Jeep Cherokee 2000 Service Manual - page 552
Check for continuity between the ground circuit cav-
ity of the stand-alone switch wire harness connector
or the 8-way DDM wire harness connector and a
good ground. There should be continuity. If OK, go to
Step 10. If not OK, repair the circuit to ground as
required.
(10) Check the stand-alone power mirror switch or
DDM-mounted power mirror switch continuity as
shown in (Fig. 1) or (Fig. 2). If OK, go to Step 11. If
not OK, replace the faulty stand-alone power mirror
switch or the faulty DDM.
(11) Connect the battery negative cable. Use two
jumper wires, one connected to a 12-volt battery feed,
and the other connected to a good body ground. See
the Power Mirror Test chart for the correct jumper
wire connections at the mirror half of the power mir-
ror wire harness connector (Fig. 3). If the mirror
reactions are OK, repair the wire harness between
the mirror and the stand-alone power mirror switch
or the DDM as required. If the mirror reactions are
not OK, replace the faulty power outside mirror
assembly.
REMOVAL AND INSTALLATION
POWER MIRROR SWITCH
This procedure covers removal of the stand-alone
type power mirror switch. Vehicles with power win-
dows and power locks have a power mirror switch
which is integral to the Driver Door Module (DDM).
See Door Module in this group for the DDM-type
power mirror switch service procedures.
(1) Disconnect and isolate the battery negative
cable.
(2) Using a trim stick or another suitable wide
flat-bladed tool, gently pry around the perimeter
edge of the switch to release the snap clips that
secure the switch to the trim panel (Fig. 4).
(3) Pull the power mirror switch away from the
trim panel far enough to access the wire harness con-
nector.
(4) Unplug the power mirror switch from the wire
harness connector.
(5) Reverse the removal procedures to install.
DOOR MODULE
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the screws that secure the front door
trim panel to the inner door panel (Fig. 5).
(3) Using a trim stick or another suitable wide
flat-bladed tool, gently pry the front door trim panel
away from the door around the perimeter to release
the trim panel retainers.
NOTE: To aid in the removal of the trim panel, start
at the bottom of the panel.
Fig. 1 Stand-Alone Power Mirror Switch Continuity
SELECT RIGHT MIRROR
SWITCH POSITION
CONTINUITY BETWEEN
OFF
1 & 3, 1 & 4, 1 & 5, 1 & 6
UP
2 & 4, 1 & 3, 1 & 5, 1 & 6
DOWN
2 & 5, 1 & 3, 1 & 4, 1 & 6
RIGHT
2 & 6, 1 & 3, 1 & 4, 1 & 5
LEFT
2 & 3, 1 & 4, 1 & 5, 1 & 6
SELECT LEFT MIRROR
SWITCH POSITION
CONTINUITY BETWEEN
OFF
1 & 5, 1 & 6, 1 & 7, 1 & 8
UP
2 & 8, 1 & 5, 1 & 6, 1 & 7
DOWN
2 & 5, 1 & 6, 1 & 7, 1 & 8
RIGHT
2 & 6, 1 & 5, 1 & 7, 1 & 8
LEFT
2 & 7, 1 & 5, 1 & 6, 1 & 8
Fig. 2 Driver Door Module Power Mirror Switch
Continuity
SELECT RIGHT MIRROR
SWITCH POSITION
CONTINUITY BETWEEN
UP
7 & 3, 2 & 5
DOWN
2 & 3, 7 & 5
RIGHT
4 & 3, 2 & 5
LEFT
2 & 3, 6 & 5
SELECT LEFT MIRROR
SWITCH POSITION
CONTINUITY BETWEEN
UP
1 & 3, 2 & 5
DOWN
2 & 3, 1 & 5
RIGHT
6 & 3, 2 & 5
LEFT
2 & 3, 6 & 5
XJ
POWER MIRROR SYSTEMS
8T - 3
DIAGNOSIS AND TESTING (Continued)