Objet Objet30 User Manual - page 3
DOC-24000 Rev. C
Copyright
Copyright © 2011 Objet Geometries Ltd. All rights reserved.
This documentation contains proprietary information of Objet Geometries Ltd. This information is
supplied solely to assist authorized users of Objet30 3‐D printing systems. No part of this document
may be used for other purposes, and it may not be disclosed to other parties.
The specifications on which this document is based are subject to change without notice.
No part of this book may be reproduced in any form or by any means, nor stored in a database or
retrieval system, without prior permission in writing from Objet Geometries Ltd.
If this document is distributed as a PDF file, you may print it for internal use.
Trademarks
The following are registered trademarks of Objet Geometries Ltd.: Objet
®
, FullCure
®
.
The following are trademarks of Objet Geometries Ltd.: Eden, Eden500V, Eden350V, Eden350,
Eden330, Eden260, Eden260V, Eden250, Connex, Connex500, Connex350, Objet30, Objet30‐Pro,
Objet24, Alaris, Alaris30, PolyJet, PolyJet Matrix, CADMatrix, PolyLog, Objet Studio, Job Manager,
SHR, TangoBlack, TangoBlackPlus, TangoGray, TangoPlus, VeroBlue, VeroGray, VeroWhite,
VeroWhitePlus, VeroBlack, Durus, DurusWhite, RoseClear, Clear, ObjetGreen, Digital Materials.
Microsoft and Microsoft XP are trademarks of Microsoft Corporation.
All names of products and services cited in this book are trademarks or registered trademarks of their
respective companies.
FCC Compliance
The equipment referred to in this guide has been tested and found to comply with the limits for a
Class A device pursuant to part 15 of the FCC rules. These limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. Objet 3‐D
printing systems generate, use and can radiate radio‐frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
The 3‐D printer referred to in this guide contains a transmitter module, FCC ID YH6‐RFID.
NOTE: Objet Geometries is not responsible for radio or TV interference caused by unauthorized
modification to this equipment. Such modification could void the user’s authority to operate the
equipment.
Equipment Recycling
In the European Union, this symbol indicates that when the last user wishes to discard a product, it
must be sent to appropriate facilities for recovery and recycling. For information about proper
disposal, check your purchase contract, or contact the supplier of the equipment.
Limitation of Liability
The product, software or services are being provided on an “as is” and “as available” basis. Except as
may be stated specifically in your contract, Objet Geometries Ltd. expressly disclaims all warranties of
any kind, whether express or implied, including, but not limited to, any implied warranties of
merchantability, fitness for a particular purpose and non‐infringement.
You understand and agree that Objet Geometries Ltd. shall not be liable for any direct, indirect,
incidental, special, consequential or exemplary damages, including but not limited to, damages for
loss of profits, goodwill, use, data or other intangible losses (even if Objet has been advised of the
possibility of such damages), resulting from: (i) the use or the inability to use the product or software;
(ii) the cost of procurement of substitute goods and services resulting from any products, goods, data,
software, information or services purchased; (iii) unauthorized access to or alteration of your
products, software or data; (iv) statements or conduct of any third party; (v) any other matter relating
to the product, software, or services.
The text and drawings herein are for illustration and reference only. The specifications on which they
are based are subject to change. Objet Geometries Ltd. may, at any time and without notice, make
changes to this document. Objet Geometries Ltd., for itself and on behalf of its subsidiaries, assumes
no liability for technical or editorial errors or omissions made herein, and shall not be liable for
incidental, consequential, indirect, or special damages, including, without limitation, loss of use, loss
or alteration of data, delays, or lost profits or savings arising from the use of this document.