Canon imagePRESS C1 Service Manual - page 1231
Chapter 17
17-6
Installing the System Software
When downloaded, the system software is stored in the temporary storage area of the HDD. At the end of downloading, the main power switch must be turned off
and then back on, thus restarting the machine and writing the system software to both system area and flash ROM from the temporary storage area. When the main
power switch is turned off and then back on once again, the machine will start up using the new system software.
F-17-3
17.1.4 Points to Note at Time of Downloading
0013-8178
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / imagePRESS C1+
Do Not Turn Off the Power During Download/Write Operation
Do not turn off the power while the system software is being downloaded/written. Otherwise, the machine may fail to start up when its power is turned back on. (If
such is the case, execute HDD formatting, and download the system software. In the case of a boot ROM, replace the DIMM-ROM.)
Points to Note About Upgrading the DC Controller/Reader Controller
The DC controller/reader controller may be downloaded in either in normal mode or in safe mode. If done in safe mode, however, the controller version information
cannot be obtained, causing the data retained by the SST to be written over. It is a good idea, therefore, to use normal mode (so that the software will not be replaced
with software of a previous version).
17.2 Making Preparations
17.2.1 Installing the System Software (System CD -> SST)
0013-8179
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / imagePRESS C1+
Here, you will be copying the system software found on the System CD to the SST.
[Preparatory Work]
Requirements
- PC installed with SST version 3.22 or later
- System CD for this machine
[Installing the System Software]
Boot
ROM
FLASH
ROM
HDD
System
Software
System
Software
- - - Do
- - - Download Mode - - -
wnload Mode - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%
>>>>
wnload shell >>>>>
[ SYSTEM JPja-m ] - - - -
[ SYSTEM JPja-m ] - - - -
[ SYSTEM ZZ ] - - - - - - -
[ SYSTEM ZZ ] - - - - - - -
[ SYSTEM JPja-w ] - - - -
[ SYSTEM JPja-w ] - - - -
[ SYSTEM ZZ ] - - - - - - -
[ SYSTEM ZZ ] - - - - - - -
[ FONT F ] - - - - - - - - - -
[ FONT F ] - - - - - - - - - -
[ FONT G ] - - - - - - - - - -
[ FONT G ] - - - - - - - - - -
+++ Switch OFF the po
+++ Switch OFF the power then ON.
er then ON. +++
+++
Upg
Upgrading complete
ading complete
Upg
Upgrading complete
ading complete
Upg
Upgrading complete
ading complete
Upg
Upgrading complete
ading complete
Upg
Upgrading complete
ading complete
Upg
Upgrading complete
ading complete
- - - Do
- - - Download Mode - - -
wnload Mode - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -
[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -
[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -
[ iR2270iM-ZZjaxxxx-49AD
[ iR2270iM-ZZjaxxxx-49AD.PRG ] - - - - - - -
.PRG ] - - - - - - -
[ iR2270iW
[ iR2270iW-JPjaxxxx-5C16-MN.PRG ] - - - -
-JPjaxxxx-5C16-MN.PRG ] - - - -
[ iR2270iW
[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -
-ZZjaxxxx-A825.PRG ] - - - - - - -
[ iR2270iF-JPjaxxxx-DE96-ICC
[ iR2270iF-JPjaxxxx-DE96-ICC.PRG ] - - - -
.PRG ] - - - -
[ iR2270iW
[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -
-ZZjaxxxx-A825.PRG ] - - - - - - -
[ iR2270iG-JPjaxxxx-EC30-ICC
[ iR2270iG-JPjaxxxx-EC30-ICC.PRG ] - - - -
.PRG ] - - - -
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
Complete
HDD
System
Software
2)
1)
3)
The system software is downloaded.
Status of reception
(sample)
The main power switch is turned off and then on.
Writing takes place.
Temporary
storage area
Temporary
storage area
System area
4)
5)
The machine starts up using
the new version.
The main motor switch
is turned off and then on.