Canon imagePRESS C1 Service Manual - page 440
Chapter 7
7-91
7.14.13 Seal Support Plate (Front)
7.14.13.1 Preparation for Removing the Seal Support
Plate (Front)
0013-9755
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Remove the process unit cover.
3) Hold up the hopper unit.
4) Remove the primary corona assembly. (page 7-86)Reference [Remov-
ing the Primary Corona Assembly]
5) Remove the pre-transfer corona assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Detach the drum unit. (page 7-89)Reference [Removing the Drum Unit]
7) Remove the photosensitive drum. (page 7-90)Reference [Removing the
Photosensitive Drum]
8) Detach the drum cleaning pre-exposure LED unit. (page 7-86)Reference
[Removing the Drum Cleaning Pre-Exposure LED Unit]
9) Detach the scoop-up sheet support plate. (page 7-92)Reference [Remov-
ing the Scoop-Up Sheet Support Plate]
7.14.13.2 Removing the Seal Support Plate (Front)
0013-9756
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the drum cleaner cover [1].
- 1 wire saddle [2] (Remove the harness)
- 1 connector [3]
- 5 screws [4]
F-7-147
2) Detach the seal support plate (front).
- 2 screws [2]
F-7-148
When Mounting the Seal Support Plate (Front/Rear)
- When mounting the seal support plate (front/rear), make the seal support
plate [2] on the scoop-up sheet [1].
F-7-149
- When attaching the seal support plate (front) [1], be sure to support the area
shown in [2] so that the seal support plate (front) is not tilted.
F-7-150
7.14.14 Seal Support Plate (Rear)
7.14.14.1 Preparation for Removing the Seal Support
Plate (Rear)
0013-9753
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Remove the process unit cover.
3) Hold up the hopper unit.
4) Remove the primary corona assembly. (page 7-86)Reference [Remov-
ing the Primary Corona Assembly]
5) Remove the pre-transfer corona assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Detach the drum unit. (page 7-89)Reference [Removing the Drum Unit]
7) Detach the photosensitive drum. (page 7-90)Reference [Removing the
Photosensitive Drum]
8) Detach the drum cleaning pre-exposure LED unit. (page 7-86)Reference
[Removing the Drum Cleaning Pre-Exposure LED Unit]
9) Detach the scoop-up sheet support plate. (page 7-92)Reference [Remov-
ing the Scoop-Up Sheet Support Plate]
7.14.14.2 Removing the Seal Support Plate (Rear)
0013-9754
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the drum cleaner cover [1].
- 1 wire saddle [2] (Remove the harness)
- 1 connector [3]
- 5 screws [4]
[2]
[3]
[4]
[4]
[4]
[1]
[1]
[2]
[2]
[1]
[2]
[1]
[1]
[1]
[2]
[1]
[1]
[2]