Canon imagePRESS C1 Service Manual - page 596
Chapter 9
9-59
F-9-179
9.7.25.4 After Replacing the Fixing Cleaning Web
0013-3407
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
Set the value clear '0' for the following service counters.
- COPIER> COUNTER> DRBL-1> FX-WEB
9.7.26 Insulating Bush
9.7.26.1 Preparation for Removing the Insulating Bush
0014-1196
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front door.
2) Pull out the fixing/feeding unit toward you.
3) Remove the fixing main heater/fixing sub heater. (page 9-54)Reference
[Removing the Fixing Main Heater/the Fixing Sub Heater]
9.7.26.2 Removing the Insulating Bush
0014-1197
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the 2 insulating bushes [1].
- 2 C-rings [2]
- 2 gears [3]
- 2 bearings [4]
- 1 holder [5]
Points to Note When Mounting the Insulating Bush
The orientation for mounting the insulating bushes is specified. Make sure to
mount according to the figure below.
F-9-180
9.7.26.3 After Replacing the Insulating Bush
0014-1198
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
- Apply grease (Molykote HP-300; CK-8012) to the inner diameter area [1]
and the outer diameter area [2] of the bushings for about 20 mg, so that to
make white coating in assigned areas.
Purpose: to avoid abnormal sound
F-9-181
- Make sure to wipe off the excessive grease because the grease adheres to
the both edges [1] of the fixing roller when mounting the greased bushes
to the fixing roller.
F-9-182
9.7.27 Outside Heat Insulating Bush
9.7.27.1 Preparation for Removing the External Heat
Insulating Bush
0014-1250
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front door.
2) Pull out the fixing/feeding unit toward you.
3) Remove the external heater. (page 9-56)Reference [Removing the Ex-
ternal Heater]
9.7.27.2 Removing the External Heat Insulating Bush
0014-1251
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the External Heat Insulating Bush [1].
- 2 C-rings [2]
- 2 washer [3]
- 2 bearings [4]
F-9-183
9.7.27.3 When Replacing the External Heat Insulating
Bush
0014-1252
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
[1]
[2]
[2]
[2]
[3]
[3]
[4]
[4]
[1]
[1]
[5]
[1]
[2]
[1]
[2]
[3]
[1]
[4]
[2]
[3]
[1]
[4]