Jeep 1996 Grand Cherokee Service Manual - page 997
(3) Lower engine with lifting fixture while aligning
engine support insulator assembly into sill bracket
assembly.
(4) Install the thru-bolt and nut. Tighten the
RIGHT SIDE nut to 81 N·m (60 ft. lbs.) torque.
Tighten the LEFT SIDE nut to 81 N·m (60 ft. lbs.)
torque.
(5) Lower the vehicle.
(6) Remove lifting fixture.
(7) Connect the negative cable to the battery.
ENGINE MOUNTS—REAR
REMOVAL
(1) Disconnect the negative cable from the battery.
(2) Raise the vehicle on a hoist.
(3) Support the transmission with a jack.
(4) Remove engine mount bracket thru-bolt (Fig.
17).
(5) Raise the transmission and engine SLIGHTLY.
(6) Remove stud nuts attaching engine mount cle-
vis
bracket
to
crossmember
(Fig.
17).
Remove
bracket.
(7) Remove the engine mount bracket assembly
from the adaptor (Fig. 17).
(8) If required, remove the transmission support
bracket adaptor.
INSTALLATION
(1) If the transmission support bracket adaptor
was removed, position the adaptor to the transmis-
sion (Fig. 17). Tighten the bolts to 60 N·m (44 ft. lbs.)
torque.
(2) Install the engine mount clevis bracket onto
crossmember. Tighten the stud nuts to 41 N·m (30 ft.
lbs) torque.
(3) Install the engine mount bracket assembly to
the adaptor. Install the bolts and tighten to 75 N·m
(55 ft. lbs.) torque.
(4) Lower the transmission and engine while align-
ing the engine mount bracket assembly to the engine
mount clevis bracket.
(5) Install thru-bolt and tighten the nut to 65 N·m
(48 ft. lbs.) torque.
(6) Remove transmission jack.
(7) Lower the vehicle.
(8) Connect the negative cable to the battery.
ENGINE ASSEMBLY
REMOVAL
(1) Scribe hood hinge outlines on hood and remove
the hood.
(2) Remove the battery.
(3) Drain cooling system.
(4) Remove the air cleaner and tube.
(5) Set fan shroud aside.
(6) Remove radiator and heater hoses. Remove the
radiator (refer to Group 7, Cooling System).
(7) Remove the vacuum lines.
(8) Remove the distributor cap and wiring.
(9) Disconnect the accelerator linkage.
(10) Perform the Fuel System Pressure Release
procedure (refer to Group 14, Fuel System).
(11) Remove throttle body.
(12) Remove the starter wires.
(13) Remove the oil pressure wire.
(14) Discharge the air conditioning system, if
equipped (refer to Group 24, Heating and Air Condi-
tioning for service procedures).
(15) Remove air conditioning hoses.
(16) Disconnect
the
power
steering
hoses,
if
equipped.
(17) Remove starter motor (refer to Group 8B, Bat-
tery/Starter Service).
(18) Remove the generator (refer to Group 8C,
Generator Service).
(19) Raise and support the vehicle on a hoist.
(20) Disconnect exhaust pipe at manifold.
(21) Support automatic transmission with a trans-
mission stand. This will assure that the torque con-
verter
will
remain
in
proper
position
in
the
transmission housing.
(22) Remove bell housing bolts and inspection
plate. Attach C-clamp on front bottom of transmis-
sion torque converter housing to prevent torque con-
verter from coming out.
(23) Remove torque converter drive plate bolts
from torque converter drive plate. Mark converter
and drive plate to aid in assembly.
Fig. 17 Engine Rear Support Assembly
9 - 60
5.2L ENGINE
ZJ
REMOVAL AND INSTALLATION (Continued)