Canon imagePRESS C1 Service Manual - page 441
Chapter 7
7-92
F-7-151
2) Detach the seal support plate (rear) [1].
- 2 screws [2]
F-7-152
When Mounting the Seal Support Plate (Front/Rear)
- When mounting the seal support plate (front/rear), make the seal support
plate [2] on the scoop-up sheet [1].
F-7-153
- When attaching the seal support plate (rear) [1], be sure to support the area
shown in [2] so that the seal support plate (rear) is not tilted.
F-7-154
7.14.15 Scoop-Up Sheet Support Plate
7.14.15.1 Preparation for Removing the Scoop-Up Sheet
Support Plate
0013-9790
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Remove the process unit cover.
3) Hold up the hopper unit.
4) Remove the primary corona assembly. (page 7-86)Reference [Remov-
ing the Primary Corona Assembly]
5) Remove the pre-transfer corona assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Detach the drum unit. (page 7-89)Reference [Removing the Drum Unit]
7) Detach the photosensitive drum. (page 7-90)Reference [Removing the
Photosensitive Drum]
8) Detach the drum cleaning pre-exposure LED unit. (page 7-86)Reference
[Removing the Drum Cleaning Pre-Exposure LED Unit]
7.14.15.2 Removing the Scoop-Up Sheet Support Plate
0013-9791
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Detach the scoop-up sheet support plate [1].
- 2 screws [2]
F-7-155
7.14.16 End Seal (Front)
7.14.16.1 Preparation for Removing the End Seal (Front)
0013-9741
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Detach the process unit cover.
3) Hold up the hopper unit.
4) Remove the primary corona assembly. (page 7-86)Reference [Remov-
ing the Primary Corona Assembly]
5) Remove the pre-transfer corona assembly. (page 7-88)Reference [Re-
moving the pre-transfer corona assembly]
6) Detach the drum unit. (page 7-89)Reference [Removing the Drum Unit]
7) Detach the drum cleaning blade. (page 7-93)Reference [Removing the
Drum Cleaning Blade]
7.14.16.2 Removing the End Seal (Front)
0013-9742
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Remove the end seal (front) [1].
- 1 screw [2]
F-7-156
7.14.17 End Seal (Rear)
7.14.17.1 Preparation for Removing the End Seal (Rear)
0013-9743
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the front cover.
2) Detach the process unit cover.
3) Hold up the hopper unit.
[2]
[3]
[4]
[4]
[4]
[1]
[2]
[2]
[1]
[1]
[2]
[1]
[1]
[1]
[2]
[1]
[2]
[1]
[1]
[2]
[2]
[1]