Canon imagePRESS C1 Service Manual - page 1049
Chapter 16
16-152
9. CLEAR
T-16-155
COPIER > FUNCTION > CLEAR
Subheading Contents
Level
ERR
(Target error codes: E000/E001/E002/E003/E005)
Operation method
1) Select this item and press the OK key.
2) Turn OFF/ON the main power.
1
DC-CON
RAM clear for the DC controller PCB
The RAM data is cleared after the main power switch is turned OFF/ON.
Operation method
1) Print out the service mode data by COPIER>FUNCTION>MISC-P>P-PRINT.
2) Select this item and press the OK key.
3) Turn OFF/ON the main power.
4) Enter the data printed by P-PRINT if necessary.
1
R-CON
RAM clear for the reader controller PCB
The setting value is cleared after the main power switch is turned OFF/ON.
Operation method
1) Print out the service mode data by COPIER>FUNCTION>MISC-P>P-PRINT.
2) Select this item and press the OK key.
3) Turn OFF/ON the main power.
4) Enter the data printed by P-PRINT if necessary.
1
JAM-HIST
Clear the jam history.
The jam history is cleared after the OK key is pressed.
Operation method
1) Select this item and press the OK key.
1
ERR-HIST
Clear the error code history.
The error code history is cleared after the OK key is pressed.
Operation method
1) Select this item and press the OK key.
1
PWD-CLR
Clear the password of the "system administrator" specified in the user mode.
The password is cleared after the OK key is pressed.
Operation method
1) Select this item and press the OK key.
1
ADRS-BK
Clear the address book data.
The address book data is cleared after the main power switch is turned OFF/ON.
1) Select this item and press the OK key.
2) Turn OFF/ON the main power.
1
CNT-MCON
Clear the service counter executed for the main controller PCB (main).
(Refer to the section of COUNTER mode for the target counters.)
The counter value is cleared after the OK key is pressed.
1) Select this item and press the OK key.
1
CNT-DCON
Clear the following service counter executed for the DC controller PCB.(Refer to the section of
COUNTER mode for the target counters.)
The counter value is cleared after the OK key is pressed.
1) Select this item and press the OK key.
1
OPTION
Set the setting value of a service mode (OPTION) back to a default value (a value after RAM clear
is executed).
The setting value is cleared after the OK key is pressed.
The data of the main controller, DC controller, and reader controller is cleared.
Operation method
1) Print out the service mode data by COPIER > FUNCTION > MISC-P > P-PRINT.
2) Select this item and press the OK key.
1
MMI
Clear the following user mode setting values.
- Backup data for the copy control panel (user setting value)
- Backup data for common settings (user setting value)
- Various backup data excluding FAX (user setting value)
The setting value is cleared after the main power switch is turned OFF/ON.
Operation method
1) Select this item and press the OK key.
2) Turn OFF/ON the main power.
1
MN-CON
RAM clear for the SRAM board of the main controller PCB
Operation method
1) Select this item and press the OK key.
2) Turn OFF/ON the main power.
- The RAM data is cleared after the main power switch is turned OFF/ON.
- When this mode is executed, all the data in the SRAM board is initialized.
The file control information for a hard disk is also initialized, and image data in the hard disk
cannot be read. Before you execute this mode, be sure to inform a user that all images in the box
are going to be initialized and receive prior approval from him/her.
1) Print out the service mode data by COPIER > FUNCTION > MISC-P > P-PRINT.
2) Select this item and press the OK key. The machine is automatically activated and displays a
message indicating "please turn on the main power again".
3) Turn OFF/ON the main power.
1
CARD
Clear the data related to the card ID (section).
The data related to the card ID is cleared after the main power switch is turned OFF/ON.
Operation method
1) Select this item and press the OK key.
2) Turn OFF/ON the main power.
1
W-TN-CLR
Clear the warning and error indicating waste toner box full.
After replacing the waste toner box, clear the warning/error and the counter detecting waste toner
box full.
Method of Operation
Select the item to highlight, and press the OK key to start operation.
1