Canon imagePRESS C1 Service Manual - page 876
Chapter 15
15-13
E592
There is an error in the punch horizontal registration sensor (punch unit).
8001 There is an error in the light-receiving voltage at time of light
emission (rear edge sensor).
Turn off and then on the main power.
8002 There is an error in the light-receiving voltage without emission of
light (rear edge sensor).
Turn off and then on the main power.
8003 There is an error in the light-receiving voltage with emission of
light (horizontal registration sensor 1).
Turn off and then on the main power.
8004 There is an error in the light-receiving voltage without emission of
light (horizontal registration sensor 1).
Turn off and then on the main power.
8005 There is an error in the light-receiving voltage with emission of
light (horizontal registration sensor 2).
Turn off and then on the main power.
8006 There is an error in the light-receiving voltage without emission of
light (horizontal registration sensor 2).
Turn off and then on the main power.
8007 There is an error in the light-receiving voltage with emission of
light (horizontal registration sensor 3).
Turn off and then on the main power.
8008 There is an error in the light-receiving voltage without emission of
light (horizontal registration sensor 3).
Turn off and then on the main power.
8009 There is an error in the light-receiving voltage with emission of
light (horizontal registration sensor 4).
Turn off and then on the main power.
800A There is an error in the light-receiving voltage without emission of
light (horizontal registration sensor 4).
Turn off and then on the main power.
E593
There is an error in the punch shift motor (punch unit).
8001 The light-receiving voltage HP sensor does not go off at time of
light emission.
Turn off and then on the main power.
8002 The light-receiving voltage HP sensor does not go on at time of no-
light emission
Turn off and then on the main power.
E5F0
There is an error in saddle paper positioning (saddle finisher).
0001 The paper positioning plate home position sensor does not turn on
when the paper positioning plate motor has been driven for 1.33
sec.
The paper poisoning plate motor (M4S)/the paper positioning
plate home position sensor (PI7S).
Check the paper positioning plate motor (M4S)/paper positioning
plate home position sensor (PI7S).
0002 The paper positioning plate home position sensor does not turn off
when the paper positioning plate motor has been driven for 1 sec.
The paper poisoning plate motor (M4S)/the paper positioning
plate home position sensor (PI7S)
Check the paper positioning plate motor (M4S)/paper positioning
plate home position sensor (PI7S).
E5F1
There is an error in saddle paper folding (saddle finisher).
0001 The number of detection pulses of the paper folding motor clock
sensor is lower than specified.
The paper folding motor (M2S)/the paper folding motor clock
sensor (PI4S)
Check the paper folding motor (M2S)/paper folding motor clock
sensor (PI4S)
0002 The state of the paper folding home position sensor does not
change when the paper folding motor has been driven for 3 sec.
The paper folding motor (M2S)/the paper folding motor clock
sensor (PI4S)
Check the paper folding motor (M2S)/paper folding motor clock
sensor (PI4S)
E5F2
There is an error in the saddle guide (saddle finisher).
0001 The guide home position sensor does not turn on when the guide
motor has been driven for 0.455 sec.
The guide motor (M3S)/the guide home position sensor (PI13S)
Check the guide motor (M3S)/guide home position sensor (PI13S)
0002 The guide home position sensor does not turn off when the guide
motor has been driven for 1 sec.
The guide motor (M3S)/the guide home position sensor (PI13S)
Check the guide motor (M3S)/guide home position sensor (PI13S)
E5F3
There is an error in saddle alignment (saddle finisher).
0001 The aligning plate home position sensor does not turn on when the
alignment motor has been driven for 0.5 sec.
The alignment motor (M5S)/the aligning plate home position
sensor (PI5S)
Check the alignment motor (M5S)/aligning plate home position
sensor (PI5S)
0002 The aligning plate home position sensor does not turn off when the
alignment motor has been driven for 1 sec.
The alignment motor (M5S)/the aligning plate home position
sensor (PI5S)
Check the alignment motor (M5S)/aligning plate home position
sensor (PI5S)
E5F4
There is an error in saddle rear stapling (saddle finisher).
0001 The stitching home position sensor does not turn on when the
stitch motor (rear) is rotated in reverse for 0.5 sec or more.
The stitch motor (rear, M6S)/stitching home position sensor (rear,
MS5S)
Check the stitching motor (rear, M6S)/stitching home position
sensor (rear, MS5S)
0002 The stitching home position sensor does not turn off when the
stitch motor (rear) is rotated for 0.5 sec or more.
The stitch motor (rear, M6S)/stitching home position sensor (rear,
MS5S)
Check the stitching motor (rear, M6S)/stitching home position
sensor (rear, MS5S)
E5F5
There is an error in saddle front stapling (saddle finisher).
0001 The stitching home position sensor does not turn on when the
stitch motor (front) is rotated in reverse for 0.5 sec or more.
The stitch motor (front, M7S)/stitching home position sensor
(front, MS7S)
Check the stitching motor (front, M7S)/stitching home position
sensor (front, MS7S)
0002 The stitching home position sensor does not turn off when the
stitch motor (front) is rotated for 0.5 sec or more.
The stitch motor (front, M7S)/stitching home position sensor
(front, MS7S)
Check the stitching motor (front, M7S)/stitching home position
sensor (front, MS5S)
Code
Cause (Detection Description)
Remedy