Canon imagePRESS C1 Service Manual - page 1157
Chapter 16
16-260
FXWRNLVL
Change the warning level of the fixing upper roller.
Change the warning level of the fixing counter value. The life of the fixing roller differs
depending on the environment and usage. Set this value to match the optimum life when replacing
the fixing unit.
2
Setting range
0: 180,000
1: 150,000
2: 120,000
Standard value: 0
The setting value becomes valid after the main power switch is turned OFF/ON.
FXERRLVL
Change an error level of the fixing roller.
Specify an error level of the fixing counter value. Specify a counter value from when a warning
is displayed to when an error is displayed.
2
This mode is not used for this machine.
DA-PORT
Set a port for communication with DA.
2
Setting range
1: Open
0: Close
Standard value: 0
When 1 is set to COPIER > OPTION > BODY > DA-CNCT, the following items are set to ON.
COPIER > OPTION > BODY > STS-PORT
> CMD-PORT
> SSH-SW
> DA-PORT
DA-CNCT
Use it to set WPGW(Workplace Gateway) connection.
2
settings
0: off (default); 1: on
MEMO:
This is used only inside Japan, not outside Japan.
1TR-ATVC
Set ON/OFF of the primary transfer ATVC retries for initial multiple rotations.
Turn ON the primary transfer ATVC retries for initial multiple rotations in all environments.
2
This mode is not used for this machine.
CHNG-STS
Use it to set the T.O.T (TUIF over TCP/IP) status connection port number.
2
Changes the port number for status connection in a TUIF over TCP/IP environment. This is used
for changing the port No. in service NAVI.
settings: 1 to 65535 (default: 20010)
MEMO:
T.O.T (TUIF over TCP/IP)
Communication protocol between embedded application presentation (UI) and applications
within the device including COPY/SEND/BOX etc., (Canon original protocol)
CHNG-CMD
Use it to set the T.O.T (TUIF over TCP/IP) command connection port number.
2
Use it to set the port number for the command connection in an TUIF over TCP/IP environment.
This is used for changing the port No. in service NAVI.
settings: 1 to 65535 (default: 20000)
MEMO:
T.O.T (TUIF over TCP/IP)
Communication protocol between embedded application presentation (UI) and applications
within the device including COPY/SEND/BOX etc., (Canon original protocol)
MEAP-DSP
Use it to prohibit a switch-over from the MEAP screen to the standard screen (COPY/SEND/BOX
screen etc.,).
2
settings
0: off (shift to standard screen; default); 1: on (do not shift to atandard screen)
MEMO:
Although setting the value as '1' in COPIER > OPTION > BODY > MEAP-DSP, at the occurrence
of error/jam/alarm, the display transits to the standard screen for showing a warning.
ANIM-SW
Set whether or not to use the full-screen display for jam/alarm in MEAP application operation.
2
Although setting the value as '1' in COPIER > OPTION > BODY > MEAP-DSP, at the occurrence
of error/jam/alarm, the display transits to the standard screen for showing a warning.
When setting this value as '1', at the occurrence of error/jam/alarm,
- Display transition to the standard screen is prohibited.
- Warning is displayed on the MEAP screen to urge the user to contact servicing.
settings
0: off (display warning screen; default); 1: on (do not display warning screen)
HDD-TMP
Set a temperature for judgment of an abnormal status with low temperature in SAMSUNG HDD.
2
Setting range: 0 to 30 (deg C)
Standard value: 2
The setting value becomes valid after the main power switch is turned OFF/ON.
HDD-TIM
Set the grace time until it is judged as an abnormal status with low temperature in SAMSUNG
HDD.
2
Setting range: 0 to 200 (minute)
Standard value: 10
The setting value becomes valid after the main power switch is turned OFF/ON.
HDD-SW
Set whether or not to display the E code for an abnormal status with low temperature in
SAMSUNG HDD.
2
Setting range
0: Do not display the code.
1: Display the code.
Standard value: 0
The setting value becomes valid after the main power switch is turned OFF/ON.
COPIER > OPTION > BODY
Subheading Contents
Level