mailboxes are not supported. Auto attendant and group mailbox greetings cannot be uploaded or deleted ...
Page 1984
Issue 11.0 univerge sv8100 2 - 1952 voice response system (vrs) upload download audio when downloading/deleting an audio file via user pro, the file is not accessible by another user pro session or from the telephone. This feature is only supported using a lan connection. When uploading an audio fil...
Page 1985
Univerge sv8100 issue 11.0 voice response system (vrs) upload download audio 2 - 1953 system availability terminals all terminals required component(s) pz-vm21 vm8000 inmail cf cpu license related features voice response system (vrs) guide to feature programming the level 1, level 2 and level 3 colu...
Page 1986
Issue 11.0 univerge sv8100 2 - 1954 voice response system (vrs) upload download audio troubleshooting the table below shows possible error messages and causes: 90-02-02 programming password setup – password configure the administrator accounts that are used when connecting to the kts via pcpro/ webp...
Page 1987
Univerge sv8100 issue 11.0 voice response system (vrs) upload download audio 2 - 1955 operation changing vrs messages using user admin mode (ua): audio files up to 1mb may be uploaded to the sv8100 for vrs messages. All 100 vrs messages can be uploaded or deleted. The messages can be used on all vrs...
Page 1988
Issue 11.0 univerge sv8100 2 - 1956 voice response system (vrs) upload download audio 6. To upload a message: under message no, enter the message number to be replaced. Browse to find the location where the greeting file is stored. Click on the upload icon to the right of the selected file name. Dep...
Page 1989: Park and Page
Univerge sv8100 issue 11.0 voice response system (vrs) – call forwarding – park and page 2 - 1957 voice response system (vrs) – call forwarding – park and page description when an extension user is away from their phone, vrs park and page can let them know when they have a call waiting to be answere...
Page 1990
Issue 11.0 univerge sv8100 2 - 1958 voice response system (vrs) – call forwarding – park and page conditions vrs park and page announcements only repeat once. Voice announcement (vau) recording time is fixed at two minutes and cannot be changed. While vrs park and page is enabled, only one did call ...
Page 1991
Univerge sv8100 issue 11.0 voice response system (vrs) – call forwarding – park and page 2 - 1959 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are use...
Page 1992
Issue 11.0 univerge sv8100 2 - 1960 voice response system (vrs) – call forwarding – park and page 31-04-01 external paging zone group – paging group number assign each external paging speaker to an external paging zone. Paging group number 0~8 (0 = no setting) speaker 1 [pgd(2)-u10 adp] = 1 (group 1...
Page 1993
Univerge sv8100 issue 11.0 voice response system (vrs) – call forwarding – park and page 2 - 1961 operation to have the system page you when you have a call: 1. Press speaker (or lift the handset at the single line telephone) and dial 713. 2. When you hear, “please start recording,” record your pers...
Page 1994
Issue 11.0 univerge sv8100 2 - 1962 voice response system (vrs) – call forwarding – park and page this page intentionally left blank.
Page 1995: Volume Controls
Univerge sv8100 issue 11.0 volume controls 2 - 1963 volume controls description each multiline terminal user can control the volume of incoming ringing, splash tone, paging, background music, handsfree and your handset. Multiline terminals consolidate all adjustments into the volume buttons. Press t...
Page 1996
Issue 11.0 univerge sv8100 2 - 1964 volume controls default setting enabled system availability terminals all multiline terminals required component(s) none related features electra elite ipk terminals sv8100/sv8300 terminals off-hook signaling.
Page 1997
Univerge sv8100 issue 11.0 volume controls 2 - 1965 guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for feature pr...
Page 1998
Issue 11.0 univerge sv8100 2 - 1966 volume controls this page intentionally left blank.
Page 1999
Warning tone for long conversation 2 - 1967 w warning tone for long conversation description the system can broadcast warning tones to a trunk caller, warning the caller that he has been on the call too long. If he chooses, the caller can disregard the tones and continue talking. The outside caller ...
Page 2000
Issue 11.0 univerge sv8100 2 - 1968 warning tone for long conversation default setting disabled related features central office calls, answering central office calls, placing direct inward system access (disa) intercom long conversation cutoff single line telephones, analog 500/2500 sets code restri...
Page 2001
Univerge sv8100 issue 11.0 warning tone for long conversation 2 - 1969 20-06-01 class of service for extensions assign a class of service (1~15) to an extension. Day/night mode: 1~8 class of service for extensions: 1~15 defaults: extension number 101 as class 15. All other extension numbers are set ...
Page 2002
Issue 11.0 univerge sv8100 2 - 1970 warning tone for long conversation operation warning tone for long conversation is automatic if programmed. Warning tone for long conversation for disa callers: 1. A disa caller dials into the system and places a call. 2. After the warning tone is heard, to contin...
Page 2003: Wireless Dect (Sip)
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1971 wireless dect (sip) description the wireless dect (sip) (digital enhanced cordless telecommunication) system allows using dect 6.0 dect (sip) handsets. These handsets provide the freedom and convenience of a wireless telephone but also allow ac...
Page 2004
Issue 11.0 univerge sv8100 2 - 1972 wireless dect (sip) caller id yes only on isdn or sip trunks. Analog caller id is not supported. Data line security yes barge-in is not supported. Door box yes door box will not ring ip dect handset. Ip dect handset can call doorbox, but cannot activate the relay....
Page 2005
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1973 central office calls, placing yes class of service yes code restriction yes code restriction override yes code restriction, dial block yes dialing number preview yes direct inward dialing (did) yes direct inward line (dil) yes direct inward sys...
Page 2006
Issue 11.0 univerge sv8100 2 - 1974 wireless dect (sip) multiple trunk types yes music on hold yes operator yes pbx compatibility yes pc programming yes ip stations can be programmed from pcpro for ip duplication. Prime line selection yes private line yes ring groups yes selectable ring tones yes ri...
Page 2007
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1975 analog communications interface (aci) no ancillary device connection no answer hold no answer key no attendant call queuing no automatic call distribution (acd) no background music no barge-in no call appearance (cap) keys no call arrival (car)...
Page 2008
Issue 11.0 univerge sv8100 2 - 1976 wireless dect (sip) drop key no d term cordless ii terminal no d term cordless lite ii terminal no d term handset cordless no d term ip gateway system no electra elite ipk terminals no electra elite terminal migration no facsimile co branch connection no forced tr...
Page 2009
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1977 pulse to tone conversion no redial function no handset has redial list. Repeat redial no reverse voice over no room monitor no save number dialed no handsets have own phone book and redial lists secondary incoming extension no secretary call (b...
Page 2010
Issue 11.0 univerge sv8100 2 - 1978 wireless dect (sip) components of the wireless dect (sip) system include the following: nec c124 sip dect handset the handset has the following features: alphanumeric display with backlight led indication for incoming calls telephone book with 40 entries while idl...
Page 2011
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1979 key lock press ok and to lock the dial pad. Ten different ring tones ring tones can be selected in the tone setup menu and press ok. Microphone mute press while the telephone is off-hook to mute the microphone. Caller id presentation headset co...
Page 2012
Issue 11.0 univerge sv8100 2 - 1980 wireless dect (sip) 2. Name only. 3. Number only. 4. None. If calling from voice mail 1. Program 45-01-02 voice mail master name. 2. Program 45-01-09 centralized voice mail master name. 3. Program 15-01-01 calling station information (voicemail extension). Conditi...
Page 2013
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1981 conditions 12 simultaneous calls can be made per dect access point. When the wireless dect (sip) telephone does not respond to an incoming call within 12 seconds because it is out of area, the originator hears a busy tone. The out of area timer...
Page 2014
Issue 11.0 univerge sv8100 2 - 1982 wireless dect (sip) off-hook signaling description this feature enables the display of off-hook signaling on an ip dect terminal while talking with the 1st call. Conditions multiple call appearance and call waiting indication must be turned on for the sip dect sys...
Page 2015
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1983 with sv8100 version 5000 (5.00 or higher) software and pz-iplb daughter board installed, half duplex connections are not supported. For troubleshooting purposes, a managed switch capable of port mirroring is required to capture packet data from...
Page 2016
Issue 11.0 univerge sv8100 2 - 1984 wireless dect (sip) with sv8100 version 5000 (5.00 or higher) software and pz-iplb daughter board installed, half duplex connections are not supported. For troubleshooting purposes, a managed switch capable of port mirroring is required to capture packet data from...
Page 2017
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1985 in case of internal call from other standard sip terminal, lock-out tone is not applied. Caller hears a busy tone. Default setting enabled system availability terminals nec c124 sip dect handset nec g955 sip dect handset ip dect standard sip te...
Page 2018
Issue 11.0 univerge sv8100 2 - 1986 wireless dect (sip) guide to feature programming the level 1, level 2 and level 3 columns indicate the programs that are assigned when programming this feature in the order they are most commonly used. These levels are used with pcpro and webpro wizards for featur...
Page 2019
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1987 10-12-10 cd-cp00-us network setup – subnet mask define the media gateway subnet mask address. 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0....
Page 2020
Issue 11.0 univerge sv8100 2 - 1988 wireless dect (sip) voip tos setup: the univerge sv8100 supports quality of service (qos) marking for the session initiation protocol (sip). 10-26-03 ip system operation setup – sip peer to peer mode enable/disable the peer to peer feature for sip ip stations. 0 =...
Page 2021
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1989 ip extension numbering: sip extension codec information: program number program name description/comments assigned data level 1 2 3 11-02-01 extension numbering define the ip phone extension number. This designated extension is used to register...
Page 2022
Issue 11.0 univerge sv8100 2 - 1990 wireless dect (sip) 84-19-07 sip extension codec information basic setup – number of g.729 audio frames define the g.729 audio frame size. 1~6 1 = 10ms 2 = 20ms 3 = 30ms 4 = 40ms 5 = 50ms 6 = 60ms (default = 2) 84-19-08 sip extension codec information basic setup ...
Page 2023
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1991 84-19-27 sip extension codec information basic setup – rx gain define rx gain values – adjusting this value increases or decreases volume levels for the sending party. Consult the univerge sv8100 programming manual for transmit gain scale to se...
Page 2024
Issue 11.0 univerge sv8100 2 - 1992 wireless dect (sip) sip extension basic information setup: 84-19-38 sip extension ip codec information basic setup – number of g.726 audio frames define the number of g.726 audio frames. 1~4 1 = 10ms 2 = 20ms 3 = 30ms 4 = 40ms (default = 3) 84-19-39 sip extension ...
Page 2025
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1993 ip phone configuration: 84-26-01 ipl basic setup – ip address assign the ip address for each dsp on the ipla. Xxx.Xxx.Xxx.Xxx defaults: slot 1 = 172.16.0.20 : slot 4 = 172.16.0.44 voip gw number 1~8 172.16.0.20 ~ 172.16.16.0.27 84-26-02 ipl bas...
Page 2026
Issue 11.0 univerge sv8100 2 - 1994 wireless dect (sip) 15-05-07 ip telephone terminal basic data setup – using ip address review the registered ip phones ip address [informational only]. 0.0.0.0~ 255.255.255.255 (default = 0.0.0.0) 15-05-15 ip telephone terminal basic data setup – codec type assign...
Page 2027
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1995 off-hook signalling: program number program name description/comments assigned data level 1 2 3 11-12-03 service code setup (for service access) – override (off-hook signaling) customize the override (off-hook signaling) used for service access...
Page 2028
Issue 11.0 univerge sv8100 2 - 1996 wireless dect (sip) caller id display after a call transfer: program number program name description/comments assigned data level 1 2 3 20-06-01 class of service for extensions assign a class of service (1~15) to an extension. Day night/mode: 1~8 class of service ...
Page 2029
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1997 out of range call warning notification: 24-09-04 call forward split settings – co call forwarding busy destination assign co call forwarding for busy destinations. 0~9, # , , p, r, @ (up to 24 digits) p = pause r = hookflash @ = wildcard (defa...
Page 2030
Issue 11.0 univerge sv8100 2 - 1998 wireless dect (sip) operation placing an outside call with pre-dial: 1. Dial 9. 2. Press and hold the # key to insert a pause (–), if necessary. 3. Dial the outside number. 4. Press the key (on-hook/off-hook). For more information on the wireless dect (sip) featur...
Page 2031
Univerge sv8100 issue 11.0 wireless dect (sip) 2 - 1999 2. Answer on ip dect 200 and talk with ext 100. 3. From ext 101 call ip dect (2nd call). 4. Ip dect receives off-hook signal. 5. Press the button on the ip dect. Hold the 1st call and answer the 2nd call. 6. Talk with ext 101. 7. Use on-hook on...
Page 2032
Issue 11.0 univerge sv8100 2 - 2000 wireless dect (sip) 6. Talk with ext 101. 7. Use on-hook on ext 101. A busy tone is heard on the ip dect. 8. Press the button on the ip dect and retrieve the 1st call (on hold). 9. Talk with ext 100. Caller id display after a call transfer: to make screened transf...
Page 2033: Codes T
Features and specifications manual 3 - 1 codes t a b les 3 codes tables s ection 1 a bout t his c hapter the charts in this chapter provide a list of the service codes, function key codes, and system number plan/capacities. The service codes and function codes are listed by number and by feature in ...
Page 2034
Issue 11.0 univerge sv8100 3 - 2 codes tables s ection 3 u sing h andsfree the manual assumes each extension has automatic handsfree. This lets a user just press a line key or speaker key to answer or place a call. For extensions without automatic handsfree, the user must: lift the handset or press ...
Page 2035
Univerge sv8100 issue 11.0 features and specifications manual 3 - 3 table 3-2 service codes by number dial this service code. . . 1 when you . . . For this feature. . . Also see function key. . . 1 except where indicated, dial service code from intercom dial tone (e.G., press idle speaker first). + ...
Page 2036
Issue 11.0 univerge sv8100 3 - 4 codes tables 3 (after + 001~200 + busy) disconnect a call in progress on a trunk. Forced trunk disconnect - 4 + 3 + message (01~20), or + 3 + hang up to cancel activate or cancel selectable display messaging. Selectable display messaging 17 4 + 6 + trunk access code ...
Page 2037
Univerge sv8100 issue 11.0 features and specifications manual 3 - 5 #5 use last number redial. Last number redial - #6 + orbit (01~64) park a call in a system park orbit (1~8, 01~32 or 01~64). Park 04 + orbit (1~64) #7 use personal speed dialing. Speed dialing - #8 set up an unsupervised conference....
Page 2038
Issue 11.0 univerge sv8100 3 - 6 codes tables 604 + group number (1~8 or 01~64) + mode + extension set the destination for automatic transfer setup for each extension group. Transfer - 605 + group number (1~8 or 01~64) set delayed transfer for each extension group. Transfer - 606 + group number (1~8...
Page 2039
Univerge sv8100 issue 11.0 features and specifications manual 3 - 7 627 enable dnd at a room telephone. Hotel/motel (do not disturb) - 628 cancel dnd at a room telephone. Hotel/motel (do not disturb) - 629 enable dnd for another room telephone. Hotel/motel (do not disturb) - 630 cancel dnd at anothe...
Page 2040
Issue 11.0 univerge sv8100 3 - 8 codes tables 645 + trunk # + 1 (block) 645 + trunk # + 0 (enable) block/busy out outbound usage on a trunk with trunk port disable. Central office calls, placing - 650 + 0 (install) or 1 (remove) log in (0) or log out (1) for your department calling group. Department...
Page 2041
Univerge sv8100 issue 11.0 features and specifications manual 3 - 9 675 monitor a room telephone. Hotel/motel (room monitor) - 677 change the cos of another extension. Must be allowed in program 20-13-28. Class of service - 678 + 0~9 change the language of a display telephone. Alphanumeric display /...
Page 2042
Issue 11.0 univerge sv8100 3 - 10 codes tables 715 save a number (from slt) or dial a saved number save number dialed 30 718 + 1 718 + 2 718 + 3 718 + 4 718 + 5 718 + 6 718 + 7 718 + 8 activate day 1 mode. Activate night 1 mode. Activate midnight 1 mode. Activate rest 1 mode. Activate day 2 mode. Ac...
Page 2043
Univerge sv8100 issue 11.0 features and specifications manual 3 - 11 747 + 0 (cancel) 1 (trk calls) 2 (paging, icm, call forward and transfers) 3 (all calls) 4 (call forwards) activate do not disturb. Do not disturb - 749 place a call on exclusive hold at an slt. Hold - 750 camp on to an extension w...
Page 2044
Issue 11.0 univerge sv8100 3 - 12 codes tables 763 join a meet me conference or meet me page on an internal paging zone (if your extension is in the group called). Meet me conference meet me paging 23 or 32 764 + zone paged (0~9 or 00~64) join a meet me conference or meet me page if your extension i...
Page 2045
Univerge sv8100 issue 11.0 features and specifications manual 3 - 13 782 route ani/dnis to the vrs. It can also be used to transfer to vrs. Transfer voice response service (vrs) - 783 enable the data communication auto-answer mode. Data communications - 784 access the vrs. Voice response service (vr...
Page 2046
Issue 11.0 univerge sv8100 3 - 14 codes tables table 3-3 service codes by feature for this feature... Dial this service code... 1 when you ... Also see function key... 1 except where indicated, dial service code from intercom dial tone (e.G., press idle speaker first). Speed dialing 753 + bin + numb...
Page 2047
Univerge sv8100 issue 11.0 features and specifications manual 3 - 15 automatic call distribution (acd) 5 log out of or in to an acd group. 10 655 log out of or in to an acd group from an slt. 656 activate work time from an slt. 17 657 cancel work time from an slt. 17 658 activate rest mode from an s...
Page 2048
Issue 11.0 univerge sv8100 3 - 16 codes tables call forwarding 745 set/cancel call forwarding (both ringing). - 742 set/cancel call forwarding when busy. - 744 set/cancel call forwarding when busy/no answer. - 743 set/cancel call forwarding no answer. - 746 set/cancel call forwarding follow me. - 74...
Page 2049
Univerge sv8100 issue 11.0 features and specifications manual 3 - 17 central office calls, answering / hold #0 use universal answer to pick up a call ringing over the paging system. - 672 + line number (001~200) answer a call on a specific trunk. - 679 + 1 (set) or 0 (cancel) change the ability for ...
Page 2050
Issue 11.0 univerge sv8100 3 - 18 codes tables do not disturb 747 + 0 (cancel) 1 (trk calls) 2 (paging, icm, call forwards, and transfers) 3 (all calls) 4 (call forwards) activate do not disturb. - door box 702 + door box (1~4 or 1~8) place a call to a door box. - 722 forward a door box off-premise....
Page 2051
Univerge sv8100 issue 11.0 features and specifications manual 3 - 19 hold 732 placing a call on group hold. - 749 place a call on exclusive hold at an slt. - 759 retrieve a call from exclusive hold at a 2-button telephone. - 762 pick up a call from group hold. - hotel/motel (do not disturb) 627 enab...
Page 2052
Issue 11.0 univerge sv8100 3 - 20 codes tables hotel/motel (room status) 638 set a room as checked in. - hotel/motel (room status) 639 set room as checked out. - hotel/motel (room status) 641 set a room as available (clean) from another telephone. - hotel/motel (room status printouts) 642 request a ...
Page 2053
Univerge sv8100 issue 11.0 features and specifications manual 3 - 21 music on hold 781 + 00 (no tone), 01 (general) or 02 (holiday) change the music on hold tone. - name storing 700 + enter name + hold program extension names. 55 night service 618 use night mode switching for other group. - 718 + 1 ...
Page 2054
Issue 11.0 univerge sv8100 3 - 22 codes tables programmable function keys 751 + key + code change the function of a programmable key using 751 service code. - 752 + key + code change the function of a programmable key using 752 service codes. - save number dialed 715 save a number (from slt) or dial...
Page 2055
Univerge sv8100 issue 11.0 features and specifications manual 3 - 23 toll restriction, dial block 600 + code + 0 use dial block. - 601 + code + 0 as a supervisor use dial block. - toll restriction override 775 + pswd (0000) + place outside call temporarily override an extension toll restriction. - 6...
Page 2056
Issue 11.0 univerge sv8100 3 - 24 codes tables trunk group routing or automatic route selection 9 place a call using trunk group routing or automatic route selection. 02 trunk queuing 8 call your mailbox. 67 654 enable conversation record at an slt. - # (off-hook) camp on to or leave a callback at a...
Page 2057
Univerge sv8100 issue 11.0 features and specifications manual 3 - 25 voice response system (vrs) + ringing ext. Pick up a call ringing another extension for directed call pickup or vrs park and page. - 616 + 7 + record message + # + condition (2, 4,6 or 7) + destination + type (2 or 3) or 616 + 7 + ...
Page 2058
Issue 11.0 univerge sv8100 3 - 26 codes tables table 3-4 function key codes by feature to program a key, press speaker, dial 751 (for 2-digit codes) or 752 (for 3-digit codes), press the key and enter the code (e.G., 48 for voice over). For this feature... Use this key... When you ... Key lamp statu...
Page 2059
Univerge sv8100 issue 11.0 features and specifications manual 3 - 27 automatic call distribution (acd) code: 10 operation: press key to log in press key + 1 to log out or 0 to cancel basic operation log in or out of an acd group. On red when logged in off when logged out - code: 12 operation: press ...
Page 2060
Issue 11.0 univerge sv8100 3 - 28 codes tables automatic call distribution (acd) (cont.) code: 16 operation: press key to put agent on hold. Press key again + 1 to hang up agent or 0 to bring agent back into call. Switch (split) between an acd agent and their outside caller after answering an emerge...
Page 2061
Univerge sv8100 issue 11.0 features and specifications manual 3 - 29 call forwarding, external by door box code: 54 operation: press key + dest. Number externally call forward door box calls. Slowly flashes red 722 call forwarding, follow me code: 15 operation: press key + dest. Extension call forwa...
Page 2062
Issue 11.0 univerge sv8100 3 - 30 codes tables department step calling code: 36 operation: dial busy ext + press key step call through a department group for an idle member. None 2 direct station selection / one-touch calling code: 01 operation: press key + dest. Ext. Or outside tel. # + hold call a...
Page 2063
Univerge sv8100 issue 11.0 features and specifications manual 3 - 31 headset operation code: 05 operation: press key enable or disable headset operation. On red when activated 688 hold code: 44 operation: place or answer call + press key put a call on system hold (if your telephone hold key is reass...
Page 2064
Issue 11.0 univerge sv8100 3 - 32 codes tables networking code: 06 + network (01~50) operation: press key access a networked trunk. None - night service code: 09 + mode (1~4 or 1~8) operation: press key activate the day/night mode. On red when activated 718 + + 0 off-hook signaling code: 33 operatio...
Page 2065
Univerge sv8100 issue 11.0 features and specifications manual 3 - 33 save number dialed code: 30 operation: save: place call + press key redial: line or speaker key + press key save, redial or check saved number. None - secretary call (buzzer) code: 41 + sec. Ext operation: press key call your secre...
Page 2066
Issue 11.0 univerge sv8100 3 - 34 codes tables voice response system (vrs) (park and page) (personal greeting) code: 17 operation: press key + device type code + requested data (depends on device selected). Set up call forwarding off-premise, selectable display messaging, vrs park and page or vrs pe...
Page 2067
Univerge sv8100 issue 11.0 features and specifications manual 3 - 35 table 3-5 function key codes by number to program a key, press speaker, dial 751 (for 2-digit codes) or 752 (for 3-digit codes), press the key and enter the code (e.G., 48 for voice over). Use this key... For this feature... When y...
Page 2068
Issue 11.0 univerge sv8100 3 - 36 codes tables code: 11 operation: press key + dest. Ext. Call forwarding, busy call forward to extension or voice mail. Slowly flashes red 742 code: 12 operation: press key + dest. Ext. Call forwarding, no answer call forward to extension or voice mail. Slowly flashe...
Page 2069
Univerge sv8100 issue 11.0 features and specifications manual 3 - 37 code: 25 operation: speaker key + press key group call pickup answer a call ringing a telephone in another pickup group – if you do not know the group number. None 769 code: 26 + pickup group (1~8 or 1~9 or 01~64) operation: speake...
Page 2070
Issue 11.0 univerge sv8100 3 - 38 codes tables code: 33 operation: call ext. And receive busy + press key off-hook signaling signal a busy extension. None 709 code: 34 operation: call ext + press key barge-in barge-in on a co-worker’s conversation. None 710 code: 35 operation: call busy extension or...
Page 2071
Univerge sv8100 issue 11.0 features and specifications manual 3 - 39 code: 41 + sec. Ext. Operation: press key secretary call call your secretary (using the buzzer). On red at source fast flash red at destination - code: 42 + boss ext. Operation: press key as a secretary pick up a call ringing your ...
Page 2072
Issue 11.0 univerge sv8100 3 - 40 codes tables code: 51 + relay number operation: press key general purpose relay activate the general purpose relay. On when active 780 code: 55 operation: do not lift the handset + press key + enter extension number + enter name + press hold name storing change the ...
Page 2073
Univerge sv8100 issue 11.0 features and specifications manual 3 - 41 code: 03 + ext. Or department group operation: press key call arrival (car) keys call arrival (car) key : place or answer a call from your virtual (phantom) extension or call arrival (car) key : place or answer a call to your co-wo...
Page 2074
Issue 11.0 univerge sv8100 3 - 42 codes tables code: 10 operation: press key to log in press key + 1 to log out or 0 to cancel automatic call distribution (acd) basic operation log in or out of an acd group. On red when logged in off when logged out 5 code: 12 operation: press key emergency call pla...
Page 2075
Univerge sv8100 issue 11.0 features and specifications manual 3 - 43 code: 17 operation: press key automatic call distribution (acd) (continued) work time enable/disable work time. On when work time enabled, flashing (while on a call) if auto work time enabled off when work time disabled - code: 18 ...
Page 2076
Issue 11.0 univerge sv8100 3 - 44 codes tables this page intentionally left blank.
Page 2077: E A
Features and specifications manual 4 - 1 fe at ur e a vaila bility b y softw a re r evision 4 feature availability by software revision s ection 1 f eature a vailability c hart this chapter provides an alphabetical listing of the features that are available with each software revision. Note: the fol...
Page 2078
Issue 11.0 univerge sv8100 4 - 2 feature availability by software revision table 4-1 feature availability by software revision univerge sv8100 feature name ver. 1000 ver. 1100 ver. 2000 ver. 2500 ver. 3000 ver. 4000 ver. 5000 ver. 6000 ver. 7000 ver. 8000 account code – forced/verified/unverified s ...
Page 2079
Univerge sv8100 issue 11.0 features and specifications manual 4 - 3 call waiting/camp-on s s s s s s s s s s callback s s s s s s s s s s caller id call return s s s s s s s s s s caller id s s s s e e e s s s caller id – flexible ringing n/a n/a n/a n/a s s s s s s central office calls, answering s...
Page 2080
Issue 11.0 univerge sv8100 4 - 4 feature availability by software revision direct station selection (dss) console s s s s s s s s s s directed call pickup s s s s s s s s s s directory dialing s s s s e s s s s s distinctive ringing, tones and flash patterns s s s s e s s s s s do not disturb s s s ...
Page 2081
Univerge sv8100 issue 11.0 features and specifications manual 4 - 5 hotel/motel s s s s s s s s e s hotline s s s s s s s s s s howler tone service s s s s s s s s s s intercom s s s s s s s s e s ip multiline station (sip) s s s s e s e e s s ip multiline station (sip) – ml440 cordless n/a n/a n/a ...
Page 2082
Issue 11.0 univerge sv8100 4 - 6 feature availability by software revision mh240 wireless ip telephone n/a n/a n/a s e s e s s s microphone cutoff s s s s s s s s s s mobile extension s s s s e s e s s s multiple trunk types s s s s s s s s s s music on hold s s s s s s s s s s name storing s s s s ...
Page 2083
Univerge sv8100 issue 11.0 features and specifications manual 4 - 7 ringdown extension, internal/external s s s s s s s s s s room monitor s s s s s s s s s s save number dialed s s s s s s s s s s secondary incoming extension s s s s e s s s s s secretary call (buzzer) s s s s s s s s s s secretary...
Page 2084
Issue 11.0 univerge sv8100 4 - 8 feature availability by software revision t1 trunking (with ani/dnis compatibility) s s s s s s s s s s tandem ringing s s s s s s s s s s tandem trunking (unsupervised conference) s s s s s s s s s s tapi compatibility s s s s s e s s s s tone override s s s s s s s...
Page 2085
Univerge sv8100 issue 11.0 features and specifications manual 4 - 9 vm8000 inmail – language setting n/a n/a n/a n/a n/a s s s s s voice call recording n/a n/a n/a n/a s s s e s s voice mail integration (analog) s s s s s s s s s s voice mail message indication on line keys s s s s s s s s s s voice...
Page 2086
Issue 11.0 univerge sv8100 4 - 10 feature availability by software revision this page intentionally left blank.
Page 2088: Eatures
F eatures and s pecifications m anual nec corporation of america issue 11.0 (version 8000) ®.