NEC SV8500 Operation And Maintenance Manual - page 89
– 42 –
CHAPTER 2
Operations of SV8500 Server
1. HOW TO SET THE CURRENT DATE AND TIME
1.1 General
System clock can be manually or automatically adjusted as shown below. For automatic adjustment, an SNTP
server is required.
Figure 2-1 How to Set the Current Date and Time
1.2 Programming to Specify How to Set Date and Time
(1) When Not Using SNTP Server
STEP 1
ATIM/ATIMN
Date, Time, and Day Light Savings (Start/End) can be specified on this command. By pressing the “Set”
button on the command, the specified Date and Time will be applied to the system that is in operation.
(2) When Using SNTP Server
STEP 1
ATIM
When using Day Light Savings, set the data by using ATIM command.
STEP 2
ANTPL (SNTP Setting)
By this command, set time for time-synchronization (SNTP) service as well as an SNTP server by us-
ing the domain name or IP address. Time adjustment will be automatically performed on a daily basis.
IP Address of the DNS Server must be set using the ADTM command when SNTP server is specified
the domain name.
㪥㪦㪅
㪪㪥㪫㪧㩷㪪㪜㪩㪭㪜㪩
㪚㪦㪤㪤㪘㪥㪛
㪜㪯㪧㪣㪘㪥㪘㪫㪠㪦㪥
㪈
㫅㫆㫋㩷㫌㫊㪼㪻
㪘㪫㪠㪤㪆㪘㪫㪠㪤㪥
㪙㫐㩷㫇㫉㪼㫊㫊㫀㫅㪾㩷㫋㪿㪼㩷 㵰㪪㪼㫋㵱㩷㪹㫌㫋㫋㫆㫅㩷㫆㫅㩷㫋㪿㫀㫊㩷㪺㫆㫄㫄㪸㫅㪻㪃㩷㫋㪿㪼㩷㫊㫇㪼㪺㫀㪽㫀㪼㪻㩷㪻㪸㫋㪼㩷㪸㫅㪻㩷
㫋㫀㫄㪼㩷㪸㫉㪼㩷㪸㫇㫇㫃㫀㪼㪻㩷㫋㫆㩷㫋㪿㪼㩷㫊㫐㫊㫋㪼㫄㪅
㪉
㫌㫊㪼㪻
㪘㪥㪫㪧㪣
㪙㫐㩷㫊㫇㪼㪺㫀㪽㫐㫀㫅㪾㩷㪸㫅㩷㪪㪥㪫㪧㩷㫊㪼㫉㫍㪼㫉㩷㫎㫀㫋㪿㩷㫊㫋㪸㫉㫋㩷㫋㫀㫄㪼㩷㫋㫆㩷㫆㪹㫋㪸㫀㫅㩷㫋㫀㫄㪼㩷㫀㫅㪽㫆㫉㫄㪸㫋㫀㫆㫅㩷
㪽㫉㫆㫄㩷㫋㪿㪼㩷㫊㪼㫉㫍㪼㫉㪃㩷㫋㫀㫄㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫎㫀㫃㫃㩷㪹㪼㩷㪸㫌㫋㫆㫄㪸㫋㫀㪺㪸㫃㫃㫐㩷㫇㪼㫉㪽㫆㫉㫄㪼㪻㩷㫆㫅㩷㪸㩷㪻㪸㫀㫃㫐㩷
㪹㪸㫊㫀㫊㪅
SV8500 server
PCPro
time-synchronization
SNTP server
ATIM/ATIMN
ANTPL
manual adjustment
automatic adjustment