Canon imagePRESS C1 Service Manual - page 1162
Chapter 16
16-265
MAG-V-3
Correction of the main scanning magnification for 2nd side printing (151 to 209g)
Enable correction of the main scanning magnification for 2nd side printing of large paper (1-sheet
paper).
2
Setting range: -50 to 50
Factory setting value: 0
The value is incremented by 0.01%.
MAG-H-3
Correction of the sub scanning magnification for 2nd side printing (151 to 209g)
Enable correction of the sub scanning magnification for 2nd side printing of large paper (1-sheet
paper).
2
Setting range: -50 to 50
Factory setting value: 0
The value is incremented by 0.01%.
MAG-M-3
Specifying a material for correction of magnification for 2nd side printing (151 to 209g)
Specify a material for correction of magnification for 2nd side printing of large paper (1-sheet
paper)
0: No setting
1: High quality paper
2: Single-sided coated paper
3: Double-sided coated paper
4: Recycled paper
5: Emboss paper
6: Film
7: Label
8: Postcard
9: Vellum
10: Cotton
2
Setting range: 0 to 10
Factory setting value: 0
MAG-V-4
Correction of the main scanning magnification for 2nd side printing (210 to 256g)
Enable correction of the main scanning magnification for 2nd side printing of large paper (1-sheet
paper).
2
Setting range: -50 to 50
Factory setting value: 0
The value is incremented by 0.01%.
MAG-H-4
Correction of the sub scanning magnification for 2nd side printing (210 to 256g)
Enable correction of the sub scanning magnification for 2nd side printing of large paper (1-sheet
paper).
2
Setting range: -50 to 50
Factory setting value: 0
The value is incremented by 0.01%.
MAG-M-4
Specifying a material for correction of magnification for 2nd side printing (210 to 256g)
Specify a material for correction of magnification for 2nd side printing of large paper (1-sheet
paper)
0: No setting
1: High quality paper
2: Single-sided coated paper
3: Double-sided coated paper
4: Recycled paper
5: Emboss paper
6: Film
7: Label
8: Postcard
9: Vellum
10: Cotton
2
Setting range: 0 to 10
Factory setting value: 0
DEV-VT-L
Set the condition for Clear Toner Consumption Enforcement Sequence movement.
Then set the video count value and threshold value.
As a case example, refer to the 2 following items:
- In the condition of Clear Mono Color Mode, Low Beauty Image, High CV, High Temperature:
if poor Clear Developer Coat, Clear Developer flood appears, set the value higher 3-5.
- If the users indicate the amount of consumable toner, after set the value lower to 1, change the
set value for Related Service Mode, (COPIER > OPTION > BODY > ACR-LV-L) from 0 to 4.
In this case, the productivity will decline.
2
Setting range: 1 to 5
Factory setting value: 2
TOP-H-1
Write start position adjustment on 2nd side in main scanning direction (64 to 105g)
To activate the write start position adjustment on 2nd side of large paper (single sheet image) in
main scanning direction
2
Setting range: -10 to +10
Factory setting value: 0 (0.1mm unit)
TOP-V-1
Write start position adjustment on 2nd side in sub scanning direction (64 to 105g)
To activate the write start position adjustment on 2nd side of large paper (single sheet image) in
sub scanning direction
2
Setting range: -10 to +10
Factory setting value: 0 (0.1mm unit)
TOP-V-2
Write start position adjustment on 2nd side in sub scanning direction (106 to 150g)
To activate the write start position adjustment on 2nd side of large paper (single sheet image) in
sub scanning direction
2
Setting range: -10 to +10
Factory setting value: 0 (0.1mm unit)
COPIER > OPTION > BODY
Subheading Contents
Level