Canon imagePRESS C1 Service Manual - page 1176
Chapter 16
16-279
OP-SZ-DT
Set ON/OFF of the document size detection function while the copyboard is open.
2
Setting range
0: Do not perform the document size detection while the copyboard is open.
- The document size must be manually entered in the control panel.
1: Perform the document size detection while the copyboard is open.
- Use this mode when you need to perform the document size detection automatically even when
you cannot close the copyboard to make copies of a thick book, etc.
- Detection is performed when the start key is pressed.
Standard value: 0
Remarks
When SIZE-DET is set to 0, the document size detection is not performed even when OP-SZ-DT
is set to 1.
NW-SCAN
Set whether or not to permit the network scan function.
2
0: Do not permit the network scan function.
1: Permit the network scan function.
Standard value: 0
HDCR-DSP
Switch the display/operation of HDD clear mode in the user mode.
2
Setting range
0: Do not perform clear.
1: Perform clear once with "0".
2: Perform clear once with random data.
3: Perform clear three times with random data.
Standard value: 1
MEMO: function for HDD initialization
This is the function to clear the data on HDD completely by overwriting the 0 (null) data and
random data to file data area at the moment of deleting files logically (timing for deleting the
administrative information data) in HDD.
JOB-INVL
Set the job interval for interruption.
2
Setting range
0: Normal setting (When an interruption copy occurs, print the next job continuously.)
1: After the last sheet of an interruption copy is delivered, start printing the next job.
2: After the last sheet of all jobs, start printing the next job.
Standard value: 0
LGSW-DSP
Use it to enable/disable display of 'enable/disable log indication' for Additional Functions Mode.
2
settings
0: do not display (default); 1: display
PCL-COPY
Binder control mode for COPIES command of PCL
2
This is the mode to unite the operations because the way to control the COPIES command of PCL
is different between the Canon PCL and the non-Canon PCL.
settings
0: [default] to control by page according to the value of COPIES command specified at each page.
1: It regards the value of COPIES command specified at page-1 as the number of bind, and invalid
the value of COPIES command of the following page and after (only at sort mode. in the case of
non-sort mode, it will be the same control as at '0' setting).
2 through 65535: backup
'0' is for control method with Canon. By setting '1', it will be the same control method with non-
Canon PCL.
PRJOB-CP
Set the CCV count pulse when performing reception and report printing.
2
Setting range
0: Do not provide a count pulse.
1: Provide a count pulse.
Standard value: 0
When using account-managing device (e.g., coin vendor, non-Canon control card), it switches
over (on/off) the count pulse notice for every page at receipt print/report print.
DPT-ID-7
Make a setting for registration of a section ID and entry of 7 digits for authentication.
2
Setting range
0: Same as a conventional method
1: 7 digits entry
Standard value
0
RUI-RJT
Disconnect the HTTP port when unauthorized authentication was performed from RUI three
times.
2
Setting range
0: Invalid
1: Valid
Standard value: 0
SND-RATE
SND-RATE (Set a compression ratio when the "high" compression ratio is selected for the Send
function.)
2
Setting range
0: Compression ratio: 1/16
1: Compression ratio: 1/20
2: Compression ratio: 1/24
When you increase a compression ratio, an image is deteriorated.
Standard value: 0
CTM-S06
Use it to enable/disable deletion of the password from an export file with a file transmission
address.
2
settings
0: do no delete (default); 1: delete
When setting '1', in the case of exporting the address book data from remote UI, the password of
file server is hidden from the exported file (to avoid leakage of information).
COPIER > OPTION > USER
Subheading Contents
Level