Canon imagePRESS C1 Service Manual - page 875
Chapter 15
15-12
E542
There is an error in up and down movement of the lower tray (finisher/saddle finisher).
8001 There is a clock error in up/down motor of the lower tray.
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
8002 Area error
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
0003 Safety switch activation
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
0004 In the case of detecting fault in clock
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
0005 In the case of detecting fault in speed
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
0006 In the case of detecting fault in accelerating time
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
0007 In the case of detecting Lock Detect signal
1)Check the No. 2 tray area sensors 1 through 3. Are the sensors
normal?
2)Check the wiring between the finisher controller PCB and the
No. 2 tray shift motor. Is the wiring normal?
3)Is there a fault in the up/down mechanism of the tray/
4)Try replacing the No. 2 shift motor. Is the problem corrected?
E584
There is an error in the shutter unit (finisher/saddle finisher).
8001 The shutter open sensor does not go off (i.e., the shutter is not
closed).
1)Check the shutter home position sensor. Is the sensor normal?
2)Check the wirings between the finisher controller PCB and the
stack edging motor, and between the finisher controller PCB and
the shutter open/closed clutch.
3)Is there a fault in the shutter mechanism?
4)Try replacing the stack edging motor or the shutter open/closed
clutch. Is the problem corrected?
0002 The shutter open sensor does not go on (i.e., the shutter does not
open).
1)Check the shutter home position sensor. Is the sensor normal?
2)Check the wirings between the finisher controller PCB and the
stack edging motor, and between the finisher controller PCB and
the shutter open/closed clutch.
3)Is there a fault in the shutter mechanism?
4)Try replacing the stack edging motor or the shutter open/closed
clutch. Is the problem corrected?
E590
There is an error in the punch motor (punch unit).
8001 The punching home position sensor is not detected when the
punch motor has been driven for 200 msec.
Check the punch home position sensor, the horizontal registration
motor, and the punch driver PCB; then, turn on the main power.
8002 The puncher does not detect the punching home position after the
motor has stopped (initial operation).
Check the punch home position sensor, the horizontal registration
motor, and the punch driver PCB; then, turn on the main power.
E591
There is an error in the punch dust sensor (punch unit).
8001 There is an error in the light-receiving voltage with emission of
light
Turn off and then on the main power.
8002 There is an error in the light-receiving voltage without emission of
light.
Turn off and then on the main power.
Code
Cause (Detection Description)
Remedy