Canon imagePRESS C1 Service Manual - page 455
Chapter 7
7-106
- 1 bushing [4]
- 1 gear holder [5]
- 1 gear [6]
F-7-233
7.14.33 ITB Cleaner Brush (Small)
7.14.33.1 Preparation for Removing the ITB Cleaner
Brush (Small)
0013-9723
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Detach the process unit cover.
3) Lift the hopper unit.
4) Remove the primary charging assembly. (page 7-86)Reference [Re-
moving the Primary Corona Assembly]
5) Remove the pre-transfer charging assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Remove the drum unit. (page 7-89)Reference [Removing the Drum
Unit]
7) Pull out the fixing/feeding unit.
8) Remove the intermediate transfer unit. (page 7-100)Reference [Remov-
ing the Intermediate Transfer Unit]
9) Remove the ITB cleaning unit. (page 7-99)Reference [Removing the
ITB Cleaning Unit]
10) Remove the ITB cleaner brush (large). (page 7-105)Reference [Re-
moving the ITB Cleaner Brush (Large)]
7.14.33.2 Removing the ITB Cleaner Brush (Small)
0013-9724
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the ITB cleaner brush unit [1] by shifting it in the direction of ar-
row.
F-7-234
2) Remove 2 E-rings [1], 1 bearing [2], 1 bushing [3], and 1 gear [4].
F-7-235
3) Remove the ITB cleaner brush (small) [1] by shifting it in the direction of
arrow.
- 1 bushing [2]
- 1 bearing [3]
F-7-236
7.14.34 Secondary Transfer Roller Brush (Upper)
7.14.34.1 Preparation for Removing the Secondary
Transfer Roller Brush (Upper)
0013-9773
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Pull out the fixing/feeding unit toward the front.
3) Remove the secondary transfer outside roller unit. (page 7-101)Refer-
ence [Removing the Secondary Transfer Outer Roller Unit]
4) Remove the secondary transfer outside roller sub-unit. (page 7-102)Ref-
erence [Removing the Secondary Transfer Outside Roller Sub-Unit]
5) Remove the secondary transfer outside roller. (page 7-104)Reference
[Removing the Secondary Transfer Outside Roller]
7.14.34.2 Removing the Secondary Transfer Roller Brush
(Upper)
0013-9774
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the washer [1].
- 1 screw [2]
F-7-237
2) Remove the secondary transfer roller brush (upper) [1].
- 3 E-rings [2]
- 1 gear [3]
- 2 bearings [4]
F-7-238
[2]
[2] [3]
[3]
[4]
[5]
[6]
[1]
[2]
[1]
[1]
[1]
[2]
[3]
[4]
[1]
[2]
[3]
[2]
[1]
[1]
[2]
[2]
[2]
[3]
[4]
[4]