Samlexpower EVO-2212E Owner's Manual - Section 4 |
16 | SAMLEX AMERICA INC.
APPENDIX A
SECtION 4 |
Parameter Setup
4.3 PASSWoRD PRotection FoR PARAMeteR cHAnGe
All parameters except Time and Date are protected with a Password. When the required
parameter screen is reached and is displayed and enter Key is pressed to modify the parameter
value, the system will request a 4-digit Password. the Password is 8052. Once you enter the
Password correctly, you don’t need to enter the Password again until until any key is not pressed
for over 60 seconds. An example of Parameter setting is shown at Section 4.3.1 below:
4.3.1 example of Password Activation and changing Bulk current Setting –
From Default 40A to 50A
KEY IN PASSWORD
0000
SELECT GROUP
CHARGE CURVE
BULK CURRENT
40 A
PASSWORD CORRECT
PASSWORD ERROR!!
BULK CURRENT
40 A
BULK CURRENT
90 A
!
WRITING...
50 A
WRITE SUCCESS!
50 A
WRITE FAILURE!
50 A
OUT OF RANGE!
90 A
BULK CURRENT
50 A
Starting from any of the 4 Operating Mode Screens (shown at Fig 3.1),
press enterkey.Screen"SELECTGROUP,CHARGECURVE"asshown
on the left will be displayed (Group 1 of "Select Group" Menu Map,
Fig 4.3)
Press enter key to access up to 18 Parameter Screens under Group 1
"Charge Curve", (Parameters are detailed at Table 4.4 and Fig 4.1)
KEY IN PASSWORD
0000
SELECT GROUP
CHARGE CURVE
BULK CURRENT
40 A
PASSWORD CORRECT
PASSWORD ERROR!!
BULK CURRENT
40 A
BULK CURRENT
90 A
!
WRITING...
50 A
WRITE SUCCESS!
50 A
WRITE FAILURE!
50 A
OUT OF RANGE!
90 A
BULK CURRENT
50 A
Screen "BULK CURRENT, 40A" as shown on the left will be displayed
(Page1ofGroup1SELECTGROUP"CHARGECURVE",Fig4.1).
Default current setting of 40A or previously set value will be displayed.
Press enter Key to change Bulk Current parameter setting. A
Password will be requested.
KEY IN PASSWORD
0000
SELECT GROUP
CHARGE CURVE
BULK CURRENT
40 A
PASSWORD CORRECT
PASSWORD ERROR!!
BULK CURRENT
40 A
BULK CURRENT
90 A
!
WRITING...
50 A
WRITE SUCCESS!
50 A
WRITE FAILURE!
50 A
OUT OF RANGE!
90 A
BULK CURRENT
50 A
Password consisting of 4 digits will be requested. 4 digits will be
displayed (with initial value 0000) with the cursor blinking on the first
digit (0) on the left. Use Up /Down Keys to scroll to number 8 for the
first digit “8” of the password. Momentarily press enter Key (Short
press). Digit 8 will be entered as the first digit of the Password and
the blinking curser will automatically move to the 2nd digit (0) to the
right. As the next digit in the Password “8052” is “0”, momentarily
press enter Key (Short press) to enter “0” in the second digit.
The blinking cursor will automatically move to the 3rd digit (0). Use
Up /Down Keys to scroll to number 5 for the 3rd digit “5” of the
password “8052” and momentarily press enter Key (Short press).
The blinking cursor will automatically move to the 4th digit (0). Use
Up /Down Keys to scroll to number 2 for the 4th digit “2” of the
password “8052”. Now keep the
enter Key pressed continuously
for longer time (3 to 4 sec) to write the full password of 4 digits
i.e. “8052”.
KEY IN PASSWORD
0000
SELECT GROUP
CHARGE CURVE
BULK CURRENT
40 A
PASSWORD CORRECT
PASSWORD ERROR!!
BULK CURRENT
40 A
BULK CURRENT
90 A
!
WRITING...
50 A
WRITE SUCCESS!
50 A
WRITE FAILURE!
50 A
OUT OF RANGE!
90 A
BULK CURRENT
50 A
Flashes twice when Password is correct. (8052)