SAGEMCOM MF 4591 User Manual - page 68
68
Sagemcom · MF 4591
EN
Enter the outside line access
code
1. Press
OK, 0522 and OK.
2. Enter the outside line access code with which you
reach the public telephone network. This is usu-
ally
0.
3. Confirm with
OK.
Spaltenumbruch
%%%Spaltenumbruch$$$
DSL Connection
· DSL Connection
DSL Connection
In the event that you use a DSL modem: Connect the
device to the slot intended for analogue telephones/
fax machines! For additional information, please
consult the operating manual of your DSL system.
Ask your telephone or internet service provider if
necessary.
ISDN Connection
· ISDN Connection
ISDN Connection
Your device is an analogue fax device (Group 3). It is
not an ISDN device (Group 4), and therefore it cannot
be operated directly on an ISDN connection. In order
to do this, you need either an analogue adapter or a
connection for analogue terminals. Details for ISDN
connections can be found in the instructions provid-
ed with the terminal adapter or the dial-up router.
Connecting
Additional Devices
· Connecting Additional Devices
Additional Devices
You can operate additional devices on a telephone
line, such as cordless telephones, answering ma-
chines, modems or charge counters.
Connection to the
Device
Connection to the Device
You can connect additional devices directly to your
device. Insert the telephone cable of the additional
device into the
Ï/EXT. socket (RJ-11-connection)
on the device.
Externe Geräte anschließen
Connection to the
Telephone Line
Order of Connections
In order for the fax switch to function, the device
must be first in the series if multiple devices are con-
nected to the same telephone socket. Follow the cor-
rect order.
Connection to the First Telephone Socket
Using Additional
Telephones
(Easylink)
· Using Additional Telephones (Easylink)
Easylink
With the Easylink function you can control your de-
vice with additional telephones. To use this function,
additional telephones must be set to the tone dial-
ling mode (DTMF/MFV tones) (for this purpose see
the operating manual of your additional telephone).
Starting Fax Reception
If you pick up at an additional device and hear that you
are receiving a fax (whistling tone or silence), you can
start the fax reception by pressing
*5 on the ad-
ditional telephone or pressing
o on the device.
Hang up Additional Telephone
Hang up the additional telephone when the ring tone
changes. The device has accepted the reception of
the fax message.
Taking Over the Line
If you pick up on an additional telephone and the de-
vice continues to ring or attempts to receive a fax,
you can disconnect the device from the line. Press
** on the additional telephone.
Using an External
Answering Machine
· Using an External Answering Machine
Your external answering machine must have parallel
recognition for accepting incoming calls. Consult
your retailer.
For the best operation, the answering machine must
be connected to the
Ï/EXT. socket of the device.
Select EXT/ answering machine mode as the fax re-
ception mode (see also chapter
Setting the Fax Re-
ception Mode
, page 62).
Length of Outgoing Message
Incorrect Outside Line Access Code
In rare cases, the outside line access code
may be a different number or a two-digit
number. For older telephone systems, the
outside line access code can be R (=
Flash). Press
Rø to enter this outside
line access code. If the connection to the
public telephone network is not possible,
contact your telephone system supplier.
Connection to the First Telephone Socket
If you have multiple telephone sockets for
the same telephone line, the device must be
connected to the first telephone socket.
Length of Outgoing Message
The outgoing message must be shorter than
ten seconds. Avoid music in your announce-
ment. If the external answering machine has
a “conserving function” (i.e. a function that
changes the number of rings as soon as new
messages have been recorded), switch it off.