Canon imagePRESS C1 Service Manual - page 189
Chapter 2
2-95
F-2-364
11) Attach the hopper cover (Right) removed in step 3).
12) Close the upper right cover.
13) Close the toner replacement cover.
14) Connect the host machine's 2 power plugs (back, left) to 2 separate power
supply systems; then, turn on the main power switch.
15) Check to see that there is a message asking for a control card.
16) Connect a control card, and see that the host machine has become ready
for operation.
2.8.6 Installation Procedure in the imageWARE
Accounting Manager (henceforth: iWAM)
environment
0013-5327
imagePRESS C1 P / imagePRESS C1
1) Check to see that 'ID00000001 to ID00001000' have been created in '[Ad-
ditional Functions] > [System Settings] > [Dep ID Mangement] > [Regis-
tor Dept.ID/Password] / [Page Totals]' (In the case of entering '1' as the
first number in 'Service Mode > COPIER > FUNCTION > INSTALL >
CARD')
2) Press [Reset] to exit from [Additional Functions].
3) Select [Additional Functions] > [System Settings] > [Network Settings]
> [TCP/IP Settings] > [IP Address Settings], and then make the setting of
[IP Address], [Gateway Address], [Subnet Mask] according to the user
environment.
4) Press [Reset] to exit from [Additional Functions].
5)
[Additional Functions] > [System Settings] > [System Maneger Settings],
and then input any number into [System Maneger ID] and [System Pass-
word].
6) Press [Reset] to exit from [Additional Functions].
7) Go through the shut-down sequence to turn off the power.
2.8.7 Installation Procedure in the imageWARE
Accounting Manager (henceforth: iWAM)
Environment
0020-9582
imagePRESS C1+ (Printer) / imagePRESS C1+
1) Check to see that 'ID00000001 to ID00001000' have been created in '[Ad-
ditional Functions] > [System Settings] > [Dept. ID Mangement] >
[Registor Dept. ID/Password] / [Page Totals]' (In the case of entering '1'
as the first number in 'Service Mode > COPIER > FUNCTION > IN-
STALL > CARD')
2) Exit from [Additional Functions] screen.
3) Select [Additional Functions] > [System Settings] > [Network Settings]
> [TCP/IP Settings] > [IPv4 Settings] > [IP Address Settings], and then
make the setting of [IP Address], [Gateway Address], [Subnet Mask] ac-
cording to the user environment.
4) Exit from [Additional Functions] screen.
5)
[Additional Functions] > [System Settings] > [System Maneger Settings],
and then input any number into [System Maneger ID] and [System
Password].
6) Exit from [Additional Functions] screen.
7) Go through the shut-down sequence to turn off the power.
2.9 Installing the Original Tray
2.9.1 Checking the Contents
0015-0630
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
F-2-365
2.9.2 Checking the Contents
0021-2144
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
[Additional Functions] > [System Settings] > [System Maneger Settings] is
selected and [System Maneger ID] and [System Password] are registered,
'Registration of card to the device' is impossible to execute in the setting of
iWAM.
[1]
[2]
[3]
[4]
[Additional Functions] > [System Settings] > [System Maneger Settings] is
selected and [System Maneger ID] and [System Password] are registered,
'Registration of card to the device' is impossible to execute in the setting of
iWAM.
[1]
Document Tray
1 pc.
[2]
Washer
2 pc.
[3]
Stepped screw
2 pc.
[4]*
Stepped screw (M4)
2 pc.
* Not used in this host machine.
[1]
[3]
[2]
[4]