Canon imagePRESS C1 Service Manual - page 890
Chapter 15
15-27
0007
Delivery delay
PI13
When the delivery sensor fails to detect a document after it is fed by a specified amount (631mm - length
of document) after the startup of the belt motor during the delivery operation.
0008
Delivery stationary 1
PI13,S9
When the multifeed registration roller sensor detects a document after it is fed by a specified amount
(length of document + 100mm) after the delivery sensor is turned ON during the delivery operation.
0009
Delivery stationary 2
PI13,S9
When the delivery sensor detects a document after it is fed by a specified amount (100mm) after the
multifeed registration roller sensor is turned OFF during the delivery operation.
0010
Pre-reverse delay 1
S3
When the registration rear roller sensor fails to detect a document after it is fed by a specified amount
(50mm) after the startup of the reverse motor during the pre-reverse operation.
0011
Pre-reverse delay 2
S1,S3
When the reverse sensor fails to detect a document after it is fed by a specified amount (100mm) after
the registration roller rear sensor is turned ON during the pre-reverse operation.
0012
Pre-reverse delay 3
PI4
When the pre-reverse sensor fails to detect a document when the reverse motor is stopped during the pre-
reverse operation.
0013
Pre-reverse stationary 1
S1,S4
When the separation sensor detects a document after it is fed by a specified amount (169mm) after the
reverse sensor is turned ON during the pre-reverse operation.
0014
Pre-reverse stationary 2
S2,S4
When the registration roller front sensor detects a document after it is fed by a specified amount
(120mm) after the trailing edge of the sheet comes out of the separation pullout roller during the pre-
reverse operation.
0015
Pre-reverse stationary 3
S2,S3
When the registration roller rear sensor detects a document after it is fed by a specified amount (50mm)
after the trailing edge of the sheet comes out of the registration roller front sensor during the pre-reverse
operation.
0016
Pre-reverse stationary 4
S1,S3
When the reverse sensor detects a document after it is fed by a specified amount (100mm) after the
trailing edge of the sheet comes out of the registration roller rear sensor during the pre-reverse operation.
0017
Pre-reverse pickup delay
S1
When the reverse sensor fails to detect a document after it is fed by a specified amount (100mm) after
the startup of the reverse motor during the pre-reverse pickup operation.
0018
Pre-reverse pickup stationary
1
S1,PI4
When the pre-reverse sensor detects a document after it is fed by a specified amount after the reverse
sensor detects the leading edge of the sheet during the pre-reverse pickup operation.
0019
Pre-reverse pickup stationary
2
S1,PI4
When the reverse sensor detects a document after it is fed by a specified amount after the pre-reverse
sensor detects the trailing edge of the sheet during the pre-reverse pickup operation.
0020
Reverse pickup delay
S2
When the registration roller front sensor fails to detect a document after it is fed by a specified amount
(197mm) after the loop formation is completed during the reverse operation.
0021
Reverse pickup stationary
S2
When the registration roller front sensor detects a document after it is fed by a specified amount (length
of document x 1.5mm) after the registration roller front sensor is turned ON during the reverse operation.
0022
Pickup leading edge skew
S4,S5
When a difference in the leading edge detection timing between the separation sensor and the skew
sensor is 10mm or more during the separation operation.
0023
Pickup trailing edge skew
S4,S5
When a difference in the trailing edge detection timing between the separation sensor and the skew
sensor is 10mm or more during the pickup operation.
0024
Pickup NG 1
S1
When the reverse sensor detects a document before it comes out of the registration roller front sensor
during the pickup operation.
0025
Pickup NG 2
S3,S2
When the registration roller rear sensor detects a document before the reverse motor is started during the
pickup operation.When the registration roller front sensor fails to detect a document after it is fed by a
certain amount during the pickup operation.When the registration roller rear sensor detects a document
before the reverse motor is started during the pre-reverse operation.When the registration roller front
sensor fails to detect a document when the trailing edge of the document passes through the reverse
sensor during the reverse operation.
0026
Reverse pickup trailing edge
skew
S4,S5
When a difference in the trailing edge detection timing between the separation sensor and the skew
sensor is 10mm or more during the pre-reverse operation.
0027
Reverse pickup NG 1
PI4
When the pre-reverse sensor detects a document while the machine is waiting for the registration roller
front sensor to be turned ON during the reverse operation.
0030
Multifeeder registration
delay
S9
When the multifeed registration roller sensor fails to detect a document after a specified period of time
(1 sec) passes after the startup of the delivery motor during the multifeed loop formation.
0031
Multifeeder registration
stationary
S1
When the reverse sensor fails to detect a document after it is fed by a specified amount (638mm) after
the startup of belt motor during the multifeed pickup operation.
0032
Multifeeder reverse
stationary
S1
When the reverse sensor fails to detect a document after it is fed by a specified amount (50mm) after the
startup of the belt motor during the multifeed (platen roller) pickup operation.
0033
Multifeeder delivery delay
PI13
When the delivery sensor fails to detect a document after it is fed by a specified amount (621mm - length
of document) during the multifeed delivery operation.
0034
Multifeeder delivery
stationary
PI13
When the delivery sensor detects a document after it is fed by a specified amount (length of document x
1.5mm) after the delivery sensor is turned ON during the multifeed delivery operation.
0043
1st sheet pickup stationary 1 S3
When pickup stationary 1 (0003) occurs on the 1st sheet.
0044
1st sheet pickup stationary 2 S2
When pickup stationary 2 (0004) occurs on the 1st sheet.
0045
1st sheet reverse delay
S1
When reverse delay (0005) occurs on the 1st sheet.
0046
1st sheet reverse stationary
S1
When reverse stationary (0006) occurs on the 1st sheet.
0047
1st sheet delivery delay
PI13
When delivery delay (0007) occurs on the 1st sheet.
0048
1st sheet delivery stationary
1
PI13,S9
When delivery stationary 1 (0008) occurs on the 1st sheet.
Code
Type of Jam
Sensor No.
Details