D-Link xStack DGS-3600 Series User Manual - Ports
xStack DGS-3600 Series Layer 3 Stackable Fast Ethernet Managed Switch
•
RS-232 DCE console port for Switch management
Provides parallel LED display for port status such as link/act, speed, etc.
•
•
•
•
•
•
•
•
IEEE 802.3 10BASE-T compliant
High performance switching engine performs forwarding and filtering at wire speed, maximum 14, 881 packets/sec
on each 10Mbps Ethernet port, maximum 148,810 packet/sec on 100Mbps Fast Ethernet port and 1,488,100 for each
Gigabit port.
Full and half-duplex for both 10Mbps and 100Mbps connections. Full duplex allows the switch port to
simultaneously transmit and receive data. It only works with connections to full-duplex-capable end stations and
switches. Connections to a hub must take place at half-duplex
Support broadcast storm filtering
Non-blocking store and forward switching scheme capability to support rate adaptation and protocol conversion
Supports by-port Egress/Ingress rate control.
Efficient self-learning and address recognition mechanism enables forwarding rate at wire speed
Ports
The following table lists the relative ports that are present within each switch:
DGS-3627
DGS-3627G
DGS-3650
Twenty-four 10/100/100BASE-T
Four SFP Combo Ports
Three open slots used to add
single-port 10GE modules
One female DCE RS-232 DB-9
console port
Twenty-four 1000Mbps SFP Ports
Four 1000BASE-T Combo Ports
Three open slots used to add single-
port 10GE modules
One female DCE RS-232 DB-9
console port
Forty-eight 10/100/100BASE-T
Four SFP Combo Ports
Two open slots used to add
single-port 10GE modules
One female DCE RS-232 DB-9
console port
The following table lists the features and compatibility for each type of port present in the xStack DGS-3600 series.
10/100/1000BASE-T
SFP Combo
1000BASE-T Combo
10GE Module
IEEE 802.3 compliant
IEEE 802.3u compliant
IEEE 802.3x flow control
support in full-duplex
One connector in the
rear to add an external
Redundant Power
Supply (DPS-500)
Auto MDI-X/MDI-II cross
over support
Supports the following SFP
transceivers:
DEM-310GT (1000BASE-LX)
DEM-311GT (1000BASE-SX)
DEM-312GT2 (1000BASE-LX)
DEM-314GT (1000BASE-LH)
DEM-315GT (1000BASE-ZX)
DEM-330T/R (WDM)
DEM-331T/R (WDM)
Will take priority over its
10/100/1000BASE-T combo
ports
IEEE 802.3z compliant
One connector in the rear to
add an external Redundant
Power Supply (DPS-500)
IEEE 802.3 compliant
IEEE 802.3u compliant
IEEE 802.3ab compliant
IEEE 802.3z compliant
IEEE 802.3x flow control
support in full-duplex
One connector in the
rear to add an external
Redundant Power
Supply (DPS-500)
IEEE 802.3ae compliant
IEEE 802.3ak compliant
Full-duplex only
Supports the following
modules:
DEM-410CX Single-Port CX4
DEM-410X Single-Port XFP
One connector in the rear to
add an external Redundant
Power Supply (DPS-500)
NOTE:
The SFP combo ports on the Switch cannot be used simultaneously with the
corresponding 1000BASE-T ports. If both ports are in use at the same time (ex. port 25
of the SFP and port 25 of the 1000BASE-T), the SFP ports will take priority over the
combo ports and render the 1000BASE-T ports inoperable.
3