Jeep Cherokee 2000 Service Manual - page 338
(12) Remove the starter motor support bracket.
(13) Disconnect the starter motor electrical connec-
tors.
CAUTION: Heatshields are very sharp. Wear gloves
to prevent injury.
(14) Remove the starter heatshield.
(15) Remove the (3) starter motor retaining bolts.
(16) Remove the starter motor from the vehicle.
Installation
(1) Position the starter motor and install retaining
bolts. Torque bolts to 27 N·m (20 ft. lbs.).
(2) Connect the starter motor electrical. Torque
(B+) nut to 27 N·m (20 ft. lbs.).
CAUTION: Heatshields are very sharp. Wear gloves
to prevent injury.
(3) Install the starter heatshield.
(4) Install the starter motor support bracket.
Torque nuts to 10 N·m (90 in. lbs.).
(5) Install the engine mount and engine mount
bracket in the vehicle, making sure sill plate studs
are through engine mount.
(6) Install the engine mount throughbolt and nut
leaving them loose at this time.
(7) Install the (4) engine mount bracket to engine
block bolts. Torque bolts to 61 N·m (45 ft. lbs.).
(8) Tighten, but do not torque (2) right engine
mount lower bolts.
(9) Remove the jack stand.
(10) Torque the (2) lower engine mount bolts to 54
N·m (40 ft. lbs.).
(11) Torque throughbolt nut to 65 N·m (48 ft. lbs.).
(12) Install the oil return line on the engine block
nipple.
(13) Lower the vehicle from the hoist.
(14) Install the (2) engine mount upper sill plate
nuts. Torque nuts to 41 N·m (30 ft. lbs.).
(15) Install the innercooler inlet hose on turbo-
charger.
(16) Connect the negative battery cable.
STARTER — RHD (DIESEL)
REMOVAL
(1) Disconnect the negative battery cable.
(2) Make sure steering wheel is in the unlocked
position.
(3) Raise the vehicle on a hoist.
(4) Rotate the front wheels to access and remove
the steering shaft pinch bolt, slide shaft straight off
gearbox input shaft and position steering shaft aside.
(5) Remove the turbocharger oil return line from
engine block and plug (Fig. 3).
(6) Remove the right engine mount through bolt
nut only (Fig. 3). Do not remove the bolt at this time.
(7) Remove the engine mount upper sill plate nuts.
(8) Position a jack stand and raise weight off right
engine mount.
(9) Remove the track bar support bracket retain-
ing bolts and remove bracket.
(10) Remove the remaining lower engine mount
bolt from the sill plate.
(11) Remove the (4) engine mount bracket bolts.
(12) Remove the engine mount throughbolt.
(13) Remove the engine mount and engine mount
bracket from the vehicle.
(14) Remove the starter motor support bracket.
CAUTION: Heatshield is very sharp. Wear gloves to
prevent injury.
(15) Remove the starter heat shield.
(16) Disconnect the starter motor electrical connec-
tors.
(17) Remove the (3) stater motor retaining bolts.
(18) Remove the starter motor from the vehicle.
Installation
(1) Position the starter motor. Torque retaining
bolts to 27 N·m (20 ft. lbs.).
Fig. 3 Turbocharger Oil Return Line
1 – VEHICLE UNDERBODY
2 – RIGHT ENGINE MOUNT THROUGHBOLT NUT
3 – TURBOCHARGER OIL RETURN HOSE
4 – EXHAUST MANIFOLD DOWNPIPE
5 – TURBOCHARGER
8B - 2
STARTING SYSTEMS
XJ
REMOVAL AND INSTALLATION (Continued)