Canon imagePRESS C1 Service Manual - page 187
Chapter 2
2-93
When moving host machine to another place after installation, perform the
following operations.
1) Take all papers out from each cassette.
2) Push the power switch of the control panel for 3 sec or more, and operate
the touch panel according to the screen display of the shutdown sequence
(The main power switch automatically turns off).
3) Disconnect the 2 power plugs (1 on the back of the host machine, 1 on the
left side of the host machine) of the host machine.
4) Secure the scanner with the scanner fixing screw stored at installation.
5) Remove the developing assembly for each color and the toner container
for each color and move them in other packagings.
6) After removing the developing assembly for each color, cover the toner
supply mouth [1] of the developing rotary with vinyl tape.
F-2-354
7) Be sure to secure the developing assembly fixed arm with screw.
8) Affix tape to the release lever of the fixing feeder assembly to prevent it
from being fallen out due to vibration.
9) Affix each cover and each cassette with tape.
10) Place an A3 copy paper on the copyboard glass, and affix tape to the
ADF.
11) When walking the stairs to carry in / out the equipment at the installation
place, take into account the followings.
- Be sure to detach the caster cover and check to see that the 2 adjusters on
the bottom of the host machine are completely tightened.
- If accessory such as side paper deck and finisher has been installed, carry
in / out the host machine after removing them.
12) For re-installation after moving, be sure to secure the machine in place
with the 2 adjusters and fix the caster cover with the 2 screws before per-
forming the operation.
2.8 Installing the Card Reader
2.8.1 Points to Note About Installation
0013-4823
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
2.8.2 Checking the Contents
0013-4819
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
F-2-355
F-2-356
2.8.3 Pre-Settings
0020-7219
imagePRESS C1+ (Printer) / imagePRESS C1+
1) (COPIER>FUNCTION>INSTALL>CARD), enter a card number (1
through 2001).
- Enter the lowest number of those to be used by the user.
- As many as 1000 numbers (i.e., cards) may be used starting with the
number entered here.
2.8.4 Turning Off the Machine
0013-4894
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
See the host machine installation [Points to note at the main power OFF].
2.8.5 Installation Procedure
0013-4926
imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-
PRESS C1+
1) Open the toner replacement cover [1].
2) Open the upper right cover [2].
Incomplete tightening of the adjuster may cause its breakage when the
machine climbs over the step.
Installation of the card reader calls for a Card Reader Attachment-E1.
[1]
[1]
Card reader
1 pc.
[2]*
Screw (RS tightening; M4X10)
1 pc.
[3]*
Toothed washer
1 pc.
* Not used in this host machine.
[1]
card reader mounting base
1 pc.
[2]
Screw (TP; M4X8)
2 pc.
[3]
Toothed washer
1 pc.
[4]
Stepped screw
2 pc.
C
[1]
[2]
[3]
[1]
[2]
[3]
[4]