Canon imagePRESS C1 Service Manual - page 891
Chapter 15
15-28
0049
1st sheet delivery stationary
2
PI13,S9
When delivery stationary 2 (0009) occurs on the 1st sheet.
0050
1st sheet pre-reverse delay 1 S3
When pre-reverse delay 1 (0010) occurs on the 1st sheet.
0051
1st sheet pre-reverse delay 2 S1,S3
When pre-reverse delay 2 (0011) occurs on the 1st sheet.
0052
1st sheet pre-reverse delay 3 PI4
When pre-reverse delay 3 (0012) occurs on the 1st sheet.
0053
1st sheet pre-reverse
stationary 1
S1,S4
When pre-reverse stationary 1 (0013) occurs on the 1st sheet.
0054
1st sheet pre-reverse
stationary 2
S2,S4
When pre-reverse stationary 2 (0014) occurs on the 1st sheet.
0055
1st sheet pre-reverse
stationary 3
S2,S3
When pre-reverse stationary 3 (0015) occurs on the 1st sheet.
0056
1st sheet pre-reverse
stationary 4
S1,S3
When pre-reverse stationary 4 (0016) occurs on the 1st sheet.
0057
1st sheet pre-reverse pickup
delay
S1
When pre-reverse pickup delay (0017) occurs on the 1st sheet.
0058
1st sheet pre-reverse pickup
stationary 1
S1,PI4
When pre-reverse pickup stationary 1 (0018) occurs on the 1st sheet.
0059
1st sheet pre-reverse pickup
stationary 22
S1,PI4
When pre-reverse pickup stationary 2 (0019) occurs on the 1st sheet.
0060
1st sheet reverse pickup
delay
S2
When reverse pickup delay (0020) occurs on the 1st sheet.
0061
1st sheet reverse pickup
stationary
S2
When reverse pickup stationary (0021) occurs on the 1st sheet.
0062
1st sheet pickup leading edge
skew
S4,S5
When pickup leading edge skew (0022) occurs on the 1st sheet.
0063
1st sheet pickup trailing edge
skew
S4,S5
When pickup trailing edge skew (0023) occurs on the 1st sheet.
0064
1st sheet pickup NG 1
S1
When pickup NG 1 (0024) occurs on the 1st sheet.
0065
1st sheet pickup NG 2
S3,S2
When pickup NG 2 (0025) occurs on the 1st sheet.
0066
1st sheet reverse pickup
trailing edge skew
S4,S5
When reverse pickup trailing edge skew (0026) occurs on the 1st sheet.
0067
1st sheet reverse pickup NG
1
PI4
When reverse pickup NG 1 (0027) occurs on the 1st sheet.
0071
Timing error 1
-
Beyond control of software
0072
Timing error 2
-
When a previous document has yet to be delivered while a scanned document is moved to the right side
of the platen roller during the fixed reading.
0073
Illegal size
S3
When the registration roller rear sensor detects a document after it is fed by a specified amount (30mm)
from the waiting position during the LDR stream reading.
0074
Manual feed document size
error
S9,S1
When the reverse sensor detects a document while the multifeed registration roller sensor is detecting it
during the multifeed pickup operation.
0075
Image start position error
S7
When the reading position is not changed in response to a reading position change request during the
stream reading.
0076
1st sheet image start position
error
S7
When image start position error (0075) occurs on the 1st sheet.
0077
Belt speed setting error
PI1
When the specified speed of the belt motor is less than the minimum speed (100 mm/s) or more than the
maximum speed (700 mm/s).
0078
Belt speed switch error
PI1
When the belt motor is not in the normal speed when the belt motor speed is switched.
0079
Belt status error
PI1
When the belt motor status is not any of acceleration, normal, or deceleration when it is switched.
0080
Image start position output
timing error
S2,S3,SW301
When the image start position signal is output during acceleration while a document is fed from the
waiting position to the image start position during the stream reading.
0081
Reverse speed setting error
PI5
When the specified speed of the reverse motor is less than the minimum speed (100 mm/s) or more than
the maximum speed (700 mm/s).
0082
Reverse speed switch error
PI5
When the reverse motor is not in the normal speed when the reverse motor speed is switched.
0083
Reverse status error
PI5
When the reverse motor status is not any of acceleration, normal, or deceleration when it is switched.
0084
Last document error
PI1
A belt motor error occurs while a last document is being delivered or moved from the platen roller.
0085
Error
PI1,PI2,PI11
When a motor error other than IPC communication/ pickup error occurs. (less than three times)
0090
ADF open
PI10
When opening of the ADF is detected.
0091
User ADF open
PI10
When opening of the ADF is detected while the machine is in operation.
0092
Cover open
PI3,PI6
When opening of a cover (front or rear) is detected.
Code
Type of Jam
Sensor No.
Details