Canon imagePRESS C1 Service Manual - page 878
Chapter 15
15-15
E610
HDD encryption key fault
0001 A fault exists in the HDD encryption key (hardware configuration
error).
The encryption board is missing.
Ask the user to check the configuration of the hardware.
0002 A fault exists in the HDD encryption key (hardware configuration
error).
The requirements for the memory configuration (to execute
coding) are not fully met.
Ask the user to check the configuration of the hardware.
0101 A fault exists in the HDD encryption key (initialization error).
An attempt to initialize the key storage area has failed.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware.
0102 A fault exists in the HDD encryption key (initialization error).
An attempt to initialize the encryption processing area has failed.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware.
0201 A fault exists in the HDD encryption key.
An error exists in the encryption processing area has failed.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware.
0202 A fault exists in the HDD encryption key.
An error exists in the encryption processing area.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware.
0301 A fault exists in the HDD encryption key (encryption key error).
An attempt to create an encryption key has failed.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware.
0302 A fault exists in the HDD encryption key (encryption key error).
A fault has been detected in the encryption key.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware (SRAM). The error resets the data on the HDD.
0303 A fault exists in the HDD encryption key (encryption key error).
A fault has been detected in the encryption key.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware (SRAM). The error resets the data on the HDD.
0401 A fault exists in the HDD encryption key (encryption processing
error).
An error has been detected in the course of coding.
Turn off and then on the main power. If the remedy fails, it causes
by the hardware (encryption board).
0402 A fault exists in the HDD encryption key (encryption processing
error).
An error has been detected in the course of decoding
Turn off and then on the main power. If the remedy fails, it causes
by the hardware (encryption board).
E677
There is an external controller error.
0003 An error has been detected by a check on the configuration when
the external controller is being started up.
Turn off the main power, and check the cable; then, turn on the
main power.
If the machine fails to reset, re-install the system software of the
external controller.
0010 A controller for a non-Canon machine is connected.
Turn off the main power, and check the controller is an appropriate
type, and check the cable; then turn on the main power.
If the machine fails to reset, re-install the system software of the
external controller.
0080 There is an error in the communication with the printer after the
external controller has started up normally.
Turn off the main power, and check the cable; then, turn on the
main power.
If the machine fails to start up, re-install the system software of the
external controller.
E711
Error in IPC communication
0002 After losing communication between the finisher and the copier, 4
or more errors are detected within 1.5 sec.
Check the connection between the DC controller PCB and the
finisher. Replace the DC controller PCB.
E730
There is a PDL error.
1001 At the start of a job, an initialization error has occurred.
There is a fault in the PDL software.
Perform PDL resetting, or turn off and then on the main power.
100A A system error (e.g., failed initialization) has occurred during job
processing.
The PDL software has a fault.
Perform PDL resetting, or turn off and then on the main power.
100B At start-up, a mismatch occurs between the version number
indicated in the Master font management file of /BOOTDEV and
the bootable version.
There is no Master font management file in /BOOTDEV
There is an error in the PDL master-font
Perform PDL resetting, or turn off and then on the main power.
If the machine fails to reset, re-install the Kanji font file or fully
format and re-install the system software.
9004 There is an error in the PAI communication with the external
controller.
There is an OPEN/IF communication error.
Turn off the main power, and check the main controller PCB (sub
O-B) and the cable connection; then, turn on the main power.
If the machine fails to reset, replace the external controller, the
open I/F PCB, or the main controller PCB.
9005 There is an error in the connection of the video cable connected to
the external controller.
Turn off the main power, and check the main controller PCB (sub
O-B) and the cable connection; then, turn on the main power.
If the machine fails to reset, replace the external controller, the
open I/F PCB, or the main controller PCB.
A006 PDL does not respond, subbootable is out of order or does not
exist.
There is a PDL communication error.
Perform PDL resetting. Or turn off the main power and check the
connection of the rendering PCB, and then, turn on the main
power.
If the machine fails to reset, re-install the firmware or replace the
main controller PCB.
A007 At time of start-up, a mismatch occurs between the version of the
machine control software and the version of the PDL control
software.
The PDL version is wrong.
Perform PDL resetting, or turn off and then on the main power.
If the machine fails to reset, fully format and re-install the system
software.
B013 Indicates that font data are damaged at startup
Indicates the PDL embedded font failure
Turn off and then on the main power.
If the machine fails to reset, fully format and re-install the system
software.
Code
Cause (Detection Description)
Remedy