Canon imagePRESS C1 Service Manual - page 936
Chapter 16
16-39
(d) Jam code list (finisher-related)
T-16-50
(e) Jam code list (Feeder-specific)
T-16-51
0D90
transparency sensor (front, rear)
PS3, PS29
when the mode is transparency mode
0D91
transparency sensor (front, rear)
PS3, PS29
when the mode is not transparency mode
0D91
registration sensor
PS9
when the mode is transparency mode
0D92
transparency sensor (front, rear)
PS3, PS29
0D93
transparency sensor (front, rear)
PS3, PS29
Code
Sensor type
Sensor notation
1001
inlet path sensor feed delay jam
PI33
1002
punch path sensor (punch registration sensor) feed delay jam
LED5/PTR5
1004
delivery path sensor feed delay jam
PI34
1101
inlet path sensor feed stationary jam
PI33
1102
inlet path sensor feed stationary jam
punch path sensor (Punch registration sensor) feed stationary jam
LED5/PTR5
1104
delivery path sensor feed stationary jam
PI34
1200
timing jam
PI33
1500
stapler staple jam
STP
1300
power-on jam
PI33,PI34
1400
door open jam
DOOR
1644
punch jam
LED5/PTR5
1645
punch power-on jam
LED5/PTR5
1791
saddle feed sensor feed delay jam
PI18,PI19,PI20
1792
saddle delivery sensor feed delay jam
PI11
1793
saddle inlet sensor feed delay jam
PI22
17A1
saddle feed sensor feed stationary jam
PI18,PI19,PI20
17A2
saddle delivery sensor feed stationary jam
PI11,PI17
17A3
saddle inlet sensor feed stationary jam
PI22
1786
saddle stapler staple jam
S STP
1787
saddle power-on jam
PI11,PI18,PI19,PI20,PI22
1788
saddle door open jam
DOOR
Code
Sensor type
Sensor notation
Description
0001
post-separation sensor
PI7
the post-separation sensor does not detect paper when a feed of 452 mm has been made after
the start of separation.
0002
post-separation sensor
PI7
- the separation sensor detects paper after a feed of "500 mm (if extra length, +200 mm) - 45.5
mm" has been made.
- the sensor goes on within a feed of 12 mm after detection of the trailing edge (holed paper);
the post-separation sensor detects paper when a feed of 50 m has been made after the
separation sensor goes on.
0003
registration sensor
PI1
the registration sensor does not detect paper when a feed of 134.8 mm has been made after
the post-separation sensor goes on.
0004
registration sensor
PI1
the read sensor goes off before the registration sensor goes off.
0005
feed sensor
PI8
- read sensor does not detect paper when a feed of 364.2 mm (182.1 x 2) has been made from
the point of registration.
- the read sensor does not detect paper when a feed of 157.4 mm (78.7 x 2) has been made
from the point of No. 2 registration.
0006
feed sensor
PI8
- the read sensor detects paper when a feed of 500 mm (if extra-length, +200 mm) has been
made from the start of feed after a temporary stop at point of reading.
- the read sensor detects paper when a feed of 514 mm has been made after the start of feed
from the standby point in mix mode (LTRR/LGL identified).
0007
delivery reversal sensor
PI9
- if not in high-speed duplex mode, the delivery sensor does not detect when a feed of 132.1
mm has been made after paper has reached the leading edge downstream roller with respect
to the activation of the read sensor.
- the delivery sensor does not detect paper when a feed of 50 mm has been made after the start
of feed during a switch-back operation.
0008
delivery reversal sensor
PI9
the delivery sensor detects paper when a feed of 161.9 mm has been made from the end of
reading the trailing edge.
0042
post-separation sensor
PI7
1st; stationary jam at the post-separation sensor
0043
registration sensor
PI1
1st; not reaching the registration sensor
0044
registration sensor
PI1
1st; stationary at the registration sensor
Code
Sensor type
Sensor
number
Remarks