Cabletron Systems FRM User Manual - page 390
Idx-2
Frame Relay Module 4. 0 User G uide, Rev 01
Clear Max Stats
2-7
Clear VC on Last Device Down
10-6
Clearing causes
B-1
async
A-5
Collecting Node
4-5
Collecting Node ID
4-4
Collecting Node Pwd (password)
4-4
Com. Port Parity
4-5
Com. Port Stopbit
4-5
Com. Port Thruput
4-5
Command mode (async terminal)
A-1
Committed Burst Size (In/Out)
7-18
Committed Information Rate (In/Out)
7-18
Community Table, configuring
16-3
Configuration database
3-1
Configuration report
3-9
Connection ID
7-19
,
10-7
Connection Priority
7-20
,
8-26
,
8-34
,
9-16
,
10-10
,
11-
9
,
12-16
,
12-18
Connections, displaying
19-3
Controller Type
11-5
Copying a database record
2-7
CSU/DSU Operating Mode
8-10
D
Data Forwarding Char
12-3
Data Forwarding Criteria
12-14
Data transfer mode (async terminal)
A-1
Database
3-1
backing up
18-6
restoring
18-6
setup recommendations
3-1
Database and system memory values
4-3
,
6-3
Date, changing
2-9
DCE Cable Attached
12-11
Default Calling Address
8-12
,
8-19
,
12-11
Default Ethernet Frame Type
15-5
Default Packet Size
8-11
,
8-19
Default Window Size
8-11
,
8-19
Del
13-6
Delay Retry Count
11-6
Delay Timer
11-6
Delete (BSC subscriber)
10-3
,
11-7
Delete CUG
8-21
Delete?
7-22
Deleting a database record
2-7
Destination IP Address
13-11
,
13-12
Destination MAC Address Value
15-9
Destination Mask
13-16
Destination NetBIOS Name
15-10
Destination Network Value
14-7
Destination Node Value
14-7
Destination Socket Value
14-7
Destination Subscriber
13-12
,
14-15
Devices Connected
12-14
Diagnostic codes
B-2
Cabletron-specific
B-4
SNA
B-4
X.25
B-2
Dial port, configuring
8-6
Dial Support
8-13
Disable Request Disconnect
9-9
Disable Status Response
10-13
Disable X.121 User Calls
12-11
Discard Output
12-4
Disconnect Duration
12-13
Disconnect if Clear Recvd
12-13
Disconnect if Clear Sent
12-13
Disconnect Timer
8-13
,
12-12
Display All CUGs
8-21
DLCI configuration, reviewing
7-10
DLCI parameters, configuring
7-12
DLCI sharing
7-1
DLCIs, learned
7-13
Dotted decimal notation
13-1
DSAP Value
15-9
DTE Clear Retry Count
8-12
,
8-20
DTE Reset Retry Count
8-12
,
8-20
DTE Restart Retry Count
8-12
,
8-20
DTR/RTS Active When VC Up
12-12
Dynamic Optimization
7-7
Dynamic Signaling Action
12-14
E
EBCDIC
10-4
,
11-5
Echo
12-3
Echo Mask
12-6
Edit Service Signal
12-5
Editing (in async PAD profile)
12-5
Enable Backup Protocol?
7-19
Enable Bandwidth Allocation
7-17
Enable Inverse ARP
13-11
Enable Outgoing Rate Control
7-17
Enabled (traps)
16-5
Encapsulation Method
8-17
End-to-End Acknowledgement
10-4
Entry
7-22
ERRMSG.TXT
21-1
Errmsg.txt Database Error
4-2
Error codes from async terminal
A-5
Error Retransmit Count
10-7
Escape key
2-8
Event collection, configuring
21-1
Event generation
21-3
Event messages
21-4